* [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1
@ 2025-07-02 6:01 Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 1/5] dt-bindings: net: Add " Vivian Wang
` (5 more replies)
0 siblings, 6 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 6:01 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Vivian Wang, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel, Conor Dooley
SpacemiT K1 has two gigabit Ethernet MACs with RGMII and RMII support.
Add a driver for them, as well as the supporting devicetree and bindings
updates.
Tested on BananaPi BPI-F3 and Milk-V Jupiter.
I would like to note that even though some bit field names superficially
resemble that of DesignWare MAC, all other differences point to it in
fact being a custom design.
Based on SpacemiT drivers [1].
This series depends on reset controller support [2] and DMA buses [3]
for K1. There are some minor conflicts resulting from both touching
k1.dtsi, but it should just both be adding nodes.
These patches can also be pulled from:
https://github.com/dramforever/linux/tree/k1/ethernet/v3
[1]: https://github.com/spacemit-com/linux-k1x
[2]: https://lore.kernel.org/all/20250613011139.1201702-1-elder@riscstar.com
[3]: https://lore.kernel.org/all/20250623-k1-dma-buses-rfc-wip-v1-0-c0144082061f@iscas.ac.cn
---
Changes in v3:
- Refactored and simplified emac_tx_mem_map
- Addressed other minor v2 review comments
- Removed what was patch 3 in v2, depend on DMA buses instead
- DT nodes in alphabetical order where appropriate
- Link to v2: https://lore.kernel.org/r/20250618-net-k1-emac-v2-0-94f5f07227a8@iscas.ac.cn
Changes in v2:
- dts: Put eth0 and eth1 nodes under a bus with dma-ranges
- dts: Added Milk-V Jupiter
- Fix typo in emac_init_hw() that broke the driver (Oops!)
- Reformatted line lengths to under 80
- Addressed other v1 review comments
- Link to v1: https://lore.kernel.org/r/20250613-net-k1-emac-v1-0-cc6f9e510667@iscas.ac.cn
---
Vivian Wang (5):
dt-bindings: net: Add support for SpacemiT K1
net: spacemit: Add K1 Ethernet MAC
riscv: dts: spacemit: Add Ethernet support for K1
riscv: dts: spacemit: Add Ethernet support for BPI-F3
riscv: dts: spacemit: Add Ethernet support for Jupiter
.../devicetree/bindings/net/spacemit,k1-emac.yaml | 81 +
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 46 +
arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46 +
arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi | 48 +
arch/riscv/boot/dts/spacemit/k1.dtsi | 22 +
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/spacemit/Kconfig | 29 +
drivers/net/ethernet/spacemit/Makefile | 6 +
drivers/net/ethernet/spacemit/k1_emac.c | 1884 ++++++++++++++++++++
drivers/net/ethernet/spacemit/k1_emac.h | 420 +++++
11 files changed, 2584 insertions(+)
---
base-commit: d9946fe286439c2aeaa7953b8c316efe5b83d515
change-id: 20250606-net-k1-emac-3e181508ea64
prerequisite-message-id: <20250613011139.1201702-1-elder@riscstar.com>
prerequisite-patch-id: 2c73c63bef3640e63243ddcf3c07b108d45f6816
prerequisite-patch-id: 0faba75db33c96a588e722c4f2b3862c4cbdaeae
prerequisite-patch-id: 5db8688ef86188ec091145fae9e14b2211cd2b8c
prerequisite-patch-id: e0fe84381637dc888d996a79ea717ff0e3441bd1
prerequisite-patch-id: 2fc0ef1c2fcda92ad83400da5aadaf194fe78627
prerequisite-patch-id: bfa54447803e5642059c386e2bd96297e691d0bf
prerequisite-message-id: <20250523-22-k1-sdhci-v1-1-6e0adddf7494@gentoo.org>
prerequisite-patch-id: 53fc23b06e26ab0ebb2c52ee09f4b2cffab889e2
prerequisite-message-id: <20250623-k1-dma-buses-rfc-wip-v1-0-c0144082061f@iscas.ac.cn>
prerequisite-patch-id: 7f04dcf6f82a9a9fa3a8a78ae4992571f85eb6ca
prerequisite-patch-id: 291c9bcd2ce688e08a8ab57c6d274a57cac6b33c
prerequisite-patch-id: 957d7285e8d2a7698beb0c25cb0f6ea733246af0
Best regards,
--
Vivian "dramforever" Wang
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH net-next v3 1/5] dt-bindings: net: Add support for SpacemiT K1
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
@ 2025-07-02 6:01 ` Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC Vivian Wang
` (4 subsequent siblings)
5 siblings, 0 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 6:01 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Vivian Wang, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel, Conor Dooley
The Ethernet MACs on SpacemiT K1 appears to be a custom design. SpacemiT
refers to them as "EMAC", so let's just call them "spacemit,k1-emac".
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
---
.../devicetree/bindings/net/spacemit,k1-emac.yaml | 81 ++++++++++++++++++++++
1 file changed, 81 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/spacemit,k1-emac.yaml b/Documentation/devicetree/bindings/net/spacemit,k1-emac.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..500a3e1daa230ea3a1fad30d8ea56a7822fccb3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/spacemit,k1-emac.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/spacemit,k1-emac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SpacemiT K1 Ethernet MAC
+
+allOf:
+ - $ref: ethernet-controller.yaml#
+
+maintainers:
+ - Vivian Wang <wangruikang@iscas.ac.cn>
+
+properties:
+ compatible:
+ const: spacemit,k1-emac
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ mdio-bus:
+ $ref: mdio.yaml#
+ unevaluatedProperties: false
+
+ resets:
+ maxItems: 1
+
+ spacemit,apmu:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ - items:
+ - description: phandle to syscon that controls this MAC
+ - description: offset of control registers
+ description:
+ A phandle to syscon with byte offset to control registers for this MAC
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - interrupts
+ - resets
+ - spacemit,apmu
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/spacemit,k1-syscon.h>
+
+ ethernet@cac80000 {
+ compatible = "spacemit,k1-emac";
+ reg = <0xcac80000 0x00000420>;
+ clocks = <&syscon_apmu CLK_EMAC0_BUS>;
+ interrupts = <131>;
+ mac-address = [ 00 00 00 00 00 00 ];
+ phy-handle = <&rgmii0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_cfg>;
+ resets = <&syscon_apmu RESET_EMAC0>;
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <0>;
+ spacemit,apmu = <&syscon_apmu 0x3e4>;
+
+ mdio-bus {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ rgmii0: phy@1 {
+ reg = <0x1>;
+ };
+ };
+ };
--
2.49.0
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 1/5] dt-bindings: net: Add " Vivian Wang
@ 2025-07-02 6:01 ` Vivian Wang
2025-07-02 7:17 ` Maxime Chevallier
2025-07-03 7:19 ` Simon Horman
2025-07-02 6:01 ` [PATCH net-next v3 3/5] riscv: dts: spacemit: Add Ethernet support for K1 Vivian Wang
` (3 subsequent siblings)
5 siblings, 2 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 6:01 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Vivian Wang, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
The Ethernet MACs found on SpacemiT K1 appears to be a custom design
that only superficially resembles some other embedded MACs. SpacemiT
refers to them as "EMAC", so let's just call the driver "k1_emac".
This driver is based on "k1x-emac" in the same directory in the vendor's
tree [1]. Some debugging tunables have been fixed to vendor-recommended
defaults, and PTP support is not included yet.
[1]: https://github.com/spacemit-com/linux-k1x
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
---
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/spacemit/Kconfig | 29 +
drivers/net/ethernet/spacemit/Makefile | 6 +
drivers/net/ethernet/spacemit/k1_emac.c | 1884 +++++++++++++++++++++++++++++++
drivers/net/ethernet/spacemit/k1_emac.h | 420 +++++++
6 files changed, 2341 insertions(+)
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index f86d4557d8d7756a5e27bc17578353b5c19ca108..aead145dd91d129b7bb410f2d4d754c744dddbf4 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -188,6 +188,7 @@ source "drivers/net/ethernet/sis/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
source "drivers/net/ethernet/smsc/Kconfig"
source "drivers/net/ethernet/socionext/Kconfig"
+source "drivers/net/ethernet/spacemit/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
source "drivers/net/ethernet/sunplus/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 67182339469a0d8337cc4e92aa51e498c615156d..998dd628b202ced212748450753fe180f0440c74 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -91,6 +91,7 @@ obj-$(CONFIG_NET_VENDOR_SOLARFLARE) += sfc/
obj-$(CONFIG_NET_VENDOR_SGI) += sgi/
obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
obj-$(CONFIG_NET_VENDOR_SOCIONEXT) += socionext/
+obj-$(CONFIG_NET_VENDOR_SPACEMIT) += spacemit/
obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
obj-$(CONFIG_NET_VENDOR_SUN) += sun/
obj-$(CONFIG_NET_VENDOR_SUNPLUS) += sunplus/
diff --git a/drivers/net/ethernet/spacemit/Kconfig b/drivers/net/ethernet/spacemit/Kconfig
new file mode 100644
index 0000000000000000000000000000000000000000..85ef61a9b4eff4249ad2d32a6e7dbf283b0c180f
--- /dev/null
+++ b/drivers/net/ethernet/spacemit/Kconfig
@@ -0,0 +1,29 @@
+config NET_VENDOR_SPACEMIT
+ bool "SpacemiT devices"
+ default y
+ depends on ARCH_SPACEMIT || COMPILE_TEST
+ help
+ If you have a network (Ethernet) device belonging to this class,
+ say Y.
+
+ Note that the answer to this question does not directly affect
+ the kernel: saying N will just cause the configurator to skip all
+ the questions regarding SpacemiT devices. If you say Y, you will
+ be asked for your specific chipset/driver in the following questions.
+
+if NET_VENDOR_SPACEMIT
+
+config SPACEMIT_K1_EMAC
+ tristate "SpacemiT K1 Ethernet MAC driver"
+ depends on ARCH_SPACEMIT || COMPILE_TEST
+ depends on MFD_SYSCON
+ depends on OF
+ default m if ARCH_SPACEMIT
+ select PHYLIB
+ help
+ This driver supports the Ethernet MAC in the SpacemiT K1 SoC.
+
+ To compile this driver as a module, choose M here: the module
+ will be called k1_emac.
+
+endif # NET_VENDOR_SPACEMIT
diff --git a/drivers/net/ethernet/spacemit/Makefile b/drivers/net/ethernet/spacemit/Makefile
new file mode 100644
index 0000000000000000000000000000000000000000..d29efd997a4ff5dcb50986e439997df7e3650570
--- /dev/null
+++ b/drivers/net/ethernet/spacemit/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the SpacemiT network device drivers.
+#
+
+obj-$(CONFIG_SPACEMIT_K1_EMAC) += k1_emac.o
diff --git a/drivers/net/ethernet/spacemit/k1_emac.c b/drivers/net/ethernet/spacemit/k1_emac.c
new file mode 100644
index 0000000000000000000000000000000000000000..3929355cf81f8a4450ce8f7d748b0ed12b7a08c7
--- /dev/null
+++ b/drivers/net/ethernet/spacemit/k1_emac.c
@@ -0,0 +1,1884 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SpacemiT K1 Ethernet driver
+ *
+ * Copyright (C) 2023-2025 SpacemiT (Hangzhou) Technology Co. Ltd
+ * Copyright (C) 2025 Vivian Wang <wangruikang@iscas.ac.cn>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/rtnetlink.h>
+#include <linux/timer.h>
+#include <linux/types.h>
+
+#include "k1_emac.h"
+
+#define DRIVER_NAME "k1_emac"
+
+#define EMAC_DEFAULT_BUFSIZE 1536
+#define EMAC_RX_BUF_2K 2048
+#define EMAC_RX_BUF_4K 4096
+
+/* Tuning parameters from SpacemiT */
+#define EMAC_TX_FRAMES 64
+#define EMAC_TX_COAL_TIMEOUT 40000
+#define EMAC_RX_FRAMES 64
+#define EMAC_RX_COAL_TIMEOUT (600 * 312)
+
+#define DEFAULT_TX_ALMOST_FULL 0x1f8
+#define DEFAULT_TX_THRESHOLD 1518
+#define DEFAULT_RX_THRESHOLD 12
+#define DEFAULT_TX_RING_NUM 1024
+#define DEFAULT_RX_RING_NUM 1024
+#define DEFAULT_DMA_BURST MREGBIT_BURST_16WORD
+#define HASH_TABLE_SIZE 64
+
+enum rx_frame_status {
+ RX_FRAME_OK,
+ RX_FRAME_DISCARD,
+};
+
+struct desc_buf {
+ u64 dma_addr;
+ void *buff_addr;
+ u16 dma_len;
+ u8 map_as_page;
+};
+
+struct emac_tx_desc_buffer {
+ struct sk_buff *skb;
+ struct desc_buf buf[2];
+};
+
+struct emac_rx_desc_buffer {
+ struct sk_buff *skb;
+ u64 dma_addr;
+ void *buff_addr;
+ u16 dma_len;
+ u8 map_as_page;
+};
+
+/**
+ * struct emac_desc_ring - Software-side information for one descriptor ring
+ * Same struture used for both RX and TX
+ * @desc_addr: Virtual address to the descriptor ring memory
+ * @desc_dma_addr: DMA address of the descriptor ring
+ * @total_size: Size of ring in bytes
+ * @total_cnt: Number of descriptors
+ * @head: Next descriptor to associate a buffer with
+ * @tail: Next descriptor to check status bit
+ * @rx_desc_buf: Array of descriptors for RX
+ * @tx_desc_buf: Array of descriptors for TX, with max of two buffers each
+ */
+struct emac_desc_ring {
+ void *desc_addr;
+ dma_addr_t desc_dma_addr;
+ u32 total_size;
+ u32 total_cnt;
+ u32 head;
+ u32 tail;
+ union {
+ struct emac_rx_desc_buffer *rx_desc_buf;
+ struct emac_tx_desc_buffer *tx_desc_buf;
+ };
+};
+
+struct emac_priv {
+ void __iomem *iobase;
+ u32 dma_buf_sz;
+ struct emac_desc_ring tx_ring;
+ struct emac_desc_ring rx_ring;
+
+ struct net_device *ndev;
+ struct napi_struct napi;
+ struct platform_device *pdev;
+ struct clk *bus_clk;
+ struct clk *ref_clk;
+ struct regmap *regmap_apmu;
+ u32 regmap_apmu_offset;
+ int irq;
+
+ phy_interface_t phy_interface;
+
+ struct emac_hw_stats *hw_stats;
+
+ u32 tx_count_frames;
+ u32 tx_coal_frames;
+ u32 tx_coal_timeout;
+ struct work_struct tx_timeout_task;
+
+ struct timer_list txtimer;
+
+ u32 tx_delay;
+ u32 rx_delay;
+
+ /* Held when reading statistics counters because of indirect access */
+ spinlock_t stats_lock;
+};
+
+static void emac_wr(struct emac_priv *priv, u32 reg, u32 val)
+{
+ writel(val, priv->iobase + reg);
+}
+
+static int emac_rd(struct emac_priv *priv, u32 reg)
+{
+ return readl(priv->iobase + reg);
+}
+
+#define EMAC_ETHTOOL_STAT(x) \
+ { #x, offsetof(struct emac_hw_stats, x) / sizeof(u32) }
+
+static const struct emac_ethtool_stats {
+ char str[ETH_GSTRING_LEN];
+ u32 offset;
+} emac_ethtool_stats[] = {
+ EMAC_ETHTOOL_STAT(tx_ok_pkts),
+ EMAC_ETHTOOL_STAT(tx_total_pkts),
+ EMAC_ETHTOOL_STAT(tx_ok_bytes),
+ EMAC_ETHTOOL_STAT(tx_err_pkts),
+ EMAC_ETHTOOL_STAT(tx_singleclsn_pkts),
+ EMAC_ETHTOOL_STAT(tx_multiclsn_pkts),
+ EMAC_ETHTOOL_STAT(tx_lateclsn_pkts),
+ EMAC_ETHTOOL_STAT(tx_excessclsn_pkts),
+ EMAC_ETHTOOL_STAT(tx_unicast_pkts),
+ EMAC_ETHTOOL_STAT(tx_multicast_pkts),
+ EMAC_ETHTOOL_STAT(tx_broadcast_pkts),
+ EMAC_ETHTOOL_STAT(tx_pause_pkts),
+ EMAC_ETHTOOL_STAT(rx_ok_pkts),
+ EMAC_ETHTOOL_STAT(rx_total_pkts),
+ EMAC_ETHTOOL_STAT(rx_crc_err_pkts),
+ EMAC_ETHTOOL_STAT(rx_align_err_pkts),
+ EMAC_ETHTOOL_STAT(rx_err_total_pkts),
+ EMAC_ETHTOOL_STAT(rx_ok_bytes),
+ EMAC_ETHTOOL_STAT(rx_total_bytes),
+ EMAC_ETHTOOL_STAT(rx_unicast_pkts),
+ EMAC_ETHTOOL_STAT(rx_multicast_pkts),
+ EMAC_ETHTOOL_STAT(rx_broadcast_pkts),
+ EMAC_ETHTOOL_STAT(rx_pause_pkts),
+ EMAC_ETHTOOL_STAT(rx_len_err_pkts),
+ EMAC_ETHTOOL_STAT(rx_len_undersize_pkts),
+ EMAC_ETHTOOL_STAT(rx_len_oversize_pkts),
+ EMAC_ETHTOOL_STAT(rx_len_fragment_pkts),
+ EMAC_ETHTOOL_STAT(rx_len_jabber_pkts),
+ EMAC_ETHTOOL_STAT(rx_64_pkts),
+ EMAC_ETHTOOL_STAT(rx_65_127_pkts),
+ EMAC_ETHTOOL_STAT(rx_128_255_pkts),
+ EMAC_ETHTOOL_STAT(rx_256_511_pkts),
+ EMAC_ETHTOOL_STAT(rx_512_1023_pkts),
+ EMAC_ETHTOOL_STAT(rx_1024_1518_pkts),
+ EMAC_ETHTOOL_STAT(rx_1519_plus_pkts),
+ EMAC_ETHTOOL_STAT(rx_drp_fifo_full_pkts),
+ EMAC_ETHTOOL_STAT(rx_truncate_fifo_full_pkts),
+};
+
+static int emac_phy_interface_config(struct emac_priv *priv)
+{
+ u32 val = 0, mask = PHY_INTF_RGMII;
+
+ switch (priv->phy_interface) {
+ case PHY_INTERFACE_MODE_RMII:
+ mask |= REF_CLK_SEL;
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ val |= PHY_INTF_RGMII;
+
+ mask |= RGMII_TX_CLK_SEL;
+ break;
+ default:
+ netdev_err(priv->ndev, "Unsupported PHY interface %d",
+ priv->phy_interface);
+ return -EINVAL;
+ }
+
+ regmap_update_bits(priv->regmap_apmu,
+ priv->regmap_apmu_offset + APMU_EMAC_CTRL_REG,
+ mask, val);
+
+ return 0;
+}
+
+static int emac_reset_hw(struct emac_priv *priv)
+{
+ /* Disable all interrupts */
+ emac_wr(priv, MAC_INTERRUPT_ENABLE, 0x0);
+ emac_wr(priv, DMA_INTERRUPT_ENABLE, 0x0);
+
+ /* Disable transmit and receive units */
+ emac_wr(priv, MAC_RECEIVE_CONTROL, 0x0);
+ emac_wr(priv, MAC_TRANSMIT_CONTROL, 0x0);
+
+ /* Disable DMA */
+ emac_wr(priv, DMA_CONTROL, 0x0);
+
+ /* Reset MAC and stats */
+ emac_wr(priv, MAC_GLOBAL_CONTROL,
+ MREGBIT_RESET_RX_STAT_COUNTERS |
+ MREGBIT_RESET_TX_STAT_COUNTERS);
+ emac_wr(priv, MAC_GLOBAL_CONTROL, 0x0);
+
+ return 0;
+}
+
+static int emac_init_hw(struct emac_priv *priv)
+{
+ u32 rxirq = 0, dma = 0;
+
+ regmap_set_bits(priv->regmap_apmu,
+ priv->regmap_apmu_offset + APMU_EMAC_CTRL_REG,
+ AXI_SINGLE_ID);
+
+ /* Disable transmit and receive units */
+ emac_wr(priv, MAC_RECEIVE_CONTROL, 0x0);
+ emac_wr(priv, MAC_TRANSMIT_CONTROL, 0x0);
+
+ /* Enable mac address 1 filtering */
+ emac_wr(priv, MAC_ADDRESS_CONTROL, MREGBIT_MAC_ADDRESS1_ENABLE);
+
+ /* Zero initialize the multicast hash table */
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0x0);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0x0);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0x0);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0x0);
+
+ /* Configure Thresholds */
+ emac_wr(priv, MAC_TRANSMIT_FIFO_ALMOST_FULL, DEFAULT_TX_ALMOST_FULL);
+ emac_wr(priv, MAC_TRANSMIT_PACKET_START_THRESHOLD,
+ DEFAULT_TX_THRESHOLD);
+ emac_wr(priv, MAC_RECEIVE_PACKET_START_THRESHOLD, DEFAULT_RX_THRESHOLD);
+
+ /* RX IRQ mitigation */
+ rxirq = EMAC_RX_FRAMES & MREGBIT_RECEIVE_IRQ_FRAME_COUNTER_MASK;
+ rxirq |= (EMAC_RX_COAL_TIMEOUT
+ << MREGBIT_RECEIVE_IRQ_TIMEOUT_COUNTER_SHIFT) &
+ MREGBIT_RECEIVE_IRQ_TIMEOUT_COUNTER_MASK;
+
+ rxirq |= MREGBIT_RECEIVE_IRQ_MITIGATION_ENABLE;
+ emac_wr(priv, DMA_RECEIVE_IRQ_MITIGATION_CTRL, rxirq);
+
+ /* Disable and reset DMA */
+ emac_wr(priv, DMA_CONTROL, 0x0);
+
+ emac_wr(priv, DMA_CONFIGURATION, MREGBIT_SOFTWARE_RESET);
+ usleep_range(9000, 10000);
+ emac_wr(priv, DMA_CONFIGURATION, 0x0);
+ usleep_range(9000, 10000);
+
+ dma |= MREGBIT_STRICT_BURST;
+ dma |= MREGBIT_DMA_64BIT_MODE;
+ dma |= DEFAULT_DMA_BURST;
+
+ emac_wr(priv, DMA_CONFIGURATION, dma);
+
+ return 0;
+}
+
+static void emac_set_mac_addr(struct emac_priv *priv, const unsigned char *addr)
+{
+ emac_wr(priv, MAC_ADDRESS1_HIGH, ((addr[1] << 8) | addr[0]));
+ emac_wr(priv, MAC_ADDRESS1_MED, ((addr[3] << 8) | addr[2]));
+ emac_wr(priv, MAC_ADDRESS1_LOW, ((addr[5] << 8) | addr[4]));
+}
+
+static void emac_dma_start_transmit(struct emac_priv *priv)
+{
+ emac_wr(priv, DMA_TRANSMIT_POLL_DEMAND, 0xFF);
+}
+
+static void emac_enable_interrupt(struct emac_priv *priv)
+{
+ u32 val;
+
+ val = emac_rd(priv, DMA_INTERRUPT_ENABLE);
+ val |= MREGBIT_TRANSMIT_TRANSFER_DONE_INTR_ENABLE;
+ val |= MREGBIT_RECEIVE_TRANSFER_DONE_INTR_ENABLE;
+ emac_wr(priv, DMA_INTERRUPT_ENABLE, val);
+}
+
+static void emac_disable_interrupt(struct emac_priv *priv)
+{
+ u32 val;
+
+ val = emac_rd(priv, DMA_INTERRUPT_ENABLE);
+ val &= ~MREGBIT_TRANSMIT_TRANSFER_DONE_INTR_ENABLE;
+ val &= ~MREGBIT_RECEIVE_TRANSFER_DONE_INTR_ENABLE;
+ emac_wr(priv, DMA_INTERRUPT_ENABLE, val);
+}
+
+static u32 emac_tx_avail(struct emac_priv *priv)
+{
+ struct emac_desc_ring *tx_ring = &priv->tx_ring;
+ u32 avail;
+
+ if (tx_ring->tail > tx_ring->head)
+ avail = tx_ring->tail - tx_ring->head - 1;
+ else
+ avail = tx_ring->total_cnt - tx_ring->head + tx_ring->tail - 1;
+
+ return avail;
+}
+
+static void emac_tx_coal_timer_resched(struct emac_priv *priv)
+{
+ mod_timer(&priv->txtimer,
+ jiffies + usecs_to_jiffies(priv->tx_coal_timeout));
+}
+
+static void emac_tx_coal_timer(struct timer_list *t)
+{
+ struct emac_priv *priv = timer_container_of(priv, t, txtimer);
+
+ napi_schedule(&priv->napi);
+}
+
+static bool emac_tx_should_interrupt(struct emac_priv *priv, u32 pkt_num)
+{
+ bool should_interrupt;
+
+ /* Manage TX mitigation */
+ priv->tx_count_frames += pkt_num;
+ if (likely(priv->tx_coal_frames > priv->tx_count_frames)) {
+ emac_tx_coal_timer_resched(priv);
+ should_interrupt = false;
+ } else {
+ priv->tx_count_frames = 0;
+ should_interrupt = true;
+ }
+
+ return should_interrupt;
+}
+
+static void emac_free_tx_buf(struct emac_priv *priv, int i)
+{
+ struct emac_tx_desc_buffer *tx_buf;
+ struct emac_desc_ring *tx_ring;
+ struct desc_buf *buf;
+ int j;
+
+ tx_ring = &priv->tx_ring;
+ tx_buf = &tx_ring->tx_desc_buf[i];
+
+ for (j = 0; j < 2; j++) {
+ buf = &tx_buf->buf[j];
+ if (buf->dma_addr) {
+ if (buf->map_as_page)
+ dma_unmap_page(&priv->pdev->dev, buf->dma_addr,
+ buf->dma_len, DMA_TO_DEVICE);
+ else
+ dma_unmap_single(&priv->pdev->dev,
+ buf->dma_addr, buf->dma_len,
+ DMA_TO_DEVICE);
+
+ buf->dma_addr = 0;
+ buf->map_as_page = false;
+ buf->buff_addr = NULL;
+ }
+ }
+
+ if (tx_buf->skb) {
+ dev_kfree_skb_any(tx_buf->skb);
+ tx_buf->skb = NULL;
+ }
+}
+
+static void emac_clean_tx_desc_ring(struct emac_priv *priv)
+{
+ struct emac_desc_ring *tx_ring = &priv->tx_ring;
+ u32 i;
+
+ /* Free all the TX ring skbs */
+ for (i = 0; i < tx_ring->total_cnt; i++)
+ emac_free_tx_buf(priv, i);
+
+ tx_ring->head = 0;
+ tx_ring->tail = 0;
+}
+
+static void emac_clean_rx_desc_ring(struct emac_priv *priv)
+{
+ struct emac_rx_desc_buffer *rx_buf;
+ struct emac_desc_ring *rx_ring;
+ u32 i;
+
+ rx_ring = &priv->rx_ring;
+
+ /* Free all the RX ring skbs */
+ for (i = 0; i < rx_ring->total_cnt; i++) {
+ rx_buf = &rx_ring->rx_desc_buf[i];
+ if (rx_buf->skb) {
+ dma_unmap_single(&priv->pdev->dev, rx_buf->dma_addr,
+ rx_buf->dma_len, DMA_FROM_DEVICE);
+
+ dev_kfree_skb(rx_buf->skb);
+ rx_buf->skb = NULL;
+ }
+ }
+
+ rx_ring->tail = 0;
+ rx_ring->head = 0;
+}
+
+static int emac_alloc_tx_resources(struct emac_priv *priv)
+{
+ struct emac_desc_ring *tx_ring = &priv->tx_ring;
+ struct platform_device *pdev = priv->pdev;
+ u32 size;
+
+ size = sizeof(struct emac_tx_desc_buffer) * tx_ring->total_cnt;
+
+ tx_ring->tx_desc_buf = kzalloc(size, GFP_KERNEL);
+ if (!tx_ring->tx_desc_buf)
+ return -ENOMEM;
+
+ tx_ring->total_size = tx_ring->total_cnt * sizeof(struct emac_desc);
+ tx_ring->total_size = ALIGN(tx_ring->total_size, PAGE_SIZE);
+
+ tx_ring->desc_addr = dma_alloc_coherent(&pdev->dev, tx_ring->total_size,
+ &tx_ring->desc_dma_addr,
+ GFP_KERNEL);
+ if (!tx_ring->desc_addr) {
+ kfree(tx_ring->tx_desc_buf);
+ return -ENOMEM;
+ }
+
+ tx_ring->head = 0;
+ tx_ring->tail = 0;
+
+ return 0;
+}
+
+static int emac_alloc_rx_resources(struct emac_priv *priv)
+{
+ struct emac_desc_ring *rx_ring = &priv->rx_ring;
+ struct platform_device *pdev = priv->pdev;
+ u32 buf_len;
+
+ buf_len = sizeof(struct emac_rx_desc_buffer) * rx_ring->total_cnt;
+
+ rx_ring->rx_desc_buf = kzalloc(buf_len, GFP_KERNEL);
+ if (!rx_ring->rx_desc_buf)
+ return -ENOMEM;
+
+ rx_ring->total_size = rx_ring->total_cnt * sizeof(struct emac_desc);
+
+ rx_ring->total_size = ALIGN(rx_ring->total_size, PAGE_SIZE);
+
+ rx_ring->desc_addr = dma_alloc_coherent(&pdev->dev, rx_ring->total_size,
+ &rx_ring->desc_dma_addr,
+ GFP_KERNEL);
+ if (!rx_ring->desc_addr) {
+ kfree(rx_ring->rx_desc_buf);
+ return -ENOMEM;
+ }
+
+ rx_ring->head = 0;
+ rx_ring->tail = 0;
+
+ return 0;
+}
+
+static void emac_free_tx_resources(struct emac_priv *priv)
+{
+ struct emac_desc_ring *tr = &priv->tx_ring;
+ struct device *dev = &priv->pdev->dev;
+
+ emac_clean_tx_desc_ring(priv);
+
+ kfree(tr->tx_desc_buf);
+ tr->tx_desc_buf = NULL;
+
+ dma_free_coherent(dev, tr->total_size, tr->desc_addr,
+ tr->desc_dma_addr);
+ tr->desc_addr = NULL;
+}
+
+static void emac_free_rx_resources(struct emac_priv *priv)
+{
+ struct emac_desc_ring *rr = &priv->rx_ring;
+ struct device *dev = &priv->pdev->dev;
+
+ emac_clean_rx_desc_ring(priv);
+
+ kfree(rr->rx_desc_buf);
+ rr->rx_desc_buf = NULL;
+
+ dma_free_coherent(dev, rr->total_size, rr->desc_addr,
+ rr->desc_dma_addr);
+ rr->desc_addr = NULL;
+}
+
+static int emac_tx_clean_desc(struct emac_priv *priv)
+{
+ struct net_device *ndev = priv->ndev;
+ struct emac_desc_ring *tx_ring;
+ struct emac_desc *tx_desc;
+ u32 i;
+
+ netif_tx_lock(ndev);
+
+ tx_ring = &priv->tx_ring;
+
+ i = tx_ring->tail;
+
+ while (i != tx_ring->head) {
+ tx_desc = &((struct emac_desc *)tx_ring->desc_addr)[i];
+
+ /* Stop checking if desc still own by DMA */
+ if (READ_ONCE(tx_desc->desc0) & TX_DESC_0_OWN)
+ break;
+
+ emac_free_tx_buf(priv, i);
+ memset(tx_desc, 0, sizeof(struct emac_desc));
+
+ if (++i == tx_ring->total_cnt)
+ i = 0;
+ }
+
+ tx_ring->tail = i;
+
+ if (unlikely(netif_queue_stopped(ndev) &&
+ emac_tx_avail(priv) > tx_ring->total_cnt / 4))
+ netif_wake_queue(ndev);
+
+ netif_tx_unlock(ndev);
+
+ return 0;
+}
+
+static u32 rx_frame_len(struct emac_desc *desc)
+{
+ return (desc->desc0 & RX_DESC_0_FRAME_PACKET_LENGTH_MASK) >>
+ RX_DESC_0_FRAME_PACKET_LENGTH_SHIFT;
+}
+
+static int emac_rx_frame_status(struct emac_priv *priv, struct emac_desc *desc)
+{
+ /* Drop if not last descriptor */
+ if (!(desc->desc0 & RX_DESC_0_LAST_DESCRIPTOR)) {
+ netdev_dbg(priv->ndev, "RX not last descriptor\n");
+ return RX_FRAME_DISCARD;
+ }
+
+ if (desc->desc0 & RX_DESC_0_FRAME_RUNT) {
+ netdev_dbg(priv->ndev, "RX runt frame\n");
+ return RX_FRAME_DISCARD;
+ }
+
+ if (desc->desc0 & RX_DESC_0_FRAME_CRC_ERR) {
+ netdev_dbg(priv->ndev, "RX frame CRC error\n");
+ return RX_FRAME_DISCARD;
+ }
+
+ if (desc->desc0 & RX_DESC_0_FRAME_MAX_LEN_ERR) {
+ netdev_dbg(priv->ndev, "RX frame exceeds max length\n");
+ return RX_FRAME_DISCARD;
+ }
+
+ if (desc->desc0 & RX_DESC_0_FRAME_JABBER_ERR) {
+ netdev_dbg(priv->ndev, "RX frame jabber error\n");
+ return RX_FRAME_DISCARD;
+ }
+
+ if (desc->desc0 & RX_DESC_0_FRAME_LENGTH_ERR) {
+ netdev_dbg(priv->ndev, "RX frame length error\n");
+ return RX_FRAME_DISCARD;
+ }
+
+ if (rx_frame_len(desc) <= ETH_FCS_LEN ||
+ rx_frame_len(desc) > priv->dma_buf_sz) {
+ netdev_dbg(priv->ndev, "RX frame length unacceptable\n");
+ return RX_FRAME_DISCARD;
+ }
+ return RX_FRAME_OK;
+}
+
+/* RX and TX use the same layout for {RX,TX}_DESC_1_BUFFER_SIZE_{1,2} */
+
+static u32 make_buf_size_1(u32 size)
+{
+ return (size << TX_DESC_1_BUFFER_SIZE_1_SHIFT) &
+ TX_DESC_1_BUFFER_SIZE_1_MASK;
+}
+
+static u32 make_buf_size_2(u32 size)
+{
+ return (size << TX_DESC_1_BUFFER_SIZE_2_SHIFT) &
+ TX_DESC_1_BUFFER_SIZE_2_MASK;
+}
+
+static void emac_alloc_rx_desc_buffers(struct emac_priv *priv)
+{
+ struct emac_desc_ring *rx_ring = &priv->rx_ring;
+ struct emac_desc rx_desc, *rx_desc_addr;
+ struct net_device *ndev = priv->ndev;
+ struct emac_rx_desc_buffer *rx_buf;
+ struct sk_buff *skb;
+ u32 i;
+
+ i = rx_ring->head;
+ rx_buf = &rx_ring->rx_desc_buf[i];
+
+ while (!rx_buf->skb) {
+ skb = netdev_alloc_skb_ip_align(ndev, priv->dma_buf_sz);
+ if (!skb)
+ break;
+
+ skb->dev = ndev;
+
+ rx_buf->skb = skb;
+ rx_buf->dma_len = priv->dma_buf_sz;
+ rx_buf->dma_addr = dma_map_single(&priv->pdev->dev, skb->data,
+ priv->dma_buf_sz,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(&priv->pdev->dev, rx_buf->dma_addr)) {
+ netdev_err(ndev, "dma_mapping_error\n");
+ goto dma_map_err;
+ }
+
+ rx_desc_addr = &((struct emac_desc *)rx_ring->desc_addr)[i];
+
+ memset(&rx_desc, 0, sizeof(rx_desc));
+
+ rx_desc.buffer_addr_1 = rx_buf->dma_addr;
+ rx_desc.desc1 = make_buf_size_1(rx_buf->dma_len);
+
+ if (++i == rx_ring->total_cnt) {
+ rx_desc.desc1 |= RX_DESC_1_END_RING;
+ i = 0;
+ }
+
+ *rx_desc_addr = rx_desc;
+ dma_wmb();
+ WRITE_ONCE(rx_desc_addr->desc0, rx_desc.desc0 | RX_DESC_0_OWN);
+
+ rx_buf = &rx_ring->rx_desc_buf[i];
+ }
+
+ rx_ring->head = i;
+ return;
+
+dma_map_err:
+ dev_kfree_skb_any(skb);
+ rx_buf->skb = NULL;
+}
+
+/* Returns number of packets received */
+static int emac_rx_clean_desc(struct emac_priv *priv, int budget)
+{
+ struct net_device *ndev = priv->ndev;
+ struct emac_rx_desc_buffer *rx_buf;
+ struct emac_desc_ring *rx_ring;
+ struct sk_buff *skb = NULL;
+ struct emac_desc *rx_desc;
+ u32 got = 0, skb_len, i;
+ int status;
+
+ rx_ring = &priv->rx_ring;
+
+ i = rx_ring->tail;
+
+ while (budget--) {
+ rx_desc = &((struct emac_desc *)rx_ring->desc_addr)[i];
+
+ /* Stop checking if rx_desc still owned by DMA */
+ if (READ_ONCE(rx_desc->desc0) & RX_DESC_0_OWN)
+ break;
+
+ dma_rmb();
+
+ rx_buf = &rx_ring->rx_desc_buf[i];
+
+ if (!rx_buf->skb)
+ break;
+
+ got++;
+
+ dma_unmap_single(&priv->pdev->dev, rx_buf->dma_addr,
+ rx_buf->dma_len, DMA_FROM_DEVICE);
+
+ status = emac_rx_frame_status(priv, rx_desc);
+ if (unlikely(status == RX_FRAME_DISCARD)) {
+ ndev->stats.rx_dropped++;
+ dev_kfree_skb_irq(rx_buf->skb);
+ rx_buf->skb = NULL;
+ } else {
+ skb = rx_buf->skb;
+ skb_len = rx_frame_len(rx_desc) - ETH_FCS_LEN;
+ skb_put(skb, skb_len);
+ skb->dev = ndev;
+ ndev->hard_header_len = ETH_HLEN;
+
+ skb->protocol = eth_type_trans(skb, ndev);
+
+ skb->ip_summed = CHECKSUM_NONE;
+
+ napi_gro_receive(&priv->napi, skb);
+
+ ndev->stats.rx_packets++;
+ ndev->stats.rx_bytes += skb_len;
+
+ memset(rx_desc, 0, sizeof(struct emac_desc));
+ rx_buf->skb = NULL;
+ }
+
+ if (++i == rx_ring->total_cnt)
+ i = 0;
+ }
+
+ rx_ring->tail = i;
+
+ emac_alloc_rx_desc_buffers(priv);
+
+ return got;
+}
+
+static int emac_rx_poll(struct napi_struct *napi, int budget)
+{
+ struct emac_priv *priv = container_of(napi, struct emac_priv, napi);
+ int work_done;
+
+ emac_tx_clean_desc(priv);
+
+ work_done = emac_rx_clean_desc(priv, budget);
+ if (work_done < budget && napi_complete_done(napi, work_done))
+ emac_enable_interrupt(priv);
+
+ return work_done;
+}
+
+/*
+ * For convenience, skb->data is fragment 0, frags[0] is fragment 1, etc.
+ *
+ * Each descriptor can hold up to two fragments, called buffer 1 and 2. For each
+ * fragment f, if f % 2 == 0, it uses buffer 1, otherwise it uses buffer 2.
+ */
+
+static int emac_tx_map_frag(struct device *dev, struct emac_desc *tx_desc,
+ struct emac_tx_desc_buffer *tx_buf,
+ struct sk_buff *skb, u32 frag_idx)
+{
+ bool map_as_page, buf_idx;
+ const skb_frag_t *frag;
+ phys_addr_t addr;
+ u32 len;
+ int ret;
+
+ buf_idx = frag_idx % 2;
+
+ if (frag_idx == 0) {
+ /* Non-fragmented part */
+ len = skb_headlen(skb);
+ addr = dma_map_single(dev, skb->data, len, DMA_TO_DEVICE);
+ map_as_page = false;
+ } else {
+ /* Fragment */
+ frag = &skb_shinfo(skb)->frags[frag_idx - 1];
+ len = skb_frag_size(frag);
+ addr = skb_frag_dma_map(dev, frag, 0, len, DMA_TO_DEVICE);
+ map_as_page = true;
+ }
+
+ ret = dma_mapping_error(dev, addr);
+ if (ret)
+ return ret;
+
+ tx_buf->buf[buf_idx].dma_addr = addr;
+ tx_buf->buf[buf_idx].dma_len = len;
+ tx_buf->buf[buf_idx].map_as_page = map_as_page;
+
+ if (buf_idx == 0) {
+ tx_desc->buffer_addr_1 = addr;
+ tx_desc->desc1 |= make_buf_size_1(len);
+ } else {
+ tx_desc->buffer_addr_2 = addr;
+ tx_desc->desc1 |= make_buf_size_2(len);
+ }
+
+ return 0;
+}
+
+static void emac_tx_mem_map(struct emac_priv *priv, struct sk_buff *skb)
+{
+ struct emac_desc_ring *tx_ring = &priv->tx_ring;
+ struct emac_desc tx_desc, *tx_desc_addr;
+ struct device *dev = &priv->pdev->dev;
+ struct emac_tx_desc_buffer *tx_buf;
+ u32 head, old_head, frag_num, f;
+ bool buf_idx;
+
+ frag_num = skb_shinfo(skb)->nr_frags;
+ head = tx_ring->head;
+ old_head = head;
+
+ for (f = 0; f < frag_num + 1; f++) {
+ buf_idx = f % 2;
+
+ /*
+ * If using buffer 1, initialize a new desc. Otherwise, use
+ * buffer 2 of previous fragment's desc.
+ */
+ if (!buf_idx) {
+ tx_buf = &tx_ring->tx_desc_buf[head];
+ tx_desc_addr =
+ &((struct emac_desc *)tx_ring->desc_addr)[head];
+ memset(&tx_desc, 0, sizeof(tx_desc));
+
+ /*
+ * Give ownership for all but first desc initially. For
+ * first desc, give at the end so DMA cannot start
+ * reading uninitialized descs.
+ */
+ if (head != old_head)
+ tx_desc.desc0 |= TX_DESC_0_OWN;
+
+ if (++head == tx_ring->total_cnt) {
+ /* Just used last desc in ring */
+ tx_desc.desc1 |= TX_DESC_1_END_RING;
+ head = 0;
+ }
+ }
+
+ if (emac_tx_map_frag(dev, &tx_desc, tx_buf, skb, f)) {
+ netdev_err(priv->ndev, "Map TX frag %d failed", f);
+ goto dma_map_err;
+ }
+
+ if (f == 0)
+ tx_desc.desc1 |= TX_DESC_1_FIRST_SEGMENT;
+
+ if (f == frag_num) {
+ tx_desc.desc1 |= TX_DESC_1_LAST_SEGMENT;
+ tx_buf->skb = skb;
+ if (emac_tx_should_interrupt(priv, frag_num + 1))
+ tx_desc.desc1 |=
+ TX_DESC_1_INTERRUPT_ON_COMPLETION;
+ }
+
+ *tx_desc_addr = tx_desc;
+ }
+
+ /* All descriptors are ready, give ownership for first desc */
+ tx_desc_addr = &((struct emac_desc *)tx_ring->desc_addr)[old_head];
+ dma_wmb();
+ WRITE_ONCE(tx_desc_addr->desc0, tx_desc_addr->desc0 | TX_DESC_0_OWN);
+
+ emac_dma_start_transmit(priv);
+
+ tx_ring->head = head;
+
+ return;
+
+dma_map_err:
+ dev_kfree_skb_any(skb);
+ priv->ndev->stats.tx_dropped++;
+}
+
+static int emac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+ int nfrags = skb_shinfo(skb)->nr_frags;
+ struct device *dev = &priv->pdev->dev;
+
+ if (unlikely(emac_tx_avail(priv) < nfrags + 1)) {
+ if (!netif_queue_stopped(ndev)) {
+ netif_stop_queue(ndev);
+ dev_err_ratelimited(dev, "TX ring full, stop TX queue\n");
+ }
+ return NETDEV_TX_BUSY;
+ }
+
+ emac_tx_mem_map(priv, skb);
+
+ ndev->stats.tx_packets++;
+ ndev->stats.tx_bytes += skb->len;
+
+ /* Make sure there is space in the ring for the next TX. */
+ if (unlikely(emac_tx_avail(priv) <= MAX_SKB_FRAGS + 2))
+ netif_stop_queue(ndev);
+
+ return NETDEV_TX_OK;
+}
+
+static u32 emac_tx_read_stat_cnt(struct emac_priv *priv, u8 cnt)
+{
+ u32 val, tmp;
+ int ret;
+
+ val = 0x8000 | cnt;
+ emac_wr(priv, MAC_TX_STATCTR_CONTROL, val);
+ val = emac_rd(priv, MAC_TX_STATCTR_CONTROL);
+
+ ret = readl_poll_timeout_atomic(priv->iobase + MAC_TX_STATCTR_CONTROL,
+ val, !(val & 0x8000), 100, 10000);
+
+ if (ret) {
+ netdev_err(priv->ndev, "read TX stat timeout\n");
+ return ret;
+ }
+
+ tmp = emac_rd(priv, MAC_TX_STATCTR_DATA_HIGH);
+ val = tmp << 16;
+ tmp = emac_rd(priv, MAC_TX_STATCTR_DATA_LOW);
+ val |= tmp;
+
+ return val;
+}
+
+static u32 emac_rx_read_stat_cnt(struct emac_priv *priv, u8 cnt)
+{
+ u32 val, tmp;
+ int ret;
+
+ val = 0x8000 | cnt;
+ emac_wr(priv, MAC_RX_STATCTR_CONTROL, val);
+ val = emac_rd(priv, MAC_RX_STATCTR_CONTROL);
+
+ ret = readl_poll_timeout_atomic(priv->iobase + MAC_RX_STATCTR_CONTROL,
+ val, !(val & 0x8000), 100, 10000);
+
+ if (ret) {
+ netdev_err(priv->ndev, "read RX stat timeout\n");
+ return ret;
+ }
+
+ tmp = emac_rd(priv, MAC_RX_STATCTR_DATA_HIGH);
+ val = tmp << 16;
+ tmp = emac_rd(priv, MAC_RX_STATCTR_DATA_LOW);
+ val |= tmp;
+
+ return val;
+}
+
+static int emac_set_mac_address(struct net_device *ndev, void *addr)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+ int ret = eth_mac_addr(ndev, addr);
+
+ if (ret)
+ return ret;
+
+ /* If running, set now; if not running it will be set in emac_up. */
+ if (netif_running(ndev))
+ emac_set_mac_addr(priv, ndev->dev_addr);
+
+ return 0;
+}
+
+static void emac_mac_multicast_filter_clear(struct emac_priv *priv)
+{
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0x0);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0x0);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0x0);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0x0);
+}
+
+/* Configure Multicast and Promiscuous modes */
+static void emac_rx_mode_set(struct net_device *ndev)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+ u32 crc32, bit, reg, hash, val;
+ struct netdev_hw_addr *ha;
+ u32 mc_filter[4] = { 0 };
+
+ val = emac_rd(priv, MAC_ADDRESS_CONTROL);
+
+ val &= ~MREGBIT_PROMISCUOUS_MODE;
+
+ if (ndev->flags & IFF_PROMISC) {
+ /* Enable promisc mode */
+ val |= MREGBIT_PROMISCUOUS_MODE;
+ } else if ((ndev->flags & IFF_ALLMULTI) ||
+ (netdev_mc_count(ndev) > HASH_TABLE_SIZE)) {
+ /* Accept all multicast frames by setting every bit */
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0xffff);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0xffff);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0xffff);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0xffff);
+ } else if (!netdev_mc_empty(ndev)) {
+ emac_mac_multicast_filter_clear(priv);
+ netdev_for_each_mc_addr(ha, ndev) {
+ /* Calculate the CRC of the MAC address */
+ crc32 = ether_crc(ETH_ALEN, ha->addr);
+
+ /*
+ * The hash table is an array of 4 16-bit registers. It
+ * is treated like an array of 64 bits (bits[hash]). Use
+ * the upper 6 bits of the above CRC as the hash value.
+ */
+ hash = (crc32 >> 26) & 0x3F;
+ reg = hash / 16;
+ bit = hash % 16;
+ mc_filter[reg] |= BIT(bit);
+ }
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, mc_filter[0]);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, mc_filter[1]);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, mc_filter[2]);
+ emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, mc_filter[3]);
+ }
+
+ emac_wr(priv, MAC_ADDRESS_CONTROL, val);
+}
+
+static int emac_change_mtu(struct net_device *ndev, int mtu)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+ u32 frame_len;
+
+ if (netif_running(ndev)) {
+ netdev_err(ndev, "must be stopped to change MTU\n");
+ return -EBUSY;
+ }
+
+ frame_len = mtu + ETH_HLEN + ETH_FCS_LEN;
+
+ if (frame_len <= EMAC_DEFAULT_BUFSIZE)
+ priv->dma_buf_sz = EMAC_DEFAULT_BUFSIZE;
+ else if (frame_len <= EMAC_RX_BUF_2K)
+ priv->dma_buf_sz = EMAC_RX_BUF_2K;
+ else
+ priv->dma_buf_sz = EMAC_RX_BUF_4K;
+
+ ndev->mtu = mtu;
+
+ return 0;
+}
+
+static void emac_tx_timeout(struct net_device *ndev, unsigned int txqueue)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+
+ schedule_work(&priv->tx_timeout_task);
+}
+
+static int emac_mii_read(struct mii_bus *bus, int phy_addr, int regnum)
+{
+ struct emac_priv *priv = bus->priv;
+ u32 cmd = 0, val;
+ int ret;
+
+ cmd |= phy_addr & 0x1F;
+ cmd |= (regnum & 0x1F) << 5;
+ cmd |= MREGBIT_START_MDIO_TRANS | MREGBIT_MDIO_READ_WRITE;
+
+ emac_wr(priv, MAC_MDIO_DATA, 0x0);
+ emac_wr(priv, MAC_MDIO_CONTROL, cmd);
+
+ ret = readl_poll_timeout(priv->iobase + MAC_MDIO_CONTROL, val,
+ !((val >> 15) & 0x1), 100, 10000);
+
+ if (ret)
+ return ret;
+
+ val = emac_rd(priv, MAC_MDIO_DATA);
+ return val;
+}
+
+static int emac_mii_write(struct mii_bus *bus, int phy_addr, int regnum,
+ u16 value)
+{
+ struct emac_priv *priv = bus->priv;
+ u32 cmd = 0, val;
+ int ret;
+
+ emac_wr(priv, MAC_MDIO_DATA, value);
+
+ cmd |= phy_addr & 0x1F;
+ cmd |= (regnum & 0x1F) << 5;
+ cmd |= MREGBIT_START_MDIO_TRANS;
+
+ emac_wr(priv, MAC_MDIO_CONTROL, cmd);
+
+ ret = readl_poll_timeout(priv->iobase + MAC_MDIO_CONTROL, val,
+ !((val >> 15) & 0x1), 100, 10000);
+
+ return ret;
+}
+
+static int emac_mdio_init(struct emac_priv *priv)
+{
+ struct device *dev = &priv->pdev->dev;
+ struct device_node *mii_np;
+ struct mii_bus *mii;
+ int ret;
+
+ mii = devm_mdiobus_alloc(dev);
+ if (!mii)
+ return -ENOMEM;
+
+ mii->priv = priv;
+ mii->name = "k1_emac_mii";
+ mii->read = emac_mii_read;
+ mii->write = emac_mii_write;
+ mii->parent = dev;
+ mii->phy_mask = 0xffffffff;
+ snprintf(mii->id, MII_BUS_ID_SIZE, "%s", priv->pdev->name);
+
+ mii_np = of_get_available_child_by_name(dev->of_node, "mdio-bus");
+
+ ret = devm_of_mdiobus_register(dev, mii, mii_np);
+ if (ret)
+ dev_err_probe(dev, ret, "Failed to register mdio bus\n");
+
+ of_node_put(mii_np);
+ return ret;
+}
+
+static void emac_get_strings(struct net_device *dev, u32 stringset, u8 *data)
+{
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < ARRAY_SIZE(emac_ethtool_stats); i++) {
+ memcpy(data, emac_ethtool_stats[i].str,
+ ETH_GSTRING_LEN);
+ data += ETH_GSTRING_LEN;
+ }
+ break;
+ }
+}
+
+static int emac_get_sset_count(struct net_device *dev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_STATS:
+ return ARRAY_SIZE(emac_ethtool_stats);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void emac_stats_update(struct emac_priv *priv)
+{
+ struct emac_hw_stats *hwstats = priv->hw_stats;
+ u32 *stats = (u32 *)hwstats;
+ int i;
+
+ for (i = 0; i < EMAC_TX_STATS_NUM; i++)
+ stats[i] = emac_tx_read_stat_cnt(priv, i);
+
+ for (i = 0; i < EMAC_RX_STATS_NUM; i++)
+ stats[i + EMAC_TX_STATS_NUM] = emac_rx_read_stat_cnt(priv, i);
+}
+
+static void emac_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct emac_priv *priv = netdev_priv(dev);
+ struct emac_hw_stats *hwstats;
+ unsigned long flags;
+ u32 *data_src;
+ u64 *data_dst;
+ int i;
+
+ hwstats = priv->hw_stats;
+
+ if (netif_running(dev) && netif_device_present(dev)) {
+ if (spin_trylock_irqsave(&priv->stats_lock, flags)) {
+ emac_stats_update(priv);
+ spin_unlock_irqrestore(&priv->stats_lock, flags);
+ }
+ }
+
+ data_dst = data;
+
+ for (i = 0; i < ARRAY_SIZE(emac_ethtool_stats); i++) {
+ data_src = (u32 *)hwstats + emac_ethtool_stats[i].offset;
+ *data_dst++ = (u64)(*data_src);
+ }
+}
+
+static int emac_ethtool_get_regs_len(struct net_device *dev)
+{
+ return (EMAC_DMA_REG_CNT + EMAC_MAC_REG_CNT) * sizeof(u32);
+}
+
+static void emac_ethtool_get_regs(struct net_device *dev,
+ struct ethtool_regs *regs, void *space)
+{
+ struct emac_priv *priv = netdev_priv(dev);
+ u32 *reg_space = space;
+ int i;
+
+ regs->version = 1;
+
+ for (i = 0; i < EMAC_DMA_REG_CNT; i++)
+ reg_space[i] = emac_rd(priv, DMA_CONFIGURATION + i * 4);
+
+ for (i = 0; i < EMAC_MAC_REG_CNT; i++)
+ reg_space[i + EMAC_DMA_REG_CNT] =
+ emac_rd(priv, MAC_GLOBAL_CONTROL + i * 4);
+}
+
+static void emac_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ strscpy(info->driver, DRIVER_NAME, sizeof(info->driver));
+ info->n_stats = ARRAY_SIZE(emac_ethtool_stats);
+}
+
+static void emac_tx_timeout_task(struct work_struct *work)
+{
+ struct net_device *ndev;
+ struct emac_priv *priv;
+
+ priv = container_of(work, struct emac_priv, tx_timeout_task);
+ ndev = priv->ndev;
+
+ rtnl_lock();
+
+ /* No need to reset if already down */
+ if (!netif_running(ndev)) {
+ rtnl_unlock();
+ return;
+ }
+
+ netdev_err(ndev, "MAC reset due to TX timeout\n");
+
+ netif_trans_update(ndev); /* prevent tx timeout */
+ dev_close(ndev);
+ dev_open(ndev, NULL);
+
+ rtnl_unlock();
+}
+
+static void emac_sw_init(struct emac_priv *priv)
+{
+ priv->dma_buf_sz = EMAC_DEFAULT_BUFSIZE;
+
+ priv->tx_ring.total_cnt = DEFAULT_TX_RING_NUM;
+ priv->rx_ring.total_cnt = DEFAULT_RX_RING_NUM;
+
+ spin_lock_init(&priv->stats_lock);
+
+ INIT_WORK(&priv->tx_timeout_task, emac_tx_timeout_task);
+
+ priv->tx_coal_frames = EMAC_TX_FRAMES;
+ priv->tx_coal_timeout = EMAC_TX_COAL_TIMEOUT;
+
+ timer_setup(&priv->txtimer, emac_tx_coal_timer, 0);
+}
+
+static irqreturn_t emac_interrupt_handler(int irq, void *dev_id)
+{
+ struct net_device *ndev = (struct net_device *)dev_id;
+ struct emac_priv *priv = netdev_priv(ndev);
+ bool should_schedule = false;
+ u32 status;
+ u32 clr = 0;
+
+ status = emac_rd(priv, DMA_STATUS_IRQ);
+
+ if (status & MREGBIT_TRANSMIT_TRANSFER_DONE_IRQ) {
+ clr |= MREGBIT_TRANSMIT_TRANSFER_DONE_IRQ;
+ should_schedule = true;
+ }
+
+ if (status & MREGBIT_TRANSMIT_DES_UNAVAILABLE_IRQ)
+ clr |= MREGBIT_TRANSMIT_DES_UNAVAILABLE_IRQ;
+
+ if (status & MREGBIT_TRANSMIT_DMA_STOPPED_IRQ)
+ clr |= MREGBIT_TRANSMIT_DMA_STOPPED_IRQ;
+
+ if (status & MREGBIT_RECEIVE_TRANSFER_DONE_IRQ) {
+ clr |= MREGBIT_RECEIVE_TRANSFER_DONE_IRQ;
+ should_schedule = true;
+ }
+
+ if (status & MREGBIT_RECEIVE_DES_UNAVAILABLE_IRQ)
+ clr |= MREGBIT_RECEIVE_DES_UNAVAILABLE_IRQ;
+
+ if (status & MREGBIT_RECEIVE_DMA_STOPPED_IRQ)
+ clr |= MREGBIT_RECEIVE_DMA_STOPPED_IRQ;
+
+ if (status & MREGBIT_RECEIVE_MISSED_FRAME_IRQ)
+ clr |= MREGBIT_RECEIVE_MISSED_FRAME_IRQ;
+
+ if (should_schedule) {
+ if (napi_schedule_prep(&priv->napi)) {
+ emac_disable_interrupt(priv);
+ __napi_schedule_irqoff(&priv->napi);
+ }
+ }
+
+ emac_wr(priv, DMA_STATUS_IRQ, clr);
+
+ return IRQ_HANDLED;
+}
+
+static void emac_configure_tx(struct emac_priv *priv)
+{
+ u32 val;
+
+ /* Set base address */
+ val = (u32)(priv->tx_ring.desc_dma_addr);
+ emac_wr(priv, DMA_TRANSMIT_BASE_ADDRESS, val);
+
+ /* Set TX inter-frame gap value, enable transmit */
+ val = emac_rd(priv, MAC_TRANSMIT_CONTROL);
+ val &= ~MREGBIT_IFG_LEN;
+ val |= MREGBIT_TRANSMIT_ENABLE;
+ val |= MREGBIT_TRANSMIT_AUTO_RETRY;
+ emac_wr(priv, MAC_TRANSMIT_CONTROL, val);
+
+ emac_wr(priv, DMA_TRANSMIT_AUTO_POLL_COUNTER, 0x0);
+
+ /* Start TX DMA */
+ val = emac_rd(priv, DMA_CONTROL);
+ val |= MREGBIT_START_STOP_TRANSMIT_DMA;
+ emac_wr(priv, DMA_CONTROL, val);
+}
+
+static void emac_configure_rx(struct emac_priv *priv)
+{
+ u32 val;
+
+ /* Set base address */
+ val = (u32)(priv->rx_ring.desc_dma_addr);
+ emac_wr(priv, DMA_RECEIVE_BASE_ADDRESS, val);
+
+ /* Enable receive */
+ val = emac_rd(priv, MAC_RECEIVE_CONTROL);
+ val |= MREGBIT_RECEIVE_ENABLE;
+ val |= MREGBIT_STORE_FORWARD;
+ emac_wr(priv, MAC_RECEIVE_CONTROL, val);
+
+ /* Start RX DMA */
+ val = emac_rd(priv, DMA_CONTROL);
+ val |= MREGBIT_START_STOP_RECEIVE_DMA;
+ emac_wr(priv, DMA_CONTROL, val);
+}
+
+static void emac_adjust_link(struct net_device *dev)
+{
+ struct emac_priv *priv = netdev_priv(dev);
+ struct phy_device *phydev = dev->phydev;
+ u32 ctrl;
+
+ if (phydev->link) {
+ ctrl = emac_rd(priv, MAC_GLOBAL_CONTROL);
+
+ /* Update duplex and speed from PHY */
+
+ if (!phydev->duplex)
+ ctrl &= ~MREGBIT_FULL_DUPLEX_MODE;
+ else
+ ctrl |= MREGBIT_FULL_DUPLEX_MODE;
+
+ ctrl &= ~MREGBIT_SPEED;
+
+ switch (phydev->speed) {
+ case SPEED_1000:
+ ctrl |= MREGBIT_SPEED_1000M;
+ break;
+ case SPEED_100:
+ ctrl |= MREGBIT_SPEED_100M;
+ break;
+ case SPEED_10:
+ ctrl |= MREGBIT_SPEED_10M;
+ break;
+ default:
+ netdev_err(dev, "Unknown speed: %d\n", phydev->speed);
+ phydev->speed = SPEED_UNKNOWN;
+ break;
+ }
+
+ emac_wr(priv, MAC_GLOBAL_CONTROL, ctrl);
+ }
+
+ phy_print_status(phydev);
+}
+
+static void emac_update_delay_line(struct emac_priv *priv)
+{
+ u32 mask = 0, val = 0;
+
+ mask |= EMAC_RX_DLINE_EN;
+ mask |= EMAC_RX_DLINE_STEP_MASK | EMAC_RX_DLINE_CODE_MASK;
+ mask |= EMAC_TX_DLINE_EN;
+ mask |= EMAC_TX_DLINE_STEP_MASK | EMAC_TX_DLINE_CODE_MASK;
+
+ switch (priv->phy_interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ val |= EMAC_RX_DLINE_EN;
+ val |= EMAC_DLINE_STEP_15P6 << EMAC_RX_DLINE_STEP_SHIFT;
+ val |= (priv->rx_delay << EMAC_RX_DLINE_CODE_SHIFT) &
+ EMAC_RX_DLINE_CODE_MASK;
+
+ val |= EMAC_TX_DLINE_EN;
+ val |= EMAC_DLINE_STEP_15P6 << EMAC_TX_DLINE_STEP_SHIFT;
+ val |= (priv->tx_delay << EMAC_TX_DLINE_CODE_SHIFT) &
+ EMAC_TX_DLINE_CODE_MASK;
+ break;
+ default:
+ break;
+ }
+
+ regmap_update_bits(priv->regmap_apmu,
+ priv->regmap_apmu_offset + APMU_EMAC_DLINE_REG,
+ mask, val);
+}
+
+static int emac_phy_connect(struct net_device *ndev)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+ struct device *dev = &priv->pdev->dev;
+ struct phy_device *phydev;
+ struct device_node *np;
+ int ret;
+
+ ret = of_get_phy_mode(dev->of_node, &priv->phy_interface);
+ if (ret) {
+ dev_err(dev, "No phy-mode found");
+ return ret;
+ }
+
+ np = of_parse_phandle(dev->of_node, "phy-handle", 0);
+ if (!np && of_phy_is_fixed_link(dev->of_node))
+ np = of_node_get(dev->of_node);
+
+ if (!np) {
+ dev_err(dev, "No PHY specified");
+ return -ENODEV;
+ }
+
+ ret = emac_phy_interface_config(priv);
+ if (ret)
+ goto err_node_put;
+
+ phydev = of_phy_connect(ndev, np, &emac_adjust_link, 0,
+ priv->phy_interface);
+ if (!phydev) {
+ dev_err(dev, "Could not attach to PHY\n");
+ ret = -ENODEV;
+ goto err_node_put;
+ }
+
+ phydev->mac_managed_pm = true;
+
+ ndev->phydev = phydev;
+
+ emac_update_delay_line(priv);
+
+err_node_put:
+ of_node_put(np);
+ return ret;
+}
+
+static int emac_up(struct emac_priv *priv)
+{
+ struct platform_device *pdev = priv->pdev;
+ struct net_device *ndev = priv->ndev;
+ int ret;
+
+ pm_runtime_get_sync(&pdev->dev);
+
+ ret = emac_phy_connect(ndev);
+ if (ret) {
+ dev_err(&pdev->dev, "emac_phy_connect failed\n");
+ goto err;
+ }
+
+ emac_init_hw(priv);
+
+ emac_set_mac_addr(priv, ndev->dev_addr);
+ emac_configure_tx(priv);
+ emac_configure_rx(priv);
+
+ emac_alloc_rx_desc_buffers(priv);
+
+ phy_start(ndev->phydev);
+
+ ret = request_irq(priv->irq, emac_interrupt_handler, IRQF_SHARED,
+ ndev->name, ndev);
+ if (ret) {
+ dev_err(&pdev->dev, "request_irq failed\n");
+ goto request_irq_failed;
+ }
+
+ /* Don't enable MAC interrupts */
+ emac_wr(priv, MAC_INTERRUPT_ENABLE, 0x0);
+
+ /* Enable DMA interrupts */
+ emac_wr(priv, DMA_INTERRUPT_ENABLE,
+ MREGBIT_TRANSMIT_TRANSFER_DONE_INTR_ENABLE |
+ MREGBIT_TRANSMIT_DMA_STOPPED_INTR_ENABLE |
+ MREGBIT_RECEIVE_TRANSFER_DONE_INTR_ENABLE |
+ MREGBIT_RECEIVE_DMA_STOPPED_INTR_ENABLE |
+ MREGBIT_RECEIVE_MISSED_FRAME_INTR_ENABLE);
+
+ napi_enable(&priv->napi);
+
+ netif_start_queue(ndev);
+ return 0;
+
+request_irq_failed:
+ emac_reset_hw(priv);
+ phy_stop(ndev->phydev);
+ phy_disconnect(ndev->phydev);
+
+err:
+ pm_runtime_put_sync(&pdev->dev);
+ return ret;
+}
+
+static int emac_down(struct emac_priv *priv)
+{
+ struct platform_device *pdev = priv->pdev;
+ struct net_device *ndev = priv->ndev;
+
+ netif_stop_queue(ndev);
+
+ phy_stop(ndev->phydev);
+ phy_disconnect(ndev->phydev);
+
+ emac_wr(priv, MAC_INTERRUPT_ENABLE, 0x0);
+ emac_wr(priv, DMA_INTERRUPT_ENABLE, 0x0);
+
+ free_irq(priv->irq, ndev);
+
+ napi_disable(&priv->napi);
+
+ emac_reset_hw(priv);
+
+ pm_runtime_put_sync(&pdev->dev);
+ return 0;
+}
+
+/* Called when net interface is brought up. */
+static int emac_open(struct net_device *ndev)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+ struct device *dev = &priv->pdev->dev;
+
+ int ret;
+
+ ret = emac_alloc_tx_resources(priv);
+ if (ret) {
+ dev_err(dev, "Error when setting up the Tx resources\n");
+ goto emac_alloc_tx_resource_fail;
+ }
+
+ ret = emac_alloc_rx_resources(priv);
+ if (ret) {
+ dev_err(dev, "Error when setting up the Rx resources\n");
+ goto emac_alloc_rx_resource_fail;
+ }
+
+ ret = emac_up(priv);
+ if (ret) {
+ dev_err(dev, "Error when bringing interface up\n");
+ goto emac_up_fail;
+ }
+ return 0;
+
+emac_up_fail:
+ emac_free_rx_resources(priv);
+emac_alloc_rx_resource_fail:
+ emac_free_tx_resources(priv);
+emac_alloc_tx_resource_fail:
+ return ret;
+}
+
+/* Called when interface is brought down. */
+static int emac_close(struct net_device *ndev)
+{
+ struct emac_priv *priv = netdev_priv(ndev);
+
+ emac_down(priv);
+ emac_free_tx_resources(priv);
+ emac_free_rx_resources(priv);
+
+ return 0;
+}
+
+static const struct ethtool_ops emac_ethtool_ops = {
+ .get_link_ksettings = phy_ethtool_get_link_ksettings,
+ .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_drvinfo = emac_get_drvinfo,
+ .nway_reset = phy_ethtool_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_strings = emac_get_strings,
+ .get_sset_count = emac_get_sset_count,
+ .get_ethtool_stats = emac_get_ethtool_stats,
+ .get_regs = emac_ethtool_get_regs,
+ .get_regs_len = emac_ethtool_get_regs_len,
+};
+
+static const struct net_device_ops emac_netdev_ops = {
+ .ndo_open = emac_open,
+ .ndo_stop = emac_close,
+ .ndo_start_xmit = emac_start_xmit,
+ .ndo_set_mac_address = emac_set_mac_address,
+ .ndo_eth_ioctl = phy_do_ioctl_running,
+ .ndo_change_mtu = emac_change_mtu,
+ .ndo_tx_timeout = emac_tx_timeout,
+ .ndo_set_rx_mode = emac_rx_mode_set,
+};
+
+/* Currently we always use 15.6 ps/step for the delay line */
+
+static u32 delay_ps_to_unit(u32 ps)
+{
+ return DIV_ROUND_CLOSEST(ps * 10, 156);
+}
+
+static u32 delay_unit_to_ps(u32 unit)
+{
+ return DIV_ROUND_CLOSEST(unit * 156, 10);
+}
+
+#define EMAC_MAX_DELAY_UNIT \
+ (EMAC_TX_DLINE_CODE_MASK >> EMAC_TX_DLINE_CODE_SHIFT)
+
+/* Minus one just to be safe from rounding errors */
+#define EMAC_MAX_DELAY_PS (delay_unit_to_ps(EMAC_MAX_DELAY_UNIT - 1))
+
+static int emac_config_dt(struct platform_device *pdev, struct emac_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ u8 mac_addr[ETH_ALEN] = { 0 };
+ int ret;
+
+ priv->iobase = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->iobase))
+ return dev_err_probe(dev, PTR_ERR(priv->iobase),
+ "ioremap failed\n");
+
+ priv->regmap_apmu =
+ syscon_regmap_lookup_by_phandle_args(np, "spacemit,apmu", 1,
+ &priv->regmap_apmu_offset);
+
+ if (IS_ERR(priv->regmap_apmu))
+ return dev_err_probe(dev, PTR_ERR(priv->regmap_apmu),
+ "failed to get syscon\n");
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq < 0)
+ return -ENXIO;
+
+ ret = of_get_mac_address(np, mac_addr);
+ if (ret) {
+ if (ret == -EPROBE_DEFER)
+ return dev_err_probe(dev, ret,
+ "Can't get MAC address\n");
+
+ dev_info(&pdev->dev, "Using random MAC address\n");
+ eth_hw_addr_random(priv->ndev);
+ } else {
+ eth_hw_addr_set(priv->ndev, mac_addr);
+ }
+
+ priv->tx_delay = 0;
+ priv->rx_delay = 0;
+
+ of_property_read_u32(np, "tx-internal-delay-ps", &priv->tx_delay);
+ of_property_read_u32(np, "rx-internal-delay-ps", &priv->rx_delay);
+
+ if (priv->tx_delay > EMAC_MAX_DELAY_PS) {
+ dev_err(&pdev->dev,
+ "tx-internal-delay-ps too large: max %d, got %d",
+ EMAC_MAX_DELAY_PS, priv->tx_delay);
+ return -EINVAL;
+ }
+
+ if (priv->rx_delay > EMAC_MAX_DELAY_PS) {
+ dev_err(&pdev->dev,
+ "rx-internal-delay-ps too large: max %d, got %d",
+ EMAC_MAX_DELAY_PS, priv->rx_delay);
+ return -EINVAL;
+ }
+
+ priv->tx_delay = delay_ps_to_unit(priv->tx_delay);
+ priv->rx_delay = delay_ps_to_unit(priv->rx_delay);
+
+ return 0;
+}
+
+static int emac_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct reset_control *reset;
+ struct net_device *ndev;
+ struct emac_priv *priv;
+ int ret;
+
+ ndev = devm_alloc_etherdev(dev, sizeof(struct emac_priv));
+ if (!ndev)
+ return -ENOMEM;
+
+ ndev->hw_features = NETIF_F_SG;
+ ndev->features |= ndev->hw_features;
+
+ ndev->min_mtu = ETH_MIN_MTU;
+ ndev->max_mtu = EMAC_RX_BUF_4K - (ETH_HLEN + ETH_FCS_LEN);
+
+ priv = netdev_priv(ndev);
+ priv->ndev = ndev;
+ priv->pdev = pdev;
+ platform_set_drvdata(pdev, priv);
+ priv->hw_stats = devm_kzalloc(dev, sizeof(*priv->hw_stats), GFP_KERNEL);
+ if (!priv->hw_stats) {
+ dev_err(dev, "Failed to allocate memory for stats\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ ret = emac_config_dt(pdev, priv);
+ if (ret < 0) {
+ dev_err(dev, "Configuration failed\n");
+ goto err;
+ }
+
+ ndev->watchdog_timeo = 5 * HZ;
+ ndev->base_addr = (unsigned long)priv->iobase;
+ ndev->irq = priv->irq;
+
+ ndev->ethtool_ops = &emac_ethtool_ops;
+ ndev->netdev_ops = &emac_netdev_ops;
+
+ devm_pm_runtime_enable(&pdev->dev);
+
+ priv->bus_clk = devm_clk_get_enabled(&pdev->dev, NULL);
+ if (IS_ERR(priv->bus_clk)) {
+ ret = dev_err_probe(dev, PTR_ERR(priv->bus_clk),
+ "Failed to get clock\n");
+ goto err;
+ }
+
+ reset = devm_reset_control_get_optional_exclusive_deasserted(&pdev->dev,
+ NULL);
+ if (IS_ERR(reset)) {
+ ret = dev_err_probe(dev, PTR_ERR(reset),
+ "Failed to get reset\n");
+ goto err;
+ }
+
+ emac_sw_init(priv);
+
+ if (of_phy_is_fixed_link(dev->of_node)) {
+ ret = of_phy_register_fixed_link(dev->of_node);
+ if (ret) {
+ dev_err_probe(dev, ret,
+ "Failed to register fixed-link");
+ goto err_timer_delete;
+ }
+ }
+
+ ret = emac_mdio_init(priv);
+ if (ret)
+ goto err_timer_delete;
+
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+
+ ret = devm_register_netdev(dev, ndev);
+ if (ret) {
+ dev_err(dev, "devm_register_netdev failed\n");
+ goto err_timer_delete;
+ }
+
+ netif_napi_add(ndev, &priv->napi, emac_rx_poll);
+ netif_carrier_off(ndev);
+
+ return 0;
+
+err_timer_delete:
+ timer_delete_sync(&priv->txtimer);
+err:
+ return ret;
+}
+
+static void emac_remove(struct platform_device *pdev)
+{
+ struct emac_priv *priv = platform_get_drvdata(pdev);
+
+ emac_reset_hw(priv);
+}
+
+static int emac_resume(struct device *dev)
+{
+ struct emac_priv *priv = dev_get_drvdata(dev);
+ struct net_device *ndev = priv->ndev;
+ int ret;
+
+ ret = clk_prepare_enable(priv->bus_clk);
+ if (ret < 0) {
+ dev_err(dev, "Failed to enable bus clock: %d\n", ret);
+ return ret;
+ }
+
+ if (!netif_running(ndev))
+ return 0;
+
+ emac_open(ndev);
+ netif_device_attach(ndev);
+ return 0;
+}
+
+static int emac_suspend(struct device *dev)
+{
+ struct emac_priv *priv = dev_get_drvdata(dev);
+ struct net_device *ndev = priv->ndev;
+
+ if (!ndev || !netif_running(ndev)) {
+ clk_disable_unprepare(priv->bus_clk);
+ return 0;
+ }
+
+ emac_close(ndev);
+ clk_disable_unprepare(priv->bus_clk);
+ netif_device_detach(ndev);
+ return 0;
+}
+
+static const struct dev_pm_ops emac_pm_ops = {
+ SYSTEM_SLEEP_PM_OPS(emac_suspend, emac_resume)
+};
+
+static const struct of_device_id emac_of_match[] = {
+ { .compatible = "spacemit,k1-emac" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, emac_of_match);
+
+static struct platform_driver emac_driver = {
+ .probe = emac_probe,
+ .remove = emac_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = of_match_ptr(emac_of_match),
+ .pm = &emac_pm_ops,
+ },
+};
+module_platform_driver(emac_driver);
+
+MODULE_DESCRIPTION("SpacemiT K1 Ethernet driver");
+MODULE_AUTHOR("Vivian Wang <wangruikang@iscas.ac.cn>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/spacemit/k1_emac.h b/drivers/net/ethernet/spacemit/k1_emac.h
new file mode 100644
index 0000000000000000000000000000000000000000..b4ccd938a46c0062c48b4a6b5a4f2a57afa01abd
--- /dev/null
+++ b/drivers/net/ethernet/spacemit/k1_emac.h
@@ -0,0 +1,420 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * SpacemiT K1 Ethernet hardware definitions
+ *
+ * Copyright (C) 2023-2025 SpacemiT (Hangzhou) Technology Co. Ltd
+ * Copyright (C) 2025 Vivian Wang <wangruikang@iscas.ac.cn>
+ */
+
+#ifndef _K1_EMAC_H_
+#define _K1_EMAC_H_
+
+/* APMU syscon registers */
+
+#define APMU_EMAC_CTRL_REG 0x0
+
+#define PHY_INTF_RGMII BIT(2)
+
+/*
+ * Only valid for RMII mode
+ * 0: Ref clock from External PHY
+ * 1: Ref clock from SoC
+ */
+#define REF_CLK_SEL BIT(3)
+
+/*
+ * Function clock select
+ * 0: 208 MHz
+ * 1: 312 MHz
+ */
+#define FUNC_CLK_SEL BIT(4)
+
+/* Only valid for RMII, invert TX clk */
+#define RMII_TX_CLK_SEL BIT(6)
+
+/* Only valid for RMII, invert RX clk */
+#define RMII_RX_CLK_SEL BIT(7)
+
+/*
+ * Only valid for RGMII
+ * 0: TX clk from RX clk
+ * 1: TX clk from SoC
+ */
+#define RGMII_TX_CLK_SEL BIT(8)
+
+#define PHY_IRQ_EN BIT(12)
+#define AXI_SINGLE_ID BIT(13)
+
+#define RMII_TX_PHASE_SHIFT 16
+#define RMII_TX_PHASE_MASK GENMASK(18, 16)
+#define RMII_RX_PHASE_SHIFT 20
+#define RMII_RX_PHASE_MASK GENMASK(22, 20)
+
+#define RGMII_TX_PHASE_SHIFT 24
+#define RGMII_TX_PHASE_MASK GENMASK(26, 24)
+#define RGMII_RX_PHASE_SHIFT 28
+#define RGMII_RX_PHASE_MASK GENMASK(30, 28)
+
+#define APMU_EMAC_DLINE_REG 0x4
+
+#define EMAC_RX_DLINE_EN BIT(0)
+#define EMAC_RX_DLINE_STEP_SHIFT 4
+#define EMAC_RX_DLINE_STEP_MASK GENMASK(5, 4)
+#define EMAC_RX_DLINE_CODE_SHIFT 8
+#define EMAC_RX_DLINE_CODE_MASK GENMASK(15, 8)
+
+#define EMAC_TX_DLINE_EN BIT(16)
+#define EMAC_TX_DLINE_STEP_SHIFT 20
+#define EMAC_TX_DLINE_STEP_MASK GENMASK(21, 20)
+#define EMAC_TX_DLINE_CODE_SHIFT 24
+#define EMAC_TX_DLINE_CODE_MASK GENMASK(31, 24)
+
+#define EMAC_DLINE_STEP_15P6 0 /* 15.6 ps/step */
+#define EMAC_DLINE_STEP_24P4 1 /* 24.4 ps/step */
+#define EMAC_DLINE_STEP_29P7 2 /* 29.7 ps/step */
+#define EMAC_DLINE_STEP_35P1 3 /* 35.1 ps/step */
+
+/* DMA register set */
+#define DMA_CONFIGURATION 0x0000
+#define DMA_CONTROL 0x0004
+#define DMA_STATUS_IRQ 0x0008
+#define DMA_INTERRUPT_ENABLE 0x000c
+
+#define DMA_TRANSMIT_AUTO_POLL_COUNTER 0x0010
+#define DMA_TRANSMIT_POLL_DEMAND 0x0014
+#define DMA_RECEIVE_POLL_DEMAND 0x0018
+
+#define DMA_TRANSMIT_BASE_ADDRESS 0x001c
+#define DMA_RECEIVE_BASE_ADDRESS 0x0020
+#define DMA_MISSED_FRAME_COUNTER 0x0024
+#define DMA_STOP_FLUSH_COUNTER 0x0028
+
+#define DMA_RECEIVE_IRQ_MITIGATION_CTRL 0x002c
+
+#define DMA_CURRENT_TRANSMIT_DESCRIPTOR_POINTER 0x0030
+#define DMA_CURRENT_TRANSMIT_BUFFER_POINTER 0x0034
+#define DMA_CURRENT_RECEIVE_DESCRIPTOR_POINTER 0x0038
+#define DMA_CURRENT_RECEIVE_BUFFER_POINTER 0x003c
+
+/* MAC Register set */
+#define MAC_GLOBAL_CONTROL 0x0100
+#define MAC_TRANSMIT_CONTROL 0x0104
+#define MAC_RECEIVE_CONTROL 0x0108
+#define MAC_MAXIMUM_FRAME_SIZE 0x010c
+#define MAC_TRANSMIT_JABBER_SIZE 0x0110
+#define MAC_RECEIVE_JABBER_SIZE 0x0114
+#define MAC_ADDRESS_CONTROL 0x0118
+#define MAC_MDIO_CLK_DIV 0x011c
+#define MAC_ADDRESS1_HIGH 0x0120
+#define MAC_ADDRESS1_MED 0x0124
+#define MAC_ADDRESS1_LOW 0x0128
+#define MAC_ADDRESS2_HIGH 0x012c
+#define MAC_ADDRESS2_MED 0x0130
+#define MAC_ADDRESS2_LOW 0x0134
+#define MAC_ADDRESS3_HIGH 0x0138
+#define MAC_ADDRESS3_MED 0x013c
+#define MAC_ADDRESS3_LOW 0x0140
+#define MAC_ADDRESS4_HIGH 0x0144
+#define MAC_ADDRESS4_MED 0x0148
+#define MAC_ADDRESS4_LOW 0x014c
+#define MAC_MULTICAST_HASH_TABLE1 0x0150
+#define MAC_MULTICAST_HASH_TABLE2 0x0154
+#define MAC_MULTICAST_HASH_TABLE3 0x0158
+#define MAC_MULTICAST_HASH_TABLE4 0x015c
+#define MAC_FC_CONTROL 0x0160
+#define MAC_FC_PAUSE_FRAME_GENERATE 0x0164
+#define MAC_FC_SOURCE_ADDRESS_HIGH 0x0168
+#define MAC_FC_SOURCE_ADDRESS_MED 0x016c
+#define MAC_FC_SOURCE_ADDRESS_LOW 0x0170
+#define MAC_FC_DESTINATION_ADDRESS_HIGH 0x0174
+#define MAC_FC_DESTINATION_ADDRESS_MED 0x0178
+#define MAC_FC_DESTINATION_ADDRESS_LOW 0x017c
+#define MAC_FC_PAUSE_TIME_VALUE 0x0180
+#define MAC_MDIO_CONTROL 0x01a0
+#define MAC_MDIO_DATA 0x01a4
+#define MAC_RX_STATCTR_CONTROL 0x01a8
+#define MAC_RX_STATCTR_DATA_HIGH 0x01ac
+#define MAC_RX_STATCTR_DATA_LOW 0x01b0
+#define MAC_TX_STATCTR_CONTROL 0x01b4
+#define MAC_TX_STATCTR_DATA_HIGH 0x01b8
+#define MAC_TX_STATCTR_DATA_LOW 0x01bc
+#define MAC_TRANSMIT_FIFO_ALMOST_FULL 0x01c0
+#define MAC_TRANSMIT_PACKET_START_THRESHOLD 0x01c4
+#define MAC_RECEIVE_PACKET_START_THRESHOLD 0x01c8
+#define MAC_STATUS_IRQ 0x01e0
+#define MAC_INTERRUPT_ENABLE 0x01e4
+
+/* Used for register dump */
+#define EMAC_DMA_REG_CNT 16
+#define EMAC_MAC_REG_CNT 124
+
+/* DMA_CONFIGURATION (0x0000) */
+
+/*
+ * 0-DMA controller in normal operation mode,
+ * 1-DMA controller reset to default state,
+ * clearing all internal state information
+ */
+#define MREGBIT_SOFTWARE_RESET BIT(0)
+
+#define MREGBIT_BURST_1WORD BIT(1)
+#define MREGBIT_BURST_2WORD BIT(2)
+#define MREGBIT_BURST_4WORD BIT(3)
+#define MREGBIT_BURST_8WORD BIT(4)
+#define MREGBIT_BURST_16WORD BIT(5)
+#define MREGBIT_BURST_32WORD BIT(6)
+#define MREGBIT_BURST_64WORD BIT(7)
+#define MREGBIT_BURST_LENGTH GENMASK(7, 1)
+#define MREGBIT_DESCRIPTOR_SKIP_LENGTH GENMASK(12, 8)
+
+/* For Receive and Transmit DMA operate in Big-Endian mode for Descriptors. */
+#define MREGBIT_DESCRIPTOR_BYTE_ORDERING BIT(13)
+
+#define MREGBIT_BIG_LITLE_ENDIAN BIT(14)
+#define MREGBIT_TX_RX_ARBITRATION BIT(15)
+#define MREGBIT_WAIT_FOR_DONE BIT(16)
+#define MREGBIT_STRICT_BURST BIT(17)
+#define MREGBIT_DMA_64BIT_MODE BIT(18)
+
+/* DMA_CONTROL (0x0004) */
+#define MREGBIT_START_STOP_TRANSMIT_DMA BIT(0)
+#define MREGBIT_START_STOP_RECEIVE_DMA BIT(1)
+
+/* DMA_STATUS_IRQ (0x0008) */
+#define MREGBIT_TRANSMIT_TRANSFER_DONE_IRQ BIT(0)
+#define MREGBIT_TRANSMIT_DES_UNAVAILABLE_IRQ BIT(1)
+#define MREGBIT_TRANSMIT_DMA_STOPPED_IRQ BIT(2)
+#define MREGBIT_RECEIVE_TRANSFER_DONE_IRQ BIT(4)
+#define MREGBIT_RECEIVE_DES_UNAVAILABLE_IRQ BIT(5)
+#define MREGBIT_RECEIVE_DMA_STOPPED_IRQ BIT(6)
+#define MREGBIT_RECEIVE_MISSED_FRAME_IRQ BIT(7)
+#define MREGBIT_MAC_IRQ BIT(8)
+#define MREGBIT_TRANSMIT_DMA_STATE GENMASK(18, 16)
+#define MREGBIT_RECEIVE_DMA_STATE GENMASK(23, 20)
+
+/* DMA_INTERRUPT_ENABLE (0x000c) */
+#define MREGBIT_TRANSMIT_TRANSFER_DONE_INTR_ENABLE BIT(0)
+#define MREGBIT_TRANSMIT_DES_UNAVAILABLE_INTR_ENABLE BIT(1)
+#define MREGBIT_TRANSMIT_DMA_STOPPED_INTR_ENABLE BIT(2)
+#define MREGBIT_RECEIVE_TRANSFER_DONE_INTR_ENABLE BIT(4)
+#define MREGBIT_RECEIVE_DES_UNAVAILABLE_INTR_ENABLE BIT(5)
+#define MREGBIT_RECEIVE_DMA_STOPPED_INTR_ENABLE BIT(6)
+#define MREGBIT_RECEIVE_MISSED_FRAME_INTR_ENABLE BIT(7)
+#define MREGBIT_MAC_INTR_ENABLE BIT(8)
+
+/* DMA_RECEIVE_IRQ_MITIGATION_CTRL (0x002c) */
+#define MREGBIT_RECEIVE_IRQ_FRAME_COUNTER_MASK GENMASK(7, 0)
+#define MREGBIT_RECEIVE_IRQ_TIMEOUT_COUNTER_SHIFT 8
+#define MREGBIT_RECEIVE_IRQ_TIMEOUT_COUNTER_MASK GENMASK(27, 8)
+#define MREGBIT_RECEIVE_IRQ_FRAME_COUNTER_MODE BIT(30)
+#define MREGBIT_RECEIVE_IRQ_MITIGATION_ENABLE BIT(31)
+
+/* MAC_GLOBAL_CONTROL (0x0100) */
+#define MREGBIT_SPEED GENMASK(1, 0)
+#define MREGBIT_SPEED_10M 0x0
+#define MREGBIT_SPEED_100M BIT(0)
+#define MREGBIT_SPEED_1000M BIT(1)
+#define MREGBIT_FULL_DUPLEX_MODE BIT(2)
+#define MREGBIT_RESET_RX_STAT_COUNTERS BIT(3)
+#define MREGBIT_RESET_TX_STAT_COUNTERS BIT(4)
+#define MREGBIT_UNICAST_WAKEUP_MODE BIT(8)
+#define MREGBIT_MAGIC_PACKET_WAKEUP_MODE BIT(9)
+
+/* MAC_TRANSMIT_CONTROL (0x0104) */
+#define MREGBIT_TRANSMIT_ENABLE BIT(0)
+#define MREGBIT_INVERT_FCS BIT(1)
+#define MREGBIT_DISABLE_FCS_INSERT BIT(2)
+#define MREGBIT_TRANSMIT_AUTO_RETRY BIT(3)
+#define MREGBIT_IFG_LEN GENMASK(6, 4)
+#define MREGBIT_PREAMBLE_LENGTH GENMASK(9, 7)
+
+/* MAC_RECEIVE_CONTROL (0x0108) */
+#define MREGBIT_RECEIVE_ENABLE BIT(0)
+#define MREGBIT_DISABLE_FCS_CHECK BIT(1)
+#define MREGBIT_STRIP_FCS BIT(2)
+#define MREGBIT_STORE_FORWARD BIT(3)
+#define MREGBIT_STATUS_FIRST BIT(4)
+#define MREGBIT_PASS_BAD_FRAMES BIT(5)
+#define MREGBIT_ACOOUNT_VLAN BIT(6)
+
+/* MAC_MAXIMUM_FRAME_SIZE (0x010c) */
+#define MREGBIT_MAX_FRAME_SIZE GENMASK(13, 0)
+
+/* MAC_TRANSMIT_JABBER_SIZE (0x0110) */
+#define MREGBIT_TRANSMIT_JABBER_SIZE GENMASK(15, 0)
+
+/* MAC_RECEIVE_JABBER_SIZE (0x0114) */
+#define MREGBIT_RECEIVE_JABBER_SIZE GENMASK(15, 0)
+
+/* MAC_ADDRESS_CONTROL (0x0118) */
+#define MREGBIT_MAC_ADDRESS1_ENABLE BIT(0)
+#define MREGBIT_MAC_ADDRESS2_ENABLE BIT(1)
+#define MREGBIT_MAC_ADDRESS3_ENABLE BIT(2)
+#define MREGBIT_MAC_ADDRESS4_ENABLE BIT(3)
+#define MREGBIT_INVERSE_MAC_ADDRESS1_ENABLE BIT(4)
+#define MREGBIT_INVERSE_MAC_ADDRESS2_ENABLE BIT(5)
+#define MREGBIT_INVERSE_MAC_ADDRESS3_ENABLE BIT(6)
+#define MREGBIT_INVERSE_MAC_ADDRESS4_ENABLE BIT(7)
+#define MREGBIT_PROMISCUOUS_MODE BIT(8)
+
+/* MAC_FC_CONTROL (0x0160) */
+#define MREGBIT_FC_DECODE_ENABLE BIT(0)
+#define MREGBIT_FC_GENERATION_ENABLE BIT(1)
+#define MREGBIT_AUTO_FC_GENERATION_ENABLE BIT(2)
+#define MREGBIT_MULTICAST_MODE BIT(3)
+#define MREGBIT_BLOCK_PAUSE_FRAMES BIT(4)
+
+/* MAC_FC_PAUSE_FRAME_GENERATE (0x0164) */
+#define MREGBIT_GENERATE_PAUSE_FRAME BIT(0)
+
+/* MAC_FC_PAUSE_TIME_VALUE (0x0180) */
+#define MREGBIT_MAC_FC_PAUSE_TIME GENMASK(15, 0)
+
+/* MAC_MDIO_CONTROL (0x01a0) */
+#define MREGBIT_PHY_ADDRESS GENMASK(4, 0)
+#define MREGBIT_REGISTER_ADDRESS GENMASK(9, 5)
+#define MREGBIT_MDIO_READ_WRITE BIT(10)
+#define MREGBIT_START_MDIO_TRANS BIT(15)
+
+/* MAC_MDIO_DATA (0x01a4) */
+#define MREGBIT_MDIO_DATA GENMASK(15, 0)
+
+/* MAC_RX_STATCTR_CONTROL (0x01a8) */
+#define MREGBIT_RX_COUNTER_NUMBER GENMASK(4, 0)
+#define MREGBIT_START_RX_COUNTER_READ BIT(15)
+
+/* MAC_RX_STATCTR_DATA_HIGH (0x01ac) */
+#define MREGBIT_RX_STATCTR_DATA_HIGH GENMASK(15, 0)
+/* MAC_RX_STATCTR_DATA_LOW (0x01b0) */
+#define MREGBIT_RX_STATCTR_DATA_LOW GENMASK(15, 0)
+
+/* MAC_TX_STATCTR_CONTROL (0x01b4) */
+#define MREGBIT_TX_COUNTER_NUMBER GENMASK(4, 0)
+#define MREGBIT_START_TX_COUNTER_READ BIT(15)
+
+/* MAC_TX_STATCTR_DATA_HIGH (0x01b8) */
+#define MREGBIT_TX_STATCTR_DATA_HIGH GENMASK(15, 0)
+/* MAC_TX_STATCTR_DATA_LOW (0x01bc) */
+#define MREGBIT_TX_STATCTR_DATA_LOW GENMASK(15, 0)
+
+/* MAC_TRANSMIT_FIFO_ALMOST_FULL (0x01c0) */
+#define MREGBIT_TX_FIFO_AF GENMASK(13, 0)
+
+/* MAC_TRANSMIT_PACKET_START_THRESHOLD (0x01c4) */
+#define MREGBIT_TX_PACKET_START_THRESHOLD GENMASK(13, 0)
+
+/* MAC_RECEIVE_PACKET_START_THRESHOLD (0x01c8) */
+#define MREGBIT_RX_PACKET_START_THRESHOLD GENMASK(13, 0)
+
+/* MAC_STATUS_IRQ (0x01e0) */
+#define MREGBIT_MAC_UNDERRUN_IRQ BIT(0)
+#define MREGBIT_MAC_JABBER_IRQ BIT(1)
+
+/* MAC_INTERRUPT_ENABLE (0x01e4) */
+#define MREGBIT_MAC_UNDERRUN_INTERRUPT_ENABLE BIT(0)
+#define MREGBIT_JABBER_INTERRUPT_ENABLE BIT(1)
+
+/* RX DMA descriptor */
+
+#define RX_DESC_0_FRAME_PACKET_LENGTH_SHIFT 0
+#define RX_DESC_0_FRAME_PACKET_LENGTH_MASK GENMASK(13, 0)
+#define RX_DESC_0_FRAME_ALIGN_ERR BIT(14)
+#define RX_DESC_0_FRAME_RUNT BIT(15)
+#define RX_DESC_0_FRAME_ETHERNET_TYPE BIT(16)
+#define RX_DESC_0_FRAME_VLAN BIT(17)
+#define RX_DESC_0_FRAME_MULTICAST BIT(18)
+#define RX_DESC_0_FRAME_BROADCAST BIT(19)
+#define RX_DESC_0_FRAME_CRC_ERR BIT(20)
+#define RX_DESC_0_FRAME_MAX_LEN_ERR BIT(21)
+#define RX_DESC_0_FRAME_JABBER_ERR BIT(22)
+#define RX_DESC_0_FRAME_LENGTH_ERR BIT(23)
+#define RX_DESC_0_FRAME_MAC_ADDR1_MATCH BIT(24)
+#define RX_DESC_0_FRAME_MAC_ADDR2_MATCH BIT(25)
+#define RX_DESC_0_FRAME_MAC_ADDR3_MATCH BIT(26)
+#define RX_DESC_0_FRAME_MAC_ADDR4_MATCH BIT(27)
+#define RX_DESC_0_FRAME_PAUSE_CTRL BIT(28)
+#define RX_DESC_0_LAST_DESCRIPTOR BIT(29)
+#define RX_DESC_0_FIRST_DESCRIPTOR BIT(30)
+#define RX_DESC_0_OWN BIT(31)
+
+#define RX_DESC_1_BUFFER_SIZE_1_SHIFT 0
+#define RX_DESC_1_BUFFER_SIZE_1_MASK GENMASK(11, 0)
+#define RX_DESC_1_BUFFER_SIZE_2_SHIFT 12
+#define RX_DESC_1_BUFFER_SIZE_2_MASK GENMASK(23, 12)
+ /* [24] reserved */
+#define RX_DESC_1_SECOND_ADDRESS_CHAINED BIT(25)
+#define RX_DESC_1_END_RING BIT(26)
+ /* [29:27] reserved */
+#define RX_DESC_1_RX_TIMESTAMP BIT(30)
+#define RX_DESC_1_PTP_PKT BIT(31)
+
+/* TX DMA descriptor */
+
+ /* [29:0] unused */
+#define TX_DESC_0_TX_TIMESTAMP BIT(30)
+#define TX_DESC_0_OWN BIT(31)
+
+#define TX_DESC_1_BUFFER_SIZE_1_SHIFT 0
+#define TX_DESC_1_BUFFER_SIZE_1_MASK GENMASK(11, 0)
+#define TX_DESC_1_BUFFER_SIZE_2_SHIFT 12
+#define TX_DESC_1_BUFFER_SIZE_2_MASK GENMASK(23, 12)
+#define TX_DESC_1_FORCE_EOP_ERROR BIT(24)
+#define TX_DESC_1_SECOND_ADDRESS_CHAINED BIT(25)
+#define TX_DESC_1_END_RING BIT(26)
+#define TX_DESC_1_DISABLE_PADDING BIT(27)
+#define TX_DESC_1_ADD_CRC_DISABLE BIT(28)
+#define TX_DESC_1_FIRST_SEGMENT BIT(29)
+#define TX_DESC_1_LAST_SEGMENT BIT(30)
+#define TX_DESC_1_INTERRUPT_ON_COMPLETION BIT(31)
+
+struct emac_desc {
+ u32 desc0;
+ u32 desc1;
+ u32 buffer_addr_1;
+ u32 buffer_addr_2;
+};
+
+struct emac_hw_stats {
+ u32 tx_ok_pkts;
+ u32 tx_total_pkts;
+ u32 tx_ok_bytes;
+ u32 tx_err_pkts;
+ u32 tx_singleclsn_pkts;
+ u32 tx_multiclsn_pkts;
+ u32 tx_lateclsn_pkts;
+ u32 tx_excessclsn_pkts;
+ u32 tx_unicast_pkts;
+ u32 tx_multicast_pkts;
+ u32 tx_broadcast_pkts;
+ u32 tx_pause_pkts;
+ u32 rx_ok_pkts;
+ u32 rx_total_pkts;
+ u32 rx_crc_err_pkts;
+ u32 rx_align_err_pkts;
+ u32 rx_err_total_pkts;
+ u32 rx_ok_bytes;
+ u32 rx_total_bytes;
+ u32 rx_unicast_pkts;
+ u32 rx_multicast_pkts;
+ u32 rx_broadcast_pkts;
+ u32 rx_pause_pkts;
+ u32 rx_len_err_pkts;
+ u32 rx_len_undersize_pkts;
+ u32 rx_len_oversize_pkts;
+ u32 rx_len_fragment_pkts;
+ u32 rx_len_jabber_pkts;
+ u32 rx_64_pkts;
+ u32 rx_65_127_pkts;
+ u32 rx_128_255_pkts;
+ u32 rx_256_511_pkts;
+ u32 rx_512_1023_pkts;
+ u32 rx_1024_1518_pkts;
+ u32 rx_1519_plus_pkts;
+ u32 rx_drp_fifo_full_pkts;
+ u32 rx_truncate_fifo_full_pkts;
+};
+
+#define EMAC_TX_STATS_NUM 12
+#define EMAC_RX_STATS_NUM 25
+
+#endif /* _K1_EMAC_H_ */
--
2.49.0
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH net-next v3 3/5] riscv: dts: spacemit: Add Ethernet support for K1
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 1/5] dt-bindings: net: Add " Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC Vivian Wang
@ 2025-07-02 6:01 ` Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 4/5] riscv: dts: spacemit: Add Ethernet support for BPI-F3 Vivian Wang
` (2 subsequent siblings)
5 siblings, 0 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 6:01 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Vivian Wang, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
Add nodes for each of the two Ethernet MACs on K1 with generic
properties. Also add "gmac" pins to pinctrl config.
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
---
arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi | 48 ++++++++++++++++++++++++++++
arch/riscv/boot/dts/spacemit/k1.dtsi | 22 +++++++++++++
2 files changed, 70 insertions(+)
diff --git a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
index 283663647a86ff137917ced8bfe79a129c86342a..37f3deeaffb987756581a956d634eeb81ac20b1f 100644
--- a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
@@ -11,6 +11,54 @@
#define K1_GPIO(x) (x / 32) (x % 32)
&pinctrl {
+ gmac0_cfg: gmac0-cfg {
+ gmac0-pins {
+ pinmux = <K1_PADCONF(0, 1)>, /* gmac0_rxdv */
+ <K1_PADCONF(1, 1)>, /* gmac0_rx_d0 */
+ <K1_PADCONF(2, 1)>, /* gmac0_rx_d1 */
+ <K1_PADCONF(3, 1)>, /* gmac0_rx_clk */
+ <K1_PADCONF(4, 1)>, /* gmac0_rx_d2 */
+ <K1_PADCONF(5, 1)>, /* gmac0_rx_d3 */
+ <K1_PADCONF(6, 1)>, /* gmac0_tx_d0 */
+ <K1_PADCONF(7, 1)>, /* gmac0_tx_d1 */
+ <K1_PADCONF(8, 1)>, /* gmac0_tx */
+ <K1_PADCONF(9, 1)>, /* gmac0_tx_d2 */
+ <K1_PADCONF(10, 1)>, /* gmac0_tx_d3 */
+ <K1_PADCONF(11, 1)>, /* gmac0_tx_en */
+ <K1_PADCONF(12, 1)>, /* gmac0_mdc */
+ <K1_PADCONF(13, 1)>, /* gmac0_mdio */
+ <K1_PADCONF(14, 1)>, /* gmac0_int_n */
+ <K1_PADCONF(45, 1)>; /* gmac0_clk_ref */
+
+ bias-pull-up = <0>;
+ drive-strength = <21>;
+ };
+ };
+
+ gmac1_cfg: gmac1-cfg {
+ gmac1-pins {
+ pinmux = <K1_PADCONF(29, 1)>, /* gmac1_rxdv */
+ <K1_PADCONF(30, 1)>, /* gmac1_rx_d0 */
+ <K1_PADCONF(31, 1)>, /* gmac1_rx_d1 */
+ <K1_PADCONF(32, 1)>, /* gmac1_rx_clk */
+ <K1_PADCONF(33, 1)>, /* gmac1_rx_d2 */
+ <K1_PADCONF(34, 1)>, /* gmac1_rx_d3 */
+ <K1_PADCONF(35, 1)>, /* gmac1_tx_d0 */
+ <K1_PADCONF(36, 1)>, /* gmac1_tx_d1 */
+ <K1_PADCONF(37, 1)>, /* gmac1_tx */
+ <K1_PADCONF(38, 1)>, /* gmac1_tx_d2 */
+ <K1_PADCONF(39, 1)>, /* gmac1_tx_d3 */
+ <K1_PADCONF(40, 1)>, /* gmac1_tx_en */
+ <K1_PADCONF(41, 1)>, /* gmac1_mdc */
+ <K1_PADCONF(42, 1)>, /* gmac1_mdio */
+ <K1_PADCONF(43, 1)>, /* gmac1_int_n */
+ <K1_PADCONF(46, 1)>; /* gmac1_clk_ref */
+
+ bias-pull-up = <0>;
+ drive-strength = <21>;
+ };
+ };
+
uart0_2_cfg: uart0-2-cfg {
uart0-2-pins {
pinmux = <K1_PADCONF(68, 2)>,
diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
index 937b87c563a6b1e97740286c723aca52207f3f48..ce9cd8854bec8dbe48517b4ce57cee69d4d1d2f5 100644
--- a/arch/riscv/boot/dts/spacemit/k1.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
@@ -625,6 +625,28 @@ network-bus {
#size-cells = <2>;
dma-ranges = <0x0 0x00000000 0x0 0x00000000 0x0 0x80000000>,
<0x0 0x80000000 0x1 0x00000000 0x0 0x80000000>;
+
+ eth0: ethernet@cac80000 {
+ compatible = "spacemit,k1-emac";
+ reg = <0x0 0xcac80000 0x0 0x420>;
+ clocks = <&syscon_apmu CLK_EMAC0_BUS>;
+ interrupts = <131>;
+ mac-address = [ 00 00 00 00 00 00 ];
+ resets = <&syscon_apmu RESET_EMAC0>;
+ spacemit,apmu = <&syscon_apmu 0x3e4>;
+ status = "disabled";
+ };
+
+ eth1: ethernet@cac81000 {
+ compatible = "spacemit,k1-emac";
+ reg = <0x0 0xcac81000 0x0 0x420>;
+ clocks = <&syscon_apmu CLK_EMAC1_BUS>;
+ interrupts = <133>;
+ mac-address = [ 00 00 00 00 00 00 ];
+ resets = <&syscon_apmu RESET_EMAC1>;
+ spacemit,apmu = <&syscon_apmu 0x3ec>;
+ status = "disabled";
+ };
};
pcie-bus {
--
2.49.0
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH net-next v3 4/5] riscv: dts: spacemit: Add Ethernet support for BPI-F3
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
` (2 preceding siblings ...)
2025-07-02 6:01 ` [PATCH net-next v3 3/5] riscv: dts: spacemit: Add Ethernet support for K1 Vivian Wang
@ 2025-07-02 6:01 ` Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter Vivian Wang
2025-07-03 7:23 ` [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Simon Horman
5 siblings, 0 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 6:01 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Vivian Wang, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
Banana Pi BPI-F3 uses an RGMII PHY for each port and uses GPIO for PHY
reset.
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
---
arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 46 +++++++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index fe22c747c5012fe56d42ac8a7efdbbdb694f31b6..15fa4a5ebd043f3fbb115d37e5a980c9b773a228 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -40,6 +40,52 @@ &emmc {
status = "okay";
};
+ð0 {
+ phy-handle = <&rgmii0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_cfg>;
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <0>;
+ status = "okay";
+
+ mdio-bus {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
+ reset-delay-us = <10000>;
+ reset-post-delay-us = <100000>;
+
+ rgmii0: phy@1 {
+ reg = <0x1>;
+ };
+ };
+};
+
+ð1 {
+ phy-handle = <&rgmii1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1_cfg>;
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <250>;
+ status = "okay";
+
+ mdio-bus {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
+ reset-delay-us = <10000>;
+ reset-post-delay-us = <100000>;
+
+ rgmii1: phy@1 {
+ reg = <0x1>;
+ };
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_2_cfg>;
--
2.49.0
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
` (3 preceding siblings ...)
2025-07-02 6:01 ` [PATCH net-next v3 4/5] riscv: dts: spacemit: Add Ethernet support for BPI-F3 Vivian Wang
@ 2025-07-02 6:01 ` Vivian Wang
2025-07-03 6:48 ` Junhui Liu
2025-07-03 7:23 ` [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Simon Horman
5 siblings, 1 reply; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 6:01 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Vivian Wang, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
reset.
Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
---
arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46 +++++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index 4483192141049caa201c093fb206b6134a064f42..c5933555c06b66f40e61fe2b9c159ba0770c2fa1 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -20,6 +20,52 @@ chosen {
};
};
+ð0 {
+ phy-handle = <&rgmii0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_cfg>;
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <0>;
+ status = "okay";
+
+ mdio-bus {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
+ reset-delay-us = <10000>;
+ reset-post-delay-us = <100000>;
+
+ rgmii0: phy@1 {
+ reg = <0x1>;
+ };
+ };
+};
+
+ð1 {
+ phy-handle = <&rgmii1>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1_cfg>;
+ rx-internal-delay-ps = <0>;
+ tx-internal-delay-ps = <250>;
+ status = "okay";
+
+ mdio-bus {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
+ reset-delay-us = <10000>;
+ reset-post-delay-us = <100000>;
+
+ rgmii1: phy@1 {
+ reg = <0x1>;
+ };
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_2_cfg>;
--
2.49.0
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC
2025-07-02 6:01 ` [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC Vivian Wang
@ 2025-07-02 7:17 ` Maxime Chevallier
2025-07-02 7:41 ` Vivian Wang
2025-07-03 7:19 ` Simon Horman
1 sibling, 1 reply; 15+ messages in thread
From: Maxime Chevallier @ 2025-07-02 7:17 UTC (permalink / raw)
To: Vivian Wang
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Philipp Zabel, Paul Walmsley, Palmer Dabbelt,
Albert Ou, Alexandre Ghiti, Vivian Wang, Lukas Bulwahn,
Geert Uytterhoeven, Parthiban Veerasooran, netdev, devicetree,
linux-riscv, spacemit, linux-kernel
Hello Vivian,
On Wed, 02 Jul 2025 14:01:41 +0800
Vivian Wang <wangruikang@iscas.ac.cn> wrote:
> The Ethernet MACs found on SpacemiT K1 appears to be a custom design
> that only superficially resembles some other embedded MACs. SpacemiT
> refers to them as "EMAC", so let's just call the driver "k1_emac".
>
> This driver is based on "k1x-emac" in the same directory in the vendor's
> tree [1]. Some debugging tunables have been fixed to vendor-recommended
> defaults, and PTP support is not included yet.
>
> [1]: https://github.com/spacemit-com/linux-k1x
>
> Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
I have a handful of tiny comments, the rest looks fine by me !
> +static int emac_phy_connect(struct net_device *ndev)
> +{
> + struct emac_priv *priv = netdev_priv(ndev);
> + struct device *dev = &priv->pdev->dev;
> + struct phy_device *phydev;
> + struct device_node *np;
> + int ret;
> +
> + ret = of_get_phy_mode(dev->of_node, &priv->phy_interface);
> + if (ret) {
> + dev_err(dev, "No phy-mode found");
> + return ret;
> + }
> +
> + np = of_parse_phandle(dev->of_node, "phy-handle", 0);
> + if (!np && of_phy_is_fixed_link(dev->of_node))
> + np = of_node_get(dev->of_node);
> +
> + if (!np) {
> + dev_err(dev, "No PHY specified");
> + return -ENODEV;
> + }
> +
> + ret = emac_phy_interface_config(priv);
> + if (ret)
> + goto err_node_put;
> +
> + phydev = of_phy_connect(ndev, np, &emac_adjust_link, 0,
> + priv->phy_interface);
> + if (!phydev) {
> + dev_err(dev, "Could not attach to PHY\n");
> + ret = -ENODEV;
> + goto err_node_put;
> + }
> +
> + phydev->mac_managed_pm = true;
> +
> + ndev->phydev = phydev;
of_phy_connect() eventually calls phy_attach_direct(), which sets
ndev->phydev, so you don't need to do it here :)
> +
> + emac_update_delay_line(priv);
> +
> +err_node_put:
> + of_node_put(np);
> + return ret;
> +}
[ ... ]
> +static int emac_down(struct emac_priv *priv)
> +{
> + struct platform_device *pdev = priv->pdev;
> + struct net_device *ndev = priv->ndev;
> +
> + netif_stop_queue(ndev);
> +
> + phy_stop(ndev->phydev);
phy_disconnect() will call phy_stop() for you, you can remove it.
> + phy_disconnect(ndev->phydev);
> +
> + emac_wr(priv, MAC_INTERRUPT_ENABLE, 0x0);
> + emac_wr(priv, DMA_INTERRUPT_ENABLE, 0x0);
> +
> + free_irq(priv->irq, ndev);
> +
> + napi_disable(&priv->napi);
> +
> + emac_reset_hw(priv);
> +
> + pm_runtime_put_sync(&pdev->dev);
> + return 0;
> +}
> +
[ ... ]
> +static int emac_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct reset_control *reset;
> + struct net_device *ndev;
> + struct emac_priv *priv;
> + int ret;
> +
> + ndev = devm_alloc_etherdev(dev, sizeof(struct emac_priv));
> + if (!ndev)
> + return -ENOMEM;
> +
> + ndev->hw_features = NETIF_F_SG;
> + ndev->features |= ndev->hw_features;
> +
> + ndev->min_mtu = ETH_MIN_MTU;
This should already be the default value when using
devm_alloc_etherdev()
> + ndev->max_mtu = EMAC_RX_BUF_4K - (ETH_HLEN + ETH_FCS_LEN);
> +
> + priv = netdev_priv(ndev);
> + priv->ndev = ndev;
> + priv->pdev = pdev;
> + platform_set_drvdata(pdev, priv);
> + priv->hw_stats = devm_kzalloc(dev, sizeof(*priv->hw_stats), GFP_KERNEL);
> + if (!priv->hw_stats) {
> + dev_err(dev, "Failed to allocate memory for stats\n");
> + ret = -ENOMEM;
> + goto err;
> + }
> +
> + ret = emac_config_dt(pdev, priv);
> + if (ret < 0) {
> + dev_err(dev, "Configuration failed\n");
> + goto err;
> + }
> +
> + ndev->watchdog_timeo = 5 * HZ;
> + ndev->base_addr = (unsigned long)priv->iobase;
> + ndev->irq = priv->irq;
> +
> + ndev->ethtool_ops = &emac_ethtool_ops;
> + ndev->netdev_ops = &emac_netdev_ops;
> +
> + devm_pm_runtime_enable(&pdev->dev);
> +
> + priv->bus_clk = devm_clk_get_enabled(&pdev->dev, NULL);
> + if (IS_ERR(priv->bus_clk)) {
> + ret = dev_err_probe(dev, PTR_ERR(priv->bus_clk),
> + "Failed to get clock\n");
> + goto err;
> + }
> +
> + reset = devm_reset_control_get_optional_exclusive_deasserted(&pdev->dev,
> + NULL);
> + if (IS_ERR(reset)) {
> + ret = dev_err_probe(dev, PTR_ERR(reset),
> + "Failed to get reset\n");
> + goto err;
> + }
> +
> + emac_sw_init(priv);
> +
> + if (of_phy_is_fixed_link(dev->of_node)) {
> + ret = of_phy_register_fixed_link(dev->of_node);
> + if (ret) {
> + dev_err_probe(dev, ret,
> + "Failed to register fixed-link");
> + goto err_timer_delete;
> + }
It looks like you're missing the calls to:
of_phy_deregister_fixed_link()
in the error path here as well as in the .remove() function.
> + }
> +
> + ret = emac_mdio_init(priv);
> + if (ret)
> + goto err_timer_delete;
> +
> + SET_NETDEV_DEV(ndev, &pdev->dev);
> +
> + ret = devm_register_netdev(dev, ndev);
> + if (ret) {
> + dev_err(dev, "devm_register_netdev failed\n");
> + goto err_timer_delete;
> + }
> +
> + netif_napi_add(ndev, &priv->napi, emac_rx_poll);
> + netif_carrier_off(ndev);
> +
> + return 0;
> +
> +err_timer_delete:
> + timer_delete_sync(&priv->txtimer);
> +err:
> + return ret;
> +}
Maxime
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC
2025-07-02 7:17 ` Maxime Chevallier
@ 2025-07-02 7:41 ` Vivian Wang
0 siblings, 0 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-02 7:41 UTC (permalink / raw)
To: Maxime Chevallier
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Philipp Zabel, Paul Walmsley, Palmer Dabbelt,
Albert Ou, Alexandre Ghiti, Vivian Wang, Lukas Bulwahn,
Geert Uytterhoeven, Parthiban Veerasooran, netdev, devicetree,
linux-riscv, spacemit, linux-kernel
Hi Maxime,
Thanks for your suggestions.
On 7/2/25 15:17, Maxime Chevallier wrote:
> Hello Vivian,
>
> On Wed, 02 Jul 2025 14:01:41 +0800
> Vivian Wang <wangruikang@iscas.ac.cn> wrote:
>
>> The Ethernet MACs found on SpacemiT K1 appears to be a custom design
>> that only superficially resembles some other embedded MACs. SpacemiT
>> refers to them as "EMAC", so let's just call the driver "k1_emac".
>>
>> This driver is based on "k1x-emac" in the same directory in the vendor's
>> tree [1]. Some debugging tunables have been fixed to vendor-recommended
>> defaults, and PTP support is not included yet.
>>
>> [1]: https://github.com/spacemit-com/linux-k1x
>>
>> Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
> I have a handful of tiny comments, the rest looks fine by me !
>
>> +static int emac_phy_connect(struct net_device *ndev)
>> +{
>> + struct emac_priv *priv = netdev_priv(ndev);
>> + struct device *dev = &priv->pdev->dev;
>> + struct phy_device *phydev;
>> + struct device_node *np;
>> + int ret;
>> +
>> + ret = of_get_phy_mode(dev->of_node, &priv->phy_interface);
>> + if (ret) {
>> + dev_err(dev, "No phy-mode found");
>> + return ret;
>> + }
>> +
>> + np = of_parse_phandle(dev->of_node, "phy-handle", 0);
>> + if (!np && of_phy_is_fixed_link(dev->of_node))
>> + np = of_node_get(dev->of_node);
>> +
>> + if (!np) {
>> + dev_err(dev, "No PHY specified");
>> + return -ENODEV;
>> + }
>> +
>> + ret = emac_phy_interface_config(priv);
>> + if (ret)
>> + goto err_node_put;
>> +
>> + phydev = of_phy_connect(ndev, np, &emac_adjust_link, 0,
>> + priv->phy_interface);
>> + if (!phydev) {
>> + dev_err(dev, "Could not attach to PHY\n");
>> + ret = -ENODEV;
>> + goto err_node_put;
>> + }
>> +
>> + phydev->mac_managed_pm = true;
>> +
>> + ndev->phydev = phydev;
> of_phy_connect() eventually calls phy_attach_direct(), which sets
> ndev->phydev, so you don't need to do it here :)
I will remove it next version.
>> +
>> + emac_update_delay_line(priv);
>> +
>> +err_node_put:
>> + of_node_put(np);
>> + return ret;
>> +}
> [ ... ]
>
>> +static int emac_down(struct emac_priv *priv)
>> +{
>> + struct platform_device *pdev = priv->pdev;
>> + struct net_device *ndev = priv->ndev;
>> +
>> + netif_stop_queue(ndev);
>> +
>> + phy_stop(ndev->phydev);
> phy_disconnect() will call phy_stop() for you, you can remove it.
Thanks, I will simplify handling of this.
>> + phy_disconnect(ndev->phydev);
>> +
>> + emac_wr(priv, MAC_INTERRUPT_ENABLE, 0x0);
>> + emac_wr(priv, DMA_INTERRUPT_ENABLE, 0x0);
>> +
>> + free_irq(priv->irq, ndev);
>> +
>> + napi_disable(&priv->napi);
>> +
>> + emac_reset_hw(priv);
>> +
>> + pm_runtime_put_sync(&pdev->dev);
>> + return 0;
>> +}
>> +
> [ ... ]
>
>> +static int emac_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct reset_control *reset;
>> + struct net_device *ndev;
>> + struct emac_priv *priv;
>> + int ret;
>> +
>> + ndev = devm_alloc_etherdev(dev, sizeof(struct emac_priv));
>> + if (!ndev)
>> + return -ENOMEM;
>> +
>> + ndev->hw_features = NETIF_F_SG;
>> + ndev->features |= ndev->hw_features;
>> +
>> + ndev->min_mtu = ETH_MIN_MTU;
> This should already be the default value when using
> devm_alloc_etherdev()
I will remove next version.
>> + ndev->max_mtu = EMAC_RX_BUF_4K - (ETH_HLEN + ETH_FCS_LEN);
>> +
>> + priv = netdev_priv(ndev);
>> + priv->ndev = ndev;
>> + priv->pdev = pdev;
>> + platform_set_drvdata(pdev, priv);
>> + priv->hw_stats = devm_kzalloc(dev, sizeof(*priv->hw_stats), GFP_KERNEL);
>> + if (!priv->hw_stats) {
>> + dev_err(dev, "Failed to allocate memory for stats\n");
>> + ret = -ENOMEM;
>> + goto err;
>> + }
>> +
>> + ret = emac_config_dt(pdev, priv);
>> + if (ret < 0) {
>> + dev_err(dev, "Configuration failed\n");
>> + goto err;
>> + }
>> +
>> + ndev->watchdog_timeo = 5 * HZ;
>> + ndev->base_addr = (unsigned long)priv->iobase;
>> + ndev->irq = priv->irq;
>> +
>> + ndev->ethtool_ops = &emac_ethtool_ops;
>> + ndev->netdev_ops = &emac_netdev_ops;
>> +
>> + devm_pm_runtime_enable(&pdev->dev);
>> +
>> + priv->bus_clk = devm_clk_get_enabled(&pdev->dev, NULL);
>> + if (IS_ERR(priv->bus_clk)) {
>> + ret = dev_err_probe(dev, PTR_ERR(priv->bus_clk),
>> + "Failed to get clock\n");
>> + goto err;
>> + }
>> +
>> + reset = devm_reset_control_get_optional_exclusive_deasserted(&pdev->dev,
>> + NULL);
>> + if (IS_ERR(reset)) {
>> + ret = dev_err_probe(dev, PTR_ERR(reset),
>> + "Failed to get reset\n");
>> + goto err;
>> + }
>> +
>> + emac_sw_init(priv);
>> +
>> + if (of_phy_is_fixed_link(dev->of_node)) {
>> + ret = of_phy_register_fixed_link(dev->of_node);
>> + if (ret) {
>> + dev_err_probe(dev, ret,
>> + "Failed to register fixed-link");
>> + goto err_timer_delete;
>> + }
> It looks like you're missing the calls to:
>
> of_phy_deregister_fixed_link()
>
> in the error path here as well as in the .remove() function.
It seems I had misunderstood the use of of_phy_register_fixed_link, I
will fix this next version.
Thanks,
Vivian "dramforever" Wang
>> + }
>> +
>> + ret = emac_mdio_init(priv);
>> + if (ret)
>> + goto err_timer_delete;
>> +
>> + SET_NETDEV_DEV(ndev, &pdev->dev);
>> +
>> + ret = devm_register_netdev(dev, ndev);
>> + if (ret) {
>> + dev_err(dev, "devm_register_netdev failed\n");
>> + goto err_timer_delete;
>> + }
>> +
>> + netif_napi_add(ndev, &priv->napi, emac_rx_poll);
>> + netif_carrier_off(ndev);
>> +
>> + return 0;
>> +
>> +err_timer_delete:
>> + timer_delete_sync(&priv->txtimer);
>> +err:
>> + return ret;
>> +}
> Maxime
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter
2025-07-02 6:01 ` [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter Vivian Wang
@ 2025-07-03 6:48 ` Junhui Liu
2025-07-03 7:46 ` Vivian Wang
0 siblings, 1 reply; 15+ messages in thread
From: Junhui Liu @ 2025-07-03 6:48 UTC (permalink / raw)
To: Vivian Wang, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Yixun Lan, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
Hi Vivian,
Thanks for you work!
On 2025/7/2 14:01, Vivian Wang wrote:
> Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
> reset.
>
> Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
Successfully tested with iperf3 on Milk-V Jupiter.
TCP Rx: 941 Mbits/sec
TCP Tx: 943 Mbits/sec
UDP Rx: 956 Mbits/sec
UDP Tx: 956 Mbits/sec
Tested-by: Junhui Liu <junhui.liu@pigmoral.tech>
> ---
> arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46 +++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> index 4483192141049caa201c093fb206b6134a064f42..c5933555c06b66f40e61fe2b9c159ba0770c2fa1 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> @@ -20,6 +20,52 @@ chosen {
> };
> };
>
> +ð0 {
> + phy-handle = <&rgmii0>;
> + phy-mode = "rgmii-id";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac0_cfg>;
> + rx-internal-delay-ps = <0>;
> + tx-internal-delay-ps = <0>;
> + status = "okay";
> +
> + mdio-bus {
> + #address-cells = <0x1>;
> + #size-cells = <0x0>;
> +
> + reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
> + reset-delay-us = <10000>;
> + reset-post-delay-us = <100000>;
> +
> + rgmii0: phy@1 {
> + reg = <0x1>;
> + };
> + };
> +};
> +
> +ð1 {
> + phy-handle = <&rgmii1>;
> + phy-mode = "rgmii-id";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac1_cfg>;
> + rx-internal-delay-ps = <0>;
> + tx-internal-delay-ps = <250>;
> + status = "okay";
> +
> + mdio-bus {
> + #address-cells = <0x1>;
> + #size-cells = <0x0>;
> +
> + reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
> + reset-delay-us = <10000>;
> + reset-post-delay-us = <100000>;
> +
> + rgmii1: phy@1 {
> + reg = <0x1>;
> + };
> + };
> +};
> +
> &uart0 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart0_2_cfg>;
>
--
Best regards,
Junhui Liu
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC
2025-07-02 6:01 ` [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC Vivian Wang
2025-07-02 7:17 ` Maxime Chevallier
@ 2025-07-03 7:19 ` Simon Horman
2025-07-03 7:58 ` Vivian Wang
1 sibling, 1 reply; 15+ messages in thread
From: Simon Horman @ 2025-07-03 7:19 UTC (permalink / raw)
To: Vivian Wang
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Philipp Zabel, Paul Walmsley, Palmer Dabbelt,
Albert Ou, Alexandre Ghiti, Vivian Wang, Lukas Bulwahn,
Geert Uytterhoeven, Parthiban Veerasooran, netdev, devicetree,
linux-riscv, spacemit, linux-kernel
On Wed, Jul 02, 2025 at 02:01:41PM +0800, Vivian Wang wrote:
...
> diff --git a/drivers/net/ethernet/spacemit/k1_emac.c b/drivers/net/ethernet/spacemit/k1_emac.c
...
> +static int emac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
> +{
> + struct emac_priv *priv = netdev_priv(ndev);
> + int nfrags = skb_shinfo(skb)->nr_frags;
> + struct device *dev = &priv->pdev->dev;
> +
> + if (unlikely(emac_tx_avail(priv) < nfrags + 1)) {
> + if (!netif_queue_stopped(ndev)) {
> + netif_stop_queue(ndev);
> + dev_err_ratelimited(dev, "TX ring full, stop TX queue\n");
> + }
> + return NETDEV_TX_BUSY;
> + }
> +
> + emac_tx_mem_map(priv, skb);
> +
> + ndev->stats.tx_packets++;
> + ndev->stats.tx_bytes += skb->len;
> +
> + /* Make sure there is space in the ring for the next TX. */
> + if (unlikely(emac_tx_avail(priv) <= MAX_SKB_FRAGS + 2))
> + netif_stop_queue(ndev);
> +
> + return NETDEV_TX_OK;
> +}
> +
> +static u32 emac_tx_read_stat_cnt(struct emac_priv *priv, u8 cnt)
> +{
> + u32 val, tmp;
> + int ret;
> +
> + val = 0x8000 | cnt;
> + emac_wr(priv, MAC_TX_STATCTR_CONTROL, val);
> + val = emac_rd(priv, MAC_TX_STATCTR_CONTROL);
> +
> + ret = readl_poll_timeout_atomic(priv->iobase + MAC_TX_STATCTR_CONTROL,
> + val, !(val & 0x8000), 100, 10000);
> +
> + if (ret) {
> + netdev_err(priv->ndev, "read TX stat timeout\n");
> + return ret;
> + }
> +
> + tmp = emac_rd(priv, MAC_TX_STATCTR_DATA_HIGH);
> + val = tmp << 16;
> + tmp = emac_rd(priv, MAC_TX_STATCTR_DATA_LOW);
> + val |= tmp;
> +
> + return val;
> +}
> +
> +static u32 emac_rx_read_stat_cnt(struct emac_priv *priv, u8 cnt)
> +{
> + u32 val, tmp;
> + int ret;
> +
> + val = 0x8000 | cnt;
> + emac_wr(priv, MAC_RX_STATCTR_CONTROL, val);
> + val = emac_rd(priv, MAC_RX_STATCTR_CONTROL);
> +
> + ret = readl_poll_timeout_atomic(priv->iobase + MAC_RX_STATCTR_CONTROL,
> + val, !(val & 0x8000), 100, 10000);
> +
> + if (ret) {
> + netdev_err(priv->ndev, "read RX stat timeout\n");
> + return ret;
> + }
> +
> + tmp = emac_rd(priv, MAC_RX_STATCTR_DATA_HIGH);
> + val = tmp << 16;
> + tmp = emac_rd(priv, MAC_RX_STATCTR_DATA_LOW);
> + val |= tmp;
> +
> + return val;
> +}
> +
> +static int emac_set_mac_address(struct net_device *ndev, void *addr)
> +{
> + struct emac_priv *priv = netdev_priv(ndev);
> + int ret = eth_mac_addr(ndev, addr);
> +
> + if (ret)
> + return ret;
> +
> + /* If running, set now; if not running it will be set in emac_up. */
> + if (netif_running(ndev))
> + emac_set_mac_addr(priv, ndev->dev_addr);
> +
> + return 0;
> +}
> +
> +static void emac_mac_multicast_filter_clear(struct emac_priv *priv)
> +{
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0x0);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0x0);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0x0);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0x0);
> +}
> +
> +/* Configure Multicast and Promiscuous modes */
> +static void emac_rx_mode_set(struct net_device *ndev)
> +{
> + struct emac_priv *priv = netdev_priv(ndev);
> + u32 crc32, bit, reg, hash, val;
> + struct netdev_hw_addr *ha;
> + u32 mc_filter[4] = { 0 };
> +
> + val = emac_rd(priv, MAC_ADDRESS_CONTROL);
> +
> + val &= ~MREGBIT_PROMISCUOUS_MODE;
> +
> + if (ndev->flags & IFF_PROMISC) {
> + /* Enable promisc mode */
> + val |= MREGBIT_PROMISCUOUS_MODE;
> + } else if ((ndev->flags & IFF_ALLMULTI) ||
> + (netdev_mc_count(ndev) > HASH_TABLE_SIZE)) {
> + /* Accept all multicast frames by setting every bit */
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0xffff);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0xffff);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0xffff);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0xffff);
> + } else if (!netdev_mc_empty(ndev)) {
> + emac_mac_multicast_filter_clear(priv);
> + netdev_for_each_mc_addr(ha, ndev) {
> + /* Calculate the CRC of the MAC address */
> + crc32 = ether_crc(ETH_ALEN, ha->addr);
> +
> + /*
> + * The hash table is an array of 4 16-bit registers. It
> + * is treated like an array of 64 bits (bits[hash]). Use
> + * the upper 6 bits of the above CRC as the hash value.
> + */
> + hash = (crc32 >> 26) & 0x3F;
> + reg = hash / 16;
> + bit = hash % 16;
> + mc_filter[reg] |= BIT(bit);
> + }
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, mc_filter[0]);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, mc_filter[1]);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, mc_filter[2]);
> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, mc_filter[3]);
> + }
> +
> + emac_wr(priv, MAC_ADDRESS_CONTROL, val);
> +}
> +
> +static int emac_change_mtu(struct net_device *ndev, int mtu)
> +{
> + struct emac_priv *priv = netdev_priv(ndev);
> + u32 frame_len;
> +
> + if (netif_running(ndev)) {
> + netdev_err(ndev, "must be stopped to change MTU\n");
> + return -EBUSY;
> + }
> +
> + frame_len = mtu + ETH_HLEN + ETH_FCS_LEN;
> +
> + if (frame_len <= EMAC_DEFAULT_BUFSIZE)
> + priv->dma_buf_sz = EMAC_DEFAULT_BUFSIZE;
> + else if (frame_len <= EMAC_RX_BUF_2K)
> + priv->dma_buf_sz = EMAC_RX_BUF_2K;
> + else
> + priv->dma_buf_sz = EMAC_RX_BUF_4K;
> +
> + ndev->mtu = mtu;
> +
> + return 0;
> +}
> +
> +static void emac_tx_timeout(struct net_device *ndev, unsigned int txqueue)
> +{
> + struct emac_priv *priv = netdev_priv(ndev);
> +
> + schedule_work(&priv->tx_timeout_task);
> +}
> +
> +static int emac_mii_read(struct mii_bus *bus, int phy_addr, int regnum)
> +{
> + struct emac_priv *priv = bus->priv;
> + u32 cmd = 0, val;
> + int ret;
> +
> + cmd |= phy_addr & 0x1F;
> + cmd |= (regnum & 0x1F) << 5;
> + cmd |= MREGBIT_START_MDIO_TRANS | MREGBIT_MDIO_READ_WRITE;
> +
> + emac_wr(priv, MAC_MDIO_DATA, 0x0);
> + emac_wr(priv, MAC_MDIO_CONTROL, cmd);
> +
> + ret = readl_poll_timeout(priv->iobase + MAC_MDIO_CONTROL, val,
> + !((val >> 15) & 0x1), 100, 10000);
> +
> + if (ret)
> + return ret;
> +
> + val = emac_rd(priv, MAC_MDIO_DATA);
> + return val;
> +}
> +
> +static int emac_mii_write(struct mii_bus *bus, int phy_addr, int regnum,
> + u16 value)
> +{
> + struct emac_priv *priv = bus->priv;
> + u32 cmd = 0, val;
> + int ret;
> +
> + emac_wr(priv, MAC_MDIO_DATA, value);
> +
> + cmd |= phy_addr & 0x1F;
> + cmd |= (regnum & 0x1F) << 5;
> + cmd |= MREGBIT_START_MDIO_TRANS;
> +
> + emac_wr(priv, MAC_MDIO_CONTROL, cmd);
> +
> + ret = readl_poll_timeout(priv->iobase + MAC_MDIO_CONTROL, val,
> + !((val >> 15) & 0x1), 100, 10000);
> +
> + return ret;
> +}
> +
> +static int emac_mdio_init(struct emac_priv *priv)
> +{
> + struct device *dev = &priv->pdev->dev;
> + struct device_node *mii_np;
> + struct mii_bus *mii;
> + int ret;
> +
> + mii = devm_mdiobus_alloc(dev);
> + if (!mii)
> + return -ENOMEM;
> +
> + mii->priv = priv;
> + mii->name = "k1_emac_mii";
> + mii->read = emac_mii_read;
> + mii->write = emac_mii_write;
> + mii->parent = dev;
> + mii->phy_mask = 0xffffffff;
> + snprintf(mii->id, MII_BUS_ID_SIZE, "%s", priv->pdev->name);
> +
> + mii_np = of_get_available_child_by_name(dev->of_node, "mdio-bus");
> +
> + ret = devm_of_mdiobus_register(dev, mii, mii_np);
> + if (ret)
> + dev_err_probe(dev, ret, "Failed to register mdio bus\n");
> +
> + of_node_put(mii_np);
> + return ret;
> +}
> +
> +static void emac_get_strings(struct net_device *dev, u32 stringset, u8 *data)
> +{
> + int i;
> +
> + switch (stringset) {
> + case ETH_SS_STATS:
> + for (i = 0; i < ARRAY_SIZE(emac_ethtool_stats); i++) {
> + memcpy(data, emac_ethtool_stats[i].str,
> + ETH_GSTRING_LEN);
> + data += ETH_GSTRING_LEN;
> + }
> + break;
> + }
> +}
> +
> +static int emac_get_sset_count(struct net_device *dev, int sset)
> +{
> + switch (sset) {
> + case ETH_SS_STATS:
> + return ARRAY_SIZE(emac_ethtool_stats);
> + default:
> + return -EOPNOTSUPP;
> + }
> +}
> +
> +static void emac_stats_update(struct emac_priv *priv)
> +{
> + struct emac_hw_stats *hwstats = priv->hw_stats;
> + u32 *stats = (u32 *)hwstats;
> + int i;
> +
> + for (i = 0; i < EMAC_TX_STATS_NUM; i++)
> + stats[i] = emac_tx_read_stat_cnt(priv, i);
> +
> + for (i = 0; i < EMAC_RX_STATS_NUM; i++)
> + stats[i + EMAC_TX_STATS_NUM] = emac_rx_read_stat_cnt(priv, i);
> +}
> +
> +static void emac_get_ethtool_stats(struct net_device *dev,
> + struct ethtool_stats *stats, u64 *data)
> +{
> + struct emac_priv *priv = netdev_priv(dev);
> + struct emac_hw_stats *hwstats;
> + unsigned long flags;
> + u32 *data_src;
> + u64 *data_dst;
> + int i;
> +
> + hwstats = priv->hw_stats;
> +
> + if (netif_running(dev) && netif_device_present(dev)) {
> + if (spin_trylock_irqsave(&priv->stats_lock, flags)) {
> + emac_stats_update(priv);
> + spin_unlock_irqrestore(&priv->stats_lock, flags);
> + }
> + }
> +
> + data_dst = data;
> +
> + for (i = 0; i < ARRAY_SIZE(emac_ethtool_stats); i++) {
> + data_src = (u32 *)hwstats + emac_ethtool_stats[i].offset;
> + *data_dst++ = (u64)(*data_src);
> + }
> +}
> +
> +static int emac_ethtool_get_regs_len(struct net_device *dev)
> +{
> + return (EMAC_DMA_REG_CNT + EMAC_MAC_REG_CNT) * sizeof(u32);
> +}
> +
> +static void emac_ethtool_get_regs(struct net_device *dev,
> + struct ethtool_regs *regs, void *space)
> +{
> + struct emac_priv *priv = netdev_priv(dev);
> + u32 *reg_space = space;
> + int i;
> +
> + regs->version = 1;
> +
> + for (i = 0; i < EMAC_DMA_REG_CNT; i++)
> + reg_space[i] = emac_rd(priv, DMA_CONFIGURATION + i * 4);
> +
> + for (i = 0; i < EMAC_MAC_REG_CNT; i++)
> + reg_space[i + EMAC_DMA_REG_CNT] =
> + emac_rd(priv, MAC_GLOBAL_CONTROL + i * 4);
> +}
> +
> +static void emac_get_drvinfo(struct net_device *dev,
> + struct ethtool_drvinfo *info)
> +{
> + strscpy(info->driver, DRIVER_NAME, sizeof(info->driver));
> + info->n_stats = ARRAY_SIZE(emac_ethtool_stats);
> +}
> +
> +static void emac_tx_timeout_task(struct work_struct *work)
> +{
> + struct net_device *ndev;
> + struct emac_priv *priv;
> +
> + priv = container_of(work, struct emac_priv, tx_timeout_task);
> + ndev = priv->ndev;
> +
> + rtnl_lock();
> +
> + /* No need to reset if already down */
> + if (!netif_running(ndev)) {
> + rtnl_unlock();
> + return;
> + }
> +
> + netdev_err(ndev, "MAC reset due to TX timeout\n");
> +
> + netif_trans_update(ndev); /* prevent tx timeout */
> + dev_close(ndev);
> + dev_open(ndev, NULL);
> +
> + rtnl_unlock();
> +}
> +
> +static void emac_sw_init(struct emac_priv *priv)
> +{
> + priv->dma_buf_sz = EMAC_DEFAULT_BUFSIZE;
> +
> + priv->tx_ring.total_cnt = DEFAULT_TX_RING_NUM;
> + priv->rx_ring.total_cnt = DEFAULT_RX_RING_NUM;
> +
> + spin_lock_init(&priv->stats_lock);
> +
> + INIT_WORK(&priv->tx_timeout_task, emac_tx_timeout_task);
> +
> + priv->tx_coal_frames = EMAC_TX_FRAMES;
> + priv->tx_coal_timeout = EMAC_TX_COAL_TIMEOUT;
> +
> + timer_setup(&priv->txtimer, emac_tx_coal_timer, 0);
> +}
> +
...
> +static irqreturn_t emac_interrupt_handler(int irq, void *dev_id)
> +{
> + struct net_device *ndev = (struct net_device *)dev_id;
> + struct emac_priv *priv = netdev_priv(ndev);
> + bool should_schedule = false;
> + u32 status;
> + u32 clr = 0;
nit: Reverse xmas tree - longest line to shortest - for
these local variable declarations please.
Edward Cree's tool can be helpful here:
https://github.com/ecree-solarflare/xmastree/commits/master/
...
> +static const struct net_device_ops emac_netdev_ops = {
> + .ndo_open = emac_open,
> + .ndo_stop = emac_close,
> + .ndo_start_xmit = emac_start_xmit,
I think that of emac_start_xmit should return netdev_tx_t rather than int
to match the type of the .ndo_start_xmit member of this structure.
Flagged by Clang 20.1.7 [-Wincompatible-function-pointer-types-strict]
> + .ndo_set_mac_address = emac_set_mac_address,
> + .ndo_eth_ioctl = phy_do_ioctl_running,
> + .ndo_change_mtu = emac_change_mtu,
> + .ndo_tx_timeout = emac_tx_timeout,
> + .ndo_set_rx_mode = emac_rx_mode_set,
> +};
...
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
` (4 preceding siblings ...)
2025-07-02 6:01 ` [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter Vivian Wang
@ 2025-07-03 7:23 ` Simon Horman
2025-07-03 7:39 ` Vivian Wang
5 siblings, 1 reply; 15+ messages in thread
From: Simon Horman @ 2025-07-03 7:23 UTC (permalink / raw)
To: Vivian Wang
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Philipp Zabel, Paul Walmsley, Palmer Dabbelt,
Albert Ou, Alexandre Ghiti, Vivian Wang, Lukas Bulwahn,
Geert Uytterhoeven, Parthiban Veerasooran, netdev, devicetree,
linux-riscv, spacemit, linux-kernel, Conor Dooley
On Wed, Jul 02, 2025 at 02:01:39PM +0800, Vivian Wang wrote:
> SpacemiT K1 has two gigabit Ethernet MACs with RGMII and RMII support.
> Add a driver for them, as well as the supporting devicetree and bindings
> updates.
>
> Tested on BananaPi BPI-F3 and Milk-V Jupiter.
>
> I would like to note that even though some bit field names superficially
> resemble that of DesignWare MAC, all other differences point to it in
> fact being a custom design.
>
> Based on SpacemiT drivers [1].
>
> This series depends on reset controller support [2] and DMA buses [3]
> for K1. There are some minor conflicts resulting from both touching
> k1.dtsi, but it should just both be adding nodes.
>
> These patches can also be pulled from:
>
> https://github.com/dramforever/linux/tree/k1/ethernet/v3
>
> [1]: https://github.com/spacemit-com/linux-k1x
> [2]: https://lore.kernel.org/all/20250613011139.1201702-1-elder@riscstar.com
> [3]: https://lore.kernel.org/all/20250623-k1-dma-buses-rfc-wip-v1-0-c0144082061f@iscas.ac.cn
>
> ---
> Changes in v3:
> - Refactored and simplified emac_tx_mem_map
> - Addressed other minor v2 review comments
> - Removed what was patch 3 in v2, depend on DMA buses instead
> - DT nodes in alphabetical order where appropriate
> - Link to v2: https://lore.kernel.org/r/20250618-net-k1-emac-v2-0-94f5f07227a8@iscas.ac.cn
>
> Changes in v2:
> - dts: Put eth0 and eth1 nodes under a bus with dma-ranges
> - dts: Added Milk-V Jupiter
> - Fix typo in emac_init_hw() that broke the driver (Oops!)
> - Reformatted line lengths to under 80
> - Addressed other v1 review comments
> - Link to v1: https://lore.kernel.org/r/20250613-net-k1-emac-v1-0-cc6f9e510667@iscas.ac.cn
>
> ---
> Vivian Wang (5):
> dt-bindings: net: Add support for SpacemiT K1
> net: spacemit: Add K1 Ethernet MAC
> riscv: dts: spacemit: Add Ethernet support for K1
> riscv: dts: spacemit: Add Ethernet support for BPI-F3
> riscv: dts: spacemit: Add Ethernet support for Jupiter
I'm unsure on the plan for merging this. But it seems to me that the first
two patches ought to go though net-next. But in order for patches to
proceed through net-next the entire series ought to apply on that tree - so
CI can run.
I'm not sure on the way forward. But perhaps splitting the series in two:
the first two patches for net-next; and, the riscv patches targeted elsewhere
makes sense?
</2c>
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1
2025-07-03 7:23 ` [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Simon Horman
@ 2025-07-03 7:39 ` Vivian Wang
0 siblings, 0 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-03 7:39 UTC (permalink / raw)
To: Simon Horman
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Philipp Zabel, Paul Walmsley, Palmer Dabbelt,
Albert Ou, Alexandre Ghiti, Vivian Wang, Lukas Bulwahn,
Geert Uytterhoeven, Parthiban Veerasooran, netdev, devicetree,
linux-riscv, spacemit, linux-kernel, Conor Dooley
Hi Simon,
On 7/3/25 15:23, Simon Horman wrote:
> On Wed, Jul 02, 2025 at 02:01:39PM +0800, Vivian Wang wrote:
>> SpacemiT K1 has two gigabit Ethernet MACs with RGMII and RMII support.
>> Add a driver for them, as well as the supporting devicetree and bindings
>> updates.
>>
>> Tested on BananaPi BPI-F3 and Milk-V Jupiter.
>>
>> I would like to note that even though some bit field names superficially
>> resemble that of DesignWare MAC, all other differences point to it in
>> fact being a custom design.
>>
>> Based on SpacemiT drivers [1].
>>
>> This series depends on reset controller support [2] and DMA buses [3]
>> for K1. There are some minor conflicts resulting from both touching
>> k1.dtsi, but it should just both be adding nodes.
>>
>> These patches can also be pulled from:
>>
>> https://github.com/dramforever/linux/tree/k1/ethernet/v3
>>
>> [1]: https://github.com/spacemit-com/linux-k1x
>> [2]: https://lore.kernel.org/all/20250613011139.1201702-1-elder@riscstar.com
>> [3]: https://lore.kernel.org/all/20250623-k1-dma-buses-rfc-wip-v1-0-c0144082061f@iscas.ac.cn
>>
>> ---
>> Changes in v3:
>> - Refactored and simplified emac_tx_mem_map
>> - Addressed other minor v2 review comments
>> - Removed what was patch 3 in v2, depend on DMA buses instead
>> - DT nodes in alphabetical order where appropriate
>> - Link to v2: https://lore.kernel.org/r/20250618-net-k1-emac-v2-0-94f5f07227a8@iscas.ac.cn
>>
>> Changes in v2:
>> - dts: Put eth0 and eth1 nodes under a bus with dma-ranges
>> - dts: Added Milk-V Jupiter
>> - Fix typo in emac_init_hw() that broke the driver (Oops!)
>> - Reformatted line lengths to under 80
>> - Addressed other v1 review comments
>> - Link to v1: https://lore.kernel.org/r/20250613-net-k1-emac-v1-0-cc6f9e510667@iscas.ac.cn
>>
>> ---
>> Vivian Wang (5):
>> dt-bindings: net: Add support for SpacemiT K1
>> net: spacemit: Add K1 Ethernet MAC
>> riscv: dts: spacemit: Add Ethernet support for K1
>> riscv: dts: spacemit: Add Ethernet support for BPI-F3
>> riscv: dts: spacemit: Add Ethernet support for Jupiter
> I'm unsure on the plan for merging this. But it seems to me that the first
> two patches ought to go though net-next. But in order for patches to
> proceed through net-next the entire series ought to apply on that tree - so
> CI can run.
>
> I'm not sure on the way forward. But perhaps splitting the series in two:
> the first two patches for net-next; and, the riscv patches targeted elsewhere
> makes sense?
Oops. I had not considered this originally, since v1 only depended on
the reset stuff, which seemed like it was going to be taken up at
v6.16-rc1. That did not happen, and this unfortunately also gained a
dependency on DMA buses. So:
I will send a v4 fixing suggestions here but with only patch 1 and 2,
i.e. bindings and driver. The DTS changes will go through the SpacemiT tree.
Thanks for the suggestion.
Regards,
Vivian "dramforever" Wang
> </2c>
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter
2025-07-03 6:48 ` Junhui Liu
@ 2025-07-03 7:46 ` Vivian Wang
2025-07-03 9:00 ` Junhui Liu
0 siblings, 1 reply; 15+ messages in thread
From: Vivian Wang @ 2025-07-03 7:46 UTC (permalink / raw)
To: Junhui Liu, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Yixun Lan, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
Hi Junhui,
On 7/3/25 14:48, Junhui Liu wrote:
> Hi Vivian,
> Thanks for you work!
>
> On 2025/7/2 14:01, Vivian Wang wrote:
>> Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
>> reset.
>>
>> Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
>
> Successfully tested with iperf3 on Milk-V Jupiter.
>
> TCP Rx: 941 Mbits/sec
> TCP Tx: 943 Mbits/sec
> UDP Rx: 956 Mbits/sec
> UDP Tx: 956 Mbits/sec
>
> Tested-by: Junhui Liu <junhui.liu@pigmoral.tech>
>
Thanks for the testing! I do not have a Milk-V Jupiter handy, so that
was very helpful.
As discussed [1], I will post a v4 soon with minor fixes and also sans
the DTS changes. I will put your Tested-by on the driver patch instead
of this DTS patch, so it will show up in v4.
Are you okay with this? If you don't like it feel free to tell me.
Regards,
Vivian "dramforever" Wang
[1]: https://lore.kernel.org/spacemit/a9cad07c-0973-43c3-89f3-95b856b575df@iscas.ac.cn/
>> ---
>> arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46
>> +++++++++++++++++++++++
>> 1 file changed, 46 insertions(+)
>>
>> diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>> b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>> index
>> 4483192141049caa201c093fb206b6134a064f42..c5933555c06b66f40e61fe2b9c159ba0770c2fa1
>> 100644
>> --- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>> +++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>> @@ -20,6 +20,52 @@ chosen {
>> };
>> };
>> +ð0 {
>> + phy-handle = <&rgmii0>;
>> + phy-mode = "rgmii-id";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&gmac0_cfg>;
>> + rx-internal-delay-ps = <0>;
>> + tx-internal-delay-ps = <0>;
>> + status = "okay";
>> +
>> + mdio-bus {
>> + #address-cells = <0x1>;
>> + #size-cells = <0x0>;
>> +
>> + reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
>> + reset-delay-us = <10000>;
>> + reset-post-delay-us = <100000>;
>> +
>> + rgmii0: phy@1 {
>> + reg = <0x1>;
>> + };
>> + };
>> +};
>> +
>> +ð1 {
>> + phy-handle = <&rgmii1>;
>> + phy-mode = "rgmii-id";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&gmac1_cfg>;
>> + rx-internal-delay-ps = <0>;
>> + tx-internal-delay-ps = <250>;
>> + status = "okay";
>> +
>> + mdio-bus {
>> + #address-cells = <0x1>;
>> + #size-cells = <0x0>;
>> +
>> + reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
>> + reset-delay-us = <10000>;
>> + reset-post-delay-us = <100000>;
>> +
>> + rgmii1: phy@1 {
>> + reg = <0x1>;
>> + };
>> + };
>> +};
>> +
>> &uart0 {
>> pinctrl-names = "default";
>> pinctrl-0 = <&uart0_2_cfg>;
>>
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC
2025-07-03 7:19 ` Simon Horman
@ 2025-07-03 7:58 ` Vivian Wang
0 siblings, 0 replies; 15+ messages in thread
From: Vivian Wang @ 2025-07-03 7:58 UTC (permalink / raw)
To: Simon Horman
Cc: Andrew Lunn, David S. Miller, Eric Dumazet, Jakub Kicinski,
Paolo Abeni, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Yixun Lan, Philipp Zabel, Paul Walmsley, Palmer Dabbelt,
Albert Ou, Alexandre Ghiti, Vivian Wang, Lukas Bulwahn,
Geert Uytterhoeven, Parthiban Veerasooran, netdev, devicetree,
linux-riscv, spacemit, linux-kernel
Hi Simon,
Thanks for the suggestions.
On 7/3/25 15:19, Simon Horman wrote:
> On Wed, Jul 02, 2025 at 02:01:41PM +0800, Vivian Wang wrote:
>
> ...
>
>> diff --git a/drivers/net/ethernet/spacemit/k1_emac.c b/drivers/net/ethernet/spacemit/k1_emac.c
> ...
>
>> +static int emac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
>> +{
>> + struct emac_priv *priv = netdev_priv(ndev);
>> + int nfrags = skb_shinfo(skb)->nr_frags;
>> + struct device *dev = &priv->pdev->dev;
>> +
>> + if (unlikely(emac_tx_avail(priv) < nfrags + 1)) {
>> + if (!netif_queue_stopped(ndev)) {
>> + netif_stop_queue(ndev);
>> + dev_err_ratelimited(dev, "TX ring full, stop TX queue\n");
>> + }
>> + return NETDEV_TX_BUSY;
>> + }
>> +
>> + emac_tx_mem_map(priv, skb);
>> +
>> + ndev->stats.tx_packets++;
>> + ndev->stats.tx_bytes += skb->len;
>> +
>> + /* Make sure there is space in the ring for the next TX. */
>> + if (unlikely(emac_tx_avail(priv) <= MAX_SKB_FRAGS + 2))
>> + netif_stop_queue(ndev);
>> +
>> + return NETDEV_TX_OK;
>> +}
>> +
>> +static u32 emac_tx_read_stat_cnt(struct emac_priv *priv, u8 cnt)
>> +{
>> + u32 val, tmp;
>> + int ret;
>> +
>> + val = 0x8000 | cnt;
>> + emac_wr(priv, MAC_TX_STATCTR_CONTROL, val);
>> + val = emac_rd(priv, MAC_TX_STATCTR_CONTROL);
>> +
>> + ret = readl_poll_timeout_atomic(priv->iobase + MAC_TX_STATCTR_CONTROL,
>> + val, !(val & 0x8000), 100, 10000);
>> +
>> + if (ret) {
>> + netdev_err(priv->ndev, "read TX stat timeout\n");
>> + return ret;
>> + }
>> +
>> + tmp = emac_rd(priv, MAC_TX_STATCTR_DATA_HIGH);
>> + val = tmp << 16;
>> + tmp = emac_rd(priv, MAC_TX_STATCTR_DATA_LOW);
>> + val |= tmp;
>> +
>> + return val;
>> +}
>> +
>> +static u32 emac_rx_read_stat_cnt(struct emac_priv *priv, u8 cnt)
>> +{
>> + u32 val, tmp;
>> + int ret;
>> +
>> + val = 0x8000 | cnt;
>> + emac_wr(priv, MAC_RX_STATCTR_CONTROL, val);
>> + val = emac_rd(priv, MAC_RX_STATCTR_CONTROL);
>> +
>> + ret = readl_poll_timeout_atomic(priv->iobase + MAC_RX_STATCTR_CONTROL,
>> + val, !(val & 0x8000), 100, 10000);
>> +
>> + if (ret) {
>> + netdev_err(priv->ndev, "read RX stat timeout\n");
>> + return ret;
>> + }
>> +
>> + tmp = emac_rd(priv, MAC_RX_STATCTR_DATA_HIGH);
>> + val = tmp << 16;
>> + tmp = emac_rd(priv, MAC_RX_STATCTR_DATA_LOW);
>> + val |= tmp;
>> +
>> + return val;
>> +}
>> +
>> +static int emac_set_mac_address(struct net_device *ndev, void *addr)
>> +{
>> + struct emac_priv *priv = netdev_priv(ndev);
>> + int ret = eth_mac_addr(ndev, addr);
>> +
>> + if (ret)
>> + return ret;
>> +
>> + /* If running, set now; if not running it will be set in emac_up. */
>> + if (netif_running(ndev))
>> + emac_set_mac_addr(priv, ndev->dev_addr);
>> +
>> + return 0;
>> +}
>> +
>> +static void emac_mac_multicast_filter_clear(struct emac_priv *priv)
>> +{
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0x0);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0x0);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0x0);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0x0);
>> +}
>> +
>> +/* Configure Multicast and Promiscuous modes */
>> +static void emac_rx_mode_set(struct net_device *ndev)
>> +{
>> + struct emac_priv *priv = netdev_priv(ndev);
>> + u32 crc32, bit, reg, hash, val;
>> + struct netdev_hw_addr *ha;
>> + u32 mc_filter[4] = { 0 };
>> +
>> + val = emac_rd(priv, MAC_ADDRESS_CONTROL);
>> +
>> + val &= ~MREGBIT_PROMISCUOUS_MODE;
>> +
>> + if (ndev->flags & IFF_PROMISC) {
>> + /* Enable promisc mode */
>> + val |= MREGBIT_PROMISCUOUS_MODE;
>> + } else if ((ndev->flags & IFF_ALLMULTI) ||
>> + (netdev_mc_count(ndev) > HASH_TABLE_SIZE)) {
>> + /* Accept all multicast frames by setting every bit */
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, 0xffff);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, 0xffff);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, 0xffff);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, 0xffff);
>> + } else if (!netdev_mc_empty(ndev)) {
>> + emac_mac_multicast_filter_clear(priv);
>> + netdev_for_each_mc_addr(ha, ndev) {
>> + /* Calculate the CRC of the MAC address */
>> + crc32 = ether_crc(ETH_ALEN, ha->addr);
>> +
>> + /*
>> + * The hash table is an array of 4 16-bit registers. It
>> + * is treated like an array of 64 bits (bits[hash]). Use
>> + * the upper 6 bits of the above CRC as the hash value.
>> + */
>> + hash = (crc32 >> 26) & 0x3F;
>> + reg = hash / 16;
>> + bit = hash % 16;
>> + mc_filter[reg] |= BIT(bit);
>> + }
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE1, mc_filter[0]);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE2, mc_filter[1]);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE3, mc_filter[2]);
>> + emac_wr(priv, MAC_MULTICAST_HASH_TABLE4, mc_filter[3]);
>> + }
>> +
>> + emac_wr(priv, MAC_ADDRESS_CONTROL, val);
>> +}
>> +
>> +static int emac_change_mtu(struct net_device *ndev, int mtu)
>> +{
>> + struct emac_priv *priv = netdev_priv(ndev);
>> + u32 frame_len;
>> +
>> + if (netif_running(ndev)) {
>> + netdev_err(ndev, "must be stopped to change MTU\n");
>> + return -EBUSY;
>> + }
>> +
>> + frame_len = mtu + ETH_HLEN + ETH_FCS_LEN;
>> +
>> + if (frame_len <= EMAC_DEFAULT_BUFSIZE)
>> + priv->dma_buf_sz = EMAC_DEFAULT_BUFSIZE;
>> + else if (frame_len <= EMAC_RX_BUF_2K)
>> + priv->dma_buf_sz = EMAC_RX_BUF_2K;
>> + else
>> + priv->dma_buf_sz = EMAC_RX_BUF_4K;
>> +
>> + ndev->mtu = mtu;
>> +
>> + return 0;
>> +}
>> +
>> +static void emac_tx_timeout(struct net_device *ndev, unsigned int txqueue)
>> +{
>> + struct emac_priv *priv = netdev_priv(ndev);
>> +
>> + schedule_work(&priv->tx_timeout_task);
>> +}
>> +
>> +static int emac_mii_read(struct mii_bus *bus, int phy_addr, int regnum)
>> +{
>> + struct emac_priv *priv = bus->priv;
>> + u32 cmd = 0, val;
>> + int ret;
>> +
>> + cmd |= phy_addr & 0x1F;
>> + cmd |= (regnum & 0x1F) << 5;
>> + cmd |= MREGBIT_START_MDIO_TRANS | MREGBIT_MDIO_READ_WRITE;
>> +
>> + emac_wr(priv, MAC_MDIO_DATA, 0x0);
>> + emac_wr(priv, MAC_MDIO_CONTROL, cmd);
>> +
>> + ret = readl_poll_timeout(priv->iobase + MAC_MDIO_CONTROL, val,
>> + !((val >> 15) & 0x1), 100, 10000);
>> +
>> + if (ret)
>> + return ret;
>> +
>> + val = emac_rd(priv, MAC_MDIO_DATA);
>> + return val;
>> +}
>> +
>> +static int emac_mii_write(struct mii_bus *bus, int phy_addr, int regnum,
>> + u16 value)
>> +{
>> + struct emac_priv *priv = bus->priv;
>> + u32 cmd = 0, val;
>> + int ret;
>> +
>> + emac_wr(priv, MAC_MDIO_DATA, value);
>> +
>> + cmd |= phy_addr & 0x1F;
>> + cmd |= (regnum & 0x1F) << 5;
>> + cmd |= MREGBIT_START_MDIO_TRANS;
>> +
>> + emac_wr(priv, MAC_MDIO_CONTROL, cmd);
>> +
>> + ret = readl_poll_timeout(priv->iobase + MAC_MDIO_CONTROL, val,
>> + !((val >> 15) & 0x1), 100, 10000);
>> +
>> + return ret;
>> +}
>> +
>> +static int emac_mdio_init(struct emac_priv *priv)
>> +{
>> + struct device *dev = &priv->pdev->dev;
>> + struct device_node *mii_np;
>> + struct mii_bus *mii;
>> + int ret;
>> +
>> + mii = devm_mdiobus_alloc(dev);
>> + if (!mii)
>> + return -ENOMEM;
>> +
>> + mii->priv = priv;
>> + mii->name = "k1_emac_mii";
>> + mii->read = emac_mii_read;
>> + mii->write = emac_mii_write;
>> + mii->parent = dev;
>> + mii->phy_mask = 0xffffffff;
>> + snprintf(mii->id, MII_BUS_ID_SIZE, "%s", priv->pdev->name);
>> +
>> + mii_np = of_get_available_child_by_name(dev->of_node, "mdio-bus");
>> +
>> + ret = devm_of_mdiobus_register(dev, mii, mii_np);
>> + if (ret)
>> + dev_err_probe(dev, ret, "Failed to register mdio bus\n");
>> +
>> + of_node_put(mii_np);
>> + return ret;
>> +}
>> +
>> +static void emac_get_strings(struct net_device *dev, u32 stringset, u8 *data)
>> +{
>> + int i;
>> +
>> + switch (stringset) {
>> + case ETH_SS_STATS:
>> + for (i = 0; i < ARRAY_SIZE(emac_ethtool_stats); i++) {
>> + memcpy(data, emac_ethtool_stats[i].str,
>> + ETH_GSTRING_LEN);
>> + data += ETH_GSTRING_LEN;
>> + }
>> + break;
>> + }
>> +}
>> +
>> +static int emac_get_sset_count(struct net_device *dev, int sset)
>> +{
>> + switch (sset) {
>> + case ETH_SS_STATS:
>> + return ARRAY_SIZE(emac_ethtool_stats);
>> + default:
>> + return -EOPNOTSUPP;
>> + }
>> +}
>> +
>> +static void emac_stats_update(struct emac_priv *priv)
>> +{
>> + struct emac_hw_stats *hwstats = priv->hw_stats;
>> + u32 *stats = (u32 *)hwstats;
>> + int i;
>> +
>> + for (i = 0; i < EMAC_TX_STATS_NUM; i++)
>> + stats[i] = emac_tx_read_stat_cnt(priv, i);
>> +
>> + for (i = 0; i < EMAC_RX_STATS_NUM; i++)
>> + stats[i + EMAC_TX_STATS_NUM] = emac_rx_read_stat_cnt(priv, i);
>> +}
>> +
>> +static void emac_get_ethtool_stats(struct net_device *dev,
>> + struct ethtool_stats *stats, u64 *data)
>> +{
>> + struct emac_priv *priv = netdev_priv(dev);
>> + struct emac_hw_stats *hwstats;
>> + unsigned long flags;
>> + u32 *data_src;
>> + u64 *data_dst;
>> + int i;
>> +
>> + hwstats = priv->hw_stats;
>> +
>> + if (netif_running(dev) && netif_device_present(dev)) {
>> + if (spin_trylock_irqsave(&priv->stats_lock, flags)) {
>> + emac_stats_update(priv);
>> + spin_unlock_irqrestore(&priv->stats_lock, flags);
>> + }
>> + }
>> +
>> + data_dst = data;
>> +
>> + for (i = 0; i < ARRAY_SIZE(emac_ethtool_stats); i++) {
>> + data_src = (u32 *)hwstats + emac_ethtool_stats[i].offset;
>> + *data_dst++ = (u64)(*data_src);
>> + }
>> +}
>> +
>> +static int emac_ethtool_get_regs_len(struct net_device *dev)
>> +{
>> + return (EMAC_DMA_REG_CNT + EMAC_MAC_REG_CNT) * sizeof(u32);
>> +}
>> +
>> +static void emac_ethtool_get_regs(struct net_device *dev,
>> + struct ethtool_regs *regs, void *space)
>> +{
>> + struct emac_priv *priv = netdev_priv(dev);
>> + u32 *reg_space = space;
>> + int i;
>> +
>> + regs->version = 1;
>> +
>> + for (i = 0; i < EMAC_DMA_REG_CNT; i++)
>> + reg_space[i] = emac_rd(priv, DMA_CONFIGURATION + i * 4);
>> +
>> + for (i = 0; i < EMAC_MAC_REG_CNT; i++)
>> + reg_space[i + EMAC_DMA_REG_CNT] =
>> + emac_rd(priv, MAC_GLOBAL_CONTROL + i * 4);
>> +}
>> +
>> +static void emac_get_drvinfo(struct net_device *dev,
>> + struct ethtool_drvinfo *info)
>> +{
>> + strscpy(info->driver, DRIVER_NAME, sizeof(info->driver));
>> + info->n_stats = ARRAY_SIZE(emac_ethtool_stats);
>> +}
>> +
>> +static void emac_tx_timeout_task(struct work_struct *work)
>> +{
>> + struct net_device *ndev;
>> + struct emac_priv *priv;
>> +
>> + priv = container_of(work, struct emac_priv, tx_timeout_task);
>> + ndev = priv->ndev;
>> +
>> + rtnl_lock();
>> +
>> + /* No need to reset if already down */
>> + if (!netif_running(ndev)) {
>> + rtnl_unlock();
>> + return;
>> + }
>> +
>> + netdev_err(ndev, "MAC reset due to TX timeout\n");
>> +
>> + netif_trans_update(ndev); /* prevent tx timeout */
>> + dev_close(ndev);
>> + dev_open(ndev, NULL);
>> +
>> + rtnl_unlock();
>> +}
>> +
>> +static void emac_sw_init(struct emac_priv *priv)
>> +{
>> + priv->dma_buf_sz = EMAC_DEFAULT_BUFSIZE;
>> +
>> + priv->tx_ring.total_cnt = DEFAULT_TX_RING_NUM;
>> + priv->rx_ring.total_cnt = DEFAULT_RX_RING_NUM;
>> +
>> + spin_lock_init(&priv->stats_lock);
>> +
>> + INIT_WORK(&priv->tx_timeout_task, emac_tx_timeout_task);
>> +
>> + priv->tx_coal_frames = EMAC_TX_FRAMES;
>> + priv->tx_coal_timeout = EMAC_TX_COAL_TIMEOUT;
>> +
>> + timer_setup(&priv->txtimer, emac_tx_coal_timer, 0);
>> +}
>> +
> ...
>
>> +static irqreturn_t emac_interrupt_handler(int irq, void *dev_id)
>> +{
>> + struct net_device *ndev = (struct net_device *)dev_id;
>> + struct emac_priv *priv = netdev_priv(ndev);
>> + bool should_schedule = false;
>> + u32 status;
>> + u32 clr = 0;
> nit: Reverse xmas tree - longest line to shortest - for
> these local variable declarations please.
>
> Edward Cree's tool can be helpful here:
> https://github.com/ecree-solarflare/xmastree/commits/master/
>
> ...
>
Thanks for the script. I was indeed doing reverse xmas tree manually.
I will fix next version.
>> +static const struct net_device_ops emac_netdev_ops = {
>> + .ndo_open = emac_open,
>> + .ndo_stop = emac_close,
>> + .ndo_start_xmit = emac_start_xmit,
> I think that of emac_start_xmit should return netdev_tx_t rather than int
> to match the type of the .ndo_start_xmit member of this structure.
>
> Flagged by Clang 20.1.7 [-Wincompatible-function-pointer-types-strict]
I will fix the type next version.
Regards,
Vivian "dramforever" Wang
>> + .ndo_set_mac_address = emac_set_mac_address,
>> + .ndo_eth_ioctl = phy_do_ioctl_running,
>> + .ndo_change_mtu = emac_change_mtu,
>> + .ndo_tx_timeout = emac_tx_timeout,
>> + .ndo_set_rx_mode = emac_rx_mode_set,
>> +};
> ...
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter
2025-07-03 7:46 ` Vivian Wang
@ 2025-07-03 9:00 ` Junhui Liu
0 siblings, 0 replies; 15+ messages in thread
From: Junhui Liu @ 2025-07-03 9:00 UTC (permalink / raw)
To: Vivian Wang, Andrew Lunn, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Yixun Lan, Philipp Zabel, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Vivian Wang, Lukas Bulwahn, Geert Uytterhoeven,
Parthiban Veerasooran, netdev, devicetree, linux-riscv, spacemit,
linux-kernel
Hi Vivian,
On 03/07/2025 15:46, Vivian Wang wrote:
> Hi Junhui,
>
> On 7/3/25 14:48, Junhui Liu wrote:
>> Hi Vivian,
>> Thanks for you work!
>>
>> On 2025/7/2 14:01, Vivian Wang wrote:
>>> Milk-V Jupiter uses an RGMII PHY for each port and uses GPIO for PHY
>>> reset.
>>>
>>> Signed-off-by: Vivian Wang <wangruikang@iscas.ac.cn>
>>
>> Successfully tested with iperf3 on Milk-V Jupiter.
>>
>> TCP Rx: 941 Mbits/sec
>> TCP Tx: 943 Mbits/sec
>> UDP Rx: 956 Mbits/sec
>> UDP Tx: 956 Mbits/sec
>>
>> Tested-by: Junhui Liu <junhui.liu@pigmoral.tech>
>>
> Thanks for the testing! I do not have a Milk-V Jupiter handy, so that
> was very helpful.
>
> As discussed [1], I will post a v4 soon with minor fixes and also sans
> the DTS changes. I will put your Tested-by on the driver patch instead
> of this DTS patch, so it will show up in v4.
>
> Are you okay with this? If you don't like it feel free to tell me.
It's okay to me. Thanks!
>
> Regards,
> Vivian "dramforever" Wang
>
> [1]: https://lore.kernel.org/spacemit/a9cad07c-0973-43c3-89f3-95b856b575df@iscas.ac.cn/
>
>>> ---
>>> arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 46
>>> +++++++++++++++++++++++
>>> 1 file changed, 46 insertions(+)
>>>
>>> diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>>> b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>>> index
>>> 4483192141049caa201c093fb206b6134a064f42..c5933555c06b66f40e61fe2b9c159ba0770c2fa1
>>> 100644
>>> --- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>>> +++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
>>> @@ -20,6 +20,52 @@ chosen {
>>> };
>>> };
>>> +ð0 {
>>> + phy-handle = <&rgmii0>;
>>> + phy-mode = "rgmii-id";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&gmac0_cfg>;
>>> + rx-internal-delay-ps = <0>;
>>> + tx-internal-delay-ps = <0>;
>>> + status = "okay";
>>> +
>>> + mdio-bus {
>>> + #address-cells = <0x1>;
>>> + #size-cells = <0x0>;
>>> +
>>> + reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
>>> + reset-delay-us = <10000>;
>>> + reset-post-delay-us = <100000>;
>>> +
>>> + rgmii0: phy@1 {
>>> + reg = <0x1>;
>>> + };
>>> + };
>>> +};
>>> +
>>> +ð1 {
>>> + phy-handle = <&rgmii1>;
>>> + phy-mode = "rgmii-id";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&gmac1_cfg>;
>>> + rx-internal-delay-ps = <0>;
>>> + tx-internal-delay-ps = <250>;
>>> + status = "okay";
>>> +
>>> + mdio-bus {
>>> + #address-cells = <0x1>;
>>> + #size-cells = <0x0>;
>>> +
>>> + reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
>>> + reset-delay-us = <10000>;
>>> + reset-post-delay-us = <100000>;
>>> +
>>> + rgmii1: phy@1 {
>>> + reg = <0x1>;
>>> + };
>>> + };
>>> +};
>>> +
>>> &uart0 {
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&uart0_2_cfg>;
>>>
--
Best regards,
Junhui Liu
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2025-07-03 10:06 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-07-02 6:01 [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 1/5] dt-bindings: net: Add " Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 2/5] net: spacemit: Add K1 Ethernet MAC Vivian Wang
2025-07-02 7:17 ` Maxime Chevallier
2025-07-02 7:41 ` Vivian Wang
2025-07-03 7:19 ` Simon Horman
2025-07-03 7:58 ` Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 3/5] riscv: dts: spacemit: Add Ethernet support for K1 Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 4/5] riscv: dts: spacemit: Add Ethernet support for BPI-F3 Vivian Wang
2025-07-02 6:01 ` [PATCH net-next v3 5/5] riscv: dts: spacemit: Add Ethernet support for Jupiter Vivian Wang
2025-07-03 6:48 ` Junhui Liu
2025-07-03 7:46 ` Vivian Wang
2025-07-03 9:00 ` Junhui Liu
2025-07-03 7:23 ` [PATCH net-next v3 0/5] Add Ethernet MAC support for SpacemiT K1 Simon Horman
2025-07-03 7:39 ` Vivian Wang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).