From: Conor Dooley <conor@kernel.org>
To: Minda Chen <minda.chen@starfivetech.com>
Cc: Rob Herring <robh+dt@kernel.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-riscv@lists.infradead.org,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>
Subject: Re: [PATCH v2 1/1] riscv: dts: starfive: add PCIe dts configuration for JH7110
Date: Sat, 22 Jun 2024 13:08:11 +0100 [thread overview]
Message-ID: <20240622-festivity-salon-bbad348a12c8@spud> (raw)
In-Reply-To: <20240621082231.92896-2-minda.chen@starfivetech.com>
[-- Attachment #1.1: Type: text/plain, Size: 7579 bytes --]
On Fri, Jun 21, 2024 at 04:22:31PM +0800, Minda Chen wrote:
> Add PCIe dts configuraion for JH7110 SoC platform.
I think the commit message should mention that the star64 doesn't have a
pci port exposed. If nothing else crops up, I'll edit it myself if
that's okay?
Thanks,
Conor.
>
> Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
> Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
> ---
> .../boot/dts/starfive/jh7110-common.dtsi | 62 +++++++++++++
> .../boot/dts/starfive/jh7110-milkv-mars.dts | 7 ++
> .../jh7110-starfive-visionfive-2.dtsi | 8 ++
> arch/riscv/boot/dts/starfive/jh7110.dtsi | 86 +++++++++++++++++++
> 4 files changed, 163 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> index 8ff6ea64f048..f91abc660ae8 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> @@ -294,6 +294,20 @@
> status = "okay";
> };
>
> +&pcie0 {
> + perst-gpios = <&sysgpio 26 GPIO_ACTIVE_LOW>;
> + phys = <&pciephy0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie0_pins>;
> +};
> +
> +&pcie1 {
> + perst-gpios = <&sysgpio 28 GPIO_ACTIVE_LOW>;
> + phys = <&pciephy1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie1_pins>;
> +};
> +
> &pwmdac {
> pinctrl-names = "default";
> pinctrl-0 = <&pwmdac_pins>;
> @@ -476,6 +490,54 @@
> };
> };
>
> + pcie0_pins: pcie0-0 {
> + clkreq-pins {
> + pinmux = <GPIOMUX(27, GPOUT_LOW,
> + GPOEN_DISABLE,
> + GPI_NONE)>;
> + bias-pull-down;
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> +
> + wake-pins {
> + pinmux = <GPIOMUX(32, GPOUT_LOW,
> + GPOEN_DISABLE,
> + GPI_NONE)>;
> + bias-pull-up;
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> + };
> +
> + pcie1_pins: pcie1-0 {
> + clkreq-pins {
> + pinmux = <GPIOMUX(29, GPOUT_LOW,
> + GPOEN_DISABLE,
> + GPI_NONE)>;
> + bias-pull-down;
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> +
> + wake-pins {
> + pinmux = <GPIOMUX(21, GPOUT_LOW,
> + GPOEN_DISABLE,
> + GPI_NONE)>;
> + bias-pull-up;
> + drive-strength = <2>;
> + input-enable;
> + input-schmitt-disable;
> + slew-rate = <0>;
> + };
> + };
> +
> pwmdac_pins: pwmdac-0 {
> pwmdac-pins {
> pinmux = <GPIOMUX(33, GPOUT_SYS_PWMDAC_LEFT,
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
> index fa0eac78e0ba..5cb9e99e1dac 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
> @@ -17,6 +17,13 @@
> assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
> };
>
> +&pcie0 {
> + status = "okay";
> +};
> +
> +&pcie1 {
> + status = "okay";
> +};
>
> &phy0 {
> motorcomm,tx-clk-adj-enabled;
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index 9d70f21c86fc..18f38fc790a4 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -32,3 +32,11 @@
> &mmc0 {
> non-removable;
> };
> +
> +&pcie0 {
> + status = "okay";
> +};
> +
> +&pcie1 {
> + status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 18047195c600..5ac70759e0ab 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -1214,5 +1214,91 @@
> #reset-cells = <1>;
> power-domains = <&pwrc JH7110_PD_VOUT>;
> };
> +
> + pcie0: pcie@940000000 {
> + compatible = "starfive,jh7110-pcie";
> + reg = <0x9 0x40000000 0x0 0x1000000>,
> + <0x0 0x2b000000 0x0 0x100000>;
> + reg-names = "cfg", "apb";
> + linux,pci-domain = <0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + ranges = <0x82000000 0x0 0x30000000 0x0 0x30000000 0x0 0x08000000>,
> + <0xc3000000 0x9 0x00000000 0x9 0x00000000 0x0 0x40000000>;
> + interrupts = <56>;
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc0 0x1>,
> + <0x0 0x0 0x0 0x2 &pcie_intc0 0x2>,
> + <0x0 0x0 0x0 0x3 &pcie_intc0 0x3>,
> + <0x0 0x0 0x0 0x4 &pcie_intc0 0x4>;
> + msi-controller;
> + device_type = "pci";
> + starfive,stg-syscon = <&stg_syscon>;
> + bus-range = <0x0 0xff>;
> + clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_STG_AXI>,
> + <&stgcrg JH7110_STGCLK_PCIE0_TL>,
> + <&stgcrg JH7110_STGCLK_PCIE0_AXI_MST0>,
> + <&stgcrg JH7110_STGCLK_PCIE0_APB>;
> + clock-names = "noc", "tl", "axi_mst0", "apb";
> + resets = <&stgcrg JH7110_STGRST_PCIE0_AXI_MST0>,
> + <&stgcrg JH7110_STGRST_PCIE0_AXI_SLV0>,
> + <&stgcrg JH7110_STGRST_PCIE0_AXI_SLV>,
> + <&stgcrg JH7110_STGRST_PCIE0_BRG>,
> + <&stgcrg JH7110_STGRST_PCIE0_CORE>,
> + <&stgcrg JH7110_STGRST_PCIE0_APB>;
> + reset-names = "mst0", "slv0", "slv", "brg",
> + "core", "apb";
> + status = "disabled";
> +
> + pcie_intc0: interrupt-controller {
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + };
> + };
> +
> + pcie1: pcie@9c0000000 {
> + compatible = "starfive,jh7110-pcie";
> + reg = <0x9 0xc0000000 0x0 0x1000000>,
> + <0x0 0x2c000000 0x0 0x100000>;
> + reg-names = "cfg", "apb";
> + linux,pci-domain = <1>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + ranges = <0x82000000 0x0 0x38000000 0x0 0x38000000 0x0 0x08000000>,
> + <0xc3000000 0x9 0x80000000 0x9 0x80000000 0x0 0x40000000>;
> + interrupts = <57>;
> + interrupt-map-mask = <0x0 0x0 0x0 0x7>;
> + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc1 0x1>,
> + <0x0 0x0 0x0 0x2 &pcie_intc1 0x2>,
> + <0x0 0x0 0x0 0x3 &pcie_intc1 0x3>,
> + <0x0 0x0 0x0 0x4 &pcie_intc1 0x4>;
> + msi-controller;
> + device_type = "pci";
> + starfive,stg-syscon = <&stg_syscon>;
> + bus-range = <0x0 0xff>;
> + clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_STG_AXI>,
> + <&stgcrg JH7110_STGCLK_PCIE1_TL>,
> + <&stgcrg JH7110_STGCLK_PCIE1_AXI_MST0>,
> + <&stgcrg JH7110_STGCLK_PCIE1_APB>;
> + clock-names = "noc", "tl", "axi_mst0", "apb";
> + resets = <&stgcrg JH7110_STGRST_PCIE1_AXI_MST0>,
> + <&stgcrg JH7110_STGRST_PCIE1_AXI_SLV0>,
> + <&stgcrg JH7110_STGRST_PCIE1_AXI_SLV>,
> + <&stgcrg JH7110_STGRST_PCIE1_BRG>,
> + <&stgcrg JH7110_STGRST_PCIE1_CORE>,
> + <&stgcrg JH7110_STGRST_PCIE1_APB>;
> + reset-names = "mst0", "slv0", "slv", "brg",
> + "core", "apb";
> + status = "disabled";
> +
> + pcie_intc1: interrupt-controller {
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + };
> + };
> };
> };
> --
> 2.17.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 161 bytes --]
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2024-06-22 12:08 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-21 8:22 [PATCH v2 0/1] Add PCIe dts configuration for JH7110 Minda Chen
2024-06-21 8:22 ` [PATCH v2 1/1] riscv: dts: starfive: add " Minda Chen
2024-06-22 12:08 ` Conor Dooley [this message]
2024-06-24 1:18 ` Minda Chen
2024-06-24 16:32 ` Conor Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240622-festivity-salon-bbad348a12c8@spud \
--to=conor@kernel.org \
--cc=aou@eecs.berkeley.edu \
--cc=devicetree@vger.kernel.org \
--cc=emil.renner.berthing@canonical.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=minda.chen@starfivetech.com \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox