From: Christopher Smith <csmith@nighthawkrad.net>
To: Brad Campbell <brad@wasp.net.au>
Cc: linux-raid@vger.kernel.org
Subject: Re: Problems with multiple Promise SATA150 TX4 cards
Date: Wed, 25 Jan 2006 11:15:04 +1100 [thread overview]
Message-ID: <43D6C308.5040603@nighthawkrad.net> (raw)
In-Reply-To: <43D62B4F.1080505@nighthawkrad.net>
Christopher Smith wrote:
> Brad Campbell wrote:
>> Can you send an lspci -vv please? I did have some strange problems
>> with the BIOS setting up weird timing modes on some of the cards. This
>> did not present a reliability problem for me, just performance however.
>
> I attached lspci output to my original post. I have also included it on
> the end of this one (with a slight difference regarding which slots the
> cards were in, but that makes no difference to the problem).
Oops, forgot to attach lspci output - that's what you get for posting
just before bed :).
[root@terminus ~]# lspci -vv
00:00.0 Host bridge: Intel Corporation E7501 Memory Controller Hub (rev 01)
Subsystem: Intel Corporation E7501 Memory Controller Hub
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [40] Vendor Specific Information
00:02.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface B
PCI-to-PCI Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: fc400000-fc6fffff
Prefetchable memory behind bridge: ff300000-ff5fffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:03.0 PCI bridge: Intel Corporation E7500/E7501 Hub Interface C
PCI-to-PCI Bridge (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=04, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc700000-fc9fffff
Prefetchable memory behind bridge: ff600000-ff8fffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #1) (rev
02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 209
Region 4: I/O ports at ec00 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #2) (rev
02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 217
Region 4: I/O ports at e880 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801CA/CAM USB (Hub #3) (rev
02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 169
Region 4: I/O ports at e800 [size=32]
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 42) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: ff900000-ff9fffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801CA LPC Interface Controller
(rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801CA Ultra ATA Storage
Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 88000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0540 [size=32]
01:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc6ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=1 Dev=28 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=01, secondary=02, subordinate=02, sec-latency=48
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fc400000-fc4fffff
Prefetchable memory behind bridge:
00000000ff300000-00000000ff300000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=0
Status: Bus=1 Dev=29 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
01:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc6fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=1 Dev=30 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fc500000-fc5fffff
Prefetchable memory behind bridge:
00000000ff400000-00000000ff400000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=3
Status: Bus=1 Dev=31 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
02:02.0 Mass storage controller: Promise Technology, Inc. PDC20318
(SATA150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20318 (SATA150 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 4500ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at ac00 [size=64]
Region 1: I/O ports at a880 [size=16]
Region 2: I/O ports at a800 [size=128]
Region 3: Memory at fc4ff000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fc4c0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fc4f8000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:02.0 Ethernet controller: Intel Corporation 82544GC Gigabit Ethernet
Controller (LOM) (rev 02)
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 201
Region 0: Memory at fc5e0000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at fc5c0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at bc00 [size=32]
Expansion ROM at fc5a0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=3 Dev=2 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=2, DMOST=0, DMCRS=1, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
04:1c.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc9ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=4 Dev=28 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
04:1d.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=04, secondary=05, subordinate=05, sec-latency=64
Memory behind bridge: fc700000-fc7fffff
Prefetchable memory behind bridge:
00000000ff600000-00000000ff600000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=3
Status: Bus=4 Dev=29 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
04:1e.0 PIC: Intel Corporation 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if
20 [IO(X)-APIC])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc9fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=4 Dev=30 Func=0 64bit+ 133MHz+ SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
04:1f.0 PCI bridge: Intel Corporation 82870P2 P64H2 Hub PCI Bridge (rev
04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=04, secondary=06, subordinate=06, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc800000-fc8fffff
Prefetchable memory behind bridge:
00000000ff700000-00000000ff700000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=0
Status: Bus=4 Dev=31 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
06:03.0 Mass storage controller: Promise Technology, Inc. PDC20318
(SATA150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20318 (SATA150 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 90
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at cc00 [size=64]
Region 1: I/O ports at c880 [size=16]
Region 2: I/O ports at c800 [size=128]
Region 3: Memory at fc8ff000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fc8c0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at fc8f8000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
07:02.0 Mass storage controller: Promise Technology, Inc. PDC20318
(SATA150 TX4) (rev 02)
Subsystem: Promise Technology, Inc. PDC20318 (SATA150 TX4)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 90
Interrupt: pin A routed to IRQ 193
Region 0: I/O ports at dc00 [size=64]
Region 1: I/O ports at d480 [size=16]
Region 2: I/O ports at d400 [size=128]
Region 3: Memory at feafe000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at feaa0000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at ff920000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
07:0c.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA])
Subsystem: Gateway 2000: Unknown device 891f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at ff900000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[root@terminus ~]#
next prev parent reply other threads:[~2006-01-25 0:15 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-24 2:01 Problems with multiple Promise SATA150 TX4 cards Christopher Smith
2006-01-24 6:39 ` Mark Hahn
2006-01-24 6:58 ` Christopher Smith
2006-01-24 9:11 ` Brad Campbell
2006-01-24 13:27 ` Christopher Smith
2006-01-25 0:15 ` Christopher Smith [this message]
2006-01-25 5:33 ` Mattias Wadenstein
2006-01-24 17:40 ` David Greaves
2006-01-25 10:04 ` Erik Slagter
2006-01-26 0:26 ` Christopher Smith
2006-01-26 11:35 ` Erik Slagter
2006-01-26 14:22 ` David Greaves
2006-01-26 14:44 ` Hans Kristian Rosbach
2006-01-27 6:00 ` Mitchell Laks
2006-01-27 13:21 ` berk walker
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43D6C308.5040603@nighthawkrad.net \
--to=csmith@nighthawkrad.net \
--cc=brad@wasp.net.au \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).