From: Philip Radford <philip.radford@arm.com>
To: Sudeep Holla <sudeep.holla@kernel.org>
Cc: linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, arm-scmi@vger.kernel.org,
linux-pm@vger.kernel.org, james.quinlan@broadcom.com,
f.fainelli@gmail.com, vincent.guittot@linaro.org,
etienne.carriere@st.com, peng.fan@oss.nxp.com,
michal.simek@amd.com, quic_sibis@quicinc.com,
dan.carpenter@linaro.org, d-gole@ti.com,
souvik.chakravarty@arm.com,
Cristian Marussi <cristian.marussi@arm.com>
Subject: Re: [PATCH v9 04/13] firmware: arm_scmi: Add SCMIv4.0 Powercap basic support
Date: Thu, 15 Oct 2026 14:15:04 +0100 [thread overview]
Message-ID: <atDPwqwoYWqeFKdJ@e121740.arm.com> (raw)
In-Reply-To: <20261015-sarcastic-accurate-kestrel-585cc2@sudeepholla>
On Thu, Oct 15, 2026 at 01:57:14PM +0100, Sudeep Holla wrote:
> On Wed, Sep 09, 2026 at 10:04:28PM +0000, Philip Radford wrote:
> > From: Cristian Marussi <cristian.marussi@arm.com>
> >
> > Add SCMIv4.0 Powercap support for enumerating multiple CPLs of a domain
> > when available.
> >
> > Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
> > [Philip: Fixed sparse issues where int was expected]
> > Signed-off-by: Philip Radford <philip.radford@arm.com>
> > ---
Hi,
Thanks for looking at the series.
> > V8->V9
> > - included validation of the number of cpls in iter_powercap_cpls_update_state
> > - re-ordered validation of cap_config and num_cpli in powercap_domain_attrs_process
> > - included validation of length in powercap_domain_attributes_get
> > - amended cap_get and cap_set referencing apl_id array index instead fo firmware CPL identifier
> > - added bounds check to make sure cpl_id is less than num_cpli
> > ---
> > drivers/firmware/arm_scmi/powercap.c | 495 ++++++++++++++++++++++-----
> > drivers/powercap/arm_scmi_powercap.c | 2 +-
> > include/linux/scmi_protocol.h | 1 +
> > 3 files changed, 402 insertions(+), 96 deletions(-)
> >
> > diff --git a/drivers/firmware/arm_scmi/powercap.c b/drivers/firmware/arm_scmi/powercap.c
> > index 4666030176c3..7ee39434a4db 100644
> > --- a/drivers/firmware/arm_scmi/powercap.c
> > +++ b/drivers/firmware/arm_scmi/powercap.c
> > @@ -33,6 +33,7 @@ enum scmi_powercap_protocol_cmd {
> > POWERCAP_CAP_NOTIFY = 0xa,
> > POWERCAP_MEASUREMENTS_NOTIFY = 0xb,
> > POWERCAP_DESCRIBE_FASTCHANNEL = 0xc,
> > + POWERCAP_CPC_ATTRIBUTES = 0xd,
> > };
> >
> > enum {
> > @@ -69,17 +70,56 @@ struct scmi_msg_resp_powercap_domain_attributes {
> > __le32 parent_id;
> > };
> >
> > +struct scmi_msg_resp_powercap_domain_attributes_v3 {
> > + __le32 attributes;
> > +#define SUPPORTS_POWERCAP_MAI_CONFIGURATION(x) ((x) & BIT(25))
> > +#define SUPPORTS_POWERCAP_FASTCHANNELS(x) ((x) & BIT(22))
> > +#define SUPPORTS_POWERCAP_CAP_CHANGE_NOTIFY_V3(x) ((x) & BIT(21))
> > +#define SUPPORTS_POWERCAP_CAI_CONFIGURATION(x) ((x) & BIT(20))
> > + u8 name[SCMI_SHORT_NAME_MAX_SIZE];
> > + __le32 min_mai;
> > + __le32 max_mai;
> > + __le32 mai_step;
> > + __le32 min_power_cap;
> > + __le32 max_power_cap;
> > + __le32 power_cap_step;
> > + __le32 sustainable_power;
> > + __le32 accuracy;
> > + __le32 parent_id;
> > + __le32 min_cai;
> > + __le32 max_cai;
> > + __le32 cai_step;
> > +};
> > +
> > +struct scmi_msg_powercap_get_v3 {
> > + __le32 domain_id;
> > + __le32 cpli;
> > +};
> > +
> > struct scmi_msg_powercap_set_cap_or_pai {
> > - __le32 domain;
> > + __le32 domain_id;
> > __le32 flags;
> > #define CAP_SET_ASYNC BIT(1)
> > #define CAP_SET_IGNORE_DRESP BIT(0)
> > __le32 value;
> > };
> >
> > +struct scmi_msg_powercap_set_cap_v3 {
> > + __le32 domain_id;
> > + __le32 cpli;
> > + __le32 flags;
> > + __le32 power_cap;
> > +};
> > +
> > struct scmi_msg_resp_powercap_cap_set_complete {
> > - __le32 domain;
> > + __le32 domain_id;
> > + __le32 power_cap;
> > +};
> > +
> > +struct scmi_msg_resp_powercap_cap_set_complete_v3 {
> > + __le32 domain_id;
> > __le32 power_cap;
> > + __le32 cpli;
> > };
> >
> > struct scmi_msg_resp_powercap_meas_get {
> > @@ -112,6 +152,33 @@ struct scmi_powercap_meas_changed_notify_payld {
> > __le32 power;
> > };
> >
> > +struct scmi_msg_powercap_cpc {
> > + __le32 domain_id;
> > + __le32 desc_index;
> > +};
> > +
> > +struct scmi_msg_resp_powercap_cpc {
> > + __le32 num_cpl;
> > +#define NUM_RETURNED(n) (le32_get_bits((n), GENMASK(15, 0)))
> > +#define NUM_REMAINING(n) (le32_get_bits((n), GENMASK(31, 16)))
> > + struct {
> > + __le32 cpli;
> > + __le32 flags;
> > + __le32 min_power_cap;
> > + __le32 max_power_cap;
> > + __le32 power_cap_step;
> > + __le32 min_cai;
> > + __le32 max_cai;
> > + __le32 cai_step;
> > + u8 name[SCMI_SHORT_NAME_MAX_SIZE];
> > + } desc[];
> > +};
> > +
> > +struct scmi_cpls_priv {
> > + u32 domain_id;
> > + struct scmi_powercap_cpl_info *cpli;
> > +};
> > +
> > struct scmi_powercap_state {
> > bool enabled;
> > u32 last_pcap;
> > @@ -129,6 +196,11 @@ struct powercap_info {
> > bool notify_measurements_cmd;
> > struct scmi_powercap_state *states;
> > struct scmi_powercap_info *powercaps;
> > + int (*xfer_cap_get)(const struct scmi_protocol_handle *ph,
> > + const struct scmi_powercap_info *pc, u32 cpl_id, u32 *power_cap);
> > + int (*xfer_cap_set)(const struct scmi_protocol_handle *ph,
> > + const struct scmi_powercap_info *pc,
> > + u32 cpl_id, u32 power_cap, bool ignore_dresp);
> > };
> >
> > static enum scmi_powercap_protocol_cmd evt_2_cmd[] = {
> > @@ -192,18 +264,227 @@ scmi_powercap_validate(unsigned int min_val, unsigned int max_val,
> > return 0;
> > }
> >
> > +static void iter_powercap_cpls_prepare_message(void *message,
> > + unsigned int desc_index,
> > + const void *priv)
> > +{
> > + struct scmi_msg_powercap_cpc *msg = message;
> > + const struct scmi_cpls_priv *p = priv;
> > +
> > + msg->domain_id = cpu_to_le32(p->domain_id);
> > + msg->desc_index = cpu_to_le32(desc_index);
> > +}
> > +
> > +static int iter_powercap_cpls_update_state(struct scmi_iterator_state *st,
> > + const void *response, void *priv)
> > +{
> > + const struct scmi_msg_resp_powercap_cpc *r = response;
> > + size_t needed;
> > +
> > + if (st->rx_len < sizeof(r->num_cpl))
> > + return -EPROTO;
> > +
> > + st->num_returned = NUM_RETURNED(r->num_cpl);
> > + st->num_remaining = NUM_REMAINING(r->num_cpl);
> > +
> > + needed = struct_size(r, desc, st->num_returned);
> > + if (st->rx_len < needed)
> > + return -EPROTO;
> > +
> > + return 0;
> > +}
> > +
> > +static int
> > +iter_powercap_cpls_process_response(const struct scmi_protocol_handle *ph,
> > + const void *response,
> > + struct scmi_iterator_state *st, void *priv)
> > +{
> > + const struct scmi_msg_resp_powercap_cpc *r = response;
> > + struct scmi_cpls_priv *p = priv;
> > + struct scmi_powercap_cpl_info *cpl;
> > +
> > + cpl = &p->cpli[st->desc_index + st->loop_idx];
> > +
> > + cpl->id = le32_to_cpu(r->desc[st->loop_idx].cpli);
> > + cpl->cap_config = le32_to_cpu(r->desc[st->loop_idx].flags) & BIT(0);
> > +
> > + cpl->min_power_cap = le32_to_cpu(r->desc[st->loop_idx].min_power_cap);
> > + cpl->max_power_cap = le32_to_cpu(r->desc[st->loop_idx].max_power_cap);
> > + cpl->power_cap_step = le32_to_cpu(r->desc[st->loop_idx].power_cap_step);
> > + if (!cpl->power_cap_step && cpl->min_power_cap != cpl->max_power_cap)
> > + return -EINVAL;
> > +
> > + cpl->min_avg_ivl = le32_to_cpu(r->desc[st->loop_idx].min_cai);
> > + cpl->max_avg_ivl = le32_to_cpu(r->desc[st->loop_idx].max_cai);
> > + cpl->avg_ivl_step = le32_to_cpu(r->desc[st->loop_idx].cai_step);
> > + if (!cpl->avg_ivl_step && cpl->min_avg_ivl != cpl->max_avg_ivl)
> > + return -EINVAL;
> > +
> > + cpl->avg_ivl_config = cpl->min_avg_ivl != cpl->max_avg_ivl;
> > +
> > + strscpy(cpl->name, r->desc[st->loop_idx].name, SCMI_SHORT_NAME_MAX_SIZE);
> > +
> > + return 0;
> > +}
> > +
> > +static int scmi_powercap_cpls_enumerate(const struct scmi_protocol_handle *ph,
> > + struct scmi_powercap_info *dom_info)
> > +{
> > + void *iter;
> > + struct scmi_iterator_ops ops = {
> > + .prepare_message = iter_powercap_cpls_prepare_message,
> > + .update_state = iter_powercap_cpls_update_state,
> > + .process_response = iter_powercap_cpls_process_response,
> > + };
> > + struct scmi_cpls_priv cpriv = {
> > + .domain_id = dom_info->id,
> > + .cpli = dom_info->cpli,
> > + };
> > +
> > + iter = ph->hops->iter_response_init(ph, &ops, dom_info->num_cpli,
> > + POWERCAP_CPC_ATTRIBUTES,
> > + sizeof(struct scmi_msg_powercap_cpc),
> > + &cpriv);
> > + if (IS_ERR(iter))
> > + return PTR_ERR(iter);
> > +
> > + return ph->hops->iter_response_run(iter);
> > +}
> > +
> > +static int
> > +scmi_powercap_domain_attrs_process(const struct scmi_protocol_handle *ph,
> > + struct powercap_info *pinfo,
> > + struct scmi_powercap_info *dom_info, void *r)
> > +{
> > + struct scmi_msg_resp_powercap_domain_attributes *resp = r;
> > + u32 flags = le32_to_cpu(resp->attributes);
> > + bool cap_config;
> > + int ret;
> > +
> > + cap_config = SUPPORTS_POWERCAP_CAP_CONFIGURATION(flags);
> > + if (PROTOCOL_REV_MAJOR(ph->version) < 0x3) {
> > + dom_info->num_cpli = 1;
> > + } else {
> > + dom_info->num_cpli = le32_get_bits(resp->attributes,
> > + GENMASK(18, 15));
> > +
> > + if (cap_config && !dom_info->num_cpli)
> > + return -EINVAL;
> > +
> > + if (!dom_info->num_cpli)
> > + dom_info->num_cpli = 1;
> > + }
> > +
> > + dom_info->cpli = devm_kcalloc(ph->dev, dom_info->num_cpli,
> > + sizeof(*dom_info->cpli), GFP_KERNEL);
> > + if (!dom_info->cpli)
> > + return -ENOMEM;
> > +
> > + if (pinfo->notify_cap_cmd) {
> > + if (PROTOCOL_REV_MAJOR(ph->version) < 0x3)
> > + dom_info->notify_powercap_cap_change =
> > + SUPPORTS_POWERCAP_CAP_CHANGE_NOTIFY(flags);
> > + else
> > + dom_info->notify_powercap_cap_change =
> > + SUPPORTS_POWERCAP_CAP_CHANGE_NOTIFY_V3(flags);
> > + }
> > +
> > + if (pinfo->notify_measurements_cmd)
> > + dom_info->notify_powercap_measurement_change =
> > + SUPPORTS_POWERCAP_MEASUREMENTS_CHANGE_NOTIFY(flags);
> > +
> > + dom_info->extended_names = SUPPORTS_EXTENDED_NAMES(flags);
> > +
> > + dom_info->async_powercap_cap_set =
> > + SUPPORTS_ASYNC_POWERCAP_CAP_SET(flags);
> > +
> > + dom_info->powercap_monitoring =
> > + SUPPORTS_POWERCAP_MONITORING(flags);
> > + dom_info->powercap_scale_mw =
> > + SUPPORTS_POWER_UNITS_MW(flags);
> > + dom_info->powercap_scale_uw =
> > + SUPPORTS_POWER_UNITS_UW(flags);
> > + dom_info->fastchannels =
> > + SUPPORTS_POWERCAP_FASTCHANNELS(flags);
> > +
> > + strscpy(dom_info->name, resp->name, SCMI_SHORT_NAME_MAX_SIZE);
> > +
> > + dom_info->sustainable_power =
> > + le32_to_cpu(resp->sustainable_power);
> > + dom_info->accuracy = le32_to_cpu(resp->accuracy);
> > +
> > + dom_info->parent_id = le32_to_cpu(resp->parent_id);
> > + if (dom_info->parent_id != SCMI_POWERCAP_ROOT_ZONE_ID &&
> > + (dom_info->parent_id >= pinfo->num_domains ||
> > + dom_info->parent_id == dom_info->id)) {
> > + dev_err(ph->dev,
> > + "Platform reported inconsistent parent ID for domain %d - %s\n",
> > + dom_info->id, dom_info->name);
> > + return -ENODEV;
> > + }
> > +
> > + dom_info->cpli[0].id = CPL0;
> > + if (PROTOCOL_REV_MAJOR(ph->version) < 0x3)
> > + dom_info->cpli[0].avg_ivl_config =
> > + SUPPORTS_POWERCAP_PAI_CONFIGURATION(flags);
> > + else
> > + dom_info->cpli[0].avg_ivl_config =
> > + SUPPORTS_POWERCAP_CAI_CONFIGURATION(flags);
> > +
> > + if (PROTOCOL_REV_MAJOR(ph->version) < 0x3) {
> > + dom_info->cpli[0].min_avg_ivl = le32_to_cpu(resp->min_pai);
> > + dom_info->cpli[0].max_avg_ivl = le32_to_cpu(resp->max_pai);
> > + dom_info->cpli[0].avg_ivl_step = le32_to_cpu(resp->pai_step);
> > + } else {
> > + struct scmi_msg_resp_powercap_domain_attributes_v3 *resp = r;
> > +
> > + dom_info->cpli[0].min_avg_ivl = le32_to_cpu(resp->min_cai);
> > + dom_info->cpli[0].max_avg_ivl = le32_to_cpu(resp->max_cai);
> > + dom_info->cpli[0].avg_ivl_step = le32_to_cpu(resp->cai_step);
> > + }
> > +
> > + ret = scmi_powercap_validate(dom_info->cpli[0].min_avg_ivl,
> > + dom_info->cpli[0].max_avg_ivl,
> > + dom_info->cpli[0].avg_ivl_step,
> > + dom_info->cpli[0].avg_ivl_config);
>
> This could be existing bug w.r.t conformance as we are supposed to allow
> 0 as valid CAI and MAI values. It may need fixing with current PAI handling
> and we need to avoid using the same check on CAI.
>
> The spec states: "The platform may choose not to report CAI or MAI".
>
> Please take a look and fix the existing bug and the one in this series
> that applies for CAI.
>
> I am just looking at conformance for now.
>
Okay, I will look at this. Thank you.
Regards,
Phil
next prev parent reply other threads:[~2026-10-15 13:15 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-09 22:04 [PATCH v9 00/13] Add support for SCMIv4.0 Powercap Extensions Philip Radford
2026-09-09 22:04 ` [PATCH v9 01/13] powercap: Add enable disable control-type Philip Radford
2026-09-09 22:04 ` [PATCH v9 02/13] firmware: arm_scmi: Add an optional custom parameter to fastchannel helpers Philip Radford
2026-09-09 22:04 ` [PATCH v9 03/13] firmware: arm_scmi: Refactor powercap domain layout Philip Radford
2026-09-09 22:04 ` [PATCH v9 04/13] firmware: arm_scmi: Add SCMIv4.0 Powercap basic support Philip Radford
2026-10-15 12:57 ` Sudeep Holla
2026-10-15 13:15 ` Philip Radford [this message]
2026-09-09 22:04 ` [PATCH v9 05/13] firmware: arm_scmi: Add SCMIv4.0 Powercap FCs support Philip Radford
2026-09-09 22:04 ` [PATCH v9 06/13] firmware: arm_scmi: Add SCMIV4.0 Powercap notifications support Philip Radford
2026-09-09 22:04 ` [PATCH v9 07/13] firmware: arm_scmi: Extend powercap report to include MAI Philip Radford
2026-09-09 22:04 ` [PATCH v9 08/13] include: trace: Add new parameter to trace_scmi_fc_call Philip Radford
2026-09-09 22:04 ` [PATCH v9 09/13] powercap: arm_scmi: Enable multiple constraints support Philip Radford
2026-10-15 13:24 ` Sudeep Holla
2026-10-15 14:32 ` Philip Radford
2026-09-09 22:04 ` [PATCH v9 10/13] firmware: arm_scmi: add Powercap MAI get/set support Philip Radford
2026-09-09 22:04 ` [PATCH v9 11/13] powercap: arm_scmi: Create synthetic parent node for multi-instance Philip Radford
2026-09-09 22:04 ` [PATCH v9 12/13] powercap: arm_scmi: Add get_power_uw to synthetic node Philip Radford
2026-09-09 22:04 ` [PATCH v9 13/13] powercap: arm_scmi: Synthetic zone enable/disable Philip Radford
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=atDPwqwoYWqeFKdJ@e121740.arm.com \
--to=philip.radford@arm.com \
--cc=arm-scmi@vger.kernel.org \
--cc=cristian.marussi@arm.com \
--cc=d-gole@ti.com \
--cc=dan.carpenter@linaro.org \
--cc=etienne.carriere@st.com \
--cc=f.fainelli@gmail.com \
--cc=james.quinlan@broadcom.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=michal.simek@amd.com \
--cc=peng.fan@oss.nxp.com \
--cc=quic_sibis@quicinc.com \
--cc=souvik.chakravarty@arm.com \
--cc=sudeep.holla@kernel.org \
--cc=vincent.guittot@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox