RAID-0 Autodetection fails

[Agustinus Tedja <agustinus.tedja@infodesign-osd.de>]

Hello everybody,
I am installing Linux SuSE 8.0 with kernel version 2.4.18-4GB. This
kernel should have already contain the Software-RAID module as
advertised by SuSE.
I have 3 equal drives. For simplicity I installed complete Linux only in
a drive hdb(the boot and the root is in this normal drive) and now I am
trying to make a RAID level 0 with the rest 2 drives called hdc and hdd. 
I have made these two drives into a RAID-drive called /dev/md0 with
YaST2 help and it was successfully mounted and used.
But each time I rebooted the system, this /dev/md0 could not be
recognized at startup and all data in /dev/md0 was lost as well. I
needed to mount it again afterwards, that made it a silly idea.
What is wrong ? Any hints and helps are gladly welcomed.

Here is the message on boot:
...
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6> |events: 0000009a]
<6> |events: 0000009a]
<6>md: autorun ...
<6>md: considering hdd1 ...
<6>md:  adding hdd1 ...
<6>md:  adding hdc1 ...
<6>md: created md0
<6>md: bind<hdc1,1>
<6>md: bind<hdd1,2>
<6>md: running: <hdd1><hdc1>
<6>md: hdd1's event counter: 0000009a
<6>md: hdc1's event counter: 0000009a
<3>request_module[md-personality-2]: Root fs not mounted
<3>md: personality 2 is not loaded!
<4>md: do_md_run() returned -22
<6>md: md0 stopped.
<6>md: unbind<hdd1,1>
<6>md: export_rdev(hdd1)
<6>md: unbind<hdc1,0>
<6>md: export_rdev(hdc1)
<6>md: ... autorun DONE.

...and after some lines below there is other messages:

<3>md: invalid raid superblock magic on hdc
<4>md: hdc has invalid sb, not importing!
<4>md: could not import hdc!
<4>md: autostart hdc failed!
<6>md: Autodetecting RAID arrays.
<6> |events: 0000009a]
<6> |events: 0000009a]
<6>md: autorun ...
<6>md: considering hdd1 ...
<6>md:  adding hdd1 ...
<6>md:  adding hdc1 ...
<6>md: created md0
<6>md: bind<hdc1,1>
<6>md: bind<hdd1,2>
<6>md: running: <hdd1><hdc1>
<6>md: hdc1's event counter: 0000009a
<6>md: hdd1's event counter: 0000009a
<6>md: raid0 personality readahead registered as nr 2
<6>md0: max total readahead window set to 496k
<6>md0: 2 data-disks, max readahead per data-disk: 248k
<4>raid0: looking at hdc1
<4>raid0:   comparing hdc1 (80418112) with hdc1(80418112)
<4>raid0:   END
<4>raid0:   ==> UNIQUE
<4>raid0: 1 zones
<4>raid0: looking at hdd1
<4>raid0:   comparing hdd1 (80418112) with hdc1(80418112)
<4>raid0:   EQUAL
<4>raid0: FINAL 1 zones
<4>raid0: zone 0
<4>raid0:
<4>raid0:
<4>raid0:
<4>raid0:
<4>raid0:
<4>raid0:
<4>raid0:
<4>raid0:
<4>raid0:

FYI here I give the content of some important files:
/etc/fstab:
	/dev/hdb3	/		reiserfs	defaults 1 2
	/dev/hdb2	/boot		reiserfs	defaults 1 2
	/dev/md0	/dataraid	auto		noauto, user 0 0
	devpts		/dev/pts	devpts		defaults 0 0
	/dev/cdrecorder	/media/cdrecorder auto		ro,noauto,user,exec 0 0
	/dev/cdrom	/media/cdrom	auto		noauto,user,exec 0 0
	/dev/fd0	/media/floppy	auto		noauto,user,sync 0 0
	usbdevs		/proc/bus/usb	usbdevs		noauto 0 0
	proc		/proc		proc		defaults 0 0
	/dev/hdb1	swap		swap		pri=42 0 0	

/etc/raidtab:
	raiddev /dev/md0
	raid-level 0
	nr-raid-disks 2
	persistent-superblock 1
	chunk-size 32
	device /dev/hdc
	raid-disk 0
	device /dev/hdd
	raid-disk 1

/etc/mtab: (not mdtab, inside there is no md0 entry)
	/dev/hdb3 	/	reiserfs	rw 0 0
	proc		/proc	proc		rw 0 0
	devpts		/dev/pts devpts		rw 0 0
	/dev/hdb2	/boot	reiserfs	rw 0 0
	shmfs		/dev/shm  shm		rw 0 0
	usbdevfs 	/proc/bus/usb  usbdevs	rw 0 0