From: "Guy Watkins" <guy@watkins-home.com>
To: "'Majed B.'" <majedb@gmail.com>
Cc: 'LinuxRaid' <linux-raid@vger.kernel.org>
Subject: RE: RAID6 array lost a disk, can someone decode the error?
Date: Wed, 11 Nov 2009 02:01:43 -0500 [thread overview]
Message-ID: <CA641DF8B4814BD390BF8BC522B55AB4@m5> (raw)
In-Reply-To: <70ed7c3e0911102152j23404aadgff519e4344dd7d1@mail.gmail.com>
} -----Original Message-----
} From: Majed B. [mailto:majedb@gmail.com]
} Sent: Wednesday, November 11, 2009 12:52 AM
} To: Guy Watkins
} Cc: LinuxRaid
} Subject: Re: RAID6 array lost a disk, can someone decode the error?
}
} You seem to have very high numbers in Hardware_ECC_Recovered and
} Raw_Read_Error_Rate. I suggest you replace your cables.
I thought I just did not understand those fields. They seemed high/bad to
me too, but I do not have any other disks to compare to. You think all 4
cables could be bad? They are the same, but no idea what brand.
ok, any recommended vendor for new cables?
} You don't have bad sectors, which is good.
}
} Are you using the controller for RAD or just as a way to connect your
} disks?
JBOD. I did not know that controller had RAID. :)
} I've had similar link-reset problems, but not written related. Turns
} out one of the disks had a bad PCB.
}
} On Wed, Nov 11, 2009 at 8:37 AM, Guy Watkins <guy@watkins-home.com> wrote:
} > I have 2 4-disk RAID6 arrays that loose a disk sometimes. Maybe once
} every
} > month or 3. As far as I can tell I don't have disks that have un-
} readable
} > blocks. The RAID1 arrays also loose disks sometimes. I have the 4
} disks on
} > 1 controller, from lspci:
} > 00:0e.0 Mass storage controller: Promise Technology, Inc. PDC20318
} (SATA150
} > TX4) (rev 02)
} >
} > I thought the RAID6 logic corrected single block errors? Maybe not on a
} > write? And I think this is a write because of "super_written"?
} >
} > The array is a RAID6 but the errors say RAID5?
} >
} > When I remove and add the disks back in they rebuild just fine.
} >
} > Anyway, does anyone understand what this error really is? Is it bad
} disks?
} > Bad cable? Bad controller? Bad sunspots? :)
} >
} > I did see that a smart test had failed at about the same time. I also
} read
} > that some disks or controllers can't handle smart tests. Could that be
} it?
} > I don't run smart tests vary often, so I know the other failures from
} the
} > past were not caused by a smart test. Maybe I am doing the tests wrong?
} I
} > used this command: "smartctl --test=long /dev/sda"
} >
} > All info I think might be needed:
} >
} > The disks are all Seagate ST3320620AS (320 GB disks).
} >
} > # uname -a
} > Linux linux.watkins-home.com 2.6.27.35-170.2.94.fc10.i686 #1 SMP Thu Oct
} 1
} > 14:58:51 EDT 2009 i686 i686 i386 GNU/Linux
} >
} > # rpm -qa mdadm
} > mdadm-2.6.9-1.fc10.i386
} >
} > From /var/log/messages-20091108
} > Nov 1 21:48:29 linux kernel: ata4.00: exception Emask 0x10 SAct 0x0
} SErr
} > 0x180203 action 0x6 frozen
} > Nov 1 21:48:29 linux kernel: ata4: SError: { RecovData RecovComm
} Persist
} > 10B8B Dispar }
} > Nov 1 21:48:29 linux kernel: ata4.00: cmd
} > ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
} > Nov 1 21:48:29 linux kernel: res 40/00:01:00:4f:c2/00:00:00:00:00/00
} Emask
} > 0x14 (ATA bus error)
} > Nov 1 21:48:29 linux kernel: ata4.00: status: { DRDY }
} > Nov 1 21:48:29 linux kernel: ata4: hard resetting link
} > Nov 1 21:48:31 linux kernel: ata4: SATA link up 1.5 Gbps (SStatus 113
} > SControl 300)
} > Nov 1 21:48:31 linux kernel: ata4.00: configured for UDMA/133
} > Nov 1 21:48:31 linux kernel: ata4.00: device reported invalid CHS
} sector 0
} > Nov 1 21:48:31 linux kernel: ata4: EH complete
} > Nov 1 21:48:31 linux kernel: sd 3:0:0:0: [sdb] 625142448 512-byte
} hardware
} > sectors (320073 MB)
} > Nov 1 21:48:31 linux kernel: end_request: I/O error, dev sdb, sector
} > 34089705
} > Nov 1 21:48:31 linux kernel: md: super_written gets error=-5,
} uptodate=0
} > Nov 1 21:48:31 linux kernel: raid5: Disk failure on sdb2, disabling
} device.
} > Nov 1 21:48:31 linux kernel: raid5: Operation continuing on 3 devices.
} > Nov 1 21:48:31 linux kernel: sd 3:0:0:0: [sdb] Write Protect is off
} > Nov 1 21:48:31 linux kernel: sd 3:0:0:0: [sdb] Write cache: enabled,
} read
} > cache: enabled, doesn't support DPO or FUA
} > Nov 1 21:48:31 linux kernel: RAID5 conf printout:
} > Nov 1 21:48:31 linux kernel: --- rd:4 wd:3
} > Nov 1 21:48:31 linux kernel: disk 0, o:0, dev:sdb2
} > Nov 1 21:48:31 linux kernel: disk 1, o:1, dev:sdd2
} > Nov 1 21:48:31 linux kernel: disk 2, o:1, dev:sdc2
} > Nov 1 21:48:31 linux kernel: disk 3, o:1, dev:sda2
} > Nov 1 21:48:31 linux kernel: RAID5 conf printout:
} > Nov 1 21:48:31 linux kernel: --- rd:4 wd:3
} > Nov 1 21:48:31 linux kernel: disk 1, o:1, dev:sdd2
} > Nov 1 21:48:31 linux kernel: disk 2, o:1, dev:sdc2
} > Nov 1 21:48:31 linux kernel: disk 3, o:1, dev:sda2
} >
} > # cat /proc/mdstat
} > Personalities : [raid6] [raid5] [raid4] [raid1]
} > md0 : active raid1 sdd1[0] sda1[3] sdc1[2] sdb1[1]
} > 264960 blocks [4/4] [UUUU]
} > bitmap: 0/33 pages [0KB], 4KB chunk
} >
} > md4 : active raid6 sdd4[0] sda4[3] sdc4[2] sdb4[4](F)
} > 586853888 blocks level 6, 256k chunk, algorithm 2 [4/3] [U_UU]
} > bitmap: 70/140 pages [280KB], 1024KB chunk
} >
} > md2 : active raid1 sdb3[0] sda3[1]
} > 2096384 blocks [2/2] [UU]
} > bitmap: 0/128 pages [0KB], 8KB chunk
} >
} > md1 : active raid1 sdd3[0] sdc3[1]
} > 2096384 blocks [2/2] [UU]
} > bitmap: 0/128 pages [0KB], 8KB chunk
} >
} > md3 : active raid6 sdb2[4](F) sdd2[1] sda2[3] sdc2[2]
} > 33559552 blocks level 6, 256k chunk, algorithm 2 [4/3] [_UUU]
} > bitmap: 119/129 pages [476KB], 64KB chunk
} >
} > unused devices: <none>
} >
} > # smartctl -a /dev/sda
} > smartctl version 5.38 [i386-redhat-linux-gnu] Copyright (C) 2002-8 Bruce
} > Allen
} > Home page is http://smartmontools.sourceforge.net/
} >
} > === START OF INFORMATION SECTION ===
} > Model Family: Seagate Barracuda 7200.10 family
} > Device Model: ST3320620AS
} > Serial Number: 3QF08NDL
} > Firmware Version: 3.AAD
} > User Capacity: 320,072,933,376 bytes
} > Device is: In smartctl database [for details use: -P show]
} > ATA Version is: 7
} > ATA Standard is: Exact ATA specification draft version not indicated
} > Local Time is: Tue Nov 10 23:57:28 2009 EST
} > SMART support is: Available - device has SMART capability.
} > SMART support is: Enabled
} >
} > === START OF READ SMART DATA SECTION ===
} > SMART overall-health self-assessment test result: PASSED
} >
} > General SMART Values:
} > Offline data collection status: (0x82) Offline data collection activity
} > was completed without error.
} > Auto Offline Data Collection:
} > Enabled.
} > Self-test execution status: ( 0) The previous self-test routine
} > completed
} > without error or no self-test has
} > ever
} > been run.
} > Total time to complete Offline
} > data collection: ( 430) seconds.
} > Offline data collection
} > capabilities: (0x5b) SMART execute Offline immediate.
} > Auto Offline data collection
} on/off
} > support.
} > Suspend Offline collection upon
} new
} > command.
} > Offline surface scan supported.
} > Self-test supported.
} > No Conveyance Self-test
} supported.
} > Selective Self-test supported.
} > SMART capabilities: (0x0003) Saves SMART data before entering
} > power-saving mode.
} > Supports SMART auto save timer.
} > Error logging capability: (0x01) Error logging supported.
} > General Purpose Logging
} supported.
} > Short self-test routine
} > recommended polling time: ( 1) minutes.
} > Extended self-test routine
} > recommended polling time: ( 115) minutes.
} >
} > SMART Attributes Data Structure revision number: 10
} > Vendor Specific SMART Attributes with Thresholds:
} > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
} UPDATED
} > WHEN_FAILED RAW_VALUE
} > 1 Raw_Read_Error_Rate 0x000f 114 097 006 Pre-fail Always
} > - 77830969
} > 3 Spin_Up_Time 0x0003 094 090 000 Pre-fail Always
} > - 0
} > 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
} > - 83
} > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
} > - 0
} > 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always
} > - 150227385
} > 9 Power_On_Hours 0x0032 073 073 000 Old_age Always
} > - 23919
} > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
} > - 0
} > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
} > - 116
} > 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
} > - 0
} > 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
} > - 0
} > 190 Airflow_Temperature_Cel 0x0022 061 046 045 Old_age Always
} > - 39 (Lifetime Min/Max 37/43)
} > 194 Temperature_Celsius 0x0022 039 054 000 Old_age Always
} > - 39 (0 21 0 0)
} > 195 Hardware_ECC_Recovered 0x001a 065 054 000 Old_age Always
} > - 102168431
} > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
} > - 0
} > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
} Offline
} > - 0
} > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
} > - 0
} > 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
} Offline
} > - 0
} > 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
} > - 0
} >
} > SMART Error Log Version: 1
} > No Errors Logged
} >
} > SMART Self-test log structure revision number 1
} > Num Test_Description Status Remaining
} LifeTime(hours)
} > LBA_of_first_error
} > # 1 Extended offline Completed without error 00% 23730
} > -
} > # 2 Extended offline Completed without error 00% 22581
} > -
} > # 3 Short offline Completed without error 00% 22577
} > -
} > # 4 Extended offline Completed without error 00% 17267
} > -
} > # 5 Short offline Completed without error 00% 17259
} > -
} > # 6 Extended offline Completed without error 00% 384
} > -
} >
} > SMART Selective self-test log data structure revision number 1
} > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
} > 1 0 0 Not_testing
} > 2 0 0 Not_testing
} > 3 0 0 Not_testing
} > 4 0 0 Not_testing
} > 5 0 0 Not_testing
} > Selective self-test flags (0x0):
} > After scanning selected spans, do NOT read-scan remainder of disk.
} > If Selective self-test is pending on power-up, resume after 0 minute
} delay.
} >
} > # smartctl -a /dev/sdb
} > smartctl version 5.38 [i386-redhat-linux-gnu] Copyright (C) 2002-8 Bruce
} > Allen
} > Home page is http://smartmontools.sourceforge.net/
} >
} > === START OF INFORMATION SECTION ===
} > Model Family: Seagate Barracuda 7200.10 family
} > Device Model: ST3320620AS
} > Serial Number: 3QF08SKR
} > Firmware Version: 3.AAD
} > User Capacity: 320,072,933,376 bytes
} > Device is: In smartctl database [for details use: -P show]
} > ATA Version is: 7
} > ATA Standard is: Exact ATA specification draft version not indicated
} > Local Time is: Wed Nov 11 00:03:14 2009 EST
} > SMART support is: Available - device has SMART capability.
} > SMART support is: Enabled
} >
} > === START OF READ SMART DATA SECTION ===
} > SMART overall-health self-assessment test result: PASSED
} >
} > General SMART Values:
} > Offline data collection status: (0x82) Offline data collection activity
} > was completed without error.
} > Auto Offline Data Collection:
} > Enabled.
} > Self-test execution status: ( 37) The self-test routine was
} > interrupted
} > by the host with a hard or soft
} > reset.
} > Total time to complete Offline
} > data collection: ( 430) seconds.
} > Offline data collection
} > capabilities: (0x5b) SMART execute Offline immediate.
} > Auto Offline data collection
} on/off
} > support.
} > Suspend Offline collection upon
} new
} > command.
} > Offline surface scan supported.
} > Self-test supported.
} > No Conveyance Self-test
} supported.
} > Selective Self-test supported.
} > SMART capabilities: (0x0003) Saves SMART data before entering
} > power-saving mode.
} > Supports SMART auto save timer.
} > Error logging capability: (0x01) Error logging supported.
} > General Purpose Logging
} supported.
} > Short self-test routine
} > recommended polling time: ( 1) minutes.
} > Extended self-test routine
} > recommended polling time: ( 115) minutes.
} >
} > SMART Attributes Data Structure revision number: 10
} > Vendor Specific SMART Attributes with Thresholds:
} > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
} UPDATED
} > WHEN_FAILED RAW_VALUE
} > 1 Raw_Read_Error_Rate 0x000f 111 091 006 Pre-fail Always
} > - 136981744
} > 3 Spin_Up_Time 0x0003 099 090 000 Pre-fail Always
} > - 0
} > 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
} > - 104
} > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
} > - 1
} > 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always
} > - 257877357
} > 9 Power_On_Hours 0x0032 073 073 000 Old_age Always
} > - 23916
} > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
} > - 0
} > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
} > - 157
} > 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
} > - 0
} > 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
} > - 0
} > 190 Airflow_Temperature_Cel 0x0022 059 049 045 Old_age Always
} > - 41 (Lifetime Min/Max 38/43)
} > 194 Temperature_Celsius 0x0022 041 051 000 Old_age Always
} > - 41 (0 21 0 0)
} > 195 Hardware_ECC_Recovered 0x001a 063 054 000 Old_age Always
} > - 160751697
} > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
} > - 0
} > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
} Offline
} > - 0
} > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
} > - 0
} > 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
} Offline
} > - 0
} > 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
} > - 0
} >
} > SMART Error Log Version: 1
} > No Errors Logged
} >
} > SMART Self-test log structure revision number 1
} > Num Test_Description Status Remaining
} LifeTime(hours)
} > LBA_of_first_error
} > # 1 Extended offline Interrupted (host reset) 50% 23726
} > -
} > # 2 Extended offline Completed without error 00% 22580
} > -
} > # 3 Short offline Completed without error 00% 22577
} > -
} > # 4 Extended offline Completed without error 00% 17267
} > -
} > # 5 Short offline Completed without error 00% 17260
} > -
} > # 6 Extended offline Completed without error 00% 384
} > -
} >
} > SMART Selective self-test log data structure revision number 1
} > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
} > 1 0 0 Not_testing
} > 2 0 0 Not_testing
} > 3 0 0 Not_testing
} > 4 0 0 Not_testing
} > 5 0 0 Not_testing
} > Selective self-test flags (0x0):
} > After scanning selected spans, do NOT read-scan remainder of disk.
} > If Selective self-test is pending on power-up, resume after 0 minute
} delay.
} >
} > # smartctl -a /dev/sdc
} > smartctl version 5.38 [i386-redhat-linux-gnu] Copyright (C) 2002-8 Bruce
} > Allen
} > Home page is http://smartmontools.sourceforge.net/
} >
} > === START OF INFORMATION SECTION ===
} > Model Family: Seagate Barracuda 7200.10 family
} > Device Model: ST3320620AS
} > Serial Number: 3QF08V24
} > Firmware Version: 3.AAD
} > User Capacity: 320,072,933,376 bytes
} > Device is: In smartctl database [for details use: -P show]
} > ATA Version is: 7
} > ATA Standard is: Exact ATA specification draft version not indicated
} > Local Time is: Wed Nov 11 00:03:36 2009 EST
} > SMART support is: Available - device has SMART capability.
} > SMART support is: Enabled
} >
} > === START OF READ SMART DATA SECTION ===
} > SMART overall-health self-assessment test result: PASSED
} > See vendor-specific Attribute list for marginal Attributes.
} >
} > General SMART Values:
} > Offline data collection status: (0x82) Offline data collection activity
} > was completed without error.
} > Auto Offline Data Collection:
} > Enabled.
} > Self-test execution status: ( 0) The previous self-test routine
} > completed
} > without error or no self-test has
} > ever
} > been run.
} > Total time to complete Offline
} > data collection: ( 430) seconds.
} > Offline data collection
} > capabilities: (0x5b) SMART execute Offline immediate.
} > Auto Offline data collection
} on/off
} > support.
} > Suspend Offline collection upon
} new
} > command.
} > Offline surface scan supported.
} > Self-test supported.
} > No Conveyance Self-test
} supported.
} > Selective Self-test supported.
} > SMART capabilities: (0x0003) Saves SMART data before entering
} > power-saving mode.
} > Supports SMART auto save timer.
} > Error logging capability: (0x01) Error logging supported.
} > General Purpose Logging
} supported.
} > Short self-test routine
} > recommended polling time: ( 1) minutes.
} > Extended self-test routine
} > recommended polling time: ( 115) minutes.
} >
} > SMART Attributes Data Structure revision number: 10
} > Vendor Specific SMART Attributes with Thresholds:
} > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
} UPDATED
} > WHEN_FAILED RAW_VALUE
} > 1 Raw_Read_Error_Rate 0x000f 119 090 006 Pre-fail Always
} > - 221110249
} > 3 Spin_Up_Time 0x0003 094 090 000 Pre-fail Always
} > - 0
} > 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
} > - 94
} > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
} > - 0
} > 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always
} > - 138219006
} > 9 Power_On_Hours 0x0032 073 073 000 Old_age Always
} > - 23917
} > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
} > - 0
} > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
} > - 130
} > 187 Reported_Uncorrect 0x0032 082 082 000 Old_age Always
} > - 18
} > 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
} > - 0
} > 190 Airflow_Temperature_Cel 0x0022 059 044 045 Old_age Always
} > In_the_past 41 (Lifetime Min/Max 39/45)
} > 194 Temperature_Celsius 0x0022 041 056 000 Old_age Always
} > - 41 (0 22 0 0)
} > 195 Hardware_ECC_Recovered 0x001a 066 057 000 Old_age Always
} > - 145841009
} > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
} > - 0
} > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
} Offline
} > - 0
} > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
} > - 0
} > 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
} Offline
} > - 0
} > 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
} > - 0
} >
} > SMART Error Log Version: 1
} > ATA Error Count: 18 (device log contains only the most recent five
} errors)
} > CR = Command Register [HEX]
} > FR = Features Register [HEX]
} > SC = Sector Count Register [HEX]
} > SN = Sector Number Register [HEX]
} > CL = Cylinder Low Register [HEX]
} > CH = Cylinder High Register [HEX]
} > DH = Device/Head Register [HEX]
} > DC = Device Command Register [HEX]
} > ER = Error register [HEX]
} > ST = Status register [HEX]
} > Powered_Up_Time is measured from power on, and printed as
} > DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
} > SS=sec, and sss=millisec. It "wraps" after 49.710 days.
} >
} > Error 18 occurred at disk power-on lifetime: 5380 hours (224 days + 4
} hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 63 81 09 e0 Error: UNC at LBA = 0x00098163 = 622947
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 e1 7e 09 e0 00 00:16:26.026 READ DMA EXT
} > ec 00 00 00 00 00 a0 00 00:16:26.022 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:16:26.022 SET FEATURES [Set transfer
} > mode]
} > ec 00 00 00 00 00 a0 00 00:16:26.019 IDENTIFY DEVICE
} > 25 00 00 e1 7e 09 e0 00 00:16:24.456 READ DMA EXT
} >
} > Error 17 occurred at disk power-on lifetime: 5380 hours (224 days + 4
} hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 63 81 09 e0 Error: UNC at LBA = 0x00098163 = 622947
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 e1 7e 09 e0 00 00:16:21.313 READ DMA EXT
} > ec 00 00 00 00 00 a0 00 00:16:19.753 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:16:19.749 SET FEATURES [Set transfer
} > mode]
} > ec 00 00 00 00 00 a0 00 00:16:19.749 IDENTIFY DEVICE
} > 25 00 00 e1 7e 09 e0 00 00:16:24.456 READ DMA EXT
} >
} > Error 16 occurred at disk power-on lifetime: 5380 hours (224 days + 4
} hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 63 81 09 e0 Error: UNC at LBA = 0x00098163 = 622947
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 e1 7e 09 e0 00 00:16:21.313 READ DMA EXT
} > ec 00 00 00 00 00 a0 00 00:16:19.753 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:16:19.749 SET FEATURES [Set transfer
} > mode]
} > ec 00 00 00 00 00 a0 00 00:16:19.749 IDENTIFY DEVICE
} > 25 00 00 e1 7e 09 e0 00 00:16:19.745 READ DMA EXT
} >
} > Error 15 occurred at disk power-on lifetime: 5380 hours (224 days + 4
} hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 63 81 09 e0 Error: UNC at LBA = 0x00098163 = 622947
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 e1 7e 09 e0 00 00:16:21.313 READ DMA EXT
} > ec 00 00 00 00 00 a0 00 00:16:19.753 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:16:19.749 SET FEATURES [Set transfer
} > mode]
} > ec 00 00 00 00 00 a0 00 00:16:19.749 IDENTIFY DEVICE
} > 25 00 00 e1 7e 09 e0 00 00:16:19.745 READ DMA EXT
} >
} > Error 14 occurred at disk power-on lifetime: 5380 hours (224 days + 4
} hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 63 81 09 e0 Error: UNC at LBA = 0x00098163 = 622947
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 e1 7e 09 e0 00 00:16:17.672 READ DMA EXT
} > ec 00 00 00 00 00 a0 00 00:16:19.753 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:16:19.749 SET FEATURES [Set transfer
} > mode]
} > ec 00 00 00 00 00 a0 00 00:16:19.749 IDENTIFY DEVICE
} > 25 00 00 e1 7e 09 e0 00 00:16:19.745 READ DMA EXT
} >
} > SMART Self-test log structure revision number 1
} > Num Test_Description Status Remaining
} LifeTime(hours)
} > LBA_of_first_error
} > # 1 Extended offline Completed without error 00% 23728
} > -
} > # 2 Extended offline Completed without error 00% 22579
} > -
} > # 3 Short offline Completed without error 00% 22576
} > -
} > # 4 Extended offline Completed without error 00% 17265
} > -
} > # 5 Short offline Completed without error 00% 17257
} > -
} > # 6 Extended offline Completed without error 00% 384
} > -
} >
} > SMART Selective self-test log data structure revision number 1
} > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
} > 1 0 0 Not_testing
} > 2 0 0 Not_testing
} > 3 0 0 Not_testing
} > 4 0 0 Not_testing
} > 5 0 0 Not_testing
} > Selective self-test flags (0x0):
} > After scanning selected spans, do NOT read-scan remainder of disk.
} > If Selective self-test is pending on power-up, resume after 0 minute
} delay.
} >
} > # smartctl -a /dev/sdd
} > smartctl version 5.38 [i386-redhat-linux-gnu] Copyright (C) 2002-8 Bruce
} > Allen
} > Home page is http://smartmontools.sourceforge.net/
} >
} > === START OF INFORMATION SECTION ===
} > Model Family: Seagate Barracuda 7200.10 family
} > Device Model: ST3320620AS
} > Serial Number: 3QF08WDP
} > Firmware Version: 3.AAD
} > User Capacity: 320,072,933,376 bytes
} > Device is: In smartctl database [for details use: -P show]
} > ATA Version is: 7
} > ATA Standard is: Exact ATA specification draft version not indicated
} > Local Time is: Wed Nov 11 00:04:04 2009 EST
} > SMART support is: Available - device has SMART capability.
} > SMART support is: Enabled
} >
} > === START OF READ SMART DATA SECTION ===
} > SMART overall-health self-assessment test result: PASSED
} >
} > General SMART Values:
} > Offline data collection status: (0x82) Offline data collection activity
} > was completed without error.
} > Auto Offline Data Collection:
} > Enabled.
} > Self-test execution status: ( 0) The previous self-test routine
} > completed
} > without error or no self-test has
} > ever
} > been run.
} > Total time to complete Offline
} > data collection: ( 430) seconds.
} > Offline data collection
} > capabilities: (0x5b) SMART execute Offline immediate.
} > Auto Offline data collection
} on/off
} > support.
} > Suspend Offline collection upon
} new
} > command.
} > Offline surface scan supported.
} > Self-test supported.
} > No Conveyance Self-test
} supported.
} > Selective Self-test supported.
} > SMART capabilities: (0x0003) Saves SMART data before entering
} > power-saving mode.
} > Supports SMART auto save timer.
} > Error logging capability: (0x01) Error logging supported.
} > General Purpose Logging
} supported.
} > Short self-test routine
} > recommended polling time: ( 1) minutes.
} > Extended self-test routine
} > recommended polling time: ( 115) minutes.
} >
} > SMART Attributes Data Structure revision number: 10
} > Vendor Specific SMART Attributes with Thresholds:
} > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
} UPDATED
} > WHEN_FAILED RAW_VALUE
} > 1 Raw_Read_Error_Rate 0x000f 110 090 006 Pre-fail Always
} > - 25809154
} > 3 Spin_Up_Time 0x0003 098 090 000 Pre-fail Always
} > - 0
} > 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
} > - 516
} > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always
} > - 0
} > 7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail Always
} > - 192909989
} > 9 Power_On_Hours 0x0032 073 073 000 Old_age Always
} > - 23896
} > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
} > - 0
} > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
} > - 777
} > 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
} > - 0
} > 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
} > - 0
} > 190 Airflow_Temperature_Cel 0x0022 061 050 045 Old_age Always
} > - 39 (Lifetime Min/Max 36/42)
} > 194 Temperature_Celsius 0x0022 039 050 000 Old_age Always
} > - 39 (0 20 0 0)
} > 195 Hardware_ECC_Recovered 0x001a 064 055 000 Old_age Always
} > - 81546876
} > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
} > - 0
} > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
} Offline
} > - 0
} > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
} > - 0
} > 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
} Offline
} > - 0
} > 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
} > - 0
} >
} > SMART Error Log Version: 1
} > ATA Error Count: 6 (device log contains only the most recent five
} errors)
} > CR = Command Register [HEX]
} > FR = Features Register [HEX]
} > SC = Sector Count Register [HEX]
} > SN = Sector Number Register [HEX]
} > CL = Cylinder Low Register [HEX]
} > CH = Cylinder High Register [HEX]
} > DH = Device/Head Register [HEX]
} > DC = Device Command Register [HEX]
} > ER = Error register [HEX]
} > ST = Status register [HEX]
} > Powered_Up_Time is measured from power on, and printed as
} > DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
} > SS=sec, and sss=millisec. It "wraps" after 49.710 days.
} >
} > Error 6 occurred at disk power-on lifetime: 10007 hours (416 days + 23
} > hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 a5 0d 4a e0 Error: UNC at LBA = 0x004a0da5 = 4853157
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 8f 0c 4a e0 00 00:05:45.657 READ DMA EXT
} > 27 00 00 00 00 00 e0 00 00:05:45.654 READ NATIVE MAX ADDRESS EXT
} > ec 00 00 00 00 00 a0 00 00:05:43.727 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:05:43.660 SET FEATURES [Set transfer
} > mode]
} > 27 00 00 00 00 00 e0 00 00:05:43.658 READ NATIVE MAX ADDRESS EXT
} >
} > Error 5 occurred at disk power-on lifetime: 10007 hours (416 days + 23
} > hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 a5 0d 4a e0 Error: UNC at LBA = 0x004a0da5 = 4853157
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 8f 0c 4a e0 00 00:05:45.657 READ DMA EXT
} > 27 00 00 00 00 00 e0 00 00:05:45.654 READ NATIVE MAX ADDRESS EXT
} > ec 00 00 00 00 00 a0 00 00:05:43.727 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:05:43.660 SET FEATURES [Set transfer
} > mode]
} > 27 00 00 00 00 00 e0 00 00:05:43.658 READ NATIVE MAX ADDRESS EXT
} >
} > Error 4 occurred at disk power-on lifetime: 10007 hours (416 days + 23
} > hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 a5 0d 4a e0 Error: UNC at LBA = 0x004a0da5 = 4853157
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 8f 0c 4a e0 00 00:05:39.547 READ DMA EXT
} > 27 00 00 00 00 00 e0 00 00:05:39.544 READ NATIVE MAX ADDRESS EXT
} > ec 00 00 00 00 00 a0 00 00:05:43.727 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:05:43.660 SET FEATURES [Set transfer
} > mode]
} > 27 00 00 00 00 00 e0 00 00:05:43.658 READ NATIVE MAX ADDRESS EXT
} >
} > Error 3 occurred at disk power-on lifetime: 10007 hours (416 days + 23
} > hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 a5 0d 4a e0 Error: UNC at LBA = 0x004a0da5 = 4853157
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 8f 0c 4a e0 00 00:05:39.547 READ DMA EXT
} > 27 00 00 00 00 00 e0 00 00:05:39.544 READ NATIVE MAX ADDRESS EXT
} > ec 00 00 00 00 00 a0 00 00:05:39.530 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:05:39.475 SET FEATURES [Set transfer
} > mode]
} > 27 00 00 00 00 00 e0 00 00:05:39.472 READ NATIVE MAX ADDRESS EXT
} >
} > Error 2 occurred at disk power-on lifetime: 10007 hours (416 days + 23
} > hours)
} > When the command that caused the error occurred, the device was active
} or
} > idle.
} >
} > After command completion occurred, registers were:
} > ER ST SC SN CL CH DH
} > -- -- -- -- -- -- --
} > 40 51 00 a5 0d 4a e0 Error: UNC at LBA = 0x004a0da5 = 4853157
} >
} > Commands leading to the command that caused the error were:
} > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
} > -- -- -- -- -- -- -- -- ---------------- --------------------
} > 25 00 00 8f 0c 4a e0 00 00:05:39.547 READ DMA EXT
} > 27 00 00 00 00 00 e0 00 00:05:39.544 READ NATIVE MAX ADDRESS EXT
} > ec 00 00 00 00 00 a0 00 00:05:39.530 IDENTIFY DEVICE
} > ef 03 46 00 00 00 a0 00 00:05:39.475 SET FEATURES [Set transfer
} > mode]
} > 27 00 00 00 00 00 e0 00 00:05:39.472 READ NATIVE MAX ADDRESS EXT
} >
} > SMART Self-test log structure revision number 1
} > Num Test_Description Status Remaining
} LifeTime(hours)
} > LBA_of_first_error
} > # 1 Extended offline Completed without error 00% 23707
} > -
} > # 2 Extended offline Completed without error 00% 22559
} > -
} > # 3 Short offline Completed without error 00% 22555
} > -
} > # 4 Extended offline Completed without error 00% 17248
} > -
} > # 5 Short offline Completed without error 00% 17241
} > -
} > # 6 Short offline Completed without error 00% 17241
} > -
} > # 7 Extended offline Completed without error 00% 384
} > -
} > # 8 Short offline Completed without error 00% 381
} > -
} >
} > SMART Selective self-test log data structure revision number 1
} > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
} > 1 0 0 Not_testing
} > 2 0 0 Not_testing
} > 3 0 0 Not_testing
} > 4 0 0 Not_testing
} > 5 0 0 Not_testing
} > Selective self-test flags (0x0):
} > After scanning selected spans, do NOT read-scan remainder of disk.
} > If Selective self-test is pending on power-up, resume after 0 minute
} delay.
} >
} > Thanks,
} > Guy
} >
} > --
} > To unsubscribe from this list: send the line "unsubscribe linux-raid" in
} > the body of a message to majordomo@vger.kernel.org
} > More majordomo info at http://vger.kernel.org/majordomo-info.html
} >
}
}
}
} --
} Majed B.
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2009-11-11 7:01 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-11-11 5:37 RAID6 array lost a disk, can someone decode the error? Guy Watkins
2009-11-11 5:52 ` Majed B.
2009-11-11 7:01 ` Guy Watkins [this message]
2009-11-11 7:08 ` Thomas Fjellstrom
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CA641DF8B4814BD390BF8BC522B55AB4@m5 \
--to=guy@watkins-home.com \
--cc=linux-raid@vger.kernel.org \
--cc=majedb@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox