[PATCH v2 4/4] ARM: dts: sunxi: add MangoPi MQ-R-T113 board

[Andre Przywara <andre.przywara@arm.com>]

The MangoPi MQ-R-T113 is a small SBC with the Allwinner T113-s3 SoC.
The SoC features two Arm Cortex-A7 cores and 128 MB of co-packaged DDR3
DRAM. The board adds mostly connectors and the required regulators, plus
a Realtek RTL8189FTV WiFi chip.
Power comes in via a USB-C connector wired as a peripheral, and there is
a second USB-C connector usable as a host port.

Add a .dtsi file describing most of the board's peripherals, and include
that from the actual board .dts file. This allows to re-use the .dtsi
for the MQ-R-F113 RISC-V variant of that board.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../dts/sun8i-t113s-mangopi-mq-r-t113.dts     |  35 +++++
 .../boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi | 126 ++++++++++++++++++
 3 files changed, 162 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts
 create mode 100644 arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index efe4152e5846d..3367e24146da8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1397,6 +1397,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-s3-elimo-initium.dtb \
 	sun8i-s3-lichee-zero-plus.dtb \
 	sun8i-s3-pinecube.dtb \
+	sun8i-t113s-mangopi-mq-r-t113.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3-sl631-imx179.dtb \
 	sun8i-v3s-licheepi-zero.dtb \
diff --git a/arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts b/arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts
new file mode 100644
index 0000000000000..94e24b5926dd7
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-t113s-mangopi-mq-r-t113.dts
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+
+#include "sun8i-t113s.dtsi"
+#include "sunxi-d1s-t113-mangopi-mq-r.dtsi"
+
+/ {
+	model = "MangoPi MQ-R-T113";
+	compatible = "widora,mangopi-mq-r-t113", "allwinner,sun8i-t113s";
+
+	aliases {
+		ethernet0 = &rtl8189ftv;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&mmc1 {
+	rtl8189ftv: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 = WL_WAKE_AP */
+		interrupt-names = "host-wake";
+	};
+};
diff --git a/arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi b/arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
new file mode 100644
index 0000000000000..e9bc749488bb2
--- /dev/null
+++ b/arch/arm/boot/dts/sunxi-d1s-t113-mangopi-mq-r.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2022 Arm Ltd.
+/*
+ * Common peripherals and configurations for MangoPi MQ-R boards.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
+		};
+	};
+
+	/* board wide 5V supply directly from the USB-C socket */
+	reg_vcc5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board */
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	/* XC6206 LDO on the board */
+	reg_avdd2v8: regulator-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_3v3>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3v3>;
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_3v3>;
+	vcc-pd-supply = <&reg_3v3>;
+	vcc-pe-supply = <&reg_avdd2v8>;
+	vcc-pf-supply = <&reg_3v3>;
+	vcc-pg-supply = <&reg_3v3>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pb_pins>;
+	status = "okay";
+};
+
+/* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};
-- 
2.35.7


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv