Re: [PATCH v3 2/2] RISC-V: KVM: add KVM_CAP_RISCV_SET_HGATP_MODE

["Radim Krčmář" <radim.krcmar@oss.qualcomm.com>]

2026-01-25T23:04:50+08:00, <fangyu.yu@linux.alibaba.com>:
> From: Fangyu Yu <fangyu.yu@linux.alibaba.com>
>
> This capability allows userspace to explicitly select the HGATP mode
> for the VM. The selected mode must be less than or equal to the max
> HGATP mode supported by the hardware. This capability must be enabled
> before creating any vCPUs, and can only be set once per VM.
>
> Signed-off-by: Fangyu Yu <fangyu.yu@linux.alibaba.com>
> ---
>  Documentation/virt/kvm/api.rst | 18 ++++++++++++++++++
>  arch/riscv/kvm/vm.c            | 26 ++++++++++++++++++++++++--
>  include/uapi/linux/kvm.h       |  1 +
>  3 files changed, 43 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/virt/kvm/api.rst b/Documentation/virt/kvm/api.rst
> @@ -8765,6 +8765,24 @@ helpful if user space wants to emulate instructions which are not
> +7.47 KVM_CAP_RISCV_SET_HGATP_MODE
> +---------------------------------
> +
> +:Architectures: riscv
> +:Type: VM
> +:Parameters: args[0] contains the requested HGATP mode
> +:Returns:
> +  - 0 on success.
> +  - -EINVAL if args[0] is outside the range of HGATP modes supported by the
> +    hardware.
> +  - -EBUSY if vCPUs have already been created for the VM, if the VM has any
> +    non-empty memslots, or if the capability has already been set for the VM.
> +
> +This capability allows userspace to explicitly select the HGATP mode for
> +the VM. The selected mode must be less than or equal to the maximum HGATP
> +mode supported by the hardware.

"The selected mode must be supported by both KVM and hardware."

(The comparison is a technical detail, and incorrect too since the value
 is bouded from the bottom as well.)

>                                  This capability must be enabled before
> +creating any vCPUs, and can only be set once per VM.

                     ^ "or memslots"

> diff --git a/arch/riscv/kvm/vm.c b/arch/riscv/kvm/vm.c
> @@ -202,6 +202,9 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
>  	case KVM_CAP_VM_GPA_BITS:
>  		r = kvm_riscv_gstage_gpa_bits(&kvm->arch);
>  		break;
> +	case KVM_CAP_RISCV_SET_HGATP_MODE:
> +		r = IS_ENABLED(CONFIG_64BIT) ? 1 : 0;

Maybe we can return the currently selected mode for a bit of extra info?
Another nice option would be to return a bitmask of all supported modes.

I think userspace has otherwise no reason to call it, since it's fine to
just try enable and handle the -EINVAL as "don't care".
1 syscall instead of 2.

> @@ -212,12 +215,31 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
>  
>  int kvm_vm_ioctl_enable_cap(struct kvm *kvm, struct kvm_enable_cap *cap)
>  {
> +	case KVM_CAP_RISCV_SET_HGATP_MODE:
> +#ifdef CONFIG_64BIT
> +		if (cap->args[0] < HGATP_MODE_SV39X4 ||
> +		    cap->args[0] > kvm_riscv_gstage_mode(kvm_riscv_gstage_max_pgd_levels))
> +			return -EINVAL;
> +
> +		if (kvm->arch.gstage_mode_user_initialized || kvm->created_vcpus ||
> +		    !kvm_are_all_memslots_empty(kvm))
> +			return -EBUSY;
> +
> +		kvm->arch.gstage_mode_user_initialized = true;

No need to have gstage_mode_user_initialized, since if the user could
have changed it once, there shouldn't be an issue in changing it again.
It's the other protections that must work.

> +		kvm->arch.kvm_riscv_gstage_pgd_levels =
> +				3 + cap->args[0] - HGATP_MODE_SV39X4;
> +		kvm_debug("VM (vmid:%lu) using SV%lluX4 G-stage page table format\n",
> +			  kvm->arch.vmid.vmid,
> +			  39 + (cap->args[0] - HGATP_MODE_SV39X4) * 9);

(I don't think this debug message is going to be useful after a short
 debugging period, and it would clog the log on each VM launch, so I'd
 rather get rid of it.)

Thanks.

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv