SATA ontrollers and Linux MD

SATA ontrollers and Linux MD

[Ruth Ivimey-Cook]

 Hi,

I've a file server running on an Athlon XP 3200+ motherboard, currently using a
mixture of PATA and SATA-150 drives and Fedora Core 5 Linux. 5x 120GB Seagate
drives form a single raid-5 volume. One of those drives has failed, the rest
are old, and I'm looking to replace all of them. I'd appreciate any help
selecting components!

The motherboard uses a KT600 chipset and so includes two SATA-150 connections
serving 2 of the Raid-5 disks. The rest of the Raid-5 is currently run off a 2
channel Highpoint PATA PCI controller.

Currently, I'm looking at buying 5 Samsung P120 series drives - the 250GB
SATA-300 "SP2504C". To reduce cost I might possibly use 4 rather than 5, or
might go for the 160GB variant. Reason for these drives is I've found them
quiet, and reasonably fast & cool - all important to me. I don't need
cutting-edge performance, but reliability is good!

Controller-wise, finding suitable SATA-300 controllers is hard. Requirements
include at least 4 internal ports and a PCI not PCIe interface. I might end up
with a SATA-150 controller and upgrade it and the MB sometime later. I'm not
really after a dedicated RAID controller such as the 3ware ones, as (a) I can't
really justify the cost and (b) I want to use Linux MD for reasons of
portability.

Aside: Over PCI, is it better to use two separate 2-channel PCI cards or one
4-channel card? For example, 2x Sil 3112 chips or 1x Sil 3114, given that
you're using all disks in JBOD mode?

I'm very tempted by the Sil 3124 controller, although I've not had much luck
finding a PCI version of it. In the States there's a company "SATACard" who
appear to make one that's suitable, but I can't find a UK supplier. Scan are
selling the Supermicro 8 Port SATA 2 RAID Card AOC-SAT2-MV8, but with not much
info other than it's based on the Marvell Hercules-2 Rev. C0 SATA host
controller. Others that include the various Promise and Highpoint controllers,
but my experience of Promise QA is not good, and Highpoint SATA-300 seems to
use Infiniband, for which Linux support looks really cutting edge. I don't want
to use proprietary drivers and I'd much prefer something FC5 supports natively.

Any thoughts?

Thanks,

Ruth

Re: SATA ontrollers and Linux MD

[Alex Davis]

I'm currently using a Promise Technologies TX4300 SATA II 3.0GB/s controller, to which are
connected 4 Seagate Barracuda 7200.10 ST3320620AS 320GB drives. I've only had this setup for 
2 weeks but so far I'm happy with it. The controller is PCI and costs about $66. the drives 
are about $100/each.

Note: the cables that come with the controller come loose too easy. If you go this route,
get some additional cables.

I have a RAID5 setup. While sync'ing, the throughput was about 30MB/sec.



I code, therefore I am

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 

Re: SATA ontrollers and Linux MD

[Lem]

On Wed, 2006-08-30 at 20:31 -0700, Alex Davis wrote:
> I'm currently using a Promise Technologies TX4300 SATA II 3.0GB/s controller, to which are
> connected 4 Seagate Barracuda 7200.10 ST3320620AS 320GB drives. I've only had this setup for 
> 2 weeks but so far I'm happy with it. The controller is PCI and costs about $66. the drives 
> are about $100/each.

I too have this controller card. I was looking for a cheap SATA card
which had Linux support that I could use with software RAID. It seems to
work fine.

> Note: the cables that come with the controller come loose too easy. If you go this route,
> get some additional cables.
> 
> I have a RAID5 setup. While sync'ing, the throughput was about 30MB/sec.

I have a RAID5 setup also. 5x256GB Seagate SATA drives (some are the
newer NCQ ones, some are older ones). Only two are on the Promise card,
the other three are on the motherboard nVidia (nForce3 CK8S) and Silicon
Image (SiI 3512) controllers. Sync speed is about the same for me
(regardless of trying to change the minimum via /proc).

I have an Audigy 2 ZS on the same PCI bus as the Promise card, and when
I write to the RAID array, I get a lot of pops, clicks, glitches,
squeaks etc through the sound (only when I'm outputting audio to the
soundcard simultaneously). Reads don't produce the same thing, in fact
reads don't interfere with audio at all. Do you have a soundcard on your
PCI bus, and if so, have you experienced this?

RE: SATA ontrollers and Linux MD

[Ruth Ivimey-Cook]

Folks, 

> I'm currently using a Promise Technologies TX4300 SATA II 
> 3.0GB/s controller, to which are connected 4 Seagate 
> Barracuda 7200.10 ST3320620AS 320GB drives. I've only had 
> this setup for
> 2 weeks but so far I'm happy with it. The controller is PCI 
> and costs about $66. the drives are about $100/each.

Thanks. Someone else mentioned the TX4 as being ok.

I'm also more seriously considering the Supermicro SAT2

Thanks for your thoughts.

Ruth

Re: SATA ontrollers and Linux MD

[Alex Davis]

--- Lem <l3mming@iinet.net.au> wrote:

> I have an Audigy 2 ZS on the same PCI bus as the Promise card, and when
> I write to the RAID array, I get a lot of pops, clicks, glitches,
> squeaks etc through the sound (only when I'm outputting audio to the
> soundcard simultaneously). Reads don't produce the same thing, in fact
> reads don't interfere with audio at all. Do you have a soundcard on your
> PCI bus, and if so, have you experienced this?
I have a creative PCI soundcard, and hear no popping and clicking; under really
heavy I/O (multiple writers) I get pauses, but that's probably to be expected.
> 
> 


I code, therefore I am

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com