Linux-RISC-V Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Troy Mitchell <troy.mitchell@linux.spacemit.com>
To: Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>,
	 Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>,
	 Yixun Lan <dlan@kernel.org>,
	Jinmei Wei <weijinmei@linux.spacemit.com>,
	 Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	 Conor Dooley <conor+dt@kernel.org>
Cc: linux-sound@vger.kernel.org, linux-riscv@lists.infradead.org,
	 spacemit@lists.linux.dev, linux-kernel@vger.kernel.org,
	 devicetree@vger.kernel.org,
	 Troy Mitchell <troy.mitchell@linux.spacemit.com>
Subject: [PATCH v2 2/2] ASoC: spacemit: add K3 SoC support with additional clocks
Date: Thu, 07 May 2026 15:33:10 +0800	[thread overview]
Message-ID: <20260507-k3-i2s-v2-2-9cdbf95b7533@linux.spacemit.com> (raw)
In-Reply-To: <20260507-k3-i2s-v2-0-9cdbf95b7533@linux.spacemit.com>

Add support for the SpacemiT K3 SoC I2S controller, which shares the
same IP as K1 but requires additional clocks: sysclk_div, c_sysclk,
and c_bclk. These clocks only exist on K3 and are not present on K1.
The sysclk_div clock is present on most K3 I2S controllers except I2S1.
The c_sysclk and c_bclk clocks are shared across multiple I2S
controllers on K3.

Use devm_clk_get_optional_enabled() to acquire these clocks so that
the driver works on both K1 (where they are absent) and K3 without
needing SoC-specific match data. For K3, the sysclk_div rate is set
before sysclk in set_sysclk, and the common clock rates are configured
in hw_params based on the sample rate.

Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
---
 sound/soc/spacemit/k1_i2s.c | 36 +++++++++++++++++++++++++++++++++++-
 1 file changed, 35 insertions(+), 1 deletion(-)

diff --git a/sound/soc/spacemit/k1_i2s.c b/sound/soc/spacemit/k1_i2s.c
index 1cb99f1abc7c..4e655d714623 100644
--- a/sound/soc/spacemit/k1_i2s.c
+++ b/sound/soc/spacemit/k1_i2s.c
@@ -53,6 +53,9 @@ struct spacemit_i2s_dev {
 	struct clk *sysclk;
 	struct clk *bclk;
 	struct clk *sspa_clk;
+	struct clk *sysclk_div;
+	struct clk *c_sysclk;
+	struct clk *c_bclk;
 
 	struct snd_dmaengine_dai_dma_data capture_dma_data;
 	struct snd_dmaengine_dai_dma_data playback_dma_data;
@@ -189,6 +192,14 @@ static int spacemit_i2s_hw_params(struct snd_pcm_substream *substream,
 		    params_rate(params) *
 		    data_bits;
 
+	ret = clk_set_rate(i2s->c_sysclk, bclk_rate * 2);
+	if (ret)
+		return ret;
+
+	ret = clk_set_rate(i2s->c_bclk, bclk_rate);
+	if (ret)
+		return ret;
+
 	ret = clk_set_rate(i2s->bclk, bclk_rate);
 	if (ret)
 		return ret;
@@ -200,10 +211,17 @@ static int spacemit_i2s_set_sysclk(struct snd_soc_dai *cpu_dai, int clk_id,
 				   unsigned int freq, int dir)
 {
 	struct spacemit_i2s_dev *i2s = dev_get_drvdata(cpu_dai->dev);
+	int ret;
 
 	if (freq == 0)
 		return 0;
 
+	if (i2s->sysclk_div) {
+		ret = clk_set_rate(i2s->sysclk_div, freq);
+		if (ret)
+			return ret;
+	}
+
 	return clk_set_rate(i2s->sysclk, freq);
 }
 
@@ -418,6 +436,21 @@ static int spacemit_i2s_probe(struct platform_device *pdev)
 		return dev_err_probe(i2s->dev, PTR_ERR(i2s->sspa_clk),
 				     "failed to enable sspa clock\n");
 
+	i2s->sysclk_div = devm_clk_get_optional_enabled(i2s->dev, "sysclk_div");
+	if (IS_ERR(i2s->sysclk_div))
+		return dev_err_probe(i2s->dev, PTR_ERR(i2s->sysclk_div),
+				     "failed to enable sysclk_div clock\n");
+
+	i2s->c_sysclk = devm_clk_get_optional_enabled(i2s->dev, "c_sysclk");
+	if (IS_ERR(i2s->c_sysclk))
+		return dev_err_probe(i2s->dev, PTR_ERR(i2s->c_sysclk),
+				     "failed to enable c_sysclk clock\n");
+
+	i2s->c_bclk = devm_clk_get_optional_enabled(i2s->dev, "c_bclk");
+	if (IS_ERR(i2s->c_bclk))
+		return dev_err_probe(i2s->dev, PTR_ERR(i2s->c_bclk),
+				     "failed to enable c_bclk clock\n");
+
 	i2s->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
 	if (IS_ERR(i2s->base))
 		return dev_err_probe(i2s->dev, PTR_ERR(i2s->base), "failed to map registers\n");
@@ -444,6 +477,7 @@ static int spacemit_i2s_probe(struct platform_device *pdev)
 
 static const struct of_device_id spacemit_i2s_of_match[] = {
 	{ .compatible = "spacemit,k1-i2s", },
+	{ .compatible = "spacemit,k3-i2s", },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, spacemit_i2s_of_match);
@@ -458,4 +492,4 @@ static struct platform_driver spacemit_i2s_driver = {
 module_platform_driver(spacemit_i2s_driver);
 
 MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("I2S bus driver for SpacemiT K1 SoC");
+MODULE_DESCRIPTION("I2S bus driver for SpacemiT K1/K3 SoC");

-- 
2.54.0


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

      parent reply	other threads:[~2026-05-07  7:34 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-05-07  7:33 [PATCH v2 0/2] ASoC: spacemit: add K3 SoC support Troy Mitchell
2026-05-07  7:33 ` [PATCH v2 1/2] ASoC: dt-bindings: add SpacemiT K3 SoC compatible Troy Mitchell
2026-05-07  7:33 ` Troy Mitchell [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260507-k3-i2s-v2-2-9cdbf95b7533@linux.spacemit.com \
    --to=troy.mitchell@linux.spacemit.com \
    --cc=broonie@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dlan@kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=lgirdwood@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=linux-sound@vger.kernel.org \
    --cc=perex@perex.cz \
    --cc=robh@kernel.org \
    --cc=spacemit@lists.linux.dev \
    --cc=tiwai@suse.com \
    --cc=weijinmei@linux.spacemit.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox