Handling of read errors in raid6

Handling of read errors in raid6

[Filipe Maia]

Is it easy to port the "readerrors rewrite" patch to RAID6?

Are there any plans to do it?

If there are are they short or long term?

(I have some stuff in a RAID6 that has more than 2 disks with
bad sectors and i would like to see if it would be possible to
recover them without going through all the dd stuff).

Thanks for the help.


-- 
All generalizations are false, including this one.
          -- Mark Twain

attempt to access beyond end of device

[PFC]

	OK, I was a bit stupid...

	I changed a drive today, so I rebuilt a software RAID1.
	I have a RAID1 in degraded mode (1 out of 2 drives), and I added a new  
partition to it. When I say I was stupid, I mean the partition I added was  
a tiny little bit smaller than what it should have been.

	md happily added it, synced, then at the very end :

Jan 19 21:33:27 apollo13 attempt to access beyond end of device
Jan 19 21:33:27 apollo13 sda7: rw=1, want=12498560, limit=12498507
Jan 19 21:33:27 apollo13 raid1: Disk failure on sda7, disabling device.
Jan 19 21:33:27 apollo13        Operation continuing on 1 devices

	Of course, "attempt to access beyond end of device", I made the device  
too small. Duh.

	No problem, I'll just fix my partition, but a warning message on the  
mdadm --add would have avoided losing time doing the sync, and at the end,  
a few seconds of "WTF ? it failed ? ah, ok..."

	Have a nice day !


mdadm --version
mdadm - v2.1 - 12 September 2005

raid reconstruction speed

[PFC]

	Sorry for flooding ;)

	I have the following configuration :
	- two disks (hda and sda)
	- each disk has 2 partitions (hda1/sda1) and (hda2/sda2)
	- two raid1 md devices are made :
	md0 = sda1 + hda1, contains the OS
	md1 = sda2 + hda2, contains a database

	I made 2 devices because I wanted to use different FS's.

	When rebuilding md1, it does not realize accesses to md0 wait for the  
same disks. Thus reconstruction of md1 runs happily at full speed, and the  
machine is dog slow, because the OS and everything is on md0.
	(I cat /dev/zero to a file on md1 to slow the rebuild so it would let me  
start a web browser so I don't get bored to death)

	When rebuilding md0, the rebuild process detects accesses to md0 and  
behaves nicely (the machine is responsive). However, it does not realize  
that md1 is on the same disks, thus the databases are dog slow.

	Fortunately, as the rebuild runs ar full speed, the pain does not last  
long. It took 5 minutes to start this email client though.
	Thought you might wanna know ;)

	Regards,

	Pierre Caillaud

Re: raid reconstruction speed

[Mike Hardy]

PFC wrote:

>     When rebuilding md1, it does not realize accesses to md0 wait for
> the  same disks. Thus reconstruction of md1 runs happily at full speed,
> and the  machine is dog slow, because the OS and everything is on md0.
>     (I cat /dev/zero to a file on md1 to slow the rebuild so it would
> let me  start a web browser so I don't get bored to death)

echo "10000" > /proc/sys/dev/raid/speed-limit-max (or similar?)

You can do that in /etc/rc.local or something to make sure it sticks,
then you'll be able to use your machine while any array rebuilds.

I guess the feature you're asking for is for md to guess that accessing
any partition component on a disk that has a partition being rebuilt
should throttle the rebuild, right?

Can that heuristic be successful at all times? I think it might.

Does md have enough information to do that? I don't know...

-Mike

Re: raid reconstruction speed

[Mark Hahn]

> echo "10000" > /proc/sys/dev/raid/speed-limit-max (or similar?)
> 
> You can do that in /etc/rc.local or something to make sure it sticks,

echo "dev.raid.speed_limit_max = 10000" >> /etc/sysctl.conf
is another, perhaps nicer way to make the setting permanent.

Re: raid reconstruction speed

[Neil Brown]

On Thursday January 19, lists@peufeu.com wrote:
> 
> 	Sorry for flooding ;)
> 
> 	I have the following configuration :
> 	- two disks (hda and sda)
> 	- each disk has 2 partitions (hda1/sda1) and (hda2/sda2)
> 	- two raid1 md devices are made :
> 	md0 = sda1 + hda1, contains the OS
> 	md1 = sda2 + hda2, contains a database
> 
> 	I made 2 devices because I wanted to use different FS's.
> 
> 	When rebuilding md1, it does not realize accesses to md0 wait for the  
> same disks. Thus reconstruction of md1 runs happily at full speed, and the  
> machine is dog slow, because the OS and everything is on md0.

Hmmm.. it should.  md measures activity on a component by looking at
the activity of the whole device holding that component.    So any
activity on hda or sda should slow down rebuild of md0 or md1.
It is very strange that it doesn't...

What kernel are you using?

NeilBrown

Re: raid reconstruction speed

[PFC]

> What kernel are you using?
>
> NeilBrown

Kernel version : 2.6.15-gentoo

Yes, it's strange... Not very annoying, as the rebuild is finished already  
(at 40 MB/s it was short), but strange.