* 2.6.6 kernel, active-filter completely stops idle reset
@ 2004-06-27 21:46 Clifford Kite
2004-07-26 23:26 ` 2.6.6 kernel, active-filter completely stops idle reset (repost) Clifford Kite
2004-07-28 21:45 ` Arvin Schnell
0 siblings, 2 replies; 3+ messages in thread
From: Clifford Kite @ 2004-06-27 21:46 UTC (permalink / raw)
To: linux-ppp
Background
----------
2.6.6 kernel compiled from a standard kernel.org source package with
"make oldconfig" and the .config of a 2.6.4 kernel (also compiled here
from a kernel.org source package).
Pppd 2.4.2 compiled from a standard samba.org source package. It has been
patched to correct a bug, and to correctly reset the terminal line settings
in most instances.
Regular PPP landline connection.
----------
The active-filter configuration is
active-filter '(outbound and not (icmp[0] = 0))'
and is used with the "idle 300" option. This should prevent any inbound
traffic or outbound ping replies from resetting the idle timer, while
allowing outbound traffic, other than a ping reply, to reset it. Which
it does with the 2.6.4 kernel, and with 2.4.x kernels as well.
With the 2.4.6 kernel the PPP link comes down after 300 seconds regardless
of the activity on the link. E.g., "ping -i 280 192.168.5.33" doesn't keep
the link up, but it also seems to be true for any other type of activity,
incoming or outgoing. The idle timer is apparently not reset. A link that
is brought up without the active-filter option behaves normally, both with
and without the idle option.
I looked briefly through the Changes at kernel.org but didn't see anything
directly related to PPP that sounded like it might cause this. Even so, it
seems to me rather unlikely that it is the result of something I did wrong,
or have not done but need to do.
Any feedback? Or is this list dead? It's been a long time since I've
received any email from it.
---
Clifford Kite http://ckite.no-ip.net
^ permalink raw reply [flat|nested] 3+ messages in thread
* 2.6.6 kernel, active-filter completely stops idle reset (repost)
2004-06-27 21:46 2.6.6 kernel, active-filter completely stops idle reset Clifford Kite
@ 2004-07-26 23:26 ` Clifford Kite
2004-07-28 21:45 ` Arvin Schnell
1 sibling, 0 replies; 3+ messages in thread
From: Clifford Kite @ 2004-07-26 23:26 UTC (permalink / raw)
To: linux-ppp
Below is a copy of an email sent to this mailing list on June 27, 2004,
to which there has been no reply. So here it is again. If anyone
knows why the pppd active-filter option broke under the 2.6.6 kernel
then *please* respond. If anyone even knows of a part of the kernel,
aside from PPP support, that might cause the problem then please respond.
Apparently the list is not entirely dead since I received an inquiry
today, from someone that read the post, as to whether I had found out
what was wrong. He said it's still broken in the 2.6.7 kernel (the
latest at the time of this writing).
TIA
---
Clifford Kite http://ckite.no-ip.net
---------- Forwarded message ----------
Date: Sun, 27 Jun 2004 16:46:48 -0500 (CDT)
From: Clifford Kite <kite_linux-ppp@ev1.net>
To: linux-ppp@vger.kernel.org
Subject: 2.6.6 kernel, active-filter completely stops idle reset
Background
----------
2.6.6 kernel compiled from a standard kernel.org source package with
"make oldconfig" and the .config of a 2.6.4 kernel (also compiled here
from a kernel.org source package).
Pppd 2.4.2 compiled from a standard samba.org source package. It has been
patched to correct a bug, and to correctly reset the terminal line settings
in most instances.
Regular PPP landline connection.
----------
The active-filter configuration is
active-filter '(outbound and not (icmp[0] = 0))'
and is used with the "idle 300" option. This should prevent any inbound
traffic or outbound ping replies from resetting the idle timer, while
allowing outbound traffic, other than a ping reply, to reset it. Which
it does with the 2.6.4 kernel, and with 2.4.x kernels as well.
With the 2.4.6 kernel the PPP link comes down after 300 seconds regardless
of the activity on the link. E.g., "ping -i 280 192.168.5.33" doesn't keep
the link up, but it also seems to be true for any other type of activity,
incoming or outgoing. The idle timer is apparently not reset. A link that
is brought up without the active-filter option behaves normally, both with
and without the idle option.
I looked briefly through the Changes at kernel.org but didn't see anything
directly related to PPP that sounded like it might cause this. Even so, it
seems to me rather unlikely that it is the result of something I did wrong,
or have not done but need to do.
Any feedback? Or is this list dead? It's been a long time since I've
received any email from it.
---
Clifford Kite http://ckite.no-ip.net
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: 2.6.6 kernel, active-filter completely stops idle reset (repost)
2004-06-27 21:46 2.6.6 kernel, active-filter completely stops idle reset Clifford Kite
2004-07-26 23:26 ` 2.6.6 kernel, active-filter completely stops idle reset (repost) Clifford Kite
@ 2004-07-28 21:45 ` Arvin Schnell
1 sibling, 0 replies; 3+ messages in thread
From: Arvin Schnell @ 2004-07-28 21:45 UTC (permalink / raw)
To: linux-ppp
[-- Attachment #1: Type: text/plain, Size: 1651 bytes --]
On Mon, Jul 26, 2004 at 06:26:37PM -0500, Clifford Kite wrote:
> Below is a copy of an email sent to this mailing list on June 27, 2004,
> to which there has been no reply. So here it is again. If anyone
> knows why the pppd active-filter option broke under the 2.6.6 kernel
> then *please* respond. If anyone even knows of a part of the kernel,
> aside from PPP support, that might cause the problem then please respond.
Hi,
at SUSE we had problems with the idle time (and still do have at
least one bug) and kernel 2.6.5. But I myself don't know all the
details, esp. not on the kernel side.
The first problem was due to a update of libpcap to version
0.8.1. The pppd uses an internal header file of libpcap. I have
fixed that and sent a patch to this mailing list.
IIRC with the new libpcap the "inbound" and "outbound" keywords
did not work any longer. The libpcap authors told us to use
DLT_LINUX_SLL instead of DLT_PPP since the latter is really
buggy.
So we changed that but still some things didn't work,
e.g. traffic wouldn't bring up a dial on demand connection and
the idle time was broken. This was (partly?) due to the fact
that DLT_LINUX_SLL assume a 16 byte faked ethernet header on each
packet.
Well, attached are two patches, one for the pppd and one for the
kernel. I think that are all patches we have concerning that
problem. Some parts of them aren't nice, esp. with that 16 bytes
fake header. Maybe they are of help to you anyway.
ciao Arvin
PS: Since I'm on vacation I will only read mail on a very
irregular basis.
--
Dipl.-Phys. Arvin Schnell
SUSE Linux AG
Research & Development
email: arvin@suse.de
[-- Attachment #2: ppp-2.4.2-libpcap.diff --]
[-- Type: text/plain, Size: 4294 bytes --]
--- pppd/demand.c
+++ pppd/demand.c
@@ -50,8 +50,9 @@
#include <sys/socket.h>
#ifdef PPP_FILTER
#include <net/if.h>
-#include <net/bpf.h>
+#include <pcap-bpf.h>
#include <pcap.h>
+#include <linux/if_ether.h>
#endif
#include "pppd.h"
@@ -61,6 +62,10 @@
static const char rcsid[] = RCSID;
+#ifdef PPP_FILTER
+static char *___frame;
+#endif
+
char *frame;
int framelen;
int framemax;
@@ -92,7 +97,13 @@
if (framemax < PPP_MRU) */
framemax = PPP_MRU;
framemax += PPP_HDRLEN + PPP_FCSLEN;
+#ifdef PPP_FILTER
+ /* for DLT_LINUX_SLL we need to build a 16 byte fake header */
+ ___frame = malloc(framemax + 16);
+ frame = ___frame + 16;
+#else
frame = malloc(framemax);
+#endif
if (frame == NULL)
novm("demand frame");
framelen = 0;
@@ -348,12 +359,43 @@
return 0;
proto = PPP_PROTOCOL(p);
#ifdef PPP_FILTER
- if (pass_filter.bf_len != 0
- && bpf_filter(pass_filter.bf_insns, p, len, len) == 0)
- return 0;
- if (active_filter.bf_len != 0
- && bpf_filter(active_filter.bf_insns, p, len, len) == 0)
- return 0;
+ if (active_filter.bf_len || pass_filter.bf_len) {
+ /* for DLT_LINUX_SLL we need to build a 16 byte fake header
+ * first word direction flag, last word ETHERNET protocol type
+ * current header is only 4 bytes
+ */
+ u_int32_t sav;
+ u_int16_t ethp;
+
+ switch(proto) {
+ case PPP_IP:
+ ethp = ETH_P_IP;
+ break;
+ case PPP_IPX:
+ ethp = ETH_P_IPX;
+ break;
+ case PPP_IPV6:
+ ethp = ETH_P_IPV6;
+ break;
+ default:
+ goto unhandled_proto;
+ }
+ /* save current header value */
+ sav = *(u_int32_t *)p;
+ *(u_int16_t *)(p+2) = htons(ethp);
+ p -= 12;
+ /* outgoing in DLT_LINUX_SLL */
+ *(u_int16_t *)p = htons(4);
+ if (pass_filter.bf_len != 0
+ && bpf_filter(pass_filter.bf_insns, p, len, len) == 0)
+ return 0;
+ if (active_filter.bf_len != 0
+ && bpf_filter(active_filter.bf_insns, p, len, len) == 0)
+ return 0;
+ p += 12;
+ *(u_int32_t *)p = sav;
+ }
+unhandled_proto:
#endif
for (i = 0; (protp = protocols[i]) != NULL; ++i) {
if (protp->protocol < 0xC000 && (protp->protocol & ~0x8000) == proto) {
--- pppd/sys-linux.c
+++ pppd/sys-linux.c
@@ -85,7 +85,7 @@
#endif /* IPX_CHANGE */
#ifdef PPP_FILTER
-#include <net/bpf.h>
+#include <pcap-bpf.h>
#include <linux/filter.h>
#endif /* PPP_FILTER */
--- ./pppd/options.c.orig 2004-02-18 15:42:37.366603970 +0000
+++ ./pppd/options.c 2004-02-18 15:44:01.243247770 +0000
@@ -56,7 +56,6 @@
#endif
#ifdef PPP_FILTER
#include <pcap.h>
-#include <pcap-int.h> /* XXX: To get struct pcap */
#endif
#include "pppd.h"
@@ -122,7 +121,6 @@
#ifdef PPP_FILTER
struct bpf_program pass_filter;/* Filter program for packets to pass */
struct bpf_program active_filter; /* Filter program for link-active pkts */
-pcap_t pc; /* Fake struct pcap so we can compile expr */
#endif
char *current_option; /* the name of the option being parsed */
@@ -1439,12 +1437,20 @@
setpassfilter(argv)
char **argv;
{
- pc.linktype = DLT_PPP;
- pc.snapshot = PPP_HDRLEN;
+ pcap_t* pc = pcap_open_dead (DLT_LINUX_SLL, PPP_HDRLEN);
- if (pcap_compile(&pc, &pass_filter, *argv, 1, netmask) == 0)
+ if (!pc) {
+ option_error("error in pass-filter expression: pcap_open_dead failed\n");
+ return 0;
+ }
+
+ if (pcap_compile(pc, &pass_filter, *argv, 1, netmask) == 0) {
+ pcap_close (pc);
return 1;
- option_error("error in pass-filter expression: %s\n", pcap_geterr(&pc));
+ }
+
+ option_error("error in pass-filter expression: %s\n", pcap_geterr(pc));
+ pcap_close (pc);
return 0;
}
@@ -1455,12 +1461,20 @@
setactivefilter(argv)
char **argv;
{
- pc.linktype = DLT_PPP;
- pc.snapshot = PPP_HDRLEN;
+ pcap_t* pc = pcap_open_dead (DLT_LINUX_SLL, PPP_HDRLEN);
- if (pcap_compile(&pc, &active_filter, *argv, 1, netmask) == 0)
+ if (!pc) {
+ option_error("error in active-filter expression: pcap_open_dead failed\n");
+ return 0;
+ }
+
+ if (pcap_compile(pc, &active_filter, *argv, 1, netmask) == 0) {
+ pcap_close (pc);
return 1;
- option_error("error in active-filter expression: %s\n", pcap_geterr(&pc));
+ }
+
+ option_error("error in active-filter expression: %s\n", pcap_geterr(pc));
+ pcap_close (pc);
return 0;
}
#endif
[-- Attachment #3: ppp-filter-fix --]
[-- Type: text/plain, Size: 12227 bytes --]
diff -ur linux-2.6.5-7.61cvs20040528072728.org/drivers/isdn/i4l/Kconfig linux/drivers/isdn/i4l/Kconfig
--- linux-2.6.5-7.61cvs20040528072728.org/drivers/isdn/i4l/Kconfig 2004-05-31 23:52:23.438980163 +0200
+++ linux/drivers/isdn/i4l/Kconfig 2004-05-28 13:10:10.000000000 +0200
@@ -31,6 +31,17 @@
by bundling several ISDN-connections, using this protocol. See
<file:Documentation/isdn/README.syncppp> for more information.
+config IPPP_FILTER
+ bool "Filtering for synchronous PPP"
+ depends on ISDN_PPP
+ help
+ Say Y here if you want to be able to filter the packets passing over
+ IPPP interfaces. This allows you to control which packets count as
+ activity (i.e. which packets will reset the idle timer or bring up
+ a demand-dialled link) and which packets are to be dropped entirely.
+ You need to say Y here if you wish to use the pass-filter and
+ active-filter options to ipppd.
+
config ISDN_PPP_BSDCOMP
tristate "Support BSD compression"
depends on ISDN_PPP
diff -ur linux-2.6.5-7.61cvs20040528072728.org/drivers/isdn/i4l/isdn_ppp.c linux/drivers/isdn/i4l/isdn_ppp.c
--- linux-2.6.5-7.61cvs20040528072728.org/drivers/isdn/i4l/isdn_ppp.c 2004-05-31 23:52:23.461977141 +0200
+++ linux/drivers/isdn/i4l/isdn_ppp.c 2004-05-29 00:01:48.099568121 +0200
@@ -606,7 +606,7 @@
if (copy_from_user(&uprog, (void *) arg, sizeof(uprog)))
return -EFAULT;
- if (uprog.len > 0 && uprog.len < 65536) {
+ if (uprog.len > 0) {
len = uprog.len * sizeof(struct sock_filter);
code = kmalloc(len, GFP_KERNEL);
if (code == NULL)
@@ -1117,30 +1117,36 @@
}
#ifdef CONFIG_IPPP_FILTER
- /* check if the packet passes the pass and active filters
- * the filter instructions are constructed assuming
- * a four-byte PPP header on each packet (which is still present) */
- skb_push(skb, 4);
- skb->data[0] = 0; /* indicate inbound */
-
- if (is->pass_filter.filter
- && sk_run_filter(skb, is->pass_filter.filter,
- is->pass_filter.len) == 0) {
+ /* the DLT_LINUX_SLL filter instructions are constructed assuming
+ * a 16 byte faked ethernet header on each packet first word
+ * is the direction flag the last contain the ethernet protocol
+ * so we need 16 byte headroom, which should be always available
+ * to avoid underrun abort filtering if here is no room
+ */
+ if (unlikely(skb_headroom(skb) < 16)) {
+ printk(KERN_WARNING "ppp filters (in) not running - need %d byte more headroom\n",
+ 16 - skb_headroom(skb));
+ goto no_filter;
+ }
+ *(u_int16_t *)skb_push(skb, 2) = skb->protocol;
+ *(u_int16_t *)skb_push(skb, 14) = 0; /* indicate inbound in DLT_LINUX_SLL */
+ if (is->pass_filter.filter &&
+ sk_run_filter(skb, is->pass_filter.filter, is->pass_filter.len) == 0) {
if (is->debug & 0x2)
printk(KERN_DEBUG "IPPP: inbound frame filtered.\n");
kfree_skb(skb);
return;
}
- if (!(is->active_filter.filter
- && sk_run_filter(skb, is->active_filter.filter,
- is->active_filter.len) == 0)) {
+ if (!(is->active_filter.filter &&
+ sk_run_filter(skb, is->active_filter.filter, is->active_filter.len) == 0)) {
if (is->debug & 0x2)
printk(KERN_DEBUG "IPPP: link-active filter: reseting huptimer.\n");
lp->huptimer = 0;
if (mlp)
mlp->huptimer = 0;
}
- skb_pull(skb, 4);
+ skb_pull(skb, 16);
+no_filter:
#else /* CONFIG_IPPP_FILTER */
lp->huptimer = 0;
if (mlp)
@@ -1259,29 +1265,34 @@
skb_pull(skb,IPPP_MAX_HEADER);
#ifdef CONFIG_IPPP_FILTER
- /* check if we should pass this packet
- * the filter instructions are constructed assuming
- * a four-byte PPP header on each packet */
- skb_push(skb, 4);
- skb->data[0] = 1; /* indicate outbound */
- *(u_int16_t *)(skb->data + 2) = htons(proto);
-
- if (ipt->pass_filter.filter
- && sk_run_filter(skb, ipt->pass_filter.filter,
- ipt->pass_filter.len) == 0) {
+ /* the DLT_LINUX_SLL filter instructions are constructed assuming
+ * a 16 byte faked ethernet header on each packet first word
+ * is the direction flag the last contain the ethernet protocol
+ * so we need 16 byte headroom, which _should_ be always available
+ * to avoid underrun abort filtering if here is unlikely no room
+ */
+ if (unlikely(skb_headroom(skb) < 16)) {
+ printk(KERN_WARNING "ppp filters(out) not running - need %d byte more headroom\n",
+ 16 - skb_headroom(skb));
+ goto no_filter;
+ }
+ *(u_int16_t *)skb_push(skb, 2) = skb->protocol;
+ *(u_int16_t *)skb_push(skb, 14) = htons(4); /* indicate outbound in DLT_LINUX_SLL */
+ if (ipt->pass_filter.filter &&
+ sk_run_filter(skb, ipt->pass_filter.filter, ipt->pass_filter.len) == 0) {
if (ipt->debug & 0x4)
printk(KERN_DEBUG "IPPP: outbound frame filtered.\n");
kfree_skb(skb);
goto unlock;
}
- if (!(ipt->active_filter.filter
- && sk_run_filter(skb, ipt->active_filter.filter,
- ipt->active_filter.len) == 0)) {
+ if (!(ipt->active_filter.filter &&
+ sk_run_filter(skb, ipt->active_filter.filter, ipt->active_filter.len) == 0)) {
if (ipt->debug & 0x4)
printk(KERN_DEBUG "IPPP: link-active filter: reseting huptimer.\n");
lp->huptimer = 0;
}
- skb_pull(skb, 4);
+ skb_pull(skb, 16);
+no_filter:
#else /* CONFIG_IPPP_FILTER */
lp->huptimer = 0;
#endif /* CONFIG_IPPP_FILTER */
@@ -1435,15 +1446,12 @@
int isdn_ppp_autodial_filter(struct sk_buff *skb, isdn_net_local *lp)
{
struct ippp_struct *is = ippp_table[lp->ppp_slot];
- u_int16_t proto;
int drop = 0;
+ u_int16_t savprot;
switch (ntohs(skb->protocol)) {
case ETH_P_IP:
- proto = PPP_IP;
- break;
case ETH_P_IPX:
- proto = PPP_IPX;
break;
default:
printk(KERN_ERR "isdn_ppp_autodial_filter: unsupported protocol 0x%x.\n",
@@ -1451,14 +1459,22 @@
return 1;
}
- /* the filter instructions are constructed assuming
- * a four-byte PPP header on each packet. we have to
- * temporarily remove part of the fake header stuck on
- * earlier.
+ /* the DLT_LINUX_SLL filter instructions are constructed assuming
+ * a 16 byte faked ethernet header on each packet first word
+ * is the direction flag the last contain the ethernet protocol
+ * so we need 16 - IPPP_MAX_HEADER byte extra headroom, which
+ * _should_ be always available to avoid underrun abort filtering
+ * if here is unlikely no room
*/
- skb_pull(skb, IPPP_MAX_HEADER - 4);
- skb->data[0] = 1; /* indicate outbound */
- *(u_int16_t *)(skb->data + 2) = htons(proto);
+ if (unlikely(skb_headroom(skb) < 16 - IPPP_MAX_HEADER)) {
+ printk(KERN_WARNING "ppp filters(autodial) not running - need %d byte more headroom\n",
+ 16 - IPPP_MAX_HEADER - skb_headroom(skb));
+ return 0;
+ }
+ skb_pull(skb, IPPP_MAX_HEADER - 2);
+ savprot = *(u_int16_t *)skb->data;
+ *(u_int16_t *)skb->data = skb->protocol;
+ *(u_int16_t *)skb_push(skb, 14) = htons(4); /* indicate outbound in DLT_LINUX_SLL */
drop |= is->pass_filter.filter
&& sk_run_filter(skb, is->pass_filter.filter,
@@ -1467,7 +1483,9 @@
&& sk_run_filter(skb, is->active_filter.filter,
is->active_filter.len) == 0;
- skb_push(skb, IPPP_MAX_HEADER - 4);
+ skb_pull(skb, 14);
+ *(u_int16_t *)skb->data = savprot;
+ skb_push(skb, IPPP_MAX_HEADER - 2);
return drop;
}
#endif
diff -ur linux-2.6.5-7.61cvs20040528072728.org/drivers/net/ppp_generic.c linux/drivers/net/ppp_generic.c
--- linux-2.6.5-7.61cvs20040528072728.org/drivers/net/ppp_generic.c 2004-05-31 23:52:23.494972805 +0200
+++ linux/drivers/net/ppp_generic.c 2004-05-29 00:01:54.953663457 +0200
@@ -991,29 +991,49 @@
if (proto < 0x8000) {
#ifdef CONFIG_PPP_FILTER
- /* check if we should pass this packet */
- /* the filter instructions are constructed assuming
- a four-byte PPP header on each packet */
- *skb_push(skb, 2) = 1;
- if (ppp->pass_filter.filter
- && sk_run_filter(skb, ppp->pass_filter.filter,
- ppp->pass_filter.len) == 0) {
- if (ppp->debug & 1)
- printk(KERN_DEBUG "PPP: outbound frame not passed\n");
- kfree_skb(skb);
- return;
+ /* the DLT_LINUX_SLL filter instructions are constructed assuming
+ * a 16 byte faked ethernet header on each packet first word
+ * is the direction flag the last contain the ethernet protocol
+ */
+ if (ppp->pass_filter.filter || ppp->active_filter.filter) {
+ int npi = proto_to_npindex(proto);
+
+ if (npi < 0) /* we only filter defined protocols */
+ goto no_filter;
+
+ /* we only have a 2 byte header yet so we need 14 bytes more headroom
+ * to avoid underrun abort filtering if here is no room
+ */
+ if (unlikely(skb_headroom(skb) < 14)) {
+ printk(KERN_WARNING "ppp filters (out) not running - need %d byte more headroom\n",
+ 14 - skb_headroom(skb));
+ goto no_filter;
+ }
+ /* we set the ethernet protocol in the header */
+ *(u_int16_t *)skb->data = htons(npindex_to_ethertype[npi]);
+ *(u_int16_t *)skb_push(skb, 14) = htons(4); /* indicate outbound in DLT_LINUX_SLL */
+ /* check if we should pass this packet */
+ if (ppp->pass_filter.filter &&
+ sk_run_filter(skb, ppp->pass_filter.filter, ppp->pass_filter.len) == 0) {
+ if (ppp->debug & 1)
+ printk(KERN_DEBUG "PPP: outbound frame not passed\n");
+ kfree_skb(skb);
+ return;
+ }
+ /* if this packet passes the active filter, record the time */
+ if (!(ppp->active_filter.filter &&
+ sk_run_filter(skb, ppp->active_filter.filter, ppp->active_filter.len) == 0))
+ ppp->last_xmit = jiffies;
+ skb_pull(skb, 14);
+ *(u_int16_t *)skb->data = htons(proto); /* rewrite PPP protocol value */
}
- /* if this packet passes the active filter, record the time */
- if (!(ppp->active_filter.filter
- && sk_run_filter(skb, ppp->active_filter.filter,
- ppp->active_filter.len) == 0))
- ppp->last_xmit = jiffies;
- skb_pull(skb, 2);
+ }
+no_filter:
#else
/* for data packets, record the time */
ppp->last_xmit = jiffies;
-#endif /* CONFIG_PPP_FILTER */
}
+#endif /* CONFIG_PPP_FILTER */
++ppp->stats.tx_packets;
ppp->stats.tx_bytes += skb->len - 2;
@@ -1553,23 +1573,37 @@
/* network protocol frame - give it to the kernel */
#ifdef CONFIG_PPP_FILTER
- /* check if the packet passes the pass and active filters */
- /* the filter instructions are constructed assuming
- a four-byte PPP header on each packet */
- *skb_push(skb, 2) = 0;
- if (ppp->pass_filter.filter
- && sk_run_filter(skb, ppp->pass_filter.filter,
- ppp->pass_filter.len) == 0) {
- if (ppp->debug & 1)
- printk(KERN_DEBUG "PPP: inbound frame not passed\n");
- kfree_skb(skb);
- return;
+ /* the DLT_LINUX_SLL filter instructions are constructed assuming
+ * a 16 byte faked ethernet header on each packet first word
+ * is the direction flag the last contain the ethernet protocol
+ */
+ if (ppp->pass_filter.filter || ppp->active_filter.filter) {
+ /* we only have a 2 byte header yet so we need 14 bytes more headroom
+ * to avoid underrun abort filtering if here is no room
+ */
+ if (unlikely(skb_headroom(skb) < 14)) {
+ printk(KERN_WARNING "ppp filters (in) not running - need %d byte more headroom\n",
+ 14 - skb_headroom(skb));
+ goto no_filter;
+ }
+ /* we set the ethernet protocol in the header */
+ *(u_int16_t *)skb->data = htons(npindex_to_ethertype[npi]);
+ *(u_int16_t *)skb_push(skb, 14) = 0; /* indicate inbound in DLT_LINUX_SLL */
+ /* check if we should pass this packet */
+ if (ppp->pass_filter.filter &&
+ sk_run_filter(skb, ppp->pass_filter.filter, ppp->pass_filter.len) == 0) {
+ if (ppp->debug & 1)
+ printk(KERN_DEBUG "PPP: inbound frame not passed\n");
+ kfree_skb(skb);
+ return;
+ }
+ if (!(ppp->active_filter.filter &&
+ sk_run_filter(skb, ppp->active_filter.filter, ppp->active_filter.len) == 0))
+ ppp->last_recv = jiffies;
+ skb_pull(skb, 14);
+ /* we do not need to restore the old protocol value it is pulled next step */
}
- if (!(ppp->active_filter.filter
- && sk_run_filter(skb, ppp->active_filter.filter,
- ppp->active_filter.len) == 0))
- ppp->last_recv = jiffies;
- skb_pull(skb, 2);
+no_filter:
#else
ppp->last_recv = jiffies;
#endif /* CONFIG_PPP_FILTER */
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2004-07-28 21:45 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-06-27 21:46 2.6.6 kernel, active-filter completely stops idle reset Clifford Kite
2004-07-26 23:26 ` 2.6.6 kernel, active-filter completely stops idle reset (repost) Clifford Kite
2004-07-28 21:45 ` Arvin Schnell
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).