From: Julie Ashworth <ashworth@berkeley.edu>
To: Phil Turmel <philip@turmel.org>
Cc: linux-raid@vger.kernel.org
Subject: Re: request help with RAID1 array that endlessly attempts to sync
Date: Tue, 17 Dec 2013 19:45:56 -0800 [thread overview]
Message-ID: <20131218034556.GA9457@localhost.localdomain> (raw)
In-Reply-To: <52B0A956.7030501@turmel.org>
[-- Attachment #1: Type: text/plain, Size: 1216 bytes --]
hi Phil,
thanks again for your help. It was surprisingly easy to install the latest smarmontools.
On 17-12-2013 14.43 -0500, Phil Turmel wrote:
> I was interested in the reallocation counts, the current pending
> sectors, and the scterc timeouts. The latter were not present, and are
> important.
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 3
197 Current_Pending_Sector -O--C- 100 100 000 - 1
SCT Error Recovery Control:
Read: 100 (10.0 seconds)
Write: 100 (10.0 seconds)
(I also attached the full output)
I verified that a weekly scrub is performed via cron (default with Centos5), and there were no errors detected prior to the sync. The output is included in syslog reports.
> But /dev/sdb has three relocations and only one pending error. That's
> an old drive, but not sick. I'd be concerned that there're other
> hardware issues in your system if the timeout issue is not part of the
> problem.
Should I run the sync (mdadm -a) in verbose mode? If so, what is the best way to terminate the current sync? By failing/removing /dev/sda?
Thanks in advance!
best,
Julie
----
[-- Attachment #2: smartctl-6.2-sdb.out --]
[-- Type: text/plain, Size: 17840 bytes --]
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-2.6.18-238.12.1.el5] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda ES.2
Device Model: ST31000340NS
Serial Number: 9QJ6Y79S
LU WWN Device Id: 5 000c50 01a89c17b
Firmware Version: SN06
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Dec 17 19:41:28 2013 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 625) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 220) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 083 062 044 - 208852444
3 Spin_Up_Time PO---- 099 099 000 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 30
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 3
7 Seek_Error_Rate POSR-- 081 060 030 - 131804707
9 Power_On_Hours -O--CK 067 067 000 - 29583
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 037 020 - 30
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 098 098 000 - 2
188 Command_Timeout -O--CK 100 096 000 - 42950328381
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 079 060 045 - 21 (Min/Max 21/22)
194 Temperature_Celsius -O---K 021 040 000 - 21 (0 15 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 057 048 000 - 208852444
197 Current_Pending_Sector -O--C- 100 100 000 - 1
198 Offline_Uncorrectable ----C- 100 100 000 - 1
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 65 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2864 Device vendor specific log
0xb6 GPL VS 1918 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 60 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 60 [19] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 74 5c d2 99 40 00 24d+00:14:08.396 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:14:08.368 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:14:08.367 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 24d+00:14:08.353 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:14:08.326 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 59 [18] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 74 5c d2 99 40 00 24d+00:14:05.247 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:14:05.220 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:14:05.218 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 24d+00:14:05.205 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:14:05.177 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 58 [17] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 74 5c d2 99 40 00 24d+00:14:02.124 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:14:02.096 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:14:02.095 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 24d+00:14:02.081 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:14:02.054 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 57 [16] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 74 5c d2 99 40 00 24d+00:13:58.992 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:13:58.964 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:13:58.963 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 24d+00:13:58.950 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:13:58.922 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 56 [15] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 74 5c d2 99 40 00 24d+00:13:55.835 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:13:55.808 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:13:55.806 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 24d+00:13:55.793 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:13:55.765 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 55 [14] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 74 5c d2 99 40 00 24d+00:13:52.680 READ FPDMA QUEUED
60 00 00 00 08 00 00 74 5c d2 89 40 00 24d+00:13:52.671 READ FPDMA QUEUED
60 00 00 00 08 00 00 74 5c d2 81 40 00 24d+00:13:52.664 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:13:52.657 FLUSH CACHE EXT
61 00 00 00 08 00 00 74 70 59 01 40 00 24d+00:13:52.657 WRITE FPDMA QUEUED
Error 54 [13] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 80 00 00 74 5c d2 81 40 00 24d+00:13:49.491 READ FPDMA QUEUED
60 00 00 00 80 00 00 74 5c d3 01 40 00 24d+00:13:49.490 READ FPDMA QUEUED
60 00 00 00 80 00 00 74 5c d3 81 40 00 24d+00:13:49.488 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:13:49.461 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:13:49.459 IDENTIFY DEVICE
Error 53 [12] occurred at disk power-on lifetime: 29572 hours (1232 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 74 5c d2 9b 00 00 Error: UNC at LBA = 0x745cd29b = 1952240283
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 80 00 00 74 5c d3 81 40 00 24d+00:13:46.341 READ FPDMA QUEUED
60 00 00 00 80 00 00 74 5c d3 01 40 00 24d+00:13:46.341 READ FPDMA QUEUED
60 00 00 00 80 00 00 74 5c d2 81 40 00 24d+00:13:46.340 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 24d+00:13:46.312 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 24d+00:13:46.311 IDENTIFY DEVICE
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 60% 29560 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 21 Celsius
Power Cycle Min/Max Temperature: 21/22 Celsius
Lifetime Min/Max Temperature: 15/40 Celsius
Under/Over Temperature Limit Count: 0/66
SCT Temperature History Version: 2
Temperature Sampling Period: 10 minutes
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/ 0 Celsius
Min/Max Temperature Limit: 0/ 0 Celsius
Temperature History Size (Index): 128 (71)
Index Estimated Time Temperature Celsius
72 2013-12-16 22:30 22 ***
... ..( 7 skipped). .. ***
80 2013-12-16 23:50 22 ***
81 2013-12-17 00:00 21 **
82 2013-12-17 00:10 22 ***
83 2013-12-17 00:20 21 **
84 2013-12-17 00:30 22 ***
85 2013-12-17 00:40 21 **
... ..( 3 skipped). .. **
89 2013-12-17 01:20 21 **
90 2013-12-17 01:30 22 ***
... ..( 7 skipped). .. ***
98 2013-12-17 02:50 22 ***
99 2013-12-17 03:00 21 **
... ..( 9 skipped). .. **
109 2013-12-17 04:40 21 **
110 2013-12-17 04:50 22 ***
... ..( 7 skipped). .. ***
118 2013-12-17 06:10 22 ***
119 2013-12-17 06:20 21 **
... ..( 10 skipped). .. **
2 2013-12-17 08:10 21 **
3 2013-12-17 08:20 22 ***
4 2013-12-17 08:30 22 ***
5 2013-12-17 08:40 ? -
6 2013-12-17 08:50 22 ***
7 2013-12-17 09:00 22 ***
8 2013-12-17 09:10 22 ***
9 2013-12-17 09:20 21 **
10 2013-12-17 09:30 22 ***
11 2013-12-17 09:40 22 ***
12 2013-12-17 09:50 21 **
... ..( 42 skipped). .. **
55 2013-12-17 17:00 21 **
56 2013-12-17 17:10 22 ***
57 2013-12-17 17:20 21 **
... ..( 13 skipped). .. **
71 2013-12-17 19:40 21 **
SCT Error Recovery Control:
Read: 100 (10.0 seconds)
Write: 100 (10.0 seconds)
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
next prev parent reply other threads:[~2013-12-18 3:45 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-12-17 6:50 request help with RAID1 array that endlessly attempts to sync Julie Ashworth
2013-12-17 16:53 ` Julie Ashworth
2013-12-17 17:55 ` Phil Turmel
2013-12-17 19:26 ` Julie Ashworth
2013-12-17 19:43 ` Phil Turmel
2013-12-17 23:12 ` David C. Rankin
2013-12-18 3:45 ` Julie Ashworth [this message]
2013-12-18 12:08 ` Phil Turmel
2014-01-21 6:38 ` Julie Ashworth
2014-01-21 13:23 ` Phil Turmel
2014-02-25 0:16 ` Julie Ashworth
2013-12-17 18:12 ` Wilson Jonathan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20131218034556.GA9457@localhost.localdomain \
--to=ashworth@berkeley.edu \
--cc=linux-raid@vger.kernel.org \
--cc=philip@turmel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).