public inbox for linux-riscv@lists.infradead.org
 help / color / mirror / Atom feed
From: Rob Herring <robh@kernel.org>
To: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Albert Ou <aou@eecs.berkeley.edu>, Guo Ren <guoren@kernel.org>,
	Frank Rowand <frowand.list@gmail.com>,
	linux-riscv@lists.infradead.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, linux-arch@vger.kernel.org
Subject: Re: [PATCH v3] riscv: Use PUD/P4D/PGD pages for the linear mapping
Date: Tue, 13 Dec 2022 10:38:09 -0600	[thread overview]
Message-ID: <20221213163809.GA2016314-robh@kernel.org> (raw)
In-Reply-To: <20221213060204.27286-1-alexghiti@rivosinc.com>

On Tue, Dec 13, 2022 at 07:02:04AM +0100, Alexandre Ghiti wrote:
> During the early page table creation, we used to set the mapping for
> PAGE_OFFSET to the kernel load address: but the kernel load address is
> always offseted by PMD_SIZE which makes it impossible to use PUD/P4D/PGD
> pages as this physical address is not aligned on PUD/P4D/PGD size (whereas
> PAGE_OFFSET is).
> 
> But actually we don't have to establish this mapping (ie set va_pa_offset)
> that early in the boot process because:
> 
> - first, setup_vm installs a temporary kernel mapping and among other
>   things, discovers the system memory,
> - then, setup_vm_final creates the final kernel mapping and takes
>   advantage of the discovered system memory to create the linear
>   mapping.
> 
> During the first phase, we don't know the start of the system memory and
> then until the second phase is finished, we can't use the linear mapping at
> all and phys_to_virt/virt_to_phys translations must not be used because it
> would result in a different translation from the 'real' one once the final
> mapping is installed.
> 
> So here we simply delay the initialization of va_pa_offset to after the
> system memory discovery. But to make sure noone uses the linear mapping
> before, we add some guard in the DEBUG_VIRTUAL config.
> 
> Finally we can use PUD/P4D/PGD hugepages when possible, which will result
> in a better TLB utilization.
> 
> Note that we rely on the firmware to protect itself using PMP.
> 
> Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
> ---
> 
> v3:
> - Change the comment about initrd_start VA conversion so that it fits
>   ARM64 and RISCV64 (and others in the future if needed), as suggested
>   by Rob
> 
> v2:
> - Add a comment on why RISCV64 does not need to set initrd_start/end that
>   early in the boot process, as asked by Rob
> 
> Note that this patch is rebased on top of:
> [PATCH v1 1/1] riscv: mm: call best_map_size many times during linear-mapping
> 
>  arch/riscv/include/asm/page.h | 16 ++++++++++++++++
>  arch/riscv/mm/init.c          | 25 +++++++++++++++++++------
>  arch/riscv/mm/physaddr.c      | 16 ++++++++++++++++
>  drivers/of/fdt.c              | 11 ++++++-----

Acked-by: Rob Herring <robh@kernel.org> # DT bits

>  4 files changed, 57 insertions(+), 11 deletions(-)

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

  reply	other threads:[~2022-12-13 16:38 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-12-13  6:02 [PATCH v3] riscv: Use PUD/P4D/PGD pages for the linear mapping Alexandre Ghiti
2022-12-13 16:38 ` Rob Herring [this message]
2022-12-22 23:21 ` Conor Dooley
2022-12-28  1:36   ` Samuel Holland
2022-12-28  1:38 ` Samuel Holland

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20221213163809.GA2016314-robh@kernel.org \
    --to=robh@kernel.org \
    --cc=alexghiti@rivosinc.com \
    --cc=aou@eecs.berkeley.edu \
    --cc=devicetree@vger.kernel.org \
    --cc=frowand.list@gmail.com \
    --cc=guoren@kernel.org \
    --cc=linux-arch@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=palmer@dabbelt.com \
    --cc=paul.walmsley@sifive.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox