[PATCH 0/3] Thermal monitor on PM660

[PATCH 0/3] Thermal monitor on PM660

[Richard Acayan]

This series adds the ADC thermal monitor on PM660. It also fixes the
scaling between voltage and temperature for the HC variant.

Richard Acayan (3):
  dt-bindings: mfd: qcom,spmi-pmic: Allow PMIC4 thermal monitor on pm660
  thermal: qcom-spmi-adc-tm5: Correct the voltage-code scaling for HC
  arm64: dts: qcom: pm660: add thermal monitor

 .../devicetree/bindings/mfd/qcom,spmi-pmic.yaml        |  1 +
 arch/arm64/boot/dts/qcom/pm660.dtsi                    | 10 ++++++++++
 drivers/thermal/qcom/qcom-spmi-adc-tm5.c               |  2 +-
 3 files changed, 12 insertions(+), 1 deletion(-)

-- 
2.53.0

[PATCH 1/3] dt-bindings: mfd: qcom,spmi-pmic: Allow PMIC4 thermal monitor on pm660

[Richard Acayan]

While newer PMICs are compatible with PMIC5 drivers, the PM8998 and
PM660 are both PMIC4. The PM8998 is allowed to use the PMIC4 thermal
monitor. Allow it for PM660 as well.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
index 65c80e3b4500..d2fce7f669b2 100644
--- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
+++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
@@ -221,6 +221,7 @@ allOf:
         compatible:
           contains:
             enum:
+              - qcom,pm660
               - qcom,pm8998
     then:
       patternProperties:
-- 
2.53.0

Re: [PATCH 1/3] dt-bindings: mfd: qcom,spmi-pmic: Allow PMIC4 thermal monitor on pm660

[Konrad Dybcio]

On 2/10/26 3:18 AM, Richard Acayan wrote:
> While newer PMICs are compatible with PMIC5 drivers, the PM8998 and
> PM660 are both PMIC4. The PM8998 is allowed to use the PMIC4 thermal
> monitor. Allow it for PM660 as well.
> 
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH 1/3] dt-bindings: mfd: qcom,spmi-pmic: Allow PMIC4 thermal monitor on pm660

[Krzysztof Kozlowski]

On Mon, Feb 09, 2026 at 09:18:17PM -0500, Richard Acayan wrote:
> While newer PMICs are compatible with PMIC5 drivers, the PM8998 and
> PM660 are both PMIC4. The PM8998 is allowed to use the PMIC4 thermal
> monitor. Allow it for PM660 as well.
> 
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---
>  Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 1 +
>  1 file changed, 1 insertion(+)

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

[PATCH 2/3] thermal: qcom-spmi-adc-tm5: Correct the voltage-code scaling for HC

[Richard Acayan]

When support was added for the HC variant, the full_scale_code_volt
value was copied from the tm5 variant. From the downstream kernel, the
scaling value is 0x70e4 on PMI632 (tm5 variant), but it is 0x4000 on
PM660 and PM8998 (HC variant). Correct the ADC code to voltage
scaling factor for the HC variant.

Fixes: f6c83676c6097 ("thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant")
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 drivers/thermal/qcom/qcom-spmi-adc-tm5.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
index d7f2e6ca92c2..6ccd02fe0e4c 100644
--- a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
+++ b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c
@@ -909,7 +909,7 @@ static const struct adc_tm5_data adc_tm5_data_pmic = {
 };
 
 static const struct adc_tm5_data adc_tm_hc_data_pmic = {
-	.full_scale_code_volt = 0x70e4,
+	.full_scale_code_volt = 0x4000,
 	.decimation = (unsigned int []) { 256, 512, 1024 },
 	.hw_settle = (unsigned int []) { 0, 100, 200, 300, 400, 500, 600, 700,
 					 1000, 2000, 4000, 6000, 8000, 10000 },
-- 
2.53.0

Re: [PATCH 2/3] thermal: qcom-spmi-adc-tm5: Correct the voltage-code scaling for HC

[Konrad Dybcio]

On 2/10/26 3:18 AM, Richard Acayan wrote:
> When support was added for the HC variant, the full_scale_code_volt
> value was copied from the tm5 variant. From the downstream kernel, the
> scaling value is 0x70e4 on PMI632 (tm5 variant), but it is 0x4000 on
> PM660 and PM8998 (HC variant). Correct the ADC code to voltage
> scaling factor for the HC variant.
> 
> Fixes: f6c83676c6097 ("thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant")
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---

nice catch!

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH 2/3] thermal: qcom-spmi-adc-tm5: Correct the voltage-code scaling for HC

[Dmitry Baryshkov]

On Mon, Feb 09, 2026 at 09:18:18PM -0500, Richard Acayan wrote:
> When support was added for the HC variant, the full_scale_code_volt
> value was copied from the tm5 variant. From the downstream kernel, the
> scaling value is 0x70e4 on PMI632 (tm5 variant), but it is 0x4000 on
> PM660 and PM8998 (HC variant). Correct the ADC code to voltage
> scaling factor for the HC variant.
> 
> Fixes: f6c83676c6097 ("thermal/drivers/qcom/spmi-adc-tm5: Add support for HC variant")
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---
>  drivers/thermal/qcom/qcom-spmi-adc-tm5.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>

> 
-- 
With best wishes
Dmitry

[PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Richard Acayan]

The thermal monitor is used to monitor arbitrary ADC-based thermal
sensors. It is suitable for use in thermal zones. Add support for it in
PM660.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
 arch/arm64/boot/dts/qcom/pm660.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm660.dtsi b/arch/arm64/boot/dts/qcom/pm660.dtsi
index 156b2ddff0dc..7cedf6980b34 100644
--- a/arch/arm64/boot/dts/qcom/pm660.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm660.dtsi
@@ -197,6 +197,16 @@ channel@85 {
 			};
 		};
 
+		pm660_adc_tm: adc-tm@3400 {
+			compatible = "qcom,spmi-adc-tm-hc";
+			reg = <0x3400>;
+			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		pm660_rradc: adc@4500 {
 			compatible = "qcom,pm660-rradc";
 			reg = <0x4500>;
-- 
2.53.0

Re: [PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Konrad Dybcio]

On 2/10/26 3:18 AM, Richard Acayan wrote:
> The thermal monitor is used to monitor arbitrary ADC-based thermal
> sensors. It is suitable for use in thermal zones. Add support for it in
> PM660.
> 
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---
>  arch/arm64/boot/dts/qcom/pm660.dtsi | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/pm660.dtsi b/arch/arm64/boot/dts/qcom/pm660.dtsi
> index 156b2ddff0dc..7cedf6980b34 100644
> --- a/arch/arm64/boot/dts/qcom/pm660.dtsi
> +++ b/arch/arm64/boot/dts/qcom/pm660.dtsi
> @@ -197,6 +197,16 @@ channel@85 {
>  			};
>  		};
>  
> +		pm660_adc_tm: adc-tm@3400 {
> +			compatible = "qcom,spmi-adc-tm-hc";
> +			reg = <0x3400>;
> +			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
> +			#thermal-sensor-cells = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";

Can we enable it by default?

Konrad

Re: [PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Richard Acayan]

On Tue, Feb 10, 2026 at 10:59:20AM +0100, Konrad Dybcio wrote:
> On 2/10/26 3:18 AM, Richard Acayan wrote:
(snip)
> > +		pm660_adc_tm: adc-tm@3400 {
> > +			compatible = "qcom,spmi-adc-tm-hc";
> > +			reg = <0x3400>;
> > +			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
> > +			#thermal-sensor-cells = <1>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			status = "disabled";
> 
> Can we enable it by default?

No, the thermal monitor fails to probe if it doesn't have any channels:

	[   17.728926] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: error -EINVAL: get dt data failed
	[   17.728945] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: probe with driver qcom-spmi-adc-tm5 failed with error -22

Triggered by https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/thermal/qcom/qcom-spmi-adc-tm5.c?h=next-20260209#n945

Re: [PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Konrad Dybcio]

On 2/11/26 1:29 AM, Richard Acayan wrote:
> On Tue, Feb 10, 2026 at 10:59:20AM +0100, Konrad Dybcio wrote:
>> On 2/10/26 3:18 AM, Richard Acayan wrote:
> (snip)
>>> +		pm660_adc_tm: adc-tm@3400 {
>>> +			compatible = "qcom,spmi-adc-tm-hc";
>>> +			reg = <0x3400>;
>>> +			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
>>> +			#thermal-sensor-cells = <1>;
>>> +			#address-cells = <1>;
>>> +			#size-cells = <0>;
>>> +			status = "disabled";
>>
>> Can we enable it by default?
> 
> No, the thermal monitor fails to probe if it doesn't have any channels:
> 
> 	[   17.728926] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: error -EINVAL: get dt data failed
> 	[   17.728945] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: probe with driver qcom-spmi-adc-tm5 failed with error -22
> 
> Triggered by https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/thermal/qcom/qcom-spmi-adc-tm5.c?h=next-20260209#n945

You can define the following ones in the common dt:

REF_GND
1.25VREF
VREF_VADC
VPH_PWR
VCOIN
DIE_TEMP
ANA_IN

as they're (almost or) always going to be present

Konrad

Re: [PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Richard Acayan]

On Thu, Feb 12, 2026 at 01:15:04PM +0100, Konrad Dybcio wrote:
> On 2/11/26 1:29 AM, Richard Acayan wrote:
> > On Tue, Feb 10, 2026 at 10:59:20AM +0100, Konrad Dybcio wrote:
> >> On 2/10/26 3:18 AM, Richard Acayan wrote:
> > (snip)
> >>> +		pm660_adc_tm: adc-tm@3400 {
> >>> +			compatible = "qcom,spmi-adc-tm-hc";
> >>> +			reg = <0x3400>;
> >>> +			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
> >>> +			#thermal-sensor-cells = <1>;
> >>> +			#address-cells = <1>;
> >>> +			#size-cells = <0>;
> >>> +			status = "disabled";
> >>
> >> Can we enable it by default?
> > 
> > No, the thermal monitor fails to probe if it doesn't have any channels:
> > 
> > 	[   17.728926] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: error -EINVAL: get dt data failed
> > 	[   17.728945] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: probe with driver qcom-spmi-adc-tm5 failed with error -22
> > 
> > Triggered by https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/thermal/qcom/qcom-spmi-adc-tm5.c?h=next-20260209#n945
> 
> You can define the following ones in the common dt:
> 
> REF_GND

Is there any (likely passive, if any) cooling device that should be
activated when this goes above or below a certain reading?

> 1.25VREF
> VREF_VADC
> VPH_PWR
> VCOIN
> DIE_TEMP

Maybe this temperature can be included, but I don't see any other
PMIC devicetree that has this channel ready-to-go.

> ANA_IN

Re: [PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Konrad Dybcio]

On 2/12/26 7:27 PM, Richard Acayan wrote:
> On Thu, Feb 12, 2026 at 01:15:04PM +0100, Konrad Dybcio wrote:
>> On 2/11/26 1:29 AM, Richard Acayan wrote:
>>> On Tue, Feb 10, 2026 at 10:59:20AM +0100, Konrad Dybcio wrote:
>>>> On 2/10/26 3:18 AM, Richard Acayan wrote:
>>> (snip)
>>>>> +		pm660_adc_tm: adc-tm@3400 {
>>>>> +			compatible = "qcom,spmi-adc-tm-hc";
>>>>> +			reg = <0x3400>;
>>>>> +			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
>>>>> +			#thermal-sensor-cells = <1>;
>>>>> +			#address-cells = <1>;
>>>>> +			#size-cells = <0>;
>>>>> +			status = "disabled";
>>>>
>>>> Can we enable it by default?
>>>
>>> No, the thermal monitor fails to probe if it doesn't have any channels:
>>>
>>> 	[   17.728926] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: error -EINVAL: get dt data failed
>>> 	[   17.728945] qcom-spmi-adc-tm5 c440000.spmi:pmic@0:adc-tm@3400: probe with driver qcom-spmi-adc-tm5 failed with error -22
>>>
>>> Triggered by https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/drivers/thermal/qcom/qcom-spmi-adc-tm5.c?h=next-20260209#n945
>>
>> You can define the following ones in the common dt:
>>
>> REF_GND
> 
> Is there any (likely passive, if any) cooling device that should be
> activated when this goes above or below a certain reading?

I don't think so

> 
>> 1.25VREF
>> VREF_VADC
>> VPH_PWR
>> VCOIN
>> DIE_TEMP
> 
> Maybe this temperature can be included, but I don't see any other
> PMIC devicetree that has this channel ready-to-go.

This channel is internally connected and handled by temp_alarm, I think
describing it via the ADC just lets one peek into the raw values

Konrad

> 
>> ANA_IN

Re: [PATCH 3/3] arm64: dts: qcom: pm660: add thermal monitor

[Richard Acayan]

On Tue, Feb 10, 2026 at 10:59:20AM +0100, Konrad Dybcio wrote:
> On 2/10/26 3:18 AM, Richard Acayan wrote:
> > The thermal monitor is used to monitor arbitrary ADC-based thermal
> > sensors. It is suitable for use in thermal zones. Add support for it in
> > PM660.
> > 
> > Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> > ---
> >  arch/arm64/boot/dts/qcom/pm660.dtsi | 10 ++++++++++
> >  1 file changed, 10 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/pm660.dtsi b/arch/arm64/boot/dts/qcom/pm660.dtsi
> > index 156b2ddff0dc..7cedf6980b34 100644
> > --- a/arch/arm64/boot/dts/qcom/pm660.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/pm660.dtsi
> > @@ -197,6 +197,16 @@ channel@85 {
> >  			};
> >  		};
> >  
> > +		pm660_adc_tm: adc-tm@3400 {
> > +			compatible = "qcom,spmi-adc-tm-hc";
> > +			reg = <0x3400>;
> > +			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
> > +			#thermal-sensor-cells = <1>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			status = "disabled";
> 
> Can we enable it by default?

This is for the ADC thermal monitor, and not the ADC itself. I don't see
the need to allocate channels just so this can be enabled by default,
since the thermal monitor's purpose is mostly to send interrupts when
the ADC values go above or below a certain threshold.