public inbox for linux-riscv@lists.infradead.org
 help / color / mirror / Atom feed
From: Lorenzo Pieralisi <lpieralisi@kernel.org>
To: daire.mcnamara@microchip.com
Cc: conor.dooley@microchip.com, robh+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, paul.walmsley@sifive.com,
	palmer@dabbelt.com, aou@eecs.berkeley.edu, kw@linux.com,
	bhelgaas@google.com, linux-riscv@lists.infradead.org,
	devicetree@vger.kernel.org, linux-pci@vger.kernel.org
Subject: Re: [PATCH v3 07/11] PCI: microchip: Gather MSI information from hardware config registers
Date: Thu, 2 Feb 2023 12:45:30 +0100	[thread overview]
Message-ID: <Y9uiWscjKQpD7JvE@lpieralisi> (raw)
In-Reply-To: <20230111125323.1911373-8-daire.mcnamara@microchip.com>

On Wed, Jan 11, 2023 at 12:53:19PM +0000, daire.mcnamara@microchip.com wrote:
> From: Daire McNamara <daire.mcnamara@microchip.com>
> 
> The PCIe Root Complex on PolarFire SoC is configured at bitstream creation
> time using Libero.  Key MSI-related parameters include the number of
> MSIs (1/2/4/8/16/32) and the MSI address. In the device driver, extract
> this information from hw registers at init time, and use it to configure
> MSI system, including configuring MSI capability structure correctly in
> configuration space.

I don't understand whether this is backward compatible with all existing
host controllers in the field. I assume MSI parameters can always been
probed and that has been always the case for all controllers supported
based on this design, please confirm before I proceed with the review.

Thanks,
Lorenzo

> Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
> Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
> ---
>  drivers/pci/controller/pcie-microchip-host.c | 73 +++++++++++---------
>  1 file changed, 40 insertions(+), 33 deletions(-)
> 
> diff --git a/drivers/pci/controller/pcie-microchip-host.c b/drivers/pci/controller/pcie-microchip-host.c
> index 751f0243deb4..9ff0fb04b953 100644
> --- a/drivers/pci/controller/pcie-microchip-host.c
> +++ b/drivers/pci/controller/pcie-microchip-host.c
> @@ -20,8 +20,7 @@
>  #include "../pci.h"
>  
>  /* Number of MSI IRQs */
> -#define MC_NUM_MSI_IRQS				32
> -#define MC_NUM_MSI_IRQS_CODED			5
> +#define MC_MAX_NUM_MSI_IRQS			32
>  
>  /* PCIe Bridge Phy and Controller Phy offsets */
>  #define MC_PCIE1_BRIDGE_ADDR			0x00008000u
> @@ -31,6 +30,11 @@
>  #define MC_PCIE_CTRL_ADDR			(MC_PCIE1_CTRL_ADDR)
>  
>  /* PCIe Bridge Phy Regs */
> +#define PCIE_PCI_IRQ_DW0			0xa8
> +#define  MSIX_CAP_MASK				BIT(31)
> +#define  NUM_MSI_MSGS_MASK			GENMASK(6, 4)
> +#define  NUM_MSI_MSGS_SHIFT			4
> +
>  #define IMASK_LOCAL				0x180
>  #define  DMA_END_ENGINE_0_MASK			0x00000000u
>  #define  DMA_END_ENGINE_0_SHIFT			0
> @@ -79,7 +83,6 @@
>  #define IMASK_HOST				0x188
>  #define ISTATUS_HOST				0x18c
>  #define IMSI_ADDR				0x190
> -#define  MSI_ADDR				0x190
>  #define ISTATUS_MSI				0x194
>  
>  /* PCIe Master table init defines */
> @@ -158,8 +161,6 @@
>  
>  /* PCIe Config space MSI capability structure */
>  #define MC_MSI_CAP_CTRL_OFFSET			0xe0u
> -#define  MC_MSI_MAX_Q_AVAIL			(MC_NUM_MSI_IRQS_CODED << 1)
> -#define  MC_MSI_Q_SIZE				(MC_NUM_MSI_IRQS_CODED << 4)
>  
>  /* Events */
>  #define EVENT_PCIE_L2_EXIT			0
> @@ -259,7 +260,7 @@ struct mc_msi {
>  	struct irq_domain *dev_domain;
>  	u32 num_vectors;
>  	u64 vector_phy;
> -	DECLARE_BITMAP(used, MC_NUM_MSI_IRQS);
> +	DECLARE_BITMAP(used, MC_MAX_NUM_MSI_IRQS);
>  };
>  
>  struct mc_pcie {
> @@ -382,25 +383,29 @@ static struct {
>  
>  static char poss_clks[][5] = { "fic0", "fic1", "fic2", "fic3" };
>  
> -static void mc_pcie_enable_msi(struct mc_pcie *port, void __iomem *base)
> +static void mc_pcie_fixup_ecam(struct mc_pcie *port, void __iomem *ecam)
>  {
>  	struct mc_msi *msi = &port->msi;
> -	u32 cap_offset = MC_MSI_CAP_CTRL_OFFSET;
> -	u16 msg_ctrl = readw_relaxed(base + cap_offset + PCI_MSI_FLAGS);
> -
> -	msg_ctrl |= PCI_MSI_FLAGS_ENABLE;
> -	msg_ctrl &= ~PCI_MSI_FLAGS_QMASK;
> -	msg_ctrl |= MC_MSI_MAX_Q_AVAIL;
> -	msg_ctrl &= ~PCI_MSI_FLAGS_QSIZE;
> -	msg_ctrl |= MC_MSI_Q_SIZE;
> -	msg_ctrl |= PCI_MSI_FLAGS_64BIT;
> -
> -	writew_relaxed(msg_ctrl, base + cap_offset + PCI_MSI_FLAGS);
> -
> +	u16 reg;
> +	u8 queue_size;
> +
> +	/* Fixup MSI enable flag */
> +	reg = readw_relaxed(ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_FLAGS);
> +	reg |= PCI_MSI_FLAGS_ENABLE;
> +	writew_relaxed(reg, ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_FLAGS);
> +
> +	/* Fixup PCI MSI queue flags */
> +	queue_size = reg & PCI_MSI_FLAGS_QMASK;
> +	queue_size >>= 1;
> +	reg &= ~PCI_MSI_FLAGS_QSIZE;
> +	reg |= queue_size << 4;
> +	writew_relaxed(reg, ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_FLAGS);
> +
> +	/* Fixup MSI addr fields */
>  	writel_relaxed(lower_32_bits(msi->vector_phy),
> -		       base + cap_offset + PCI_MSI_ADDRESS_LO);
> +		       ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_ADDRESS_LO);
>  	writel_relaxed(upper_32_bits(msi->vector_phy),
> -		       base + cap_offset + PCI_MSI_ADDRESS_HI);
> +		       ecam + MC_MSI_CAP_CTRL_OFFSET + PCI_MSI_ADDRESS_HI);
>  }
>  
>  static void mc_handle_msi(struct irq_desc *desc)
> @@ -473,10 +478,7 @@ static int mc_irq_msi_domain_alloc(struct irq_domain *domain, unsigned int virq,
>  {
>  	struct mc_pcie *port = domain->host_data;
>  	struct mc_msi *msi = &port->msi;
> -	void __iomem *bridge_base_addr =
> -		port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
>  	unsigned long bit;
> -	u32 val;
>  
>  	mutex_lock(&msi->lock);
>  	bit = find_first_zero_bit(msi->used, msi->num_vectors);
> @@ -490,11 +492,6 @@ static int mc_irq_msi_domain_alloc(struct irq_domain *domain, unsigned int virq,
>  	irq_domain_set_info(domain, virq, bit, &mc_msi_bottom_irq_chip,
>  			    domain->host_data, handle_edge_irq, NULL, NULL);
>  
> -	/* Enable MSI interrupts */
> -	val = readl_relaxed(bridge_base_addr + IMASK_LOCAL);
> -	val |= PM_MSI_INT_MSI_MASK;
> -	writel_relaxed(val, bridge_base_addr + IMASK_LOCAL);
> -
>  	mutex_unlock(&msi->lock);
>  
>  	return 0;
> @@ -1117,6 +1114,7 @@ static int mc_platform_init(struct pci_config_window *cfg)
>  	struct mc_pcie *port;
>  	void __iomem *bridge_base_addr;
>  	int ret;
> +	u32 val;
>  
>  	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
>  	if (!port)
> @@ -1137,11 +1135,20 @@ static int mc_platform_init(struct pci_config_window *cfg)
>  
>  	bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR;
>  
> -	port->msi.vector_phy = MSI_ADDR;
> -	port->msi.num_vectors = MC_NUM_MSI_IRQS;
> +	/* Allow enabling MSI by disabling MSI-X */
> +	val = readl(bridge_base_addr + PCIE_PCI_IRQ_DW0);
> +	val &= ~MSIX_CAP_MASK;
> +	writel(val, bridge_base_addr + PCIE_PCI_IRQ_DW0);
> +
> +	/* Pick num vectors from bitfile programmed onto FPGA fabric */
> +	val = readl(bridge_base_addr + PCIE_PCI_IRQ_DW0);
> +	val &= NUM_MSI_MSGS_MASK;
> +	val >>= NUM_MSI_MSGS_SHIFT;
> +
> +	port->msi.num_vectors = 1 << val;
>  
> -	/* Hardware doesn't setup MSI by default */
> -	mc_pcie_enable_msi(port, cfg->win);
> +	/* Pick vector address from design */
> +	port->msi.vector_phy = readl_relaxed(bridge_base_addr + IMSI_ADDR);
>  
>  	/* Configure Address Translation Table 0 for PCIe config space */
>  	mc_pcie_setup_window(bridge_base_addr, 0, cfg->res.start & 0xffffffff,
> -- 
> 2.25.1
> 
> 
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

  reply	other threads:[~2023-02-02 11:45 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-11 12:53 [PATCH v3 00/11] PCI: microchip: Partition address translations daire.mcnamara
2023-01-11 12:53 ` [PATCH v3 01/11] PCI: microchip: Correct the DED and SEC interrupt bit offsets daire.mcnamara
2023-01-11 12:53 ` [PATCH v3 02/11] PCI: microchip: Remove cast warning for devm_add_action_or_reset() arg daire.mcnamara
2023-01-11 18:18   ` Conor Dooley
2023-01-11 12:53 ` [PATCH v3 03/11] PCI: microchip: enable building this driver as a module daire.mcnamara
2023-01-11 17:25   ` Uwe Kleine-König
2023-01-11 18:20   ` Conor Dooley
2023-01-11 12:53 ` [PATCH v3 04/11] PCI: microchip: Align register, offset, and mask names with hw docs daire.mcnamara
2023-01-11 12:53 ` [PATCH v3 05/11] PCI: microchip: Enable event handlers to access bridge and ctrl ptrs daire.mcnamara
2023-01-11 12:53 ` [PATCH v3 06/11] PCI: microchip: Clean up initialisation of interrupts daire.mcnamara
2023-01-11 12:53 ` [PATCH v3 07/11] PCI: microchip: Gather MSI information from hardware config registers daire.mcnamara
2023-02-02 11:45   ` Lorenzo Pieralisi [this message]
2023-01-11 12:53 ` [PATCH v3 08/11] PCI: microchip: Re-partition code between probe() and init() daire.mcnamara
2023-01-11 12:53 ` [PATCH v3 09/11] PCI: microchip: Partition outbound address translation daire.mcnamara
2023-02-02 11:28   ` Lorenzo Pieralisi
2023-01-11 12:53 ` [PATCH v3 10/11] PCI: microchip: Partition inbound " daire.mcnamara
2023-02-02 11:31   ` Lorenzo Pieralisi
2023-02-02 12:13     ` Robin Murphy
2023-01-11 12:53 ` [PATCH v3 11/11] riscv: dts: microchip: add parent ranges and dma-ranges for IKRD v2022.09 daire.mcnamara
2023-01-20 11:07 ` [PATCH v3 00/11] PCI: microchip: Partition address translations Conor Dooley
2023-01-31 17:03 ` Daire.McNamara
2023-02-02 11:02   ` Lorenzo Pieralisi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=Y9uiWscjKQpD7JvE@lpieralisi \
    --to=lpieralisi@kernel.org \
    --cc=aou@eecs.berkeley.edu \
    --cc=bhelgaas@google.com \
    --cc=conor.dooley@microchip.com \
    --cc=daire.mcnamara@microchip.com \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=kw@linux.com \
    --cc=linux-pci@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=palmer@dabbelt.com \
    --cc=paul.walmsley@sifive.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox