From mboxrd@z Thu Jan 1 00:00:00 1970 From: Bill Davidsen Subject: Re: array always resyncs on boot Date: Mon, 01 Dec 2008 12:46:09 -0500 Message-ID: <493422E1.8080207@tmr.com> References: <4931B2C5.5060403@openhardware.net> <4931E75D.5080905@openhardware.net> Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: <4931E75D.5080905@openhardware.net> Sender: linux-raid-owner@vger.kernel.org To: Tom Walsh Cc: linux-raid@vger.kernel.org List-Id: linux-raid.ids Tom Walsh wrote: > Justin Piszcz wrote: >> > >>> I just cannot keep the system from resyncing on every boot. I've >>> gotten to the point that I'm thinking that I may have been root'ed and >>> the boot flash of the drives has been reflashed... Ok, that is >>> reaching for an answer, I know. This is time to ask for help. help! >> >> If you boot knoppix and manually assemble the array does it assemble >> cleanly >> or does it need a resync as well? >> > > Well, I used my last CD-R on the WD Data Lifeguard. But, I think I > know what you are driving at. Booting Mandriva 2009 into Rescue mode, > then choosing "Mount your partitions under mnt" does cleanly start the > array. > > Following that further, I booted off /dev/sda1 (where my small > Mandriva system is currently installed), then I disabled the mdadm > service in /etc/init.d/. I then waited for the system to do the > resync and rebooted the system. Then logged into the system. > Just for grins, could you post the partition table for each disk? Maybe just the output of "fdisk -l" to show everything? I always worry when using drives of "almost" the same size. > At this point, I have had a message from dmesg stating that the raid > array is resync-ing. This is mdadm -D --scan from before and after > reboot, and shows before and after mdstat: > > ================================================================= > /dev/md0: > Version : 00.90 > Creation Time : Sat Nov 29 09:34:45 2008 > Raid Level : raid10 > Array Size : 62942208 (60.03 GiB 64.45 GB) > Used Dev Size : 20980736 (20.01 GiB 21.48 GB) > Raid Devices : 6 > Total Devices : 6 > Preferred Minor : 0 > Persistence : Superblock is persistent > > Update Time : Sat Nov 29 19:45:43 2008 > State : clean > Active Devices : 6 > Working Devices : 6 > Failed Devices : 0 > Spare Devices : 0 > > Layout : near=2, far=1 > Chunk Size : 64K > > UUID : cc05dcc8:b5192714:033ef1ee:62f617b8 > Events : 0.42 > > Number Major Minor RaidDevice State > 0 8 5 0 active sync /dev/sda5 > 1 8 21 1 active sync /dev/sdb5 > 2 8 37 2 active sync /dev/sdc5 > 3 8 53 3 active sync /dev/sdd5 > 4 8 69 4 active sync /dev/sde5 > 5 8 85 5 active sync /dev/sdf5 > /dev/md0: > Version : 00.90 > Creation Time : Sat Nov 29 09:34:45 2008 > Raid Level : raid10 > Array Size : 62942208 (60.03 GiB 64.45 GB) > Used Dev Size : 20980736 (20.01 GiB 21.48 GB) > Raid Devices : 6 > Total Devices : 6 > Preferred Minor : 0 > Persistence : Superblock is persistent > > Update Time : Sat Nov 29 19:47:03 2008 > State : clean, degraded, recovering > Active Devices : 5 > Working Devices : 6 > Failed Devices : 0 > Spare Devices : 1 > > Layout : near=2, far=1 > Chunk Size : 64K > > Rebuild Status : 4% complete > > UUID : cc05dcc8:b5192714:033ef1ee:62f617b8 > Events : 0.44 > > Number Major Minor RaidDevice State > 0 8 5 0 active sync /dev/sda5 > 1 8 21 1 active sync /dev/sdb5 > 2 8 37 2 active sync /dev/sdc5 > 6 8 53 3 spare rebuilding /dev/sdd5 > 4 8 69 4 active sync /dev/sde5 > 5 8 85 5 active sync /dev/sdf5 > > > Personalities : [raid10] > md0 : active raid10 sdd5[6] sdc5[2] sda5[0] sdb5[1] sde5[4] sdf5[5] > 62942208 blocks 64K chunks 2 near-copies [6/5] [UUU_UU] > [===============>.....] recovery = 76.2% (15994624/20980736) > finish=1.4min speed=56416K/sec > > unused devices: > > > Personalities : [raid10] > md0 : active raid10 sdd5[3] sdc5[2] sda5[0] sdb5[1] sde5[4] sdf5[5] > 62942208 blocks 64K chunks 2 near-copies [6/6] [UUUUUU] > > unused devices: > ================================================================= > > > > >> Also: >>> mdadm -Eb /dev/sda5 >> /etc/mdadm >>> blkid /dev/md0 >> /etc/fstab >> >> I never use these commands? >> >> I take the output of: >> # mdadm --examine --scan >> >> And add it to /etc/mdadm/mdadm.conf. >> >> And then add /dev/md0 /mnt xfs etc into /etc/fstab. > > Right, same result, differing approach. mdadm -Eb will also > give the UUID in a brief string. > >> >> In addition I don't use a > 0.90 superblock (not saying thats the >> problem but just noting a difference) >> >> mdadm --create /dev/md3 -e 0.90 --assume-clean --level=5 --chunk=1024 >> --verbose --raid-devices=10 /dev/sdc1 /dev/sdd1 /dev/sde1 /dev/sdf1 >> missing /dev/sdh1 /dev/sdi1 /dev/sdj1 /dev/sdk1 /dev/sdl1 >> >> Besides that though the commands look the same. > > Yes, superblock is a version 0.90 and I cleared them via: > mdadm --zero-supderblock --force /dev/sd[a-f]5 > > From what I've googled, the --zero-superblock will remove any > superblock from front or back of the partition. --force will insist > that the operation be done even if it doesn't look like a superblock > exists. > > >> >> Do you use initrd/etc or do you compile everything in at the kernel >> level? >> Is it possible one disk is on one controller and the others are on >> another >> or something weird like that, such that the driver for one chipset loads >> before and the other does not load until later? >> >> Some dmesg output may be useful along with mdadm -D on the raid array >> before and after reboots. >> > > dmesg (/var/log/messages as well) are mysteriously quiet about why the > resync was initiated, they merely state that it is being done. That > what is driving me nuts, no log info. This is an ICH10 system board > (Gigabyte GA-EP43-DS3L), the other board was Asus P5N-T Deluxe, also > an ICH10 chipset. This is the dmesg output from the recent Gigabyte > board boot (and resync): > > Linux version 2.6.27.7 (root@localhost) (gcc version 4.3.2 (GCC) ) #1 > SMP Sat Nov 29 10:14:42 EST 2008 > Command line: BOOT_IMAGE=linux root=801 quiet > KERNEL supported cpus: > Intel GenuineIntel > AMD AuthenticAMD > Centaur CentaurHauls > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000007fee0000 (usable) > BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS) > BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data) > BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved) > BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved) > BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) > DMI 2.4 present. > last_pfn = 0x7fee0 max_arch_pfn = 0x3ffffffff > x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 > init_memory_mapping > 0000000000 - 007fe00000 page 2M > 007fe00000 - 007fee0000 page 4k > kernel direct mapping tables up to 7fee0000 @ 8000-c000 > last_map_addr: 7fee0000 end: 7fee0000 > RAMDISK: 03d1e000 - 040efe24 > ACPI: RSDP 000F70C0, 0014 (r0 GBT ) > ACPI: RSDT 7FEE3040, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) > ACPI: FACP 7FEE30C0, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) > ACPI: DSDT 7FEE3180, 4B8A (r1 GBT GBTUACPI 1000 MSFT 100000C) > ACPI: FACS 7FEE0000, 0040 > ACPI: HPET 7FEE7E80, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98) > ACPI: MCFG 7FEE7F00, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) > ACPI: APIC 7FEE7D80, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) > ACPI: SSDT 7FEE8860, 03AB (r1 PmRef CpuPm 3000 INTL 20040311) > No NUMA configuration found > Faking a node at 0000000000000000-000000007fee0000 > Bootmem setup node 0 0000000000000000-000000007fee0000 > NODE_DATA [0000000000001000 - 0000000000005fff] > bootmap [000000000000a000 - 0000000000019fdf] pages 10 > (6 early reservations) ==> bootmem [0000000000 - 007fee0000] > #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - > 0000001000] > #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - > 0000008000] > #2 [0000200000 - 00007ca68c] TEXT DATA BSS ==> [0000200000 - > 00007ca68c] > #3 [0003d1e000 - 00040efe24] RAMDISK ==> [0003d1e000 - > 00040efe24] > #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - > 0000100000] > #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - > 000000a000] > found SMP MP-table at [ffff8800000f56d0] 000f56d0 > [ffffe20000000000-ffffe20001bfffff] PMD -> > [ffff880001200000-ffff880002dfffff] on node 0 > Zone PFN ranges: > DMA 0x00000000 -> 0x00001000 > DMA32 0x00001000 -> 0x00100000 > Normal 0x00100000 -> 0x00100000 > Movable zone start PFN for each node > early_node_map[2] active PFN ranges > 0: 0x00000000 -> 0x0000009f > 0: 0x00000100 -> 0x0007fee0 > On node 0 totalpages: 523903 > DMA zone: 2358 pages, LIFO batch:0 > DMA32 zone: 512795 pages, LIFO batch:31 > ACPI: PM-Timer IO Port: 0x408 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) > ACPI: LAPIC (acpi_id[0x02] lapic_id[0x03] enabled) > ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled) > ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) > ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) > ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) > ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) > ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > ACPI: IRQ0 used by override. > ACPI: IRQ2 used by override. > ACPI: IRQ9 used by override. > Setting APIC routing to flat > ACPI: HPET id: 0x8086a201 base: 0xfed00000 > Using ACPI (MADT) for SMP configuration information > SMP: Allowing 4 CPUs, 0 hotplug CPUs > PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 > PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 > PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 > Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000) > PERCPU: Allocating 51744 bytes of per cpu data > NR_CPUS: 32, nr_cpu_ids: 4, nr_node_ids 1 > Built 1 zonelists in Node order, mobility grouping on. Total pages: > 515153 > Policy zone: DMA32 > Kernel command line: BOOT_IMAGE=linux root=801 quiet > Initializing CPU#0 > PID hash table entries: 4096 (order: 12, 32768 bytes) > TSC: PIT calibration confirmed by PMTIMER. > TSC: using PMTIMER calibration value > Detected 2400.073 MHz processor. > Console: colour VGA+ 80x25 > console [tty0] enabled > Checking aperture... > No AGP bridge found > Calgary: detecting Calgary via BIOS EBDA area > Calgary: Unable to locate Rio Grande table in EBDA - bailing! > Memory: 2056720k/2096000k available (2973k kernel code, 38892k > reserved, 1521k data, 532k init) > CPA: page pool initialized 1 of 1 pages preallocated > SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 > hpet clockevent registered > Calibrating delay loop (skipped), value calculated using timer > frequency.. 4800.14 BogoMIPS (lpj=2400073) > Security Framework initialized > Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) > Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) > Mount-cache hash table entries: 256 > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > CPU 0/0 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 0 > CPU0: Thermal monitoring enabled (TM2) > using mwait in idle threads. > ACPI: Core revision 20080609 > ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 > CPU0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b > Using local APIC timer interrupts. > APIC timer calibration result 16667158 > Detected 16.667 MHz APIC timer. > Booting processor 1/2 ip 6000 > Initializing CPU#1 > Calibrating delay using timer specific routine.. 4800.18 BogoMIPS > (lpj=2400090) > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > CPU 1/2 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 2 > CPU1: Thermal monitoring enabled (TM2) > x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 > CPU1: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b > checking TSC synchronization [CPU#0 -> CPU#1]: passed. > Booting processor 2/3 ip 6000 > Initializing CPU#2 > Calibrating delay using timer specific routine.. 4864.63 BogoMIPS > (lpj=2432315) > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > CPU 2/3 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 3 > CPU2: Thermal monitoring enabled (TM2) > x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106 > CPU2: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b > checking TSC synchronization [CPU#0 -> CPU#2]: passed. > Booting processor 3/1 ip 6000 > Initializing CPU#3 > Calibrating delay using timer specific routine.. 4799.69 BogoMIPS > (lpj=2399847) > CPU: L1 I cache: 32K, L1 D cache: 32K > CPU: L2 cache: 4096K > CPU 3/1 -> Node 0 > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > CPU3: Thermal monitoring enabled (TM2) > x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106 > CPU3: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz stepping 0b > checking TSC synchronization [CPU#0 -> CPU#3]: passed. > Brought up 4 CPUs > Total of 4 processors activated (19264.65 BogoMIPS). > CPU0 attaching sched-domain: > domain 0: span 0,3 level MC > groups: 0 3 > domain 1: span 0-3 level CPU > groups: 0,3 1-2 > domain 2: span 0-3 level NODE > groups: 0-3 > CPU1 attaching sched-domain: > domain 0: span 1-2 level MC > groups: 1 2 > domain 1: span 0-3 level CPU > groups: 1-2 0,3 > domain 2: span 0-3 level NODE > groups: 0-3 > CPU2 attaching sched-domain: > domain 0: span 1-2 level MC > groups: 2 1 > domain 1: span 0-3 level CPU > groups: 1-2 0,3 > domain 2: span 0-3 level NODE > groups: 0-3 > CPU3 attaching sched-domain: > domain 0: span 0,3 level MC > groups: 3 0 > domain 1: span 0-3 level CPU > groups: 0,3 1-2 > domain 2: span 0-3 level NODE > groups: 0-3 > net_namespace: 1552 bytes > Booting paravirtualized kernel on bare hardware > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63 > PCI: MCFG area at e0000000 reserved in E820 > PCI: Using MMCONFIG at e0000000 - e3ffffff > PCI: Using configuration type 1 for base access > ACPI: EC: Look up EC in DSDT > ACPI: Interpreter enabled > ACPI: (supports S0 S3 S4 S5) > ACPI: Using IOAPIC for interrupt routing > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: 0000:00:1a.0 reg 20 io port: [e100, e11f] > PCI: 0000:00:1a.1 reg 20 io port: [e200, e21f] > PCI: 0000:00:1a.2 reg 20 io port: [e000, e01f] > PCI: 0000:00:1a.7 reg 10 32bit mmio: [e8104000, e81043ff] > PCI: 0000:00:1b.0 reg 10 64bit mmio: [e8100000, e8103fff] > pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1b.0: PME# disabled > pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.0: PME# disabled > pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.4: PME# disabled > pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold > pci 0000:00:1c.5: PME# disabled > PCI: 0000:00:1d.0 reg 20 io port: [e300, e31f] > PCI: 0000:00:1d.1 reg 20 io port: [e400, e41f] > PCI: 0000:00:1d.2 reg 20 io port: [e500, e51f] > PCI: 0000:00:1d.7 reg 10 32bit mmio: [e8105000, e81053ff] > PCI: 0000:00:1f.2 reg 10 io port: [0, 7] > PCI: 0000:00:1f.2 reg 14 io port: [0, 3] > PCI: 0000:00:1f.2 reg 18 io port: [0, 7] > PCI: 0000:00:1f.2 reg 1c io port: [0, 3] > PCI: 0000:00:1f.2 reg 20 io port: [f000, f00f] > PCI: 0000:00:1f.2 reg 24 io port: [f100, f10f] > PCI: 0000:00:1f.3 reg 10 64bit mmio: [e8106000, e81060ff] > PCI: 0000:00:1f.3 reg 20 io port: [500, 51f] > PCI: 0000:00:1f.5 reg 10 io port: [e700, e707] > PCI: 0000:00:1f.5 reg 14 io port: [e800, e803] > PCI: 0000:00:1f.5 reg 18 io port: [e900, e907] > PCI: 0000:00:1f.5 reg 1c io port: [ea00, ea03] > PCI: 0000:00:1f.5 reg 20 io port: [eb00, eb0f] > PCI: 0000:00:1f.5 reg 24 io port: [ec00, ec0f] > PCI: 0000:02:00.0 reg 10 io port: [c000, c007] > PCI: 0000:02:00.0 reg 14 io port: [c100, c103] > PCI: 0000:02:00.0 reg 18 io port: [c200, c207] > PCI: 0000:02:00.0 reg 1c io port: [c300, c303] > PCI: 0000:02:00.0 reg 20 io port: [c400, c40f] > Pre-1.1 PCIe device detected, disable ASPM for 0000:00:1c.4. It can be > enabled forcedly with 'pcie_aspm=force' > PCI: bridge 0000:00:1c.4 io port: [c000, cfff] > PCI: bridge 0000:00:1c.4 32bit mmio: [e7000000, e7ffffff] > PCI: 0000:03:00.0 reg 10 io port: [d000, d0ff] > PCI: 0000:03:00.0 reg 18 64bit mmio: [e8010000, e8010fff] > PCI: 0000:03:00.0 reg 20 64bit mmio: [e8000000, e800ffff] > PCI: 0000:03:00.0 reg 30 32bit mmio: [0, ffff] > pci 0000:03:00.0: supports D1 > pci 0000:03:00.0: supports D2 > pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold > pci 0000:03:00.0: PME# disabled > PCI: bridge 0000:00:1c.5 io port: [d000, dfff] > PCI: bridge 0000:00:1c.5 32bit mmio: [e4000000, e4ffffff] > PCI: bridge 0000:00:1c.5 64bit mmio pref: [e8000000, e80fffff] > PCI: 0000:04:00.0 reg 10 32bit mmio: [e5000000, e5ffffff] > PCI: 0000:04:00.0 reg 14 32bit mmio: [d0000000, dfffffff] > PCI: 0000:04:00.0 reg 30 32bit mmio: [0, 1ffff] > pci 0000:00:1e.0: transparent bridge > PCI: bridge 0000:00:1e.0 32bit mmio: [e5000000, e6ffffff] > PCI: bridge 0000:00:1e.0 64bit mmio pref: [d0000000, dfffffff] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) > ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 *6 7 9 10 11 12 14 15) > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > ACPI: bus type pnp registered > pnp: PnP ACPI: found 15 devices > ACPI: ACPI bus type pnp unregistered > PCI: Using ACPI for IRQ routing > NetLabel: Initializing > NetLabel: domain hash size = 128 > NetLabel: protocols = UNLABELED CIPSOv4 > NetLabel: unlabeled traffic allowed by default > DMAR:parse DMAR table failure. > PCI-GART: No AMD northbridge found. > hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 > hpet0: 4 64-bit timers, 14318180 Hz > ACPI: RTC can wake from S4 > system 00:01: ioport range 0x4d0-0x4d1 has been reserved > system 00:01: ioport range 0x290-0x29f has been reserved > system 00:01: ioport range 0x800-0x87f has been reserved > system 00:01: ioport range 0x290-0x294 has been reserved > system 00:01: ioport range 0x880-0x88f has been reserved > system 00:01: ioport range 0x4c0-0x4ff could not be reserved > system 00:0b: ioport range 0x400-0x4bf has been reserved > system 00:0c: iomem range 0xe0000000-0xe3ffffff could not be reserved > system 00:0d: iomem range 0xcf800-0xcffff has been reserved > system 00:0d: iomem range 0xf0000-0xf7fff could not be reserved > system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved > system 00:0d: iomem range 0xfc000-0xfffff could not be reserved > system 00:0d: iomem range 0x7fee0000-0x7fefffff could not be reserved > system 00:0d: iomem range 0x0-0x9ffff could not be reserved > system 00:0d: iomem range 0x100000-0x7fedffff could not be reserved > system 00:0d: iomem range 0xfec00000-0xfec00fff could not be reserved > system 00:0d: iomem range 0xfed10000-0xfed1dfff could not be reserved > system 00:0d: iomem range 0xfed20000-0xfed8ffff could not be reserved > system 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved > system 00:0d: iomem range 0xffb00000-0xffb7ffff could not be reserved > system 00:0d: iomem range 0xfff00000-0xffffffff could not be reserved > system 00:0d: iomem range 0xe0000-0xeffff has been reserved > pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 > pci 0000:00:1c.0: IO window: disabled > pci 0000:00:1c.0: MEM window: disabled > pci 0000:00:1c.0: PREFETCH window: disabled > pci 0000:00:1c.4: PCI bridge, secondary bus 0000:02 > pci 0000:00:1c.4: IO window: 0xc000-0xcfff > pci 0000:00:1c.4: MEM window: 0xe7000000-0xe7ffffff > pci 0000:00:1c.4: PREFETCH window: disabled > pci 0000:00:1c.5: PCI bridge, secondary bus 0000:03 > pci 0000:00:1c.5: IO window: 0xd000-0xdfff > pci 0000:00:1c.5: MEM window: 0xe4000000-0xe4ffffff > pci 0000:00:1c.5: PREFETCH window: 0x000000e8000000-0x000000e80fffff > pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04 > pci 0000:00:1e.0: IO window: disabled > pci 0000:00:1e.0: MEM window: 0xe5000000-0xe6ffffff > pci 0000:00:1e.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff > pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > pci 0000:00:1c.0: setting latency timer to 64 > pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > pci 0000:00:1c.4: setting latency timer to 64 > pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 > pci 0000:00:1c.5: setting latency timer to 64 > pci 0000:00:1e.0: setting latency timer to 64 > bus: 00 index 0 io port: [0, ffff] > bus: 00 index 1 mmio: [0, ffffffffffffffff] > bus: 01 index 0 mmio: [0, 0] > bus: 01 index 1 mmio: [0, 0] > bus: 01 index 2 mmio: [0, 0] > bus: 01 index 3 mmio: [0, 0] > bus: 02 index 0 io port: [c000, cfff] > bus: 02 index 1 mmio: [e7000000, e7ffffff] > bus: 02 index 2 mmio: [0, 0] > bus: 02 index 3 mmio: [0, 0] > bus: 03 index 0 io port: [d000, dfff] > bus: 03 index 1 mmio: [e4000000, e4ffffff] > bus: 03 index 2 mmio: [e8000000, e80fffff] > bus: 03 index 3 mmio: [0, 0] > bus: 04 index 0 mmio: [0, 0] > bus: 04 index 1 mmio: [e5000000, e6ffffff] > bus: 04 index 2 mmio: [d0000000, dfffffff] > bus: 04 index 3 io port: [0, ffff] > bus: 04 index 4 mmio: [0, ffffffffffffffff] > NET: Registered protocol family 2 > IP route cache hash table entries: 65536 (order: 7, 524288 bytes) > TCP established hash table entries: 262144 (order: 10, 4194304 bytes) > TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > TCP: Hash tables configured (established 262144 bind 65536) > TCP reno registered > NET: Registered protocol family 1 > checking if image is initramfs... it is > Switched to high resolution mode on CPU 2 > Switched to high resolution mode on CPU 3 > Switched to high resolution mode on CPU 0 > Switched to high resolution mode on CPU 1 > Freeing initrd memory: 3911k freed > audit: initializing netlink socket (disabled) > type=2000 audit(1228006010.551:1): initialized > HugeTLB registered 2 MB page size, pre-allocated 0 pages > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > msgmni has been set to 4024 > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > pci 0000:04:00.0: Boot video device > pcieport-driver 0000:00:1c.0: setting latency timer to 64 > pcieport-driver 0000:00:1c.0: found MSI capability > pci_express 0000:00:1c.0:pcie00: allocate port service > pci_express 0000:00:1c.0:pcie02: allocate port service > pci_express 0000:00:1c.0:pcie03: allocate port service > pcieport-driver 0000:00:1c.4: setting latency timer to 64 > pcieport-driver 0000:00:1c.4: found MSI capability > pci_express 0000:00:1c.4:pcie00: allocate port service > pci_express 0000:00:1c.4:pcie02: allocate port service > pci_express 0000:00:1c.4:pcie03: allocate port service > pcieport-driver 0000:00:1c.5: setting latency timer to 64 > pcieport-driver 0000:00:1c.5: found MSI capability > pci_express 0000:00:1c.5:pcie00: allocate port service > pci_express 0000:00:1c.5:pcie02: allocate port service > pci_express 0000:00:1c.5:pcie03: allocate port service > hpet_resources: 0xfed00000 is busy > Linux agpgart interface v0.103 > Serial: 8250/16550 driver4 ports, IRQ sharing enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > brd: module loaded > input: Macintosh mouse button emulation as /class/input/input0 > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > serio: i8042 AUX port at 0x60,0x64 irq 12 > mice: PS/2 mouse device common for all mice > input: AT Translated Set 2 keyboard as /class/input/input1 > cpuidle: using governor ladder > cpuidle: using governor menu > TCP cubic registered > registered taskstats version 1 > BIOS EDD facility v0.16 2004-Jun-25, 6 devices found > Freeing unused kernel memory: 532k freed > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > ehci_hcd 0000:00:1a.7: setting latency timer to 64 > ehci_hcd 0000:00:1a.7: EHCI Host Controller > ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 > ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported > ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe8104000 > ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 6 ports detected > input: PS2++ Logitech MX Mouse as /class/input/input2 > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: EHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.27.7 ehci_hcd > usb usb1: SerialNumber: 0000:00:1a.7 > ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 > ehci_hcd 0000:00:1d.7: setting latency timer to 64 > ehci_hcd 0000:00:1d.7: EHCI Host Controller > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 > ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported > ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe8105000 > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 6 ports detected > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: EHCI Host Controller > usb usb2: Manufacturer: Linux 2.6.27.7 ehci_hcd > usb usb2: SerialNumber: 0000:00:1d.7 > ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver > USB Universal Host Controller Interface driver v3.0 > uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > uhci_hcd 0000:00:1a.0: setting latency timer to 64 > uhci_hcd 0000:00:1a.0: UHCI Host Controller > uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 > uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e100 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb3: Product: UHCI Host Controller > usb usb3: Manufacturer: Linux 2.6.27.7 uhci_hcd > usb usb3: SerialNumber: 0000:00:1a.0 > uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 > uhci_hcd 0000:00:1a.1: setting latency timer to 64 > uhci_hcd 0000:00:1a.1: UHCI Host Controller > uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 > uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e200 > usb usb4: configuration #1 chosen from 1 choice > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb4: Product: UHCI Host Controller > usb usb4: Manufacturer: Linux 2.6.27.7 uhci_hcd > usb usb4: SerialNumber: 0000:00:1a.1 > uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > uhci_hcd 0000:00:1a.2: setting latency timer to 64 > uhci_hcd 0000:00:1a.2: UHCI Host Controller > uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 > uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000e000 > usb usb5: configuration #1 chosen from 1 choice > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 2 ports detected > usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb5: Product: UHCI Host Controller > usb usb5: Manufacturer: Linux 2.6.27.7 uhci_hcd > usb usb5: SerialNumber: 0000:00:1a.2 > uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 > uhci_hcd 0000:00:1d.0: setting latency timer to 64 > uhci_hcd 0000:00:1d.0: UHCI Host Controller > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 > uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e300 > usb usb6: configuration #1 chosen from 1 choice > hub 6-0:1.0: USB hub found > hub 6-0:1.0: 2 ports detected > usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb6: Product: UHCI Host Controller > usb usb6: Manufacturer: Linux 2.6.27.7 uhci_hcd > usb usb6: SerialNumber: 0000:00:1d.0 > uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > uhci_hcd 0000:00:1d.1: setting latency timer to 64 > uhci_hcd 0000:00:1d.1: UHCI Host Controller > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 > uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400 > usb usb7: configuration #1 chosen from 1 choice > hub 7-0:1.0: USB hub found > hub 7-0:1.0: 2 ports detected > usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb7: Product: UHCI Host Controller > usb usb7: Manufacturer: Linux 2.6.27.7 uhci_hcd > usb usb7: SerialNumber: 0000:00:1d.1 > uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > uhci_hcd 0000:00:1d.2: setting latency timer to 64 > uhci_hcd 0000:00:1d.2: UHCI Host Controller > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 > uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e500 > usb usb8: configuration #1 chosen from 1 choice > hub 8-0:1.0: USB hub found > hub 8-0:1.0: 2 ports detected > usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 > usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb8: Product: UHCI Host Controller > usb usb8: Manufacturer: Linux 2.6.27.7 uhci_hcd > usb usb8: SerialNumber: 0000:00:1d.2 > SCSI subsystem initialized > Driver 'sd' needs updating - please use bus_type methods > No dock devices found. > libata version 3.00 loaded. > ata_piix 0000:00:1f.2: version 2.12 > ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] > ata_piix 0000:00:1f.2: setting latency timer to 64 > scsi0 : ata_piix > scsi1 : ata_piix > ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 > ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 > ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata1.00: HPA detected: current 625140335, native 625142448 > ata1.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 > ata1.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata1.01: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 > ata1.01: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata1.00: configured for UDMA/133 > ata1.01: configured for UDMA/133 > ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata2.00: HPA detected: current 625140335, native 625142448 > ata2.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 > ata2.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata2.01: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 > ata2.01: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata2.00: configured for UDMA/133 > ata2.01: configured for UDMA/133 > isa bounce pool size: 16 pages > scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 > ANSI: 5 > sd 0:0:0:0: [sda] 625140335 512-byte hardware sectors (320072 MB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 0:0:0:0: [sda] 625140335 512-byte hardware sectors (320072 MB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sda: sda1 sda2 sda3 < sda5 > > sd 0:0:0:0: [sda] Attached SCSI disk > scsi 0:0:1:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 > ANSI: 5 > sd 0:0:1:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) > sd 0:0:1:0: [sdb] Write Protect is off > sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 0:0:1:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) > sd 0:0:1:0: [sdb] Write Protect is off > sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sdb: sdb1 sdb2 sdb3 < sdb5 > > sd 0:0:1:0: [sdb] Attached SCSI disk > scsi 1:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 > ANSI: 5 > sd 1:0:0:0: [sdc] 625140335 512-byte hardware sectors (320072 MB) > sd 1:0:0:0: [sdc] Write Protect is off > sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00 > sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 1:0:0:0: [sdc] 625140335 512-byte hardware sectors (320072 MB) > sd 1:0:0:0: [sdc] Write Protect is off > sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00 > sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sdc: sdc1 sdc2 sdc3 < sdc5 > > sd 1:0:0:0: [sdc] Attached SCSI disk > scsi 1:0:1:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 > ANSI: 5 > sd 1:0:1:0: [sdd] 625142448 512-byte hardware sectors (320073 MB) > sd 1:0:1:0: [sdd] Write Protect is off > sd 1:0:1:0: [sdd] Mode Sense: 00 3a 00 00 > sd 1:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 1:0:1:0: [sdd] 625142448 512-byte hardware sectors (320073 MB) > sd 1:0:1:0: [sdd] Write Protect is off > sd 1:0:1:0: [sdd] Mode Sense: 00 3a 00 00 > sd 1:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sdd: sdd1 sdd2 sdd3 < sdd5 > > sd 1:0:1:0: [sdd] Attached SCSI disk > ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] > ata_piix 0000:00:1f.5: setting latency timer to 64 > scsi2 : ata_piix > scsi3 : ata_piix > ata3: SATA max UDMA/133 cmd 0xe700 ctl 0xe800 bmdma 0xeb00 irq 19 > ata4: SATA max UDMA/133 cmd 0xe900 ctl 0xea00 bmdma 0xeb08 irq 19 > ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata3.00: HPA detected: current 625140335, native 625142448 > ata3.00: ATA-8: WDC WD3200AAKS-00VYA0, 12.01B02, max UDMA/133 > ata3.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata3.00: configured for UDMA/133 > ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > ata4.00: ATA-8: WDC WD3200AAKS-00VYA0, 12.01B02, max UDMA/133 > ata4.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata4.00: configured for UDMA/133 > scsi 2:0:0:0: Direct-Access ATA WDC WD3200AAKS-0 12.0 PQ: 0 > ANSI: 5 > sd 2:0:0:0: [sde] 625140335 512-byte hardware sectors (320072 MB) > sd 2:0:0:0: [sde] Write Protect is off > sd 2:0:0:0: [sde] Mode Sense: 00 3a 00 00 > sd 2:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 2:0:0:0: [sde] 625140335 512-byte hardware sectors (320072 MB) > sd 2:0:0:0: [sde] Write Protect is off > sd 2:0:0:0: [sde] Mode Sense: 00 3a 00 00 > sd 2:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sde: sde1 sde2 sde3 < sde5 > > sd 2:0:0:0: [sde] Attached SCSI disk > scsi 3:0:0:0: Direct-Access ATA WDC WD3200AAKS-0 12.0 PQ: 0 > ANSI: 5 > sd 3:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB) > sd 3:0:0:0: [sdf] Write Protect is off > sd 3:0:0:0: [sdf] Mode Sense: 00 3a 00 00 > sd 3:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sd 3:0:0:0: [sdf] 625142448 512-byte hardware sectors (320073 MB) > sd 3:0:0:0: [sdf] Write Protect is off > sd 3:0:0:0: [sdf] Mode Sense: 00 3a 00 00 > sd 3:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sdf: sdf1 sdf2 sdf3 < sdf5 > > sd 3:0:0:0: [sdf] Attached SCSI disk > pata_jmicron 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > pata_jmicron 0000:02:00.0: setting latency timer to 64 > scsi4 : pata_jmicron > scsi5 : pata_jmicron > ata5: PATA max UDMA/100 cmd 0xc000 ctl 0xc100 bmdma 0xc400 irq 16 > ata6: PATA max UDMA/100 cmd 0xc200 ctl 0xc300 bmdma 0xc408 irq 16 > ata5.00: ATAPI: Memorex 16X-DDL-IN, 1.A3, max UDMA/33 > ata5.00: configured for UDMA/33 > scsi 4:0:0:0: CD-ROM Memorex 16X-DDL-IN 1.A3 PQ: 0 > ANSI: 5 > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > sd 0:0:0:0: Attached scsi generic sg0 type 0 > sd 0:0:1:0: Attached scsi generic sg1 type 0 > sd 1:0:0:0: Attached scsi generic sg2 type 0 > sd 1:0:1:0: Attached scsi generic sg3 type 0 > sd 2:0:0:0: Attached scsi generic sg4 type 0 > sd 3:0:0:0: Attached scsi generic sg5 type 0 > scsi 4:0:0:0: Attached scsi generic sg6 type 5 > Driver 'sr' needs updating - please use bus_type methods > sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray > Uniform CD-ROM driver Revision: 3.20 > sr 4:0:0:0: Attached scsi CD-ROM sr0 > parport_pc 00:08: reported by Plug and Play ACPI > parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] > input: PC Speaker as /class/input/input3 > ppdev: user-space parallel port driver > r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded > r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > r8169 0000:03:00.0: setting latency timer to 64 > eth0: RTL8168c/8111c at 0xffffc2000032e000, 00:1f:d0:83:97:d1, XID > 3c4000c0 IRQ 1276 > rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 > rtc0: alarms up to one month, hpet irqs > input: Power Button (FF) as /class/input/input4 > ACPI: Power Button (FF) [PWRF] > input: Power Button (CM) as /class/input/input5 > ACPI: Power Button (CM) [PWRB] > i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > ACPI: SSDT 7FEE7F80, 022A (r1 PmRef Cpu0Ist 3000 INTL 20040311) > ACPI: CPU0 (power states: C1[C1] C2[C2]) > processor ACPI0007:00: registered as cooling_device0 > ACPI: Processor [CPU0] (supports 8 throttling states) > ACPI: SSDT 7FEE8440, 0152 (r1 PmRef Cpu1Ist 3000 INTL 20040311) > ACPI: CPU1 (power states: C1[C1] C2[C2]) > processor ACPI0007:01: registered as cooling_device1 > ACPI: Processor [CPU1] (supports 8 throttling states) > ACPI: SSDT 7FEE85A0, 0152 (r1 PmRef Cpu2Ist 3000 INTL 20040311) > ACPI: CPU2 (power states: C1[C1] C2[C2]) > processor ACPI0007:02: registered as cooling_device2 > ACPI: Processor [CPU2] (supports 8 throttling states) > ACPI: SSDT 7FEE8700, 0152 (r1 PmRef Cpu3Ist 3000 INTL 20040311) > ACPI: CPU3 (power states: C1[C1] C2[C2]) > processor ACPI0007:03: registered as cooling_device3 > ACPI: Processor [CPU3] (supports 8 throttling states) > md: bind > md: bind > md: bind > HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 > HDA Intel 0000:00:1b.0: setting latency timer to 64 > md: bind > md: bind > md: raid10 personality registered for level 10 > raid10: raid set md0 active with 5 out of 6 devices > md: bind > RAID10 conf printout: > --- wd:5 rd:6 > disk 0, wo:0, o:1, dev:sda5 > disk 1, wo:0, o:1, dev:sdb5 > disk 2, wo:0, o:1, dev:sdc5 > disk 3, wo:1, o:1, dev:sdd5 > disk 4, wo:0, o:1, dev:sde5 > disk 5, wo:0, o:1, dev:sdf5 > md: recovery of RAID array md0 > md: minimum _guaranteed_ speed: 1000 KB/sec/disk. > md: using maximum available idle IO bandwidth (but not more than > 200000 KB/sec) for recovery. > md: using 128k window, over a total of 20980736 blocks. > device-mapper: uevent: version 1.0.3 > device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: > dm-devel@redhat.com > EXT3 FS on sda1, internal journal > loop: module loaded > Adding 1959920k swap on /dev/sda2. Priority:-1 extents:1 across:1959920k > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > r8169: eth0: link up > r8169: eth0: link up > NET: Registered protocol family 17 > eth0: no IPv6 routers present > md: md0: recovery done. > RAID10 conf printout: > --- wd:6 rd:6 > disk 0, wo:0, o:1, dev:sda5 > disk 1, wo:0, o:1, dev:sdb5 > disk 2, wo:0, o:1, dev:sdc5 > disk 3, wo:0, o:1, dev:sdd5 > disk 4, wo:0, o:1, dev:sde5 > disk 5, wo:0, o:1, dev:sdf5 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-raid" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- Bill Davidsen "Woe unto the statesman who makes war without a reason that will still be valid when the war is over..." Otto von Bismark