* And again help on deciphering an error
@ 2008-10-28 23:53 Peter Rabbitson
2008-10-29 8:08 ` Justin Piszcz
2008-11-14 18:23 ` And again help on deciphering an error (continued) Peter Rabbitson
0 siblings, 2 replies; 11+ messages in thread
From: Peter Rabbitson @ 2008-10-28 23:53 UTC (permalink / raw)
To: linux-raid
Hello,
Before I ask my question - if there is some documentation that answers
what I am asking - I would be thrilled to read it. So far google has not
helped me at all.
This being said I need help with understanding what is going on here
(full log):
Oct 27 11:33:41 Arzamas kernel: ata6.00: exception Emask 0x10 SAct 0x0
SErr 0x80000 action 0xe frozen
Oct 27 11:33:41 Arzamas kernel: ata6.00: irq_stat 0x01100010, PHY RDY
changed
Oct 27 11:33:41 Arzamas kernel: ata6: SError: { 10B8B }
Oct 27 11:33:41 Arzamas kernel: ata6.00: cmd
ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
Oct 27 11:33:41 Arzamas kernel: res 06/37:00:00:00:00/00:00:00:00:06/00
Emask 0x12 (ATA bus error)
Oct 27 11:33:41 Arzamas kernel: ata6.00: error: { IDNF ABRT }
Oct 27 11:33:41 Arzamas kernel: ata6: hard resetting link
Oct 27 11:33:46 Arzamas kernel: ata6: SATA link up 3.0 Gbps (SStatus 123
SControl 0)
Oct 27 11:33:46 Arzamas kernel: ata6.00: configured for UDMA/100
Oct 27 11:33:46 Arzamas kernel: ata6: EH complete
Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] 488397168 512-byte
hardware sectors (250059 MB)
Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write Protect is off
Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Oct 27 11:33:46 Arzamas kernel: end_request: I/O error, dev sde, sector
488166955
Oct 27 11:33:46 Arzamas kernel: md: super_written gets error=-5, uptodate=0
Oct 27 11:33:46 Arzamas kernel: raid10: Disk failure on sde2, disabling
device.
Oct 27 11:33:46 Arzamas kernel: raid10: Operation continuing on 3 devices.
Oct 27 11:33:46 Arzamas kernel: RAID10 conf printout:
Oct 27 11:33:46 Arzamas kernel: --- wd:3 rd:4
Oct 27 11:33:46 Arzamas kernel: disk 0, wo:0, o:1, dev:sdc2
Oct 27 11:33:46 Arzamas kernel: disk 1, wo:0, o:1, dev:sdb2
Oct 27 11:33:46 Arzamas kernel: disk 2, wo:1, o:0, dev:sde2
Oct 27 11:33:46 Arzamas kernel: disk 3, wo:0, o:1, dev:sdd2
Oct 27 11:33:46 Arzamas kernel: RAID10 conf printout:
Oct 27 11:33:46 Arzamas kernel: --- wd:3 rd:4
Oct 27 11:33:46 Arzamas kernel: disk 0, wo:0, o:1, dev:sdc2
Oct 27 11:33:46 Arzamas kernel: disk 1, wo:0, o:1, dev:sdb2
Oct 27 11:33:46 Arzamas kernel: disk 3, wo:0, o:1, dev:sdd2
Afterwards I removed sde from all arrays and mounts, and grilled it
repeatedly with badblocks and smartctl -t long. Nothing came out for
over a day. Below see the smartclt -a output. This happened one day
after I upgraded to 2.6.27.4 from 2.6.23.
Can someone please tell me what seems to be dying? Thank you!
root@Arzamas:~# smartctl -a /dev/sde
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Second Generation Serial ATA family
Device Model: WDC WD2500AAJS-00B4A0
Serial Number: WD-WCAT11669666
Firmware Version: 01.03A01
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Oct 28 19:52:16 2008 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (6180) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 75) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0027 175 153 021 Pre-fail Always
- 2250
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 17
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always
- 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 694
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 17
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always
- 13
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always
- 17
194 Temperature_Celsius 0x0022 106 100 000 Old_age Always
- 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 694
-
# 2 Extended offline Completed without error 00% 684
-
# 3 Extended offline Completed without error 00% 663
-
# 4 Short offline Aborted by host 60% 662
-
# 5 Short offline Completed without error 00% 662
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@Arzamas:~#
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error
2008-10-28 23:53 And again help on deciphering an error Peter Rabbitson
@ 2008-10-29 8:08 ` Justin Piszcz
2008-11-14 18:23 ` And again help on deciphering an error (continued) Peter Rabbitson
1 sibling, 0 replies; 11+ messages in thread
From: Justin Piszcz @ 2008-10-29 8:08 UTC (permalink / raw)
To: Peter Rabbitson; +Cc: linux-raid
On Wed, 29 Oct 2008, Peter Rabbitson wrote:
> Hello,
>
> Before I ask my question - if there is some documentation that answers
> what I am asking - I would be thrilled to read it. So far google has not
> helped me at all.
>
> This being said I need help with understanding what is going on here
> (full log):
>
>
> Oct 27 11:33:41 Arzamas kernel: ata6.00: exception Emask 0x10 SAct 0x0
> SErr 0x80000 action 0xe frozen
> Oct 27 11:33:41 Arzamas kernel: ata6.00: irq_stat 0x01100010, PHY RDY
> changed
> Oct 27 11:33:41 Arzamas kernel: ata6: SError: { 10B8B }
> Oct 27 11:33:41 Arzamas kernel: ata6.00: cmd
> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
> Oct 27 11:33:41 Arzamas kernel: res 06/37:00:00:00:00/00:00:00:00:06/00
> Emask 0x12 (ATA bus error)
> Oct 27 11:33:41 Arzamas kernel: ata6.00: error: { IDNF ABRT }
> Oct 27 11:33:41 Arzamas kernel: ata6: hard resetting link
> Oct 27 11:33:46 Arzamas kernel: ata6: SATA link up 3.0 Gbps (SStatus 123
> SControl 0)
> Oct 27 11:33:46 Arzamas kernel: ata6.00: configured for UDMA/100
> Oct 27 11:33:46 Arzamas kernel: ata6: EH complete
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] 488397168 512-byte
> hardware sectors (250059 MB)
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write Protect is off
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write cache: enabled,
> read cache: enabled, doesn't support DPO or FUA
> Oct 27 11:33:46 Arzamas kernel: end_request: I/O error, dev sde, sector
> 488166955
> Oct 27 11:33:46 Arzamas kernel: md: super_written gets error=-5, uptodate=0
> Oct 27 11:33:46 Arzamas kernel: raid10: Disk failure on sde2, disabling
> device.
> Oct 27 11:33:46 Arzamas kernel: raid10: Operation continuing on 3 devices.
> Oct 27 11:33:46 Arzamas kernel: RAID10 conf printout:
> Oct 27 11:33:46 Arzamas kernel: --- wd:3 rd:4
> Oct 27 11:33:46 Arzamas kernel: disk 0, wo:0, o:1, dev:sdc2
> Oct 27 11:33:46 Arzamas kernel: disk 1, wo:0, o:1, dev:sdb2
> Oct 27 11:33:46 Arzamas kernel: disk 2, wo:1, o:0, dev:sde2
> Oct 27 11:33:46 Arzamas kernel: disk 3, wo:0, o:1, dev:sdd2
> Oct 27 11:33:46 Arzamas kernel: RAID10 conf printout:
> Oct 27 11:33:46 Arzamas kernel: --- wd:3 rd:4
> Oct 27 11:33:46 Arzamas kernel: disk 0, wo:0, o:1, dev:sdc2
> Oct 27 11:33:46 Arzamas kernel: disk 1, wo:0, o:1, dev:sdb2
> Oct 27 11:33:46 Arzamas kernel: disk 3, wo:0, o:1, dev:sdd2
>
> Afterwards I removed sde from all arrays and mounts, and grilled it
> repeatedly with badblocks and smartctl -t long. Nothing came out for
> over a day. Below see the smartclt -a output. This happened one day
> after I upgraded to 2.6.27.4 from 2.6.23.
>
> Can someone please tell me what seems to be dying? Thank you!
Oct 27 11:33:46 Arzamas kernel: end_request: I/O error, dev sde, sector
488166955
Disk is going bad, I had the same problem, a week later, it was another I/O
error, a week after that, another I/O error, replace/RMA disk.
Justin.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-10-28 23:53 And again help on deciphering an error Peter Rabbitson
2008-10-29 8:08 ` Justin Piszcz
@ 2008-11-14 18:23 ` Peter Rabbitson
2008-11-14 19:57 ` Justin Piszcz
1 sibling, 1 reply; 11+ messages in thread
From: Peter Rabbitson @ 2008-11-14 18:23 UTC (permalink / raw)
To: linux-raid
Peter Rabbitson wrote:
> Hello,
>
> I need help with understanding what is going on here
> (full log):
>
>
> Oct 27 11:33:41 Arzamas kernel: ata6.00: exception Emask 0x10 SAct 0x0
> SErr 0x80000 action 0xe frozen
> Oct 27 11:33:41 Arzamas kernel: ata6.00: irq_stat 0x01100010, PHY RDY
> changed
> Oct 27 11:33:41 Arzamas kernel: ata6: SError: { 10B8B }
> Oct 27 11:33:41 Arzamas kernel: ata6.00: cmd
> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
> Oct 27 11:33:41 Arzamas kernel: res 06/37:00:00:00:00/00:00:00:00:06/00
> Emask 0x12 (ATA bus error)
> Oct 27 11:33:41 Arzamas kernel: ata6.00: error: { IDNF ABRT }
> Oct 27 11:33:41 Arzamas kernel: ata6: hard resetting link
> Oct 27 11:33:46 Arzamas kernel: ata6: SATA link up 3.0 Gbps (SStatus 123
> SControl 0)
> Oct 27 11:33:46 Arzamas kernel: ata6.00: configured for UDMA/100
> Oct 27 11:33:46 Arzamas kernel: ata6: EH complete
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] 488397168 512-byte
> hardware sectors (250059 MB)
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write Protect is off
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write cache: enabled,
> read cache: enabled, doesn't support DPO or FUA
> Oct 27 11:33:46 Arzamas kernel: end_request: I/O error, dev sde, sector
> 488166955
The saga continues. After replacing the drive (and I didn't make a
mistake as the serial numbers don't match) I got _exaclty_ the same
error a week later. I have replaced the cable for the drive in question,
will see what happens. The controller is:
02:03.0 Mass storage controller: Silicon Image, Inc. SiI 3124 PCI-X
Serial ATA Controller (rev 02)
Subsystem: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr+
Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 25
Region 0: Memory at fc5fd800 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fc5f0000 (64-bit, non-prefetchable) [size=32K]
Region 4: I/O ports at b000 [size=16]
Expansion ROM at fc480000 [disabled] [size=512K]
Capabilities: [64] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=12
Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048
DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: sata_sil24
Anyone has any bright ideas?
Thanks
New log follows:
Nov 8 15:41:18 Arzamas kernel: ata6.00: exception Emask 0x10 SAct 0x0
SErr 0x80000 action 0xe frozen
Nov 8 15:41:18 Arzamas kernel: ata6.00: irq_stat 0x01100010, PHY RDY
changed
Nov 8 15:41:18 Arzamas kernel: ata6: SError: { 10B8B }
Nov 8 15:41:18 Arzamas kernel: ata6.00: cmd
ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
Nov 8 15:41:18 Arzamas kernel: res 06/37:00:00:00:00/00:00:00:00:06/00
Emask 0x12 (ATA bus error)
Nov 8 15:41:18 Arzamas kernel: ata6.00: error: { IDNF ABRT }
Nov 8 15:41:18 Arzamas kernel: ata6: hard resetting link
Nov 8 15:41:22 Arzamas kernel: ata6: SATA link up 3.0 Gbps (SStatus 123
SControl 0)
Nov 8 15:41:22 Arzamas kernel: ata6.00: configured for UDMA/100
Nov 8 15:41:22 Arzamas kernel: ata6: EH complete
Nov 8 15:41:22 Arzamas kernel: sd 6:0:0:0: [sde] 488397168 512-byte
hardware sectors (250059 MB)
Nov 8 15:41:22 Arzamas kernel: sd 6:0:0:0: [sde] Write Protect is off
Nov 8 15:41:22 Arzamas kernel: sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
Nov 8 15:41:22 Arzamas kernel: sd 6:0:0:0: [sde] Write cache: enabled,
read cache: enabled, doesn't support DPO or FUA
Nov 8 15:41:22 Arzamas kernel: end_request: I/O error, dev sde, sector
488166955
Nov 8 15:41:22 Arzamas kernel: md: super_written gets error=-5, uptodate=0
Nov 8 15:41:22 Arzamas kernel: raid10: Disk failure on sde2, disabling
device.
Nov 8 15:41:22 Arzamas kernel: raid10: Operation continuing on 3 devices.
smartctl -a of new drive:
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Second Generation Serial ATA family
Device Model: WDC WD2500AAJS-08B4A0
Serial Number: WD-WMAT14036837
Firmware Version: 01.03A01
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Nov 14 13:22:23 2008 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (5580) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 68) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0027 174 174 021 Pre-fail Always
- 2266
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 9
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always
- 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 329
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 7
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always
- 6
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always
- 9
194 Temperature_Celsius 0x0022 106 103 000 Old_age Always
- 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 20
-
# 2 Extended offline Completed without error 00% 14
-
# 3 Short offline Completed without error 00% 1
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 18:23 ` And again help on deciphering an error (continued) Peter Rabbitson
@ 2008-11-14 19:57 ` Justin Piszcz
2008-11-14 20:01 ` Justin Piszcz
` (2 more replies)
0 siblings, 3 replies; 11+ messages in thread
From: Justin Piszcz @ 2008-11-14 19:57 UTC (permalink / raw)
To: Peter Rabbitson; +Cc: linux-raid
On Fri, 14 Nov 2008, Peter Rabbitson wrote:
> Peter Rabbitson wrote:
>> Hello,
>>
>> I need help with understanding what is going on here
>> (full log):
>>
>>
>> Oct 27 11:33:41 Arzamas kernel: ata6.00: exception Emask 0x10 SAct 0x0
>> SErr 0x80000 action 0xe frozen
>> Oct 27 11:33:41 Arzamas kernel: ata6.00: irq_stat 0x01100010, PHY RDY
>> changed
>> Oct 27 11:33:41 Arzamas kernel: ata6: SError: { 10B8B }
>> Oct 27 11:33:41 Arzamas kernel: ata6.00: cmd
>> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
>> Oct 27 11:33:41 Arzamas kernel: res 06/37:00:00:00:00/00:00:00:00:06/00
>> Emask 0x12 (ATA bus error)
>> Oct 27 11:33:41 Arzamas kernel: ata6.00: error: { IDNF ABRT }
>> Oct 27 11:33:41 Arzamas kernel: ata6: hard resetting link
>> Oct 27 11:33:46 Arzamas kernel: ata6: SATA link up 3.0 Gbps (SStatus 123
>> SControl 0)
>> Oct 27 11:33:46 Arzamas kernel: ata6.00: configured for UDMA/100
>> Oct 27 11:33:46 Arzamas kernel: ata6: EH complete
>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] 488397168 512-byte
>> hardware sectors (250059 MB)
>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write Protect is off
>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write cache: enabled,
>> read cache: enabled, doesn't support DPO or FUA
>> Oct 27 11:33:46 Arzamas kernel: end_request: I/O error, dev sde, sector
>> 488166955
>
> The saga continues. After replacing the drive (and I didn't make a
> mistake as the serial numbers don't match) I got _exaclty_ the same
> error a week later. I have replaced the cable for the drive in question,
> will see what happens. The controller is:
>
> 02:03.0 Mass storage controller: Silicon Image, Inc. SiI 3124 PCI-X
> Serial ATA Controller (rev 02)
> Subsystem: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr+
> Stepping+ SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 25
> Region 0: Memory at fc5fd800 (64-bit, non-prefetchable) [size=128]
> Region 2: Memory at fc5f0000 (64-bit, non-prefetchable) [size=32K]
> Region 4: I/O ports at b000 [size=16]
> Expansion ROM at fc480000 [disabled] [size=512K]
> Capabilities: [64] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [40] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=512 OST=12
> Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048
> DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
> Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
> Enable-
> Address: 0000000000000000 Data: 0000
> Kernel driver in use: sata_sil24
>
>
> Anyone has any bright ideas?
Hm, someone else also has similar problems, maybe we ought to buy new hw or
something, I have the same/similar issue as you.
BTW, after that error, if you re-run a short/long test, do they succeed or
hang (never complete)?
Justin.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 19:57 ` Justin Piszcz
@ 2008-11-14 20:01 ` Justin Piszcz
2008-11-14 20:06 ` Richard Scobie
2008-11-14 21:33 ` Peter Rabbitson
2 siblings, 0 replies; 11+ messages in thread
From: Justin Piszcz @ 2008-11-14 20:01 UTC (permalink / raw)
To: Peter Rabbitson; +Cc: linux-raid
On Fri, 14 Nov 2008, Justin Piszcz wrote:
>
>
> On Fri, 14 Nov 2008, Peter Rabbitson wrote:
>
>> Peter Rabbitson wrote:
>>> Hello,
>>>
>>> I need help with understanding what is going on here
>>> (full log):
>>>
>>>
>> Anyone has any bright ideas?
Here is the bugzilla URL he created:
https://bugzilla.redhat.com/show_bug.cgi?id=462425
What type of motherboard do you have?
I have that error and it occurs on sata_mv, Intel ICH8 and sil24, I don't
think its related to the card(s) themselves.
Justin.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 20:06 ` Richard Scobie
@ 2008-11-14 20:06 ` Justin Piszcz
2008-11-14 20:12 ` Justin Piszcz
0 siblings, 1 reply; 11+ messages in thread
From: Justin Piszcz @ 2008-11-14 20:06 UTC (permalink / raw)
To: Richard Scobie; +Cc: Peter Rabbitson, linux-raid, linux-ide
On Sat, 15 Nov 2008, Richard Scobie wrote:
> Justin Piszcz wrote:
>>
>>
>> On Fri, 14 Nov 2008, Peter Rabbitson wrote:
>>
>>> Peter Rabbitson wrote:
>>>
>>>> Hello,
>>>>
>>>> I need help with understanding what is going on here
>>>> (full log):
>
> These posts might be worth sending to linux-ide.
>
> Regards,
>
> Richard
>
I have a whole bunch, but here is the last one:
[64894.610696] ata9.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[64894.610703] ata9.00: irq_stat 0x00020002, device error via D2H FIS
[64894.610708] ata9.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[64894.610709] res 51/04:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x1 (devic
e error)
[64894.610714] ata9.00: status: { DRDY ERR }
[64894.610718] ata9.00: error: { ABRT }
[64894.626437] ata9.00: configured for UDMA/100
[64894.626449] ata9: EH complete
[64894.626654] sd 8:0:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
[64894.637744] end_request: I/O error, dev sdh, sector 586067135
[64894.637759] md: super_written gets error=-5, uptodate=0
[64894.637762] raid5: Disk failure on sdh1, disabling device.
[64894.637763] raid5: Operation continuing on 9 devices.
[64894.638129] sd 8:0:0:0: [sdh] Write Protect is off
[64894.638131] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[64894.638148] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, does
n't support DPO or FUA
Justin.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 19:57 ` Justin Piszcz
2008-11-14 20:01 ` Justin Piszcz
@ 2008-11-14 20:06 ` Richard Scobie
2008-11-14 20:06 ` Justin Piszcz
2008-11-14 21:33 ` Peter Rabbitson
2 siblings, 1 reply; 11+ messages in thread
From: Richard Scobie @ 2008-11-14 20:06 UTC (permalink / raw)
To: Justin Piszcz; +Cc: Peter Rabbitson, linux-raid
Justin Piszcz wrote:
>
>
> On Fri, 14 Nov 2008, Peter Rabbitson wrote:
>
>> Peter Rabbitson wrote:
>>
>>> Hello,
>>>
>>> I need help with understanding what is going on here
>>> (full log):
These posts might be worth sending to linux-ide.
Regards,
Richard
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 20:06 ` Justin Piszcz
@ 2008-11-14 20:12 ` Justin Piszcz
2008-11-15 3:53 ` Robert Hancock
0 siblings, 1 reply; 11+ messages in thread
From: Justin Piszcz @ 2008-11-14 20:12 UTC (permalink / raw)
To: Richard Scobie; +Cc: Peter Rabbitson, linux-raid, linux-ide
On Fri, 14 Nov 2008, Justin Piszcz wrote:
>
>
> On Sat, 15 Nov 2008, Richard Scobie wrote:
>
>> Justin Piszcz wrote:
>>>
>>>
>>> On Fri, 14 Nov 2008, Peter Rabbitson wrote:
>>>
>>>> Peter Rabbitson wrote:
>>>>
>>>>> Hello,
>>>>>
>>>>> I need help with understanding what is going on here
>>>>> (full log):
>>
>> These posts might be worth sending to linux-ide.
>>
>> Regards,
>>
>> Richard
>>
>
> I have a whole bunch, but here is the last one:
Here are some more:
Jul 14 05:54:55 p34 kernel: [478107.751877] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Jul 14 05:54:55 p34 kernel: [478107.751883] ata4.00: irq_stat 0x40000001
Jul 14 05:54:55 p34 kernel: [478107.751889] ata4.00: cmd 25/00:f8:08:b0:ee/00:00:22:00:00/e0 tag 0 dma 126976 in
Jul 14 05:54:55 p34 kernel: [478107.751890] res 51/40:f8:47:b0:ee/00:00:22:00:00/e0 Emask 0x9 (media error)
Jul 14 05:54:55 p34 kernel: [478107.751895] ata4.00: status: { DRDY ERR }
Jul 14 05:54:55 p34 kernel: [478107.751898] ata4.00: error: { UNC }
Jul 14 05:54:55 p34 kernel: [478107.773836] ata4.00: configured for UDMA/133
Jul 14 05:54:55 p34 kernel: [478107.773845] ata4: EH complete
Jul 14 05:54:55 p34 kernel: [478107.844912] sd 3:0:0:0: [sdd] 586072368 512-byte hardware sectors (300069 MB)
Jul 14 05:54:55 p34 kernel: [478107.846321] sd 3:0:0:0: [sdd] Write Protect is off
Jul 14 05:54:55 p34 kernel: [478107.846325] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Jul 14 05:54:55 p34 kernel: [478107.849297] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 12 09:25:22 p34 kernel: [1434196.959129] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Oct 12 09:25:30 p34 kernel: [1434196.959137] ata6.00: irq_stat 0x40000001
Oct 12 09:25:30 p34 kernel: [1434196.959142] ata6.00: cmd 25/00:00:00:af:ee/00:02:22:00:00/e0 tag 0 dma 262144 in
Oct 12 09:25:30 p34 kernel: [1434196.959144] res 51/40:00:4f:b0:ee/00:02:22:00:00/e0 Emask 0x9 (media error)
Oct 12 09:25:30 p34 kernel: [1434196.959149] ata6.00: status: { DRDY ERR }
Oct 12 09:25:30 p34 kernel: [1434196.959152] ata6.00: error: { UNC }
Oct 12 09:25:30 p34 kernel: [1434196.999110] ata6.00: configured for UDMA/133
Oct 12 09:25:30 p34 kernel: [1434196.999144] ata6: EH complete
Oct 12 09:25:30 p34 kernel: [1434203.096157] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Oct 12 09:25:30 p34 kernel: [1434203.096165] ata6.00: irq_stat 0x40000001
Oct 12 09:25:30 p34 kernel: [1434203.096171] ata6.00: cmd 25/00:00:00:af:ee/00:02:22:00:00/e0 tag 0 dma 262144 in
Oct 12 09:25:30 p34 kernel: [1434203.096172] res 51/40:00:4f:b0:ee/00:02:22:00:00/e0 Emask 0x9 (media error)
Oct 12 09:25:30 p34 kernel: [1434203.096177] ata6.00: status: { DRDY ERR }
Oct 12 09:25:30 p34 kernel: [1434203.096181] ata6.00: error: { UNC }
Oct 12 09:25:30 p34 kernel: [1434203.104811] ata6.00: configured for UDMA/133
Oct 12 09:25:30 p34 kernel: [1434203.104819] ata6: EH complete
Nov 9 09:25:19 p34 kernel: [ 3686.460568] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Nov 9 09:25:19 p34 kernel: [ 3686.460574] ata4.00: irq_stat 0x40000001
Nov 9 09:25:19 p34 kernel: [ 3686.460579] ata4.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
Nov 9 09:25:19 p34 kernel: [ 3686.460580] res 51/10:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x81 (invalid argument)
Nov 9 09:25:19 p34 kernel: [ 3686.460585] ata4.00: status: { DRDY ERR }
Nov 9 09:25:19 p34 kernel: [ 3686.460589] ata4.00: error: { IDNF }
Nov 9 09:25:24 p34 kernel: [ 3691.461173] ata4.00: qc timeout (cmd 0xec)
Nov 9 09:25:24 p34 kernel: [ 3691.461183] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x5)
Nov 9 09:25:24 p34 kernel: [ 3691.461187] ata4.00: revalidation failed (errno=-5)
Nov 9 09:25:24 p34 kernel: [ 3691.461192] ata4: hard resetting link
Nov 9 09:25:24 p34 kernel: [ 3691.766178] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Nov 9 09:25:24 p34 kernel: [ 3691.803834] ata4.00: configured for UDMA/133
Nov 9 09:25:24 p34 kernel: [ 3691.803846] end_request: I/O error, dev sdd, sector 586067135
Nov 9 09:25:24 p34 kernel: [ 3691.803849] md: super_written gets error=-5, uptodate=0
Nov 9 09:25:24 p34 kernel: [ 3691.803853] raid5: Disk failure on sdd1, disabling device.
Nov 9 09:25:24 p34 kernel: [ 3691.803854] raid5: Operation continuing on 8 devices.
Nov 12 01:22:28 p34 kernel: [64894.610696] ata9.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Nov 12 01:22:28 p34 kernel: [64894.610703] ata9.00: irq_stat 0x00020002, device error via D2H FIS
Nov 12 01:22:28 p34 kernel: [64894.610708] ata9.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
Nov 12 01:22:28 p34 kernel: [64894.610709] res 51/04:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x1 (device error)
Nov 12 01:22:28 p34 kernel: [64894.610714] ata9.00: status: { DRDY ERR }
Nov 12 01:22:28 p34 kernel: [64894.610718] ata9.00: error: { ABRT }
Nov 12 01:22:28 p34 kernel: [64894.626437] ata9.00: configured for UDMA/100
Nov 12 01:22:28 p34 kernel: [64894.626449] ata9: EH complete
Nov 12 01:22:28 p34 kernel: [64894.626654] sd 8:0:0:0: [sdh] 586072368 512-byte hardware sectors (300069 MB)
Nov 12 01:22:28 p34 kernel: [64894.637744] end_request: I/O error, dev sdh, sector 586067135
Nov 12 01:22:28 p34 kernel: [64894.637759] md: super_written gets error=-5, uptodate=0
Nov 12 01:22:28 p34 kernel: [64894.637762] raid5: Disk failure on sdh1, disabling device.
Nov 12 01:22:28 p34 kernel: [64894.637763] raid5: Operation continuing on 9 devices.
Nov 12 01:22:28 p34 kernel: [64894.638129] sd 8:0:0:0: [sdh] Write Protect is off
Nov 12 01:22:28 p34 kernel: [64894.638131] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
Nov 12 01:22:28 p34 kernel: [64894.638148] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 19:57 ` Justin Piszcz
2008-11-14 20:01 ` Justin Piszcz
2008-11-14 20:06 ` Richard Scobie
@ 2008-11-14 21:33 ` Peter Rabbitson
2 siblings, 0 replies; 11+ messages in thread
From: Peter Rabbitson @ 2008-11-14 21:33 UTC (permalink / raw)
To: Justin Piszcz; +Cc: linux-raid, linux-ide
Justin Piszcz wrote:
>
>
> On Fri, 14 Nov 2008, Peter Rabbitson wrote:
>
>> Peter Rabbitson wrote:
>>> Hello,
>>>
>>> I need help with understanding what is going on here
>>> (full log):
>>>
>>>
>>> Oct 27 11:33:41 Arzamas kernel: ata6.00: exception Emask 0x10 SAct 0x0
>>> SErr 0x80000 action 0xe frozen
>>> Oct 27 11:33:41 Arzamas kernel: ata6.00: irq_stat 0x01100010, PHY RDY
>>> changed
>>> Oct 27 11:33:41 Arzamas kernel: ata6: SError: { 10B8B }
>>> Oct 27 11:33:41 Arzamas kernel: ata6.00: cmd
>>> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
>>> Oct 27 11:33:41 Arzamas kernel: res 06/37:00:00:00:00/00:00:00:00:06/00
>>> Emask 0x12 (ATA bus error)
>>> Oct 27 11:33:41 Arzamas kernel: ata6.00: error: { IDNF ABRT }
>>> Oct 27 11:33:41 Arzamas kernel: ata6: hard resetting link
>>> Oct 27 11:33:46 Arzamas kernel: ata6: SATA link up 3.0 Gbps (SStatus 123
>>> SControl 0)
>>> Oct 27 11:33:46 Arzamas kernel: ata6.00: configured for UDMA/100
>>> Oct 27 11:33:46 Arzamas kernel: ata6: EH complete
>>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] 488397168 512-byte
>>> hardware sectors (250059 MB)
>>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write Protect is off
>>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Mode Sense: 00 3a
>>> 00 00
>>> Oct 27 11:33:46 Arzamas kernel: sd 6:0:0:0: [sde] Write cache: enabled,
>>> read cache: enabled, doesn't support DPO or FUA
>>> Oct 27 11:33:46 Arzamas kernel: end_request: I/O error, dev sde, sector
>>> 488166955
>>
>> The saga continues. After replacing the drive (and I didn't make a
>> mistake as the serial numbers don't match) I got _exaclty_ the same
>> error a week later. I have replaced the cable for the drive in question,
>> will see what happens. The controller is:
>>
>> 02:03.0 Mass storage controller: Silicon Image, Inc. SiI 3124 PCI-X
>> Serial ATA Controller (rev 02)
>> Subsystem: Silicon Image, Inc. SiI 3124 PCI-X Serial ATA Controller
>> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr+
>> Stepping+ SERR+ FastB2B- DisINTx-
>> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
>> <TAbort- <MAbort- >SERR- <PERR- INTx-
>> Latency: 64, Cache Line Size: 64 bytes
>> Interrupt: pin A routed to IRQ 25
>> Region 0: Memory at fc5fd800 (64-bit, non-prefetchable) [size=128]
>> Region 2: Memory at fc5f0000 (64-bit, non-prefetchable) [size=32K]
>> Region 4: I/O ports at b000 [size=16]
>> Expansion ROM at fc480000 [disabled] [size=512K]
>> Capabilities: [64] Power Management version 2
>> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
>> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>> Capabilities: [40] PCI-X non-bridge device
>> Command: DPERE- ERO+ RBC=512 OST=12
>> Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple
>> DMMRBC=2048
>> DMOST=12 DMCRS=128 RSCEM- 266MHz- 533MHz-
>> Capabilities: [54] Message Signalled Interrupts: Mask- 64bit+
>> Queue=0/0
>> Enable-
>> Address: 0000000000000000 Data: 0000
>> Kernel driver in use: sata_sil24
>>
>>
>> Anyone has any bright ideas?
>
> Hm, someone else also has similar problems, maybe we ought to buy new hw or
> something, I have the same/similar issue as you.
>
> BTW, after that error, if you re-run a short/long test, do they succeed or
> hang (never complete)?
>
They succeed with flying colors. Moreover I had badblocks -svw running
at the same time (so the drive was really loaded). And I did this
repeatedly with the first one - no issues.
Peter
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-14 20:12 ` Justin Piszcz
@ 2008-11-15 3:53 ` Robert Hancock
2008-11-15 8:37 ` Peter Rabbitson
0 siblings, 1 reply; 11+ messages in thread
From: Robert Hancock @ 2008-11-15 3:53 UTC (permalink / raw)
To: linux-raid; +Cc: linux-ide
Justin Piszcz wrote:
> Here are some more:
>
> Jul 14 05:54:55 p34 kernel: [478107.751877] ata4.00: exception Emask 0x0
> SAct 0x0 SErr 0x0 action 0x0
> Jul 14 05:54:55 p34 kernel: [478107.751883] ata4.00: irq_stat 0x40000001
> Jul 14 05:54:55 p34 kernel: [478107.751889] ata4.00: cmd
> 25/00:f8:08:b0:ee/00:00:22:00:00/e0 tag 0 dma 126976 in
> Jul 14 05:54:55 p34 kernel: [478107.751890] res
> 51/40:f8:47:b0:ee/00:00:22:00:00/e0 Emask 0x9 (media error)
> Jul 14 05:54:55 p34 kernel: [478107.751895] ata4.00: status: { DRDY ERR }
> Jul 14 05:54:55 p34 kernel: [478107.751898] ata4.00: error: { UNC }
Drive reporting an uncorrectable error on a read command.
> Nov 9 09:25:19 p34 kernel: [ 3686.460568] ata4.00: exception Emask 0x0
> SAct 0x0 SErr 0x0 action 0x0
> Nov 9 09:25:19 p34 kernel: [ 3686.460574] ata4.00: irq_stat 0x40000001
> Nov 9 09:25:19 p34 kernel: [ 3686.460579] ata4.00: cmd
> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
> Nov 9 09:25:19 p34 kernel: [ 3686.460580] res
> 51/10:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x81 (invalid argument)
> Nov 9 09:25:19 p34 kernel: [ 3686.460585] ata4.00: status: { DRDY ERR }
> Nov 9 09:25:19 p34 kernel: [ 3686.460589] ata4.00: error: { IDNF }
Flush cache returned ID not found (drive couldn't find a sector)
> Nov 9 09:25:24 p34 kernel: [ 3691.461173] ata4.00: qc timeout (cmd 0xec)
> Nov 9 09:25:24 p34 kernel: [ 3691.461183] ata4.00: failed to IDENTIFY
> (I/O error, err_mask=0x5)
> Nov 9 09:25:24 p34 kernel: [ 3691.461187] ata4.00: revalidation failed
> (errno=-5)
> Nov 9 09:25:24 p34 kernel: [ 3691.461192] ata4: hard resetting link
> Nov 9 09:25:24 p34 kernel: [ 3691.766178] ata4: SATA link up 3.0 Gbps
> (SStatus 123 SControl 300)
> Nov 9 09:25:24 p34 kernel: [ 3691.803834] ata4.00: configured for UDMA/133
> Nov 9 09:25:24 p34 kernel: [ 3691.803846] end_request: I/O error, dev
> sdd, sector 586067135
> Nov 9 09:25:24 p34 kernel: [ 3691.803849] md: super_written gets
> error=-5, uptodate=0
> Nov 9 09:25:24 p34 kernel: [ 3691.803853] raid5: Disk failure on sdd1,
> disabling device.
> Nov 9 09:25:24 p34 kernel: [ 3691.803854] raid5: Operation continuing
> on 8 devices.
>
> Nov 12 01:22:28 p34 kernel: [64894.610696] ata9.00: exception Emask 0x0
> SAct 0x0 SErr 0x0 action 0x0
> Nov 12 01:22:28 p34 kernel: [64894.610703] ata9.00: irq_stat 0x00020002,
> device error via D2H FIS
> Nov 12 01:22:28 p34 kernel: [64894.610708] ata9.00: cmd
> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
> Nov 12 01:22:28 p34 kernel: [64894.610709] res
> 51/04:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x1 (device error)
> Nov 12 01:22:28 p34 kernel: [64894.610714] ata9.00: status: { DRDY ERR }
> Nov 12 01:22:28 p34 kernel: [64894.610718] ata9.00: error: { ABRT }
Flush cache returned command aborted, presumably because the write to
media failed.
Looks like some sick drives, or some other more global problem (power,
temperature, etc.) to me..
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: And again help on deciphering an error (continued)
2008-11-15 3:53 ` Robert Hancock
@ 2008-11-15 8:37 ` Peter Rabbitson
0 siblings, 0 replies; 11+ messages in thread
From: Peter Rabbitson @ 2008-11-15 8:37 UTC (permalink / raw)
To: Robert Hancock; +Cc: linux-raid, linux-ide
Robert Hancock wrote:
> Justin Piszcz wrote:
>> Here are some more:
>>
>> Jul 14 05:54:55 p34 kernel: [478107.751877] ata4.00: exception Emask
>> 0x0 SAct 0x0 SErr 0x0 action 0x0
>> Jul 14 05:54:55 p34 kernel: [478107.751883] ata4.00: irq_stat 0x40000001
>> Jul 14 05:54:55 p34 kernel: [478107.751889] ata4.00: cmd
>> 25/00:f8:08:b0:ee/00:00:22:00:00/e0 tag 0 dma 126976 in
>> Jul 14 05:54:55 p34 kernel: [478107.751890] res
>> 51/40:f8:47:b0:ee/00:00:22:00:00/e0 Emask 0x9 (media error)
>> Jul 14 05:54:55 p34 kernel: [478107.751895] ata4.00: status: { DRDY ERR }
>> Jul 14 05:54:55 p34 kernel: [478107.751898] ata4.00: error: { UNC }
>
> Drive reporting an uncorrectable error on a read command.
>
>> Nov 9 09:25:19 p34 kernel: [ 3686.460568] ata4.00: exception Emask
>> 0x0 SAct 0x0 SErr 0x0 action 0x0
>> Nov 9 09:25:19 p34 kernel: [ 3686.460574] ata4.00: irq_stat 0x40000001
>> Nov 9 09:25:19 p34 kernel: [ 3686.460579] ata4.00: cmd
>> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
>> Nov 9 09:25:19 p34 kernel: [ 3686.460580] res
>> 51/10:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x81 (invalid argument)
>> Nov 9 09:25:19 p34 kernel: [ 3686.460585] ata4.00: status: { DRDY ERR }
>> Nov 9 09:25:19 p34 kernel: [ 3686.460589] ata4.00: error: { IDNF }
>
> Flush cache returned ID not found (drive couldn't find a sector)
>
>> Nov 9 09:25:24 p34 kernel: [ 3691.461173] ata4.00: qc timeout (cmd 0xec)
>> Nov 9 09:25:24 p34 kernel: [ 3691.461183] ata4.00: failed to IDENTIFY
>> (I/O error, err_mask=0x5)
>> Nov 9 09:25:24 p34 kernel: [ 3691.461187] ata4.00: revalidation
>> failed (errno=-5)
>> Nov 9 09:25:24 p34 kernel: [ 3691.461192] ata4: hard resetting link
>> Nov 9 09:25:24 p34 kernel: [ 3691.766178] ata4: SATA link up 3.0 Gbps
>> (SStatus 123 SControl 300)
>> Nov 9 09:25:24 p34 kernel: [ 3691.803834] ata4.00: configured for
>> UDMA/133
>> Nov 9 09:25:24 p34 kernel: [ 3691.803846] end_request: I/O error, dev
>> sdd, sector 586067135
>> Nov 9 09:25:24 p34 kernel: [ 3691.803849] md: super_written gets
>> error=-5, uptodate=0
>> Nov 9 09:25:24 p34 kernel: [ 3691.803853] raid5: Disk failure on
>> sdd1, disabling device.
>> Nov 9 09:25:24 p34 kernel: [ 3691.803854] raid5: Operation continuing
>> on 8 devices.
>>
>> Nov 12 01:22:28 p34 kernel: [64894.610696] ata9.00: exception Emask
>> 0x0 SAct 0x0 SErr 0x0 action 0x0
>> Nov 12 01:22:28 p34 kernel: [64894.610703] ata9.00: irq_stat
>> 0x00020002, device error via D2H FIS
>> Nov 12 01:22:28 p34 kernel: [64894.610708] ata9.00: cmd
>> ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
>> Nov 12 01:22:28 p34 kernel: [64894.610709] res
>> 51/04:00:34:cf:f3/00:00:00:f3:40/a3 Emask 0x1 (device error)
>> Nov 12 01:22:28 p34 kernel: [64894.610714] ata9.00: status: { DRDY ERR }
>> Nov 12 01:22:28 p34 kernel: [64894.610718] ata9.00: error: { ABRT }
>
> Flush cache returned command aborted, presumably because the write to
> media failed.
>
> Looks like some sick drives, or some other more global problem (power,
> temperature, etc.) to me..
>
But an _identical_ sector number? Looks too unlikely... I might try to
crank open hexedit and write repeatedly to this place. Sectors are still
512 bytes right?
Peter
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2008-11-15 8:37 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-10-28 23:53 And again help on deciphering an error Peter Rabbitson
2008-10-29 8:08 ` Justin Piszcz
2008-11-14 18:23 ` And again help on deciphering an error (continued) Peter Rabbitson
2008-11-14 19:57 ` Justin Piszcz
2008-11-14 20:01 ` Justin Piszcz
2008-11-14 20:06 ` Richard Scobie
2008-11-14 20:06 ` Justin Piszcz
2008-11-14 20:12 ` Justin Piszcz
2008-11-15 3:53 ` Robert Hancock
2008-11-15 8:37 ` Peter Rabbitson
2008-11-14 21:33 ` Peter Rabbitson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).