Re: [net-next,v2] net: phy: marvell-88q2xxx: Enable temperature sensor for mv88q211x

[Heiner Kallweit <hkallweit1@gmail.com>]

On 18.04.2025 16:58, Niklas Söderlund wrote:
> The temperature sensor enabled for mv88q222x devices also functions for
> mv88q211x based devices. Unify the two devices probe functions to enable
> the sensors for all devices supported by this driver.
> 
> The same oddity as for mv88q222x devices exists, the PHY link must be up
> for a correct temperature reading to be reported.
> 
>     # cat /sys/class/hwmon/hwmon9/temp1_input
>     -75000
> 
>     # ifconfig end5 up
> 
>     # cat /sys/class/hwmon/hwmon9/temp1_input
>     59000
> 
> Worth noting is that while the temperature register offsets and layout
> are the same between mv88q211x and mv88q222x devices their names in the
> datasheets are different. This change keeps the mv88q222x names for the
> mv88q211x support.
> 
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> Reviewed-by: Dimitri Fedrau <dima.fedrau@gmail.com>
> ---
> * Changes since v1
> - Clarify in commit message that it's the link that must be up for the
>   reporting to work, not just power up. Hopefully this oddity can be
>   solved in the future by patch [1].
> 
Following this link I don't see anything which would deal with incorrect
values being shown if link is down. What are you referring to in detail?
I think you have to modify mv88q2xxx_hwmon_is_visible(), or return an
appropriate error in mv88q2xxx_hwmon_read() if link is down.

>   This change just aligns the mv88q211x with the current mv88q222x
>   behavior.
> 
> 1. https://lore.kernel.org/all/20250220-marvell-88q2xxx-hwmon-enable-at-probe-v2-0-78b2838a62da@gmail.com/
> ---
>  drivers/net/phy/marvell-88q2xxx.c | 14 ++------------
>  1 file changed, 2 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/net/phy/marvell-88q2xxx.c b/drivers/net/phy/marvell-88q2xxx.c
> index 23e1f0521f54..5c687164b8e0 100644
> --- a/drivers/net/phy/marvell-88q2xxx.c
> +++ b/drivers/net/phy/marvell-88q2xxx.c
> @@ -828,6 +828,7 @@ static int mv88q2xxx_leds_probe(struct phy_device *phydev)
>  static int mv88q2xxx_probe(struct phy_device *phydev)
>  {
>  	struct mv88q2xxx_priv *priv;
> +	int ret;
>  
>  	priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
>  	if (!priv)
> @@ -835,17 +836,6 @@ static int mv88q2xxx_probe(struct phy_device *phydev)
>  
>  	phydev->priv = priv;
>  
> -	return 0;
> -}
> -
> -static int mv88q222x_probe(struct phy_device *phydev)
> -{
> -	int ret;
> -
> -	ret = mv88q2xxx_probe(phydev);
> -	if (ret)
> -		return ret;
> -
>  	ret = mv88q2xxx_leds_probe(phydev);
>  	if (ret)
>  		return ret;
> @@ -1118,7 +1108,7 @@ static struct phy_driver mv88q2xxx_driver[] = {
>  		.phy_id_mask		= MARVELL_PHY_ID_MASK,
>  		.name			= "mv88q2220",
>  		.flags			= PHY_POLL_CABLE_TEST,
> -		.probe			= mv88q222x_probe,
> +		.probe			= mv88q2xxx_probe,
>  		.get_features		= mv88q2xxx_get_features,
>  		.config_aneg		= mv88q2xxx_config_aneg,
>  		.aneg_done		= genphy_c45_aneg_done,