From: Dragan Simic <dsimic@manjaro.org>
To: Alexey Charkov <alchark@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Heiko Stuebner <heiko@sntech.de>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Viresh Kumar <viresh.kumar@linaro.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 1/4] arm64: dts: rockchip: enable built-in thermal monitoring on rk3588
Date: Wed, 31 Jan 2024 06:05:53 +0100 [thread overview]
Message-ID: <0702542c8d7dc4139ba5da690fd98e67@manjaro.org> (raw)
In-Reply-To: <20240130-rk-dts-additions-v2-1-c6222c4c78df@gmail.com>
Hello Alexey,
Some small nitpicks below, please have a look.
On 2024-01-30 19:21, Alexey Charkov wrote:
> Include thermal zones information in device tree for rk3588 variants
Please use "RK3588" instead of "rk3588", both here and in the
patch subject. Looks much better.
> Signed-off-by: Alexey Charkov <alchark@gmail.com>
> ---
> arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 162
> ++++++++++++++++++++++++++++++
> 1 file changed, 162 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> index 36b1b7acfe6a..696cb72d75d0 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
> @@ -10,6 +10,7 @@
> #include <dt-bindings/reset/rockchip,rk3588-cru.h>
> #include <dt-bindings/phy/phy.h>
> #include <dt-bindings/ata/ahci.h>
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> compatible = "rockchip,rk3588";
> @@ -2228,6 +2229,167 @@ tsadc: tsadc@fec00000 {
> status = "disabled";
> };
>
> + thermal_zones: thermal-zones {
> + /* sensor near the center of the whole chip */
It would be good to replace "whole chip" with "SoC". Simpler and
IIRC closer to the official description of the sensor.
> + package_thermal: package-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 0>;
> +
> + trips {
> + package_crit: package-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> +
> + /* sensor between A76 cores 0 and 1 */
> + bigcore0_thermal: bigcore0-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 1>;
> +
> + trips {
Please add the following comment here, to make it clear what's
the purpose of this thermal trip when the IPA thermal governor
is used (more similar comments below):
/* IPA threshold */
> + bigcore0_alert0: bigcore0-alert0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
Please add the following comment here:
/* IPA target */
> + bigcore0_alert1: bigcore0-alert1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + bigcore0_crit: bigcore0-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&bigcore0_alert1>;
> + cooling-device =
> + <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu_b1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + /* sensor between A76 cores 2 and 3 */
> + bigcore2_thermal: bigcore2-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 2>;
> +
> + trips {
Please add the following comment here:
/* IPA threshold */
> + bigcore2_alert0: bigcore2-alert0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
Please add the following comment here:
/* IPA target */
> + bigcore2_alert1: bigcore2-alert1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + bigcore2_crit: bigcore2-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&bigcore2_alert1>;
> + cooling-device =
> + <&cpu_b2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu_b3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + /* sensor between the four A55 cores */
> + little_core_thermal: littlecore-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 3>;
> +
> + trips {
Please add the following comment here:
/* IPA threshold */
> + littlecore_alert0: littlecore-alert0 {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
Please add the following comment here:
/* IPA target */
> + littlecore_alert1: littlecore-alert1 {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + littlecore_crit: littlecore-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + cooling-maps {
> + map0 {
> + trip = <&littlecore_alert1>;
> + cooling-device =
> + <&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu_l1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu_l2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&cpu_l3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + /* sensor near the PD_CENTER power domain */
> + center_thermal: center-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 4>;
> +
> + trips {
> + center_crit: center-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> +
> + gpu_thermal: gpu-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 5>;
> +
> + trips {
> + gpu_crit: gpu-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> +
> + npu_thermal: npu-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&tsadc 6>;
> +
> + trips {
> + npu_crit: npu-crit {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +
> saradc: adc@fec10000 {
> compatible = "rockchip,rk3588-saradc";
> reg = <0x0 0xfec10000 0x0 0x10000>;
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2024-01-31 5:06 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-01-30 18:21 [PATCH v2 0/4] RK3588 and Rock 5B dts additions: thermal, OPP and fan Alexey Charkov
2024-01-30 18:21 ` [PATCH v2 1/4] arm64: dts: rockchip: enable built-in thermal monitoring on rk3588 Alexey Charkov
2024-01-31 5:05 ` Dragan Simic [this message]
2024-01-31 9:56 ` Alexey Charkov
2024-01-31 10:08 ` Dragan Simic
2024-01-30 18:21 ` [PATCH v2 2/4] arm64: dts: rockchip: enable temperature driven fan control on Rock 5B Alexey Charkov
2024-01-31 5:08 ` Dragan Simic
2024-01-31 9:43 ` Alexey Charkov
2024-02-01 14:26 ` Chen-Yu Tsai
2024-02-01 17:34 ` Dragan Simic
2024-02-01 19:15 ` Alexey Charkov
2024-02-01 19:31 ` Dragan Simic
2024-02-01 19:43 ` Dragan Simic
2024-02-02 14:42 ` Alexey Charkov
2024-02-02 20:14 ` Dragan Simic
2024-01-30 18:21 ` [PATCH v2 3/4] arm64: dts: rockchip: Add OPP data for CPU cores on RK3588 Alexey Charkov
2024-01-31 9:12 ` Heiko Stübner
2024-01-31 9:34 ` Alexey Charkov
2024-01-30 18:21 ` [PATCH v2 4/4] arm64: dts: rockchip: Add further granularity in RK3588 CPU OPPs Alexey Charkov
2024-01-31 5:08 ` Dragan Simic
2024-02-08 12:19 ` Dragan Simic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0702542c8d7dc4139ba5da690fd98e67@manjaro.org \
--to=dsimic@manjaro.org \
--cc=alchark@gmail.com \
--cc=conor+dt@kernel.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=heiko@sntech.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=robh+dt@kernel.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox