Re: [PATCH 08/17] remoteproc/omap: Add support for DRA7xx remote processors

Bjorn Andersson
2019-11-11T23:37:10Z

On Mon 28 Oct 05:42 PDT 2019, Tero Kristo wrote:

> From: Suman Anna <s-anna@ti.com>
>
> DRA7xx/AM57xx SoCs have two IPU and up to two DSP processor subsystems
> for offloading different computation algorithms. The IPU processor
> subsystem contains dual-core ARM Cortex-M4 processors, and is very
> similar to those on OMAP5. The DSP processor subsystem is based on
> the TI's standard TMS320C66x DSP CorePac core.
>
> Support has been added to the OMAP remoteproc driver through new
> DRA7xx specific compatibles for properly probing and booting the
> all the different processor subsystem instances on DRA7xx/AM57xx
> SoCs - IPU1, IPU2, DSP1 & DSP2. A build dependency with SOC_DRA7XX
> is added to enable the driver to be built in DRA7xx-only configuration.
>
> The DSP boot address programming needed enhancement for DRA7xx as the
> boot register fields are different on DRA7 compared to OMAP4 and OMAP5
> SoCs. The register on DRA7xx contains additional fields within the
> register and the boot address bit-field is right-shifted by 10 bits.
> The internal memory parsing logic has also been updated to compute
> the device addresses for the L2 RAM for DSP devices using relative
> addressing logic, and to parse two additional RAMs at L1 level - L1P
> and L1D. This allows the remoteproc driver to support loading into
> these regions for a small subset of firmware images requiring as
> such. The most common usage would be to use the L1 programmable
> RAMs as L1 Caches.
>
> The firmware lookup logic also has to be adjusted for DRA7xx as
> there are (can be) more than one instance of both the IPU and DSP
> remote processors for the first time in OMAP4+ SoCs.
>
> The names for the firmware images are fixed for each processor and
> are expected to be as follows:
> IPU1: dra7-ipu1-fw.xem4
> IPU2: dra7-ipu2-fw.xem4
> DSP1: dra7-dsp1-fw.xe66
> DSP2: dra7-dsp2-fw.xe66
>
> Signed-off-by: Suman Anna <s-anna@ti.com>
> [t-kristo@ti.com: fixed l4_offset calculation logic]
> Signed-off-by: Tero Kristo <t-kristo@ti.com>
> ---
> drivers/remoteproc/Kconfig | 2 +-
> drivers/remoteproc/omap_remoteproc.c | 103 ++++++++++++++++++++++++---
> 2 files changed, 96 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
> index 94afdde4bc9f..d6450d7fcf92 100644
> --- a/drivers/remoteproc/Kconfig
> +++ b/drivers/remoteproc/Kconfig
> @@ -25,7 +25,7 @@ config IMX_REMOTEPROC
>
> config OMAP_REMOTEPROC
> tristate "OMAP remoteproc support"
> - depends on ARCH_OMAP4 || SOC_OMAP5
> + depends on ARCH_OMAP4 || SOC_OMAP5 || SOC_DRA7XX
> depends on OMAP_IOMMU
> select MAILBOX
> select OMAP2PLUS_MBOX
> diff --git a/drivers/remoteproc/omap_remoteproc.c b/drivers/remoteproc/omap_remoteproc.c
> index 0b80570effee..e46bb4c790d7 100644
> --- a/drivers/remoteproc/omap_remoteproc.c
> +++ b/drivers/remoteproc/omap_remoteproc.c
> @@ -17,6 +17,7 @@
> #include <linux/module.h>
> #include <linux/err.h>
> #include <linux/of_device.h>
> +#include <linux/of_address.h>
> #include <linux/of_reserved_mem.h>
> #include <linux/platform_device.h>
> #include <linux/dma-mapping.h>
> @@ -30,16 +31,20 @@
> #include "omap_remoteproc.h"
> #include "remoteproc_internal.h"
>
> +#define OMAP_RPROC_DSP_LOCAL_MEM_OFFSET (0x00800000)
> #define OMAP_RPROC_IPU_L2RAM_DEV_ADDR (0x20000000)
>
> /**
> * struct omap_rproc_boot_data - boot data structure for the DSP omap rprocs
> * @syscon: regmap handle for the system control configuration module
> * @boot_reg: boot register offset within the @syscon regmap
> + * @boot_reg_shift: bit-field shift required for the boot address value in
> + * @boot_reg
> */
> struct omap_rproc_boot_data {
> struct regmap *syscon;
> unsigned int boot_reg;
> + unsigned int boot_reg_shift;
> };
>
> /*
> @@ -151,14 +156,19 @@ static int omap_rproc_write_dsp_boot_addr(struct rproc *rproc)
> struct omap_rproc *oproc = rproc->priv;
> struct omap_rproc_boot_data *bdata = oproc->boot_data;
> u32 offset = bdata->boot_reg;
> + unsigned int value = rproc->bootaddr;
> + unsigned int mask = ~(SZ_1K - 1);
>
> - if (rproc->bootaddr & (SZ_1K - 1)) {
> + if (value & (SZ_1K - 1)) {

I would prefer if you keep this as it was.

> dev_err(dev, "invalid boot address 0x%x, must be aligned on a 1KB boundary\n",
> - rproc->bootaddr);
> + value);

Ditto.

> return -EINVAL;
> }
>
> - regmap_write(bdata->syscon, offset, rproc->bootaddr);
> + value >>= bdata->boot_reg_shift;
> + mask >>= bdata->boot_reg_shift;

And then

value = rproc->bootaddr >> bdata->boot_reg_shift;
mask = ~((SZ_1K - 1) >> bdata->boot_reg_shift);

Note though that this would make the upper boot_reg_shift bits 1, while
in your case they are 0s.

> +
> + regmap_update_bits(bdata->syscon, offset, mask, value);
>
> return 0;
> }
> @@ -292,6 +302,28 @@ static const struct omap_rproc_dev_data omap5_ipu_dev_data = {
> .fw_name = "omap5-ipu-fw.xem4",
> };
>
> +static const struct omap_rproc_dev_data dra7_rproc_dev_data[] = {
> + {
> + .device_name = "40800000.dsp",
> + .fw_name = "dra7-dsp1-fw.xe66",
> + },
> + {
> + .device_name = "41000000.dsp",
> + .fw_name = "dra7-dsp2-fw.xe66",
> + },
> + {
> + .device_name = "55020000.ipu",
> + .fw_name = "dra7-ipu2-fw.xem4",
> + },
> + {
> + .device_name = "58820000.ipu",
> + .fw_name = "dra7-ipu1-fw.xem4",
> + },
> + {
> + /* sentinel */
> + },
> +};
> +
> static const struct of_device_id omap_rproc_of_match[] = {
> {
> .compatible = "ti,omap4-dsp",
> @@ -309,6 +341,14 @@ static const struct of_device_id omap_rproc_of_match[] = {
> .compatible = "ti,omap5-ipu",
> .data = &omap5_ipu_dev_data,
> },
> + {
> + .compatible = "ti,dra7-dsp",
> + .data = dra7_rproc_dev_data,
> + },
> + {
> + .compatible = "ti,dra7-ipu",
> + .data = dra7_rproc_dev_data,
> + },
> {
> /* end */
> },
> @@ -317,13 +357,23 @@ MODULE_DEVICE_TABLE(of, omap_rproc_of_match);
>
> static const char *omap_rproc_get_firmware(struct platform_device *pdev)
> {
> + struct device_node *np = pdev->dev.of_node;
> const struct omap_rproc_dev_data *data;
>
> data = of_device_get_match_data(&pdev->dev);
> if (!data)
> return ERR_PTR(-ENODEV);
>
> - return data->fw_name;
> + if (!of_device_is_compatible(np, "ti,dra7-dsp") &&
> + !of_device_is_compatible(np, "ti,dra7-ipu"))
> + return data->fw_name;
> +
> + for (; data && data->device_name; data++) {
> + if (!strcmp(dev_name(&pdev->dev), data->device_name))

I don't fancy the reliance on node names in devicetree, is this well
defined in the binding?

> + return data->fw_name;
> + }
> +
> + return ERR_PTR(-ENOENT);
> }
>
> static int omap_rproc_get_boot_data(struct platform_device *pdev,
> @@ -334,7 +384,8 @@ static int omap_rproc_get_boot_data(struct platform_device *pdev,
> int ret;
>
> if (!of_device_is_compatible(np, "ti,omap4-dsp") &&
> - !of_device_is_compatible(np, "ti,omap5-dsp"))
> + !of_device_is_compatible(np, "ti,omap5-dsp") &&
> + !of_device_is_compatible(np, "ti,dra7-dsp"))
> return 0;
>
> oproc->boot_data = devm_kzalloc(&pdev->dev, sizeof(*oproc->boot_data),
> @@ -360,18 +411,27 @@ static int omap_rproc_get_boot_data(struct platform_device *pdev,
> return -EINVAL;
> }
>
> + if (of_device_is_compatible(np, "ti,dra7-dsp"))
> + oproc->boot_data->boot_reg_shift = 10;

Put this in omap_rproc_dev_data.

> +
> return 0;
> }
>
> static int omap_rproc_of_get_internal_memories(struct platform_device *pdev,
> struct rproc *rproc)
> {
> - static const char * const mem_names[] = {"l2ram"};
> + static const char * const ipu_mem_names[] = {"l2ram"};
> + static const char * const dra7_dsp_mem_names[] = {"l2ram", "l1pram",
> + "l1dram"};
> struct device_node *np = pdev->dev.of_node;
> struct omap_rproc *oproc = rproc->priv;
> struct device *dev = &pdev->dev;
> + const char * const *mem_names;
> struct resource *res;
> int num_mems;
> + const __be32 *addrp;
> + u32 l4_offset = 0;
> + u64 size;
> int i;
>
> /* OMAP4 and OMAP5 DSPs do not have support for flat SRAM */
> @@ -379,7 +439,15 @@ static int omap_rproc_of_get_internal_memories(struct platform_device *pdev,
> of_device_is_compatible(np, "ti,omap5-dsp"))
> return 0;
>
> - num_mems = ARRAY_SIZE(mem_names);
> + /* DRA7 DSPs have two additional SRAMs at L1 level */
> + if (of_device_is_compatible(np, "ti,dra7-dsp")) {
> + mem_names = dra7_dsp_mem_names;
> + num_mems = ARRAY_SIZE(dra7_dsp_mem_names);
> + } else {
> + mem_names = ipu_mem_names;
> + num_mems = ARRAY_SIZE(ipu_mem_names);
> + }
> +
> oproc->mem = devm_kcalloc(dev, num_mems, sizeof(*oproc->mem),
> GFP_KERNEL);
> if (!oproc->mem)
> @@ -395,7 +463,26 @@ static int omap_rproc_of_get_internal_memories(struct platform_device *pdev,
> return PTR_ERR(oproc->mem[i].cpu_addr);
> }
> oproc->mem[i].bus_addr = res->start;
> - oproc->mem[i].dev_addr = OMAP_RPROC_IPU_L2RAM_DEV_ADDR;
> +
> + /*
> + * The DSPs have the internal memories starting at a fixed
> + * offset of 0x800000 from address 0, and this corresponds to
> + * L2RAM. The L3 address view has the L2RAM bus address as the
> + * starting address for the IP, so the L2RAM memory region needs
> + * to be processed first, and the device addresses for each
> + * memory region can be computed using the relative offset
> + * from this base address.
> + */
> + if (of_device_is_compatible(np, "ti,dra7-dsp") &&

Please don't use a ternary operator repeatedly, it makes the code hard
to follow.

Regards,
Bjorn

> + !strcmp(mem_names[i], "l2ram")) {
> + addrp = of_get_address(dev->of_node, i, &size, NULL);
> + l4_offset = of_translate_address(dev->of_node, addrp);
> + }
> + oproc->mem[i].dev_addr =
> + of_device_is_compatible(np, "ti,dra7-dsp") ?
> + res->start - l4_offset +
> + OMAP_RPROC_DSP_LOCAL_MEM_OFFSET :
> + OMAP_RPROC_IPU_L2RAM_DEV_ADDR;
> oproc->mem[i].size = resource_size(res);
>
> dev_dbg(dev, "memory %8s: bus addr %pa size 0x%x va %p da 0x%x\n",
> --
> 2.17.1
>
> --
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki