Re: [PATCH 6/6] arm64: dts: renesas: rzt2h-n2h-evk: Enable USB2.0 support

["Lad, Prabhakar" <prabhakar.csengg@gmail.com>]

Hi Geert,

Thank you for the review.

On Wed, Sep 3, 2025 at 4:04 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Thu, 21 Aug 2025 at 18:19, Prabhakar <prabhakar.csengg@gmail.com> wrote:
> > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> >
> > Enable USB2.0 support on RZ/T2H and RZ/N2H EVKs.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
>
> Thanks for your patch!
>
> > --- a/arch/arm64/boot/dts/renesas/r9a09g077m44-rzt2h-evk.dts
> > +++ b/arch/arm64/boot/dts/renesas/r9a09g077m44-rzt2h-evk.dts
> > @@ -29,6 +29,28 @@
> >   */
> >  #define SD1_MICRO_SD   1
> >
> > +/*
> > + * USB Pin Configuration:
> > + *
> > + * This board is equipped with three USB connectors: Type-A (CN80), Mini-B (CN79),
> > + * and Micro-AB (CN33). The RZ/T2H SoC has a single USB channel, so either the USB
> > + * host interface or the USB function interface can be used, but not both at the
> > + * same time.
>
> Please reflow the text to fit in 80 columns.
>
Ok, I will reflow it to 80 columns
> The last sentence applies to the CN80 and CN79 connectors only, right?
>
Yes,  I'll reword it to say `but not both at the same time while using
CN79 and CN80 connectors.`

> > + *
> > + * By default, the Type-A (CN80) and Mini-B (CN79) connectors are enabled.
> > + * Configure the switches as follows:
> > + *   - P00_0 - P00_2 (control signals for USB power supply): SW1[5] = ON
> > + *   - USB_VBUSIN (used for USB function): SW7[7] = OFF; SW7[8] = ON
> > + *   - USB_VBUSEN (used for USB_HF_VBUSEN): SW7[9] = OFF; SW7[10] = ON
> > + *
> > + * To enable the Micro-AB (CN33) USB OTG connector, set the following macro to 1
> > + * and configure the switches as follows:
> > + *   - P00_0 - P00_2 (control signals for USB power supply): SW1[5] = ON
> > + *   - USB_VBUSIN (used for USB OTG): SW7[7] = ON; SW7[8] = OFF
> > + *   - USB_VBUSEN (used for USB_OTG_VBUSEN): SW7[9] = ON; SW7[10] = OFF
> > + */
> > +#define USB_OTG                0
> > +
> >  #include "rzt2h-n2h-evk-common.dtsi"
> >
> >  / {
> > @@ -145,4 +167,18 @@ i2c1_pins: i2c1-pins {
> >                 pinmux = <RZT2H_PORT_PINMUX(5, 0, 0x17)>, /* SDA */
> >                          <RZT2H_PORT_PINMUX(4, 7, 0x17)>; /* SCL */
> >         };
> > +
> > +#if USB_OTG
> > +       usb-exicen-hog {
> > +               gpio-hog;
> > +               gpios = <RZT2H_GPIO(0, 2) GPIO_ACTIVE_HIGH>;
> > +               output-high;
> > +               line-name = "usb_exicen_a";
> > +       };
> > +#endif
> > +
> > +       usb_pins: usb-pins {
> > +               pinmux = <RZT2H_PORT_PINMUX(0, 0, 0x13)>, /* VBUS */
>
> s/VBUS/VBUSEN/?
>
OK.

> > +                        <RZT2H_PORT_PINMUX(0, 1, 0x13)>; /* OVRCUR */
> > +       };
> >  };
> > diff --git a/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts b/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts
> > index 80f358fb2d74..b98b0f7c1128 100644
> > --- a/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts
> > +++ b/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts
> > @@ -33,6 +33,33 @@
> >   */
> >  #define SD1_MICRO_SD   1
> >
> > +/*
> > + * USB Pin Configuration:
> > + *
> > + * This board is equipped with three USB connectors: Type-A (CN7), Mini-B (CN8),
> > + * and Micro-AB (CN9). The RZ/N2H SoC has a single USB channel, so either the USB
> > + * host interface or the USB function interface can be used, but not both at the
> > + * same time.
>
> Please reflow the text to fit in 80 columns.
>
OK.

> The last sentence applies to the CN7 and CN8 connectors only, right?
>
Yes. I'll reword it to say `but not both at the same time while using
CN7 and CN8 connectors`

> > + *
> > + * By default, the Type-A (CN7) and Mini-B (CN8) connectors are enabled.
> > + * Configure the switches as follows:
> > + *   - P02_2 - P02_3 (control signals for USB power supply): DSW2[6] = OFF;
>
> s/DSW2[6]/DSW2[5]/?
>
The above is correct,

DSW2[5] is OFF, P00_0 to P00_2 are connected to BSC2(CN43) and GPT0(CN49).
DSW2[5] is ON, P00_0 to P00_2 are used as control signals for the USB
power-supply IC.

But we are using P02_2 and P02_3
DSW2[5] is OFF, P01_0, P01_2, P01_4 to P01_7, and P02_0 to P02_3 are
connected to ENCIF0(CN44) and GPT0(CN49), and used as control signals
for the USB power-supply IC.

> > + *     - P02_2 (used for VBUSEN): DSW14[5] = OFF; DSW14[6] = ON
> > + *     - P02_3 (used for USB_OVRCUR): DSW14[1] = OFF; DSW14[2] = ON
> > + *   - USB_VBUSIN (used for VBUS of CN8 for function): DSW16[1] = OFF; DSW16[2] = ON
> > + *   - USB_VBUSEN (used for USB_HF_VBUSEN): DSW16[3] = OFF; DSW16[4] = ON
> > + *
> > + * To enable the Micro-AB (CN9) USB OTG connector, set the following macro to 1
> > + * and configure the switches as follows:
> > + *   - P02_2 - P02_3 (control signals for USB power supply): DSW2[6] = OFF;
>
> s/DSW2[6]/DSW2[5]/?
>
ditto.

> > + *     - P02_2 (used for VBUSEN): DSW14[5] = OFF; DSW14[6] = ON
> > + *     - P02_3 (used for USB_OVRCUR): DSW14[1] = OFF; DSW14[2] = ON
> > + *   - USB_VBUSIN (used for VBUS of CN9 for OTG): DSW16[1] = ON; DSW16[2] = OFF
> > + *   - USB_VBUSEN (used for USB_OTG_VBUSEN): DSW16[3] = ON; DSW16[4] = OFF
> > + *   - USB_EXICEN (used for USB OTG EXICEN): DSW14[3] = OFF; DSW14[4] = ON
>
> Looks like you could use P00_0 - P00_2 instead of P02_2 - P02_3, like
> on the RZ/T2H EVK?
> But you don't want to do that because you want to use these pins for Ethernet?
>
Yes, I plan to use them for Ethernet.

> > + */
> > +#define USB_OTG                0
> > +
> >  #include "rzt2h-n2h-evk-common.dtsi"
> >
> >  /*
> > @@ -185,4 +212,18 @@ i2c1_pins: i2c1-pins {
> >                 pinmux = <RZT2H_PORT_PINMUX(3, 3, 0x17)>,
> >                          <RZT2H_PORT_PINMUX(3, 4, 0x17)>;
> >         };
> > +
> > +#if USB_OTG
> > +       usb-exicen-hog {
> > +               gpio-hog;
> > +               gpios = <RZT2H_GPIO(2, 4) GPIO_ACTIVE_HIGH>;
> > +               output-high;
> > +               line-name = "usb_exicen_a";
> > +       };
> > +#endif
> > +
> > +       usb_pins: usb-pins {
> > +               pinmux = <RZT2H_PORT_PINMUX(2, 2, 0x13)>, /* VBUS */
>
> s/VBUS/VBUSEN/?
>
OK.

Cheers,
Prabhakar