From: Robin Hill <robin@robinhill.me.uk>
To: Linux-RAID <linux-raid@vger.kernel.org>
Subject: Re: What's the typical RAID10 setup?
Date: Mon, 31 Jan 2011 15:21:51 +0000 [thread overview]
Message-ID: <20110131152151.GD7861@cthulhu.home.robinhill.me.uk> (raw)
In-Reply-To: <AANLkTimoSvWj3mnowZbVKKHEMzwjiQ=WqRUUsj91n_Zr@mail.gmail.com>
On Mon Jan 31, 2011 at 01:00:13PM -0200, Roberto Spadim wrote:
> i think make two very big raid 0
> and after raid1
> is better
>
Not really - you increase the failure risk doing this. With this setup,
a single drive failure from each RAID0 array will lose you the entire
array. With the reverse (RAID0 over RAID1) then you require both drives
in the RAID1 to fail in order to lose the array. Of course, with a 4
drive array then the risk is the same (33% with 2 drive failures) but
with a 6 drive array it changes to 60% for RAID1 over RAID0 versus 20%
for RAID0 over RAID1.
Cheers,
Robin
next prev parent reply other threads:[~2011-01-31 15:21 UTC|newest]
Thread overview: 127+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-01-31 9:41 What's the typical RAID10 setup? Mathias Burén
2011-01-31 10:14 ` Robin Hill
2011-01-31 10:22 ` Mathias Burén
2011-01-31 10:36 ` CoolCold
2011-01-31 15:00 ` Roberto Spadim
2011-01-31 15:21 ` Robin Hill [this message]
2011-01-31 15:27 ` Roberto Spadim
2011-01-31 15:28 ` Roberto Spadim
2011-01-31 15:32 ` Roberto Spadim
2011-01-31 15:34 ` Roberto Spadim
2011-01-31 15:37 ` Roberto Spadim
2011-01-31 15:45 ` Robin Hill
2011-01-31 16:55 ` Denis
2011-01-31 17:31 ` Roberto Spadim
2011-01-31 18:35 ` Denis
2011-01-31 19:15 ` Roberto Spadim
2011-01-31 19:28 ` Keld Jørn Simonsen
2011-01-31 19:35 ` Roberto Spadim
2011-01-31 19:37 ` Roberto Spadim
2011-01-31 20:22 ` Keld Jørn Simonsen
2011-01-31 20:17 ` Stan Hoeppner
2011-01-31 20:37 ` Keld Jørn Simonsen
2011-01-31 21:20 ` Roberto Spadim
2011-01-31 21:24 ` Mathias Burén
2011-01-31 21:27 ` Jon Nelson
2011-01-31 21:47 ` Roberto Spadim
2011-01-31 21:51 ` Roberto Spadim
2011-01-31 22:50 ` NeilBrown
2011-01-31 22:53 ` Roberto Spadim
2011-01-31 23:10 ` NeilBrown
2011-01-31 23:14 ` Roberto Spadim
2011-01-31 22:52 ` Keld Jørn Simonsen
2011-01-31 23:00 ` Roberto Spadim
2011-02-01 10:01 ` David Brown
2011-02-01 13:50 ` Jon Nelson
2011-02-01 14:25 ` Roberto Spadim
2011-02-01 14:48 ` David Brown
2011-02-01 15:41 ` Roberto Spadim
2011-02-03 3:36 ` Drew
2011-02-03 8:18 ` Stan Hoeppner
[not found] ` <AANLkTikerSZfhMbkEvGBVyLB=wHDSHLWszoEz5As5Hi4@mail.gmail.com>
[not found] ` <AANLkTikLyR206x4aMy+veNkWPV67uF9r5dZKGqXJUEqN@mail.gmail.com>
2011-02-03 14:35 ` Roberto Spadim
2011-02-03 15:43 ` Keld Jørn Simonsen
2011-02-03 15:50 ` Roberto Spadim
2011-02-03 15:54 ` Roberto Spadim
2011-02-03 16:02 ` Keld Jørn Simonsen
2011-02-03 16:07 ` Roberto Spadim
2011-02-03 16:16 ` Roberto Spadim
2011-02-01 22:05 ` Stan Hoeppner
2011-02-01 23:12 ` Roberto Spadim
2011-02-02 9:25 ` Robin Hill
2011-02-02 16:00 ` Roberto Spadim
2011-02-02 16:06 ` Roberto Spadim
2011-02-02 16:07 ` Roberto Spadim
2011-02-02 16:10 ` Roberto Spadim
2011-02-02 16:13 ` Roberto Spadim
2011-02-02 19:44 ` Keld Jørn Simonsen
2011-02-02 20:28 ` Roberto Spadim
2011-02-02 21:31 ` Roberto Spadim
2011-02-02 22:13 ` Keld Jørn Simonsen
2011-02-02 22:26 ` Roberto Spadim
2011-02-03 1:57 ` Roberto Spadim
2011-02-03 3:05 ` Stan Hoeppner
2011-02-03 3:13 ` Roberto Spadim
2011-02-03 3:17 ` Roberto Spadim
2011-02-01 23:35 ` Keld Jørn Simonsen
2011-02-01 16:02 ` Keld Jørn Simonsen
2011-02-01 16:24 ` Roberto Spadim
2011-02-01 17:56 ` Keld Jørn Simonsen
2011-02-01 18:09 ` Roberto Spadim
2011-02-01 20:16 ` Keld Jørn Simonsen
2011-02-01 20:32 ` Keld Jørn Simonsen
2011-02-01 20:58 ` Roberto Spadim
2011-02-01 21:04 ` Roberto Spadim
2011-02-01 21:18 ` David Brown
2011-02-01 0:58 ` Stan Hoeppner
2011-02-01 12:50 ` Roman Mamedov
2011-02-03 11:04 ` Keld Jørn Simonsen
2011-02-03 14:17 ` Roberto Spadim
2011-02-03 15:54 ` Keld Jørn Simonsen
2011-02-03 18:39 ` Keld Jørn Simonsen
2011-02-03 18:41 ` Roberto Spadim
2011-02-03 23:43 ` Stan Hoeppner
2011-02-04 3:49 ` hansbkk
2011-02-04 7:06 ` Keld Jørn Simonsen
2011-02-04 8:27 ` Stan Hoeppner
2011-02-04 9:06 ` Keld Jørn Simonsen
2011-02-04 10:04 ` Stan Hoeppner
2011-02-04 11:15 ` hansbkk
2011-02-04 13:33 ` Keld Jørn Simonsen
2011-02-04 20:35 ` Keld Jørn Simonsen
2011-02-04 20:42 ` Keld Jørn Simonsen
2011-02-04 21:15 ` Stan Hoeppner
2011-02-04 22:05 ` Keld Jørn Simonsen
2011-02-04 23:03 ` Stan Hoeppner
2011-02-06 3:59 ` Drew
2011-02-06 4:27 ` Stan Hoeppner
2011-02-04 11:34 ` David Brown
2011-02-04 13:53 ` Keld Jørn Simonsen
2011-02-04 14:17 ` David Brown
2011-02-04 14:21 ` hansbkk
2011-02-06 4:02 ` Drew
2011-02-06 7:58 ` Keld Jørn Simonsen
2011-02-06 12:03 ` Roman Mamedov
2011-02-06 14:30 ` Roberto Spadim
2011-02-01 8:46 ` hansbkk
2011-01-31 19:37 ` Phillip Susi
2011-01-31 19:41 ` Roberto Spadim
2011-01-31 19:46 ` Phillip Susi
2011-01-31 19:53 ` Roberto Spadim
2011-01-31 22:10 ` Phillip Susi
2011-01-31 22:14 ` Denis
2011-01-31 22:33 ` Roberto Spadim
2011-01-31 22:36 ` Roberto Spadim
2011-01-31 20:23 ` Stan Hoeppner
2011-01-31 21:59 ` Phillip Susi
2011-01-31 22:08 ` Jon Nelson
2011-01-31 22:38 ` Phillip Susi
2011-02-01 10:05 ` David Brown
2011-02-01 9:20 ` Robin Hill
2011-02-04 16:03 ` Phillip Susi
2011-02-04 16:22 ` Robin Hill
2011-02-04 20:35 ` [OT] " Phil Turmel
2011-02-04 20:35 ` Phillip Susi
2011-02-04 21:05 ` Stan Hoeppner
2011-02-04 21:13 ` Roberto Spadim
2011-01-31 15:30 ` Robin Hill
2011-01-31 20:07 ` Stan Hoeppner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110131152151.GD7861@cthulhu.home.robinhill.me.uk \
--to=robin@robinhill.me.uk \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).