[PATCH v3 0/3] Add Sophgo EVB V1/V2 Board support

[PATCH v3 0/3] Add Sophgo EVB V1/V2 Board support

[Han Gao]

Sophgo EVB V1/V2 [1][2] is a prototype board based on SOPHON SG2042 [3].
There are many of these two boards in the hands of developers.

Currently supports serial port, sdcard/emmc, pwm, fan speed control.

Added ethernet support based on [4].

Changed from v2:
merge v1/v2 binding
v2: https://lore.kernel.org/linux-riscv/cover.1747231254.git.rabenda.cn@gmail.com/

Changed from v1:
1. replace "sophgo,sg2042-x8/4-evb" with "sophgo,sg2042-evb-v1/2".
2. replace "Sophgo SG2042 X8/X4 EVB" with "Sophgo SG2042 EVB V1.X/V2.0".
v1: https://lore.kernel.org/linux-riscv/cover.1746811744.git.rabenda.cn@gmail.com/

Thanks,
Han

[1]: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB
[2]: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x4-EVB
[3]: https://en.sophgo.com/product/introduce/sg2042.html
[4]: https://lore.kernel.org/all/20250506093256.1107770-5-inochiama@gmail.com/

Han Gao (3):
  dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings
  riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree
  riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree

 .../devicetree/bindings/riscv/sophgo.yaml     |   2 +
 arch/riscv/boot/dts/sophgo/Makefile           |   2 +
 arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts  | 245 ++++++++++++++++++
 arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts  | 233 +++++++++++++++++
 4 files changed, 482 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
 create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts


base-commit: d0b3b7b22dfa1f4b515fd3a295b3fd958f9e81af
prerequisite-patch-id: 7a82e319b011e5d0486a6ef4216d931d671c9f53
prerequisite-patch-id: 5a30fb99ec483c1f5a8dca97df862c3a042c9027
prerequisite-patch-id: e0da79790a934916d9fc39c18e8e98c9596d27ab
prerequisite-patch-id: 84d1e1637549f632729eaeb7cf935ca78a642fe3
-- 
2.47.2


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v3 1/3] dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings

[Han Gao]

Add DT binding documentation for the Sophgo SG2042_EVB_V1.X/V2.0 board [1].

Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB [1]

Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Han Gao <rabenda.cn@gmail.com>
---
 Documentation/devicetree/bindings/riscv/sophgo.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/riscv/sophgo.yaml b/Documentation/devicetree/bindings/riscv/sophgo.yaml
index b4c4d7a7d7ad..e21b65938a65 100644
--- a/Documentation/devicetree/bindings/riscv/sophgo.yaml
+++ b/Documentation/devicetree/bindings/riscv/sophgo.yaml
@@ -34,6 +34,8 @@ properties:
       - items:
           - enum:
               - milkv,pioneer
+              - sophgo,sg2042-evb-v1
+              - sophgo,sg2042-evb-v2
           - const: sophgo,sg2042
       - items:
           - enum:
-- 
2.47.2


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v3 2/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree

[Han Gao]

Sophgo SG2042_EVB_V1.X [1] is a prototype development board based on SG2042

Currently supports serial port, sdcard/emmc, pwm, fan speed control.

Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB [1]

Signed-off-by: Han Gao <rabenda.cn@gmail.com>
---
 arch/riscv/boot/dts/sophgo/Makefile          |   1 +
 arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts | 245 +++++++++++++++++++
 2 files changed, 246 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts

diff --git a/arch/riscv/boot/dts/sophgo/Makefile b/arch/riscv/boot/dts/sophgo/Makefile
index 85966306801e..6c9b29681cad 100644
--- a/arch/riscv/boot/dts/sophgo/Makefile
+++ b/arch/riscv/boot/dts/sophgo/Makefile
@@ -3,4 +3,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1800b-milkv-duo.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
+dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2044-sophgo-srd3-10.dtb
diff --git a/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts b/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
new file mode 100644
index 000000000000..3320bc1dd2c6
--- /dev/null
+++ b/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
@@ -0,0 +1,245 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
+ */
+
+#include "sg2042.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Sophgo SG2042 EVB V1.X";
+	compatible = "sophgo,sg2042-evb-v1", "sophgo,sg2042";
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	gpio-power {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power Key";
+			linux,code = <KEY_POWER>;
+			gpios = <&port0a 22 GPIO_ACTIVE_HIGH>;
+			linux,input-type = <EV_KEY>;
+			debounce-interval = <100>;
+		};
+	};
+
+	pwmfan: pwm-fan {
+		compatible = "pwm-fan";
+		cooling-levels = <103 128 179 230 255>;
+		pwms = <&pwm 0 40000 0>;
+		#cooling-cells = <2>;
+	};
+
+	thermal-zones {
+		soc-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+			thermal-sensors = <&mcu 0>;
+
+			trips {
+				soc_active1: soc-active1 {
+					temperature = <30000>;
+					hysteresis = <8000>;
+					type = "active";
+				};
+
+				soc_active2: soc-active2 {
+					temperature = <58000>;
+					hysteresis = <12000>;
+					type = "active";
+				};
+
+				soc_active3: soc-active3 {
+					temperature = <70000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+
+				soc_hot: soc-hot {
+					temperature = <80000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&soc_active1>;
+					cooling-device = <&pwmfan 0 1>;
+				};
+
+				map1 {
+					trip = <&soc_active2>;
+					cooling-device = <&pwmfan 1 2>;
+				};
+
+				map2 {
+					trip = <&soc_active3>;
+					cooling-device = <&pwmfan 2 3>;
+				};
+
+				map3 {
+					trip = <&soc_hot>;
+					cooling-device = <&pwmfan 3 4>;
+				};
+			};
+		};
+
+		board-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+			thermal-sensors = <&mcu 1>;
+
+			trips {
+				board_active: board-active {
+					temperature = <75000>;
+					hysteresis = <8000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map4 {
+					trip = <&board_active>;
+					cooling-device = <&pwmfan 3 4>;
+				};
+			};
+		};
+	};
+};
+
+&cgi_main {
+	clock-frequency = <25000000>;
+};
+
+&cgi_dpll0 {
+	clock-frequency = <25000000>;
+};
+
+&cgi_dpll1 {
+	clock-frequency = <25000000>;
+};
+
+&emmc {
+	pinctrl-0 = <&emmc_cfg>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	wp-inverted;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mcu: syscon@17 {
+		compatible = "sophgo,sg2042-hwmon-mcu";
+		reg = <0x17>;
+		#thermal-sensor-cells = <1>;
+	};
+};
+
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		phy0: phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+		};
+	};
+};
+
+&pinctrl {
+	emmc_cfg: sdhci-emmc-cfg {
+		sdhci-emmc-wp-pins {
+			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+
+		sdhci-emmc-cd-pins {
+			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+
+		sdhci-emmc-rst-pwr-pins {
+			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
+				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+	};
+
+	i2c1_cfg: i2c1-cfg {
+		i2c1-pins {
+			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
+				 <PINMUX(PIN_IIC1_SCL, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+	};
+
+	sd_cfg: sdhci-sd-cfg {
+		sdhci-sd-cd-wp-pins {
+			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
+				 <PINMUX(PIN_SDIO_WP, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+
+		sdhci-sd-rst-pwr-pins {
+			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
+				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+	};
+
+	uart0_cfg: uart0-cfg {
+		uart0-rx-pins {
+			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
+				 <PINMUX(PIN_UART0_RX, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+	};
+};
+
+&sd {
+	pinctrl-0 = <&sd_cfg>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	wp-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+};
-- 
2.47.2


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v3 3/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree

[Han Gao]

Sophgo SG2042_EVB_V2.0 [1] is a prototype development board based on SG2042

Currently supports serial port, sdcard/emmc, pwm, fan speed control.

Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x4-EVB [1]

Signed-off-by: Han Gao <rabenda.cn@gmail.com>
---
 arch/riscv/boot/dts/sophgo/Makefile          |   1 +
 arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts | 233 +++++++++++++++++++
 2 files changed, 234 insertions(+)
 create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts

diff --git a/arch/riscv/boot/dts/sophgo/Makefile b/arch/riscv/boot/dts/sophgo/Makefile
index 6c9b29681cad..6f65526d4193 100644
--- a/arch/riscv/boot/dts/sophgo/Makefile
+++ b/arch/riscv/boot/dts/sophgo/Makefile
@@ -4,4 +4,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
+dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v2.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2044-sophgo-srd3-10.dtb
diff --git a/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts b/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
new file mode 100644
index 000000000000..46980e41b886
--- /dev/null
+++ b/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
+ */
+
+#include "sg2042.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Sophgo SG2042 EVB V2.0";
+	compatible = "sophgo,sg2042-evb-v2", "sophgo,sg2042";
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	pwmfan: pwm-fan {
+		compatible = "pwm-fan";
+		cooling-levels = <103 128 179 230 255>;
+		pwms = <&pwm 0 40000 0>;
+		#cooling-cells = <2>;
+	};
+
+	thermal-zones {
+		soc-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+			thermal-sensors = <&mcu 0>;
+
+			trips {
+				soc_active1: soc-active1 {
+					temperature = <30000>;
+					hysteresis = <8000>;
+					type = "active";
+				};
+
+				soc_active2: soc-active2 {
+					temperature = <58000>;
+					hysteresis = <12000>;
+					type = "active";
+				};
+
+				soc_active3: soc-active3 {
+					temperature = <70000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+
+				soc_hot: soc-hot {
+					temperature = <80000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&soc_active1>;
+					cooling-device = <&pwmfan 0 1>;
+				};
+
+				map1 {
+					trip = <&soc_active2>;
+					cooling-device = <&pwmfan 1 2>;
+				};
+
+				map2 {
+					trip = <&soc_active3>;
+					cooling-device = <&pwmfan 2 3>;
+				};
+
+				map3 {
+					trip = <&soc_hot>;
+					cooling-device = <&pwmfan 3 4>;
+				};
+			};
+		};
+
+		board-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+			thermal-sensors = <&mcu 1>;
+
+			trips {
+				board_active: board-active {
+					temperature = <75000>;
+					hysteresis = <8000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map4 {
+					trip = <&board_active>;
+					cooling-device = <&pwmfan 3 4>;
+				};
+			};
+		};
+	};
+};
+
+&cgi_main {
+	clock-frequency = <25000000>;
+};
+
+&cgi_dpll0 {
+	clock-frequency = <25000000>;
+};
+
+&cgi_dpll1 {
+	clock-frequency = <25000000>;
+};
+
+&emmc {
+	pinctrl-0 = <&emmc_cfg>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	wp-inverted;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mcu: syscon@17 {
+		compatible = "sophgo,sg2042-hwmon-mcu";
+		reg = <0x17>;
+		#thermal-sensor-cells = <1>;
+	};
+};
+
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		phy0: phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+		};
+	};
+};
+
+&pinctrl {
+	emmc_cfg: sdhci-emmc-cfg {
+		sdhci-emmc-wp-pins {
+			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+
+		sdhci-emmc-cd-pins {
+			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+
+		sdhci-emmc-rst-pwr-pins {
+			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
+				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+	};
+
+	i2c1_cfg: i2c1-cfg {
+		i2c1-pins {
+			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
+				 <PINMUX(PIN_IIC1_SCL, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+	};
+
+	sd_cfg: sdhci-sd-cfg {
+		sdhci-sd-cd-wp-pins {
+			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
+				 <PINMUX(PIN_SDIO_WP, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+
+		sdhci-sd-rst-pwr-pins {
+			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
+				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+	};
+
+	uart0_cfg: uart0-cfg {
+		uart0-rx-pins {
+			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
+				 <PINMUX(PIN_UART0_RX, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+	};
+};
+
+&sd {
+	pinctrl-0 = <&sd_cfg>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	wp-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+};
-- 
2.47.2


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 1/3] dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings

[Chen Wang]

On 2025/7/5 15:39, Han Gao wrote:
> Add DT binding documentation for the Sophgo SG2042_EVB_V1.X/V2.0 board [1].
>
> Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB [1]
>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Signed-off-by: Han Gao <rabenda.cn@gmail.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
> ---
>   Documentation/devicetree/bindings/riscv/sophgo.yaml | 2 ++
>   1 file changed, 2 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/riscv/sophgo.yaml b/Documentation/devicetree/bindings/riscv/sophgo.yaml
> index b4c4d7a7d7ad..e21b65938a65 100644
> --- a/Documentation/devicetree/bindings/riscv/sophgo.yaml
> +++ b/Documentation/devicetree/bindings/riscv/sophgo.yaml
> @@ -34,6 +34,8 @@ properties:
>         - items:
>             - enum:
>                 - milkv,pioneer
> +              - sophgo,sg2042-evb-v1
> +              - sophgo,sg2042-evb-v2
>             - const: sophgo,sg2042
>         - items:
>             - enum:

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 2/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree

[Chen Wang]

On 2025/7/5 15:39, Han Gao wrote:
> Sophgo SG2042_EVB_V1.X [1] is a prototype development board based on SG2042
>
> Currently supports serial port, sdcard/emmc, pwm, fan speed control.
>
> Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB [1]
>
> Signed-off-by: Han Gao <rabenda.cn@gmail.com>

Reviewed-by: Chen Wang <unicorn_wang@outlook.com>

Just note that the patch for ethernet support has not yet been upstreamed.

> ---
>   arch/riscv/boot/dts/sophgo/Makefile          |   1 +
>   arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts | 245 +++++++++++++++++++
>   2 files changed, 246 insertions(+)
>   create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
>
> diff --git a/arch/riscv/boot/dts/sophgo/Makefile b/arch/riscv/boot/dts/sophgo/Makefile
> index 85966306801e..6c9b29681cad 100644
> --- a/arch/riscv/boot/dts/sophgo/Makefile
> +++ b/arch/riscv/boot/dts/sophgo/Makefile
> @@ -3,4 +3,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1800b-milkv-duo.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
> +dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2044-sophgo-srd3-10.dtb
> diff --git a/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts b/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
> new file mode 100644
> index 000000000000..3320bc1dd2c6
> --- /dev/null
> +++ b/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
> @@ -0,0 +1,245 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
> + */
> +
> +#include "sg2042.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Sophgo SG2042 EVB V1.X";
> +	compatible = "sophgo,sg2042-evb-v1", "sophgo,sg2042";
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	gpio-power {
> +		compatible = "gpio-keys";
> +
> +		key-power {
> +			label = "Power Key";
> +			linux,code = <KEY_POWER>;
> +			gpios = <&port0a 22 GPIO_ACTIVE_HIGH>;
> +			linux,input-type = <EV_KEY>;
> +			debounce-interval = <100>;
> +		};
> +	};
> +
> +	pwmfan: pwm-fan {
> +		compatible = "pwm-fan";
> +		cooling-levels = <103 128 179 230 255>;
> +		pwms = <&pwm 0 40000 0>;
> +		#cooling-cells = <2>;
> +	};
> +
> +	thermal-zones {
> +		soc-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 0>;
> +
> +			trips {
> +				soc_active1: soc-active1 {
> +					temperature = <30000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +
> +				soc_active2: soc-active2 {
> +					temperature = <58000>;
> +					hysteresis = <12000>;
> +					type = "active";
> +				};
> +
> +				soc_active3: soc-active3 {
> +					temperature = <70000>;
> +					hysteresis = <10000>;
> +					type = "active";
> +				};
> +
> +				soc_hot: soc-hot {
> +					temperature = <80000>;
> +					hysteresis = <5000>;
> +					type = "hot";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&soc_active1>;
> +					cooling-device = <&pwmfan 0 1>;
> +				};
> +
> +				map1 {
> +					trip = <&soc_active2>;
> +					cooling-device = <&pwmfan 1 2>;
> +				};
> +
> +				map2 {
> +					trip = <&soc_active3>;
> +					cooling-device = <&pwmfan 2 3>;
> +				};
> +
> +				map3 {
> +					trip = <&soc_hot>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +
> +		board-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 1>;
> +
> +			trips {
> +				board_active: board-active {
> +					temperature = <75000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map4 {
> +					trip = <&board_active>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&cgi_main {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll0 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll1 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&emmc {
> +	pinctrl-0 = <&emmc_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-sd;
> +	non-removable;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-0 = <&i2c1_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mcu: syscon@17 {
> +		compatible = "sophgo,sg2042-hwmon-mcu";
> +		reg = <0x17>;
> +		#thermal-sensor-cells = <1>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-handle = <&phy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	mdio {
> +		phy0: phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <100000>;
> +			reset-deassert-us = <100000>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	emmc_cfg: sdhci-emmc-cfg {
> +		sdhci-emmc-wp-pins {
> +			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +
> +		sdhci-emmc-cd-pins {
> +			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-emmc-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
> +				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	i2c1_cfg: i2c1-cfg {
> +		i2c1-pins {
> +			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
> +				 <PINMUX(PIN_IIC1_SCL, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +
> +	sd_cfg: sdhci-sd-cfg {
> +		sdhci-sd-cd-wp-pins {
> +			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
> +				 <PINMUX(PIN_SDIO_WP, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-sd-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
> +				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	uart0_cfg: uart0-cfg {
> +		uart0-rx-pins {
> +			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
> +				 <PINMUX(PIN_UART0_RX, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +};
> +
> +&sd {
> +	pinctrl-0 = <&sd_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-mmc;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-0 = <&uart0_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 3/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree

[Chen Wang]

On 2025/7/5 15:39, Han Gao wrote:
> Sophgo SG2042_EVB_V2.0 [1] is a prototype development board based on SG2042
>
> Currently supports serial port, sdcard/emmc, pwm, fan speed control.
>
> Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x4-EVB [1]
>
> Signed-off-by: Han Gao <rabenda.cn@gmail.com>

Reviewed-by: Chen Wang <unicorn_wang@outlook.com>

Just note that the patch for ethernet support has not yet been upstreamed.

> ---
>   arch/riscv/boot/dts/sophgo/Makefile          |   1 +
>   arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts | 233 +++++++++++++++++++
>   2 files changed, 234 insertions(+)
>   create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
>
> diff --git a/arch/riscv/boot/dts/sophgo/Makefile b/arch/riscv/boot/dts/sophgo/Makefile
> index 6c9b29681cad..6f65526d4193 100644
> --- a/arch/riscv/boot/dts/sophgo/Makefile
> +++ b/arch/riscv/boot/dts/sophgo/Makefile
> @@ -4,4 +4,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
> +dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v2.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2044-sophgo-srd3-10.dtb
> diff --git a/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts b/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
> new file mode 100644
> index 000000000000..46980e41b886
> --- /dev/null
> +++ b/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
> @@ -0,0 +1,233 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
> + */
> +
> +#include "sg2042.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Sophgo SG2042 EVB V2.0";
> +	compatible = "sophgo,sg2042-evb-v2", "sophgo,sg2042";
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	pwmfan: pwm-fan {
> +		compatible = "pwm-fan";
> +		cooling-levels = <103 128 179 230 255>;
> +		pwms = <&pwm 0 40000 0>;
> +		#cooling-cells = <2>;
> +	};
> +
> +	thermal-zones {
> +		soc-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 0>;
> +
> +			trips {
> +				soc_active1: soc-active1 {
> +					temperature = <30000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +
> +				soc_active2: soc-active2 {
> +					temperature = <58000>;
> +					hysteresis = <12000>;
> +					type = "active";
> +				};
> +
> +				soc_active3: soc-active3 {
> +					temperature = <70000>;
> +					hysteresis = <10000>;
> +					type = "active";
> +				};
> +
> +				soc_hot: soc-hot {
> +					temperature = <80000>;
> +					hysteresis = <5000>;
> +					type = "hot";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&soc_active1>;
> +					cooling-device = <&pwmfan 0 1>;
> +				};
> +
> +				map1 {
> +					trip = <&soc_active2>;
> +					cooling-device = <&pwmfan 1 2>;
> +				};
> +
> +				map2 {
> +					trip = <&soc_active3>;
> +					cooling-device = <&pwmfan 2 3>;
> +				};
> +
> +				map3 {
> +					trip = <&soc_hot>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +
> +		board-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 1>;
> +
> +			trips {
> +				board_active: board-active {
> +					temperature = <75000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map4 {
> +					trip = <&board_active>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&cgi_main {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll0 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll1 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&emmc {
> +	pinctrl-0 = <&emmc_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-sd;
> +	non-removable;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-0 = <&i2c1_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mcu: syscon@17 {
> +		compatible = "sophgo,sg2042-hwmon-mcu";
> +		reg = <0x17>;
> +		#thermal-sensor-cells = <1>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-handle = <&phy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	mdio {
> +		phy0: phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <100000>;
> +			reset-deassert-us = <100000>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	emmc_cfg: sdhci-emmc-cfg {
> +		sdhci-emmc-wp-pins {
> +			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +
> +		sdhci-emmc-cd-pins {
> +			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-emmc-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
> +				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	i2c1_cfg: i2c1-cfg {
> +		i2c1-pins {
> +			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
> +				 <PINMUX(PIN_IIC1_SCL, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +
> +	sd_cfg: sdhci-sd-cfg {
> +		sdhci-sd-cd-wp-pins {
> +			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
> +				 <PINMUX(PIN_SDIO_WP, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-sd-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
> +				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	uart0_cfg: uart0-cfg {
> +		uart0-rx-pins {
> +			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
> +				 <PINMUX(PIN_UART0_RX, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +};
> +
> +&sd {
> +	pinctrl-0 = <&sd_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-mmc;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-0 = <&uart0_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 1/3] dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings

[Nutty Liu]

On 7/5/2025 3:39 PM, Han Gao wrote:
> Add DT binding documentation for the Sophgo SG2042_EVB_V1.X/V2.0 board [1].
>
> Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB [1]
>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Signed-off-by: Han Gao <rabenda.cn@gmail.com>

Reviewed-by: Nutty Liu<liujingqi@lanxincomputing.com>

Thanks,
Nutty

> ---
>   Documentation/devicetree/bindings/riscv/sophgo.yaml | 2 ++
>   1 file changed, 2 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/riscv/sophgo.yaml b/Documentation/devicetree/bindings/riscv/sophgo.yaml
> index b4c4d7a7d7ad..e21b65938a65 100644
> --- a/Documentation/devicetree/bindings/riscv/sophgo.yaml
> +++ b/Documentation/devicetree/bindings/riscv/sophgo.yaml
> @@ -34,6 +34,8 @@ properties:
>         - items:
>             - enum:
>                 - milkv,pioneer
> +              - sophgo,sg2042-evb-v1
> +              - sophgo,sg2042-evb-v2
>             - const: sophgo,sg2042
>         - items:
>             - enum:

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 2/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree

[Nutty Liu]

On 7/5/2025 3:39 PM, Han Gao wrote:
> Sophgo SG2042_EVB_V1.X [1] is a prototype development board based on SG2042
>
> Currently supports serial port, sdcard/emmc, pwm, fan speed control.
>
> Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x8-EVB [1]
>
> Signed-off-by: Han Gao <rabenda.cn@gmail.com>

Reviewed-by: Nutty Liu<liujingqi@lanxincomputing.com>

Thanks,
Nutty

> ---
>   arch/riscv/boot/dts/sophgo/Makefile          |   1 +
>   arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts | 245 +++++++++++++++++++
>   2 files changed, 246 insertions(+)
>   create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
>
> diff --git a/arch/riscv/boot/dts/sophgo/Makefile b/arch/riscv/boot/dts/sophgo/Makefile
> index 85966306801e..6c9b29681cad 100644
> --- a/arch/riscv/boot/dts/sophgo/Makefile
> +++ b/arch/riscv/boot/dts/sophgo/Makefile
> @@ -3,4 +3,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1800b-milkv-duo.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
> +dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2044-sophgo-srd3-10.dtb
> diff --git a/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts b/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
> new file mode 100644
> index 000000000000..3320bc1dd2c6
> --- /dev/null
> +++ b/arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts
> @@ -0,0 +1,245 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
> + */
> +
> +#include "sg2042.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Sophgo SG2042 EVB V1.X";
> +	compatible = "sophgo,sg2042-evb-v1", "sophgo,sg2042";
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	gpio-power {
> +		compatible = "gpio-keys";
> +
> +		key-power {
> +			label = "Power Key";
> +			linux,code = <KEY_POWER>;
> +			gpios = <&port0a 22 GPIO_ACTIVE_HIGH>;
> +			linux,input-type = <EV_KEY>;
> +			debounce-interval = <100>;
> +		};
> +	};
> +
> +	pwmfan: pwm-fan {
> +		compatible = "pwm-fan";
> +		cooling-levels = <103 128 179 230 255>;
> +		pwms = <&pwm 0 40000 0>;
> +		#cooling-cells = <2>;
> +	};
> +
> +	thermal-zones {
> +		soc-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 0>;
> +
> +			trips {
> +				soc_active1: soc-active1 {
> +					temperature = <30000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +
> +				soc_active2: soc-active2 {
> +					temperature = <58000>;
> +					hysteresis = <12000>;
> +					type = "active";
> +				};
> +
> +				soc_active3: soc-active3 {
> +					temperature = <70000>;
> +					hysteresis = <10000>;
> +					type = "active";
> +				};
> +
> +				soc_hot: soc-hot {
> +					temperature = <80000>;
> +					hysteresis = <5000>;
> +					type = "hot";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&soc_active1>;
> +					cooling-device = <&pwmfan 0 1>;
> +				};
> +
> +				map1 {
> +					trip = <&soc_active2>;
> +					cooling-device = <&pwmfan 1 2>;
> +				};
> +
> +				map2 {
> +					trip = <&soc_active3>;
> +					cooling-device = <&pwmfan 2 3>;
> +				};
> +
> +				map3 {
> +					trip = <&soc_hot>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +
> +		board-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 1>;
> +
> +			trips {
> +				board_active: board-active {
> +					temperature = <75000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map4 {
> +					trip = <&board_active>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&cgi_main {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll0 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll1 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&emmc {
> +	pinctrl-0 = <&emmc_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-sd;
> +	non-removable;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-0 = <&i2c1_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mcu: syscon@17 {
> +		compatible = "sophgo,sg2042-hwmon-mcu";
> +		reg = <0x17>;
> +		#thermal-sensor-cells = <1>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-handle = <&phy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	mdio {
> +		phy0: phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <100000>;
> +			reset-deassert-us = <100000>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	emmc_cfg: sdhci-emmc-cfg {
> +		sdhci-emmc-wp-pins {
> +			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +
> +		sdhci-emmc-cd-pins {
> +			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-emmc-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
> +				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	i2c1_cfg: i2c1-cfg {
> +		i2c1-pins {
> +			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
> +				 <PINMUX(PIN_IIC1_SCL, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +
> +	sd_cfg: sdhci-sd-cfg {
> +		sdhci-sd-cd-wp-pins {
> +			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
> +				 <PINMUX(PIN_SDIO_WP, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-sd-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
> +				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	uart0_cfg: uart0-cfg {
> +		uart0-rx-pins {
> +			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
> +				 <PINMUX(PIN_UART0_RX, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +};
> +
> +&sd {
> +	pinctrl-0 = <&sd_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-mmc;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-0 = <&uart0_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 3/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree

[Nutty Liu]

On 7/5/2025 3:39 PM, Han Gao wrote:
> Sophgo SG2042_EVB_V2.0 [1] is a prototype development board based on SG2042
>
> Currently supports serial port, sdcard/emmc, pwm, fan speed control.
>
> Link: https://github.com/sophgo/sophgo-hardware/tree/master/SG2042/SG2042-x4-EVB [1]
>
> Signed-off-by: Han Gao <rabenda.cn@gmail.com>

Reviewed-by: Nutty Liu<liujingqi@lanxincomputing.com>

Thanks,
Nutty

> ---
>   arch/riscv/boot/dts/sophgo/Makefile          |   1 +
>   arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts | 233 +++++++++++++++++++
>   2 files changed, 234 insertions(+)
>   create mode 100644 arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
>
> diff --git a/arch/riscv/boot/dts/sophgo/Makefile b/arch/riscv/boot/dts/sophgo/Makefile
> index 6c9b29681cad..6f65526d4193 100644
> --- a/arch/riscv/boot/dts/sophgo/Makefile
> +++ b/arch/riscv/boot/dts/sophgo/Makefile
> @@ -4,4 +4,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
> +dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v2.dtb
>   dtb-$(CONFIG_ARCH_SOPHGO) += sg2044-sophgo-srd3-10.dtb
> diff --git a/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts b/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
> new file mode 100644
> index 000000000000..46980e41b886
> --- /dev/null
> +++ b/arch/riscv/boot/dts/sophgo/sg2042-evb-v2.dts
> @@ -0,0 +1,233 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
> + */
> +
> +#include "sg2042.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Sophgo SG2042 EVB V2.0";
> +	compatible = "sophgo,sg2042-evb-v2", "sophgo,sg2042";
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	pwmfan: pwm-fan {
> +		compatible = "pwm-fan";
> +		cooling-levels = <103 128 179 230 255>;
> +		pwms = <&pwm 0 40000 0>;
> +		#cooling-cells = <2>;
> +	};
> +
> +	thermal-zones {
> +		soc-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 0>;
> +
> +			trips {
> +				soc_active1: soc-active1 {
> +					temperature = <30000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +
> +				soc_active2: soc-active2 {
> +					temperature = <58000>;
> +					hysteresis = <12000>;
> +					type = "active";
> +				};
> +
> +				soc_active3: soc-active3 {
> +					temperature = <70000>;
> +					hysteresis = <10000>;
> +					type = "active";
> +				};
> +
> +				soc_hot: soc-hot {
> +					temperature = <80000>;
> +					hysteresis = <5000>;
> +					type = "hot";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&soc_active1>;
> +					cooling-device = <&pwmfan 0 1>;
> +				};
> +
> +				map1 {
> +					trip = <&soc_active2>;
> +					cooling-device = <&pwmfan 1 2>;
> +				};
> +
> +				map2 {
> +					trip = <&soc_active3>;
> +					cooling-device = <&pwmfan 2 3>;
> +				};
> +
> +				map3 {
> +					trip = <&soc_hot>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +
> +		board-thermal {
> +			polling-delay-passive = <1000>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&mcu 1>;
> +
> +			trips {
> +				board_active: board-active {
> +					temperature = <75000>;
> +					hysteresis = <8000>;
> +					type = "active";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map4 {
> +					trip = <&board_active>;
> +					cooling-device = <&pwmfan 3 4>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&cgi_main {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll0 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&cgi_dpll1 {
> +	clock-frequency = <25000000>;
> +};
> +
> +&emmc {
> +	pinctrl-0 = <&emmc_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-sd;
> +	non-removable;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-0 = <&i2c1_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	mcu: syscon@17 {
> +		compatible = "sophgo,sg2042-hwmon-mcu";
> +		reg = <0x17>;
> +		#thermal-sensor-cells = <1>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-handle = <&phy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	mdio {
> +		phy0: phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <100000>;
> +			reset-deassert-us = <100000>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	emmc_cfg: sdhci-emmc-cfg {
> +		sdhci-emmc-wp-pins {
> +			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +
> +		sdhci-emmc-cd-pins {
> +			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-emmc-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
> +				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	i2c1_cfg: i2c1-cfg {
> +		i2c1-pins {
> +			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
> +				 <PINMUX(PIN_IIC1_SCL, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +
> +	sd_cfg: sdhci-sd-cfg {
> +		sdhci-sd-cd-wp-pins {
> +			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
> +				 <PINMUX(PIN_SDIO_WP, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +
> +		sdhci-sd-rst-pwr-pins {
> +			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
> +				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
> +			bias-disable;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-disable;
> +		};
> +	};
> +
> +	uart0_cfg: uart0-cfg {
> +		uart0-rx-pins {
> +			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
> +				 <PINMUX(PIN_UART0_RX, 0)>;
> +			bias-pull-up;
> +			drive-strength-microamp = <26800>;
> +			input-schmitt-enable;
> +		};
> +	};
> +};
> +
> +&sd {
> +	pinctrl-0 = <&sd_cfg>;
> +	pinctrl-names = "default";
> +	bus-width = <4>;
> +	no-sdio;
> +	no-mmc;
> +	wp-inverted;
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-0 = <&uart0_cfg>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +};

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 0/3] Add Sophgo EVB V1/V2 Board support

[Inochi Amaoto]

On Sat, 05 Jul 2025 15:39:53 +0800, Han Gao wrote:
> Sophgo EVB V1/V2 [1][2] is a prototype board based on SOPHON SG2042 [3].
> There are many of these two boards in the hands of developers.
> 
> Currently supports serial port, sdcard/emmc, pwm, fan speed control.
> 
> Added ethernet support based on [4].
> 
> [...]

Applied to for-next, thanks!

[1/3] dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings
      https://github.com/sophgo/linux/commit/a42a510c1a9119a8413e20fe09ce3c3cd85ea7db
[2/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree
      https://github.com/sophgo/linux/commit/1bf2708394942e047e08146dc8d2a34c091280de
[3/3] riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree
      https://github.com/sophgo/linux/commit/6ca1c3d005cdb9bd619a2dec6ed63ef9ba29eb37

Thanks,
Inochi


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv