From: NeilBrown <neilb@suse.de>
To: Andrew Morton <akpm@osdl.org>
Cc: linux-raid@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH 009 of 10] md: Allow resync_start to be set and queried via sysfs.
Date: Thu, 1 Jun 2006 15:14:13 +1000 [thread overview]
Message-ID: <1060601051413.27649@suse.de> (raw)
In-Reply-To: 20060601150955.27444.patches@notabene
Signed-off-by: Neil Brown <neilb@suse.de>
### Diffstat output
./Documentation/md.txt | 6 ++++++
./drivers/md/md.c | 26 ++++++++++++++++++++++++++
2 files changed, 32 insertions(+)
diff ./Documentation/md.txt~current~ ./Documentation/md.txt
--- ./Documentation/md.txt~current~ 2006-06-01 15:05:30.000000000 +1000
+++ ./Documentation/md.txt 2006-06-01 15:05:30.000000000 +1000
@@ -205,6 +205,12 @@ All md devices contain:
simply a number that is interpretted differently by different
levels. It can be written while assembling an array.
+ resync_start
+ The point at which resync should start. If no resync is needed,
+ this will be a very large number. At array creation it will
+ default to 0, though starting the array as 'clean' will
+ set it much larger.
+
new_dev
This file can be written but not read. The value written should
be a block device number as major:minor. e.g. 8:0
diff ./drivers/md/md.c~current~ ./drivers/md/md.c
--- ./drivers/md/md.c~current~ 2006-06-01 15:05:30.000000000 +1000
+++ ./drivers/md/md.c 2006-06-01 15:05:30.000000000 +1000
@@ -2235,6 +2235,30 @@ chunk_size_store(mddev_t *mddev, const c
static struct md_sysfs_entry md_chunk_size =
__ATTR(chunk_size, 0644, chunk_size_show, chunk_size_store);
+static ssize_t
+resync_start_show(mddev_t *mddev, char *page)
+{
+ return sprintf(page, "%llu\n", (unsigned long long)mddev->recovery_cp);
+}
+
+static ssize_t
+resync_start_store(mddev_t *mddev, const char *buf, size_t len)
+{
+ /* can only set chunk_size if array is not yet active */
+ char *e;
+ unsigned long long n = simple_strtoull(buf, &e, 10);
+
+ if (mddev->pers)
+ return -EBUSY;
+ if (!*buf || (*e && *e != '\n'))
+ return -EINVAL;
+
+ mddev->recovery_cp = n;
+ return len;
+}
+static struct md_sysfs_entry md_resync_start =
+__ATTR(resync_start, 0644, resync_start_show, resync_start_store);
+
/*
* The array state can be:
*
@@ -2771,6 +2795,7 @@ static struct attribute *md_default_attr
&md_raid_disks.attr,
&md_chunk_size.attr,
&md_size.attr,
+ &md_resync_start.attr,
&md_metadata.attr,
&md_new_device.attr,
&md_safe_delay.attr,
@@ -3263,6 +3288,7 @@ static int do_md_stop(mddev_t * mddev, i
mddev->array_size = 0;
mddev->size = 0;
mddev->raid_disks = 0;
+ mddev->recovery_cp = 0;
disk = mddev->gendisk;
if (disk)
next prev parent reply other threads:[~2006-06-01 5:14 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-06-01 5:13 [PATCH 000 of 10] md: Introduction - assorted patches for -mm NeilBrown
2006-06-01 5:13 ` [PATCH 001 of 10] md: md Kconfig speeling feex NeilBrown
2006-06-01 5:13 ` [PATCH 002 of 10] md: Fix Kconfig error NeilBrown
2006-06-01 5:13 ` [PATCH 003 of 10] md: Fix bug that stops raid5 resync from happening NeilBrown
2006-06-01 5:13 ` [PATCH 004 of 10] md: Allow re-add to work on array without bitmaps NeilBrown
2006-06-01 5:13 ` [PATCH 005 of 10] md: Don't write dirty/clean update to spares - leave them alone NeilBrown
2006-06-01 5:13 ` [PATCH 006 of 10] md: Set/get state of array via sysfs NeilBrown
2006-06-01 5:33 ` Chris Wright
2006-06-01 5:43 ` Neil Brown
2006-06-01 5:14 ` [PATCH 007 of 10] md: Allow rdev state to be set " NeilBrown
2006-06-01 5:14 ` [PATCH 008 of 10] md: Allow raid 'layout' to be read and " NeilBrown
2006-06-01 5:34 ` Chris Wright
2006-06-01 5:44 ` Neil Brown
2006-06-01 5:14 ` NeilBrown [this message]
2006-06-01 5:14 ` [PATCH 010 of 10] md: Allow the write_mostly flag to be " NeilBrown
2006-08-05 5:59 ` Mike Snitzer
2006-08-05 23:43 ` Mike Snitzer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1060601051413.27649@suse.de \
--to=neilb@suse.de \
--cc=akpm@osdl.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).