[PATCH v6 0/5] Add support for NetCube Systems Nagami SoM and its carrier boards

From: Lukas Schmid <lukas.schmid@netcube.li>
To: Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	Samuel Holland <samuel@sholland.org>,
	Paul Walmsley <paul.walmsley@sifive.com>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Albert Ou <aou@eecs.berkeley.edu>,
	Alexandre Ghiti <alex@ghiti.fr>,
	Maxime Ripard <mripard@kernel.org>
Cc: Lukas Schmid <lukas.schmid@netcube.li>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
	linux-riscv@lists.infradead.org
Subject: [PATCH v6 0/5] Add support for NetCube Systems Nagami SoM and its carrier boards
Date: Fri, 29 Aug 2025 14:37:53 +0200	[thread overview]
Message-ID: <20250829123800.1232645-1-lukas.schmid@netcube.li> (raw)

This series adds support for the NetCube Systems Nagami SoM and its
associated carrier boards, the Nagami Basic Carrier and the Nagami Keypad
Carrier.

Changes in v6:
  - Add 'usb0-enable-hog' to the som to enable the USB-OTG port by default
  - Update the keypad carrier dts to match actual board revision

Changes in v5:
  - Re-add the non-removable property to the ESP32 interface
  - Add the mmc-pwrseq node for the ESP32 to initialize the ESP32 correctly
  - Remove the unused ehci0 and ohci0 nodes from the Keypad Carrier since
    USB port is peripheral only

Changes in v4:
  - Disable the default interfaces on the card-edge but keep the pinctrl
    definitions for them
  - Split the pinctrl definitions for the SPI interface into the basic spi 
    pins and the hold/wp pins
  - Move some mmc0 properties to the Basic Carrier dts
  - Remove non-removable property from the ESP32 interface
  - Fix typo in the keypad matrix definition

Changes in v3:
  - Add missing dcxo node to the SoM dtsi
  - Rename the multi-led node
  - Change dr_mode to "peripheral" for the Keypad Carrier

Changes in v2:
 - Squash the binding patches into one patch
 - Fix formatting of the phy node in the SoM dtsi
 - Add description on where the phy is located in the SoM dtsi
 - Fix the phy address in the SoM dtsi
 - Move the carrier bindings into the same description as enums

Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
---
Lukas Schmid (5):
  dt-bindings: arm: sunxi: Add NetCube Systems Nagami SoM and carrier
    board bindings
  riscv: dts: allwinner: d1s-t113: Add pinctrl's required by NetCube
    Systems Nagami SoM
  ARM: dts: sunxi: add support for NetCube Systems Nagami SoM
  ARM: dts: sunxi: add support for NetCube Systems Nagami Basic Carrier
  ARM: dts: sunxi: add support for NetCube Systems Nagami Keypad Carrier

 .../devicetree/bindings/arm/sunxi.yaml        |   8 +
 arch/arm/boot/dts/allwinner/Makefile          |   3 +
 ...n8i-t113s-netcube-nagami-basic-carrier.dts |  67 +++++
 ...8i-t113s-netcube-nagami-keypad-carrier.dts | 156 +++++++++++
 .../allwinner/sun8i-t113s-netcube-nagami.dtsi | 249 ++++++++++++++++++
 .../boot/dts/allwinner/sunxi-d1s-t113.dtsi    |  48 ++++
 6 files changed, 531 insertions(+)
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi

-- 
2.39.5

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv