From: Troy Mitchell <troy.mitchell@linux.spacemit.com>
To: Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>,
Yixun Lan <dlan@kernel.org>
Cc: linux-sound@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-riscv@lists.infradead.org, spacemit@lists.linux.dev,
jinmei.wei@spacemit.com,
Troy Mitchell <troy.mitchell@linux.spacemit.com>
Subject: [PATCH 0/3] ASoC: add shared BCLK rate constraint for cross-DAI coordination
Date: Thu, 30 Apr 2026 15:46:00 +0800 [thread overview]
Message-ID: <20260430-i2s-same-blk-v1-0-3a1f04eb6159@linux.spacemit.com> (raw)
On some SoCs (e.g. SpacemiT K3), multiple I2S controllers share the
same physical BCLK. When one controller is already streaming, the
others must use hw_params that result in the same BCLK rate, otherwise
the shared clock would be reconfigured and corrupt the active stream.
This series adds framework-level support for this constraint:
Patch 1 adds a bclk field and bclk_ratio to struct snd_soc_dai, plus
a helper snd_soc_dai_set_bclk_clk() for platform drivers to declare
their BCLK clock. It also caches the ratio in the existing
snd_soc_dai_set_bclk_ratio() so the framework can use it for TDM
configurations.
Patch 2 adds the constraint logic in soc-pcm.c. During PCM open,
every DAI that has a bclk clock pointer gets a hw_rule registered
unconditionally. The rule callback runs at hw_refine time: it scans
the card for an active peer sharing the same physical BCLK (via
clk_is_match()) that has already completed hw_params, then constrains
the current stream's rate to match the established BCLK rate. The
first DAI to complete hw_params is unconstrained; subsequent DAIs
must match. Two modes are supported:
- Default (I2S): BCLK = rate * channels * sample_bits. The rule
derives the valid rate range from the current channel and
sample_bits intervals.
- Explicit ratio (TDM): if the driver sets dai->bclk_ratio
(e.g. slots * slot_width), the rule computes the single valid
rate as active_bclk_rate / bclk_ratio.
Patch 3 wires up the SpacemiT K1/K3 I2S driver: a single call to
snd_soc_dai_set_bclk_clk(dai, i2s->c_bclk) in the DAI probe. On SoCs
where the BCLK is not shared (c_bclk is NULL from
devm_clk_get_optional_enabled), the rule is a no-op. On K3, multiple
I2S instances share the same c_bclk, and the framework automatically
constrains their rates.
This series was prompted by review feedback on the SpacemiT K3 I2S
series, where a vendor-specific fixed-sample-rate property was rejected
in favor of a generic framework solution:
https://lore.kernel.org/all/afFqgF6ZRwYdfUmL@sirena.co.uk/
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
---
Troy Mitchell (3):
ASoC: soc-dai: add shared BCLK clock for cross-DAI rate constraints
ASoC: soc-pcm: constrain hw_params when DAIs share the same BCLK
ASoC: spacemit: declare shared BCLK for cross-DAI rate constraint
include/sound/soc-dai.h | 7 +++
sound/soc/soc-dai.c | 17 +++++++
sound/soc/soc-pcm.c | 113 ++++++++++++++++++++++++++++++++++++++++++++
sound/soc/spacemit/k1_i2s.c | 2 +
4 files changed, 139 insertions(+)
---
base-commit: db490fe819ac280fe608b23d98c54a5467ef2948
change-id: 20260429-i2s-same-blk-fe102b18c5ac
Best regards,
--
Troy Mitchell <troy.mitchell@linux.spacemit.com>
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
next reply other threads:[~2026-04-30 7:47 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-04-30 7:46 Troy Mitchell [this message]
2026-04-30 7:46 ` [PATCH 1/3] ASoC: soc-dai: add shared BCLK clock for cross-DAI rate constraints Troy Mitchell
2026-04-30 12:01 ` Mark Brown
2026-04-30 7:46 ` [PATCH 2/3] ASoC: soc-pcm: constrain hw_params when DAIs share the same BCLK Troy Mitchell
2026-04-30 12:05 ` Mark Brown
2026-04-30 7:46 ` [PATCH 3/3] ASoC: spacemit: declare shared BCLK for cross-DAI rate constraint Troy Mitchell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260430-i2s-same-blk-v1-0-3a1f04eb6159@linux.spacemit.com \
--to=troy.mitchell@linux.spacemit.com \
--cc=broonie@kernel.org \
--cc=dlan@kernel.org \
--cc=jinmei.wei@spacemit.com \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=linux-sound@vger.kernel.org \
--cc=perex@perex.cz \
--cc=spacemit@lists.linux.dev \
--cc=tiwai@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox