[PATCH V4 0/5] Add Texas Instruments BQ25703A Charger

[PATCH V4 0/5] Add Texas Instruments BQ25703A Charger

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the Texas Instruments BQ25703A charger manager. The
device integrates a boost converter with the charger manager. This
series adds the device as an MFD with separate regulator and power
supply drivers. This allows us to manage a circular dependency with
a type-c port manager which depends on the regulator for usb-otg
but supplies power to the BQ25703A charger.

---
Changes since RFC
 - Corrected some minor issues with code and device-tree labels.
 - Replaced most of the manufacturer specific device-tree properties
   with monitored-battery properties.
Changes since V2
 - Added reference to power-supply.yaml and removed note for i2c
   address per recommendation from Sebastian.
 - Corrected documentation error for charger driver found by kernel
   test robot.
 - Corrected duplicate POWER_SUPPLY_USB_TYPE_PD entry and corrected
   ichg logic in power supply changed function.
 - Corrected missing linux/bitfield.h header in regulator driver found
   by kernel test robot.
Changes since V3
 - Changed name of regulator from usb_otg_vbus to just vbus to align
   with datasheet.
 - Additional cleanup of the device tree documentation.
---

Chris Morgan (5):
  dt-bindings: mfd: ti,bq25703a: Add TI BQ25703A Charger
  mfd: bq257xx: Add support for BQ25703A core driver
  power: supply: bq257xx: Add support for BQ257XX charger
  regulator: bq257xx: Add bq257xx boost regulator driver
  arm64: dts: rockchip: Add USB and charger to Gameforce Ace

 .../devicetree/bindings/mfd/ti,bq25703a.yaml  | 117 +++
 .../dts/rockchip/rk3588s-gameforce-ace.dts    | 122 +++
 drivers/mfd/Kconfig                           |  11 +
 drivers/mfd/Makefile                          |   1 +
 drivers/mfd/bq257xx.c                         | 104 +++
 drivers/power/supply/Kconfig                  |   7 +
 drivers/power/supply/Makefile                 |   1 +
 drivers/power/supply/bq257xx_charger.c        | 754 ++++++++++++++++++
 drivers/regulator/Kconfig                     |   8 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/bq257xx-regulator.c         | 189 +++++
 include/linux/mfd/bq257xx.h                   | 108 +++
 12 files changed, 1423 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml
 create mode 100644 drivers/mfd/bq257xx.c
 create mode 100644 drivers/power/supply/bq257xx_charger.c
 create mode 100644 drivers/regulator/bq257xx-regulator.c
 create mode 100644 include/linux/mfd/bq257xx.h

-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH V4 1/5] dt-bindings: mfd: ti,bq25703a: Add TI BQ25703A Charger

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Document the Texas instruments BQ25703A series of charger managers/
buck/boost regulators.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../devicetree/bindings/mfd/ti,bq25703a.yaml  | 117 ++++++++++++++++++
 1 file changed, 117 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml

diff --git a/Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml b/Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml
new file mode 100644
index 000000000000..ba14663c9266
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/ti,bq25703a.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: BQ25703A Charger Manager/Buck/Boost Converter
+
+maintainers:
+  - Chris Morgan <macromorgan@hotmail.com>
+
+allOf:
+  - $ref: /schemas/power/supply/power-supply.yaml#
+
+properties:
+  compatible:
+    const: ti,bq25703a
+
+  reg:
+    const: 0x6b
+
+  input-current-limit-microamp:
+    description:
+      Maximum total input current allowed used for both charging and
+      powering the device.
+    minimum: 50000
+    maximum: 6400000
+    default: 3250000
+
+  interrupts:
+    maxItems: 1
+
+  monitored-battery:
+    description:
+      A minimum of constant-charge-current-max-microamp,
+      constant-charge-voltage-max-microvolt, and
+      voltage-min-design-microvolt are required.
+
+  regulators:
+    type: object
+    additionalProperties: false
+    description:
+      Boost converter regulator output of bq257xx.
+
+    properties:
+      vbus:
+        type: object
+        $ref: /schemas/regulator/regulator.yaml
+        additionalProperties: false
+
+        properties:
+          regulator-name: true
+          regulator-min-microamp:
+            minimum: 0
+            maximum: 6350000
+          regulator-max-microamp:
+            minimum: 0
+            maximum: 6350000
+          regulator-min-microvolt:
+            minimum: 4480000
+            maximum: 20800000
+          regulator-max-microvolt:
+            minimum: 4480000
+            maximum: 20800000
+          enable-gpios:
+            description:
+              The BQ25703 may require both a register write and a GPIO
+              toggle to enable the boost regulator.
+
+        required:
+          - regulator-name
+          - regulator-min-microamp
+          - regulator-max-microamp
+          - regulator-min-microvolt
+          - regulator-max-microvolt
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - input-current-limit-microamp
+  - monitored-battery
+  - power-supplies
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/pinctrl/rockchip.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bq25703: charger@6b {
+            compatible = "ti,bq25703a";
+            reg = <0x6b>;
+            input-current-limit-microamp = <5000000>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <RK_PD5 IRQ_TYPE_LEVEL_LOW>;
+            monitored-battery = <&battery>;
+            power-supplies = <&fusb302>;
+
+            regulators {
+                usb_otg_vbus: vbus {
+                    enable-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
+                    regulator-max-microamp = <960000>;
+                    regulator-max-microvolt = <5088000>;
+                    regulator-min-microamp = <512000>;
+                    regulator-min-microvolt = <4992000>;
+                    regulator-name = "usb_otg_vbus";
+                };
+            };
+        };
+    };
+
+...
-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH V4 2/5] mfd: bq257xx: Add support for BQ25703A core driver

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

The Texas Instruments BQ25703A is an integrated charger manager and
boost converter.

The MFD driver initalizes the device for the regulator driver
and power supply driver.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 drivers/mfd/Kconfig         |  11 ++++
 drivers/mfd/Makefile        |   1 +
 drivers/mfd/bq257xx.c       | 104 ++++++++++++++++++++++++++++++++++
 include/linux/mfd/bq257xx.h | 108 ++++++++++++++++++++++++++++++++++++
 4 files changed, 224 insertions(+)
 create mode 100644 drivers/mfd/bq257xx.c
 create mode 100644 include/linux/mfd/bq257xx.h

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 6fb3768e3d71..d8b39e8a8a17 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1585,6 +1585,17 @@ config MFD_TI_LMU
 	  LM36274.  It consists of backlight, LED and regulator driver.
 	  It provides consistent device controls for lighting functions.
 
+config MFD_BQ257XX
+	tristate "TI BQ257XX Buck/Boost Charge Controller"
+	depends on I2C
+	select MFD_CORE
+	select REGMAP_I2C
+	help
+	  Support Texas Instruments BQ25703 Buck/Boost converter with
+	  charge controller. It consists of regulators that provide
+	  system voltage and OTG voltage, and a charger manager for
+	  batteries containing one or more cells.
+
 config MFD_OMAP_USB_HOST
 	bool "TI OMAP USBHS core and TLL driver"
 	depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 79495f9f3457..06da932cce5d 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_MFD_SM501)		+= sm501.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835-pm.o
 obj-$(CONFIG_MFD_BCM590XX)	+= bcm590xx.o
 obj-$(CONFIG_MFD_BD9571MWV)	+= bd9571mwv.o
+obj-$(CONFIG_MFD_BQ257XX)	+= bq257xx.o
 obj-$(CONFIG_MFD_CGBC)		+= cgbc-core.o
 obj-$(CONFIG_MFD_CROS_EC_DEV)	+= cros_ec_dev.o
 obj-$(CONFIG_MFD_CS42L43)	+= cs42l43.o
diff --git a/drivers/mfd/bq257xx.c b/drivers/mfd/bq257xx.c
new file mode 100644
index 000000000000..27fbb64110ed
--- /dev/null
+++ b/drivers/mfd/bq257xx.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * BQ257XX Core Driver
+ * Copyright (C) 2024 Chris Morgan <macromorgan@hotmail.com>
+ */
+
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/mfd/bq257xx.h>
+#include <linux/mfd/core.h>
+#include <linux/regmap.h>
+
+static const struct regmap_range bq25703_readonly_reg_ranges[] = {
+	regmap_reg_range(BQ25703_CHARGER_STATUS, BQ25703_MANUFACT_DEV_ID),
+};
+
+static const struct regmap_access_table bq25703_writeable_regs = {
+	.no_ranges = bq25703_readonly_reg_ranges,
+	.n_no_ranges = ARRAY_SIZE(bq25703_readonly_reg_ranges),
+};
+
+static const struct regmap_range bq25703_volatile_reg_ranges[] = {
+	regmap_reg_range(BQ25703_CHARGE_OPTION_0, BQ25703_IIN_HOST),
+	regmap_reg_range(BQ25703_CHARGER_STATUS, BQ25703_ADC_OPTION),
+};
+
+static const struct regmap_access_table bq25703_volatile_regs = {
+	.yes_ranges = bq25703_volatile_reg_ranges,
+	.n_yes_ranges = ARRAY_SIZE(bq25703_volatile_reg_ranges),
+};
+
+static const struct regmap_config bq25703_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+	.max_register = BQ25703_ADC_OPTION,
+	.cache_type = REGCACHE_RBTREE,
+	.wr_table = &bq25703_writeable_regs,
+	.volatile_table = &bq25703_volatile_regs,
+	.val_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+static const struct mfd_cell bq25703_cells[] = {
+	MFD_CELL_NAME("bq257xx-regulator"),
+	MFD_CELL_NAME("bq257xx-charger"),
+};
+
+static int bq257xx_probe(struct i2c_client *client)
+{
+	struct bq257xx_device *ddata;
+	const struct mfd_cell *cells;
+	int nr_cells;
+	int ret;
+
+	ddata = devm_kzalloc(&client->dev, sizeof(*ddata), GFP_KERNEL);
+	if (!ddata)
+		return -ENOMEM;
+
+	ddata->client = client;
+
+	cells = bq25703_cells;
+	nr_cells = ARRAY_SIZE(bq25703_cells);
+	ddata->regmap = devm_regmap_init_i2c(client, &bq25703_regmap_config);
+	if (IS_ERR(ddata->regmap)) {
+		dev_err(&client->dev, "Failed to allocate register map\n");
+		return PTR_ERR(ddata->regmap);
+	}
+
+	i2c_set_clientdata(client, ddata);
+
+	ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_AUTO,
+				   cells, nr_cells, NULL, 0, NULL);
+	if (ret) {
+		dev_err(&client->dev, "Failed to register child devices %d\n", ret);
+		return ret;
+	}
+
+	return ret;
+}
+
+static const struct i2c_device_id bq257xx_i2c_ids[] = {
+	{ "bq25703a" },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, bq257xx_i2c_ids);
+
+static const struct of_device_id bq257xx_of_match[] = {
+	{ .compatible = "ti,bq25703a" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, bq257xx_of_match);
+
+static struct i2c_driver bq257xx_driver = {
+	.driver = {
+		.name = "bq257xx",
+		.of_match_table = bq257xx_of_match,
+	},
+	.probe = bq257xx_probe,
+	.id_table = bq257xx_i2c_ids,
+};
+module_i2c_driver(bq257xx_driver);
+
+MODULE_DESCRIPTION("bq257xx buck/boost/charger driver");
+MODULE_AUTHOR("Chris Morgan <macromorgan@hotmail.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/bq257xx.h b/include/linux/mfd/bq257xx.h
new file mode 100644
index 000000000000..153a96248f32
--- /dev/null
+++ b/include/linux/mfd/bq257xx.h
@@ -0,0 +1,108 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Register definitions for TI BQ257XX
+ * Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#define BQ25703_CHARGE_OPTION_0			0x00
+#define BQ25703_CHARGE_CURRENT			0x02
+#define BQ25703_MAX_CHARGE_VOLT			0x04
+#define BQ25703_OTG_VOLT			0x06
+#define BQ25703_OTG_CURRENT			0x08
+#define BQ25703_INPUT_VOLTAGE			0x0a
+#define BQ25703_MIN_VSYS			0x0c
+#define BQ25703_IIN_HOST			0x0e
+#define BQ25703_CHARGER_STATUS			0x20
+#define BQ25703_PROCHOT_STATUS			0x22
+#define BQ25703_IIN_DPM				0x24
+#define BQ25703_ADCIBAT_CHG			0x28
+#define BQ25703_ADCIINCMPIN			0x2a
+#define BQ25703_ADCVSYSVBAT			0x2c
+#define BQ25703_MANUFACT_DEV_ID			0x2e
+#define BQ25703_CHARGE_OPTION_1			0x30
+#define BQ25703_CHARGE_OPTION_2			0x32
+#define BQ25703_CHARGE_OPTION_3			0x34
+#define BQ25703_ADC_OPTION			0x3a
+
+#define BQ25703_EN_LWPWR			BIT(15)
+#define BQ25703_WDTMR_ADJ_MASK			GENMASK(14, 13)
+#define BQ25703_WDTMR_DISABLE			0
+#define BQ25703_WDTMR_5_SEC			1
+#define BQ25703_WDTMR_88_SEC			2
+#define BQ25703_WDTMR_175_SEC			3
+
+#define BQ25703_ICHG_MASK			GENMASK(12, 6)
+#define BQ25703_ICHG_STEP_UA			64000
+#define BQ25703_ICHG_MIN_UA			64000
+#define BQ25703_ICHG_MAX_UA			8128000
+
+#define BQ25703_MAX_CHARGE_VOLT_MASK		GENMASK(15, 4)
+#define BQ25703_VBATREG_STEP_UV			16000
+#define BQ25703_VBATREG_MIN_UV			1024000
+#define BQ25703_VBATREG_MAX_UV			19200000
+
+#define BQ25703_OTG_VOLT_MASK			GENMASK(13, 6)
+#define BQ25703_OTG_VOLT_STEP_UV		64000
+#define BQ25703_OTG_VOLT_MIN_UV			4480000
+#define BQ25703_OTG_VOLT_MAX_UV			20800000
+#define BQ25703_OTG_VOLT_NUM_VOLT		256
+
+#define BQ25703_OTG_CUR_MASK			GENMASK(14, 8)
+#define BQ25703_OTG_CUR_STEP_UA			50000
+#define BQ25703_OTG_CUR_MAX_UA			6350000
+
+#define BQ25703_MINVSYS_MASK			GENMASK(13, 8)
+#define BQ25703_MINVSYS_STEP_UV			256000
+#define BQ25703_MINVSYS_MIN_UV			1024000
+#define BQ25703_MINVSYS_MAX_UV			16128000
+
+#define BQ25703_STS_AC_STAT			BIT(15)
+#define BQ25703_STS_IN_FCHRG			BIT(10)
+#define BQ25703_STS_IN_PCHRG			BIT(9)
+#define BQ25703_STS_FAULT_ACOV			BIT(7)
+#define BQ25703_STS_FAULT_BATOC			BIT(6)
+#define BQ25703_STS_FAULT_ACOC			BIT(5)
+
+#define BQ25703_IINDPM_MASK			GENMASK(14, 8)
+#define BQ25703_IINDPM_STEP_UA			50000
+#define BQ25703_IINDPM_MIN_UA			50000
+#define BQ25703_IINDPM_MAX_UA			6400000
+#define BQ25703_IINDPM_DEFAULT_UA		3300000
+#define BQ25703_IINDPM_OFFSET_UA		50000
+
+#define BQ25703_ADCIBAT_DISCHG_MASK		GENMASK(6, 0)
+#define BQ25703_ADCIBAT_CHG_MASK		GENMASK(14, 8)
+#define BQ25703_ADCIBAT_CHG_STEP_UA		64000
+#define BQ25703_ADCIBAT_DIS_STEP_UA		256000
+
+#define BQ25703_ADCIIN				GENMASK(15, 8)
+#define BQ25703_ADCIINCMPIN_STEP		50000
+
+#define BQ25703_ADCVSYS_MASK			GENMASK(15, 8)
+#define BQ25703_ADCVBAT_MASK			GENMASK(7, 0)
+#define BQ25703_ADCVSYSVBAT_OFFSET_UV		2880000
+#define BQ25703_ADCVSYSVBAT_STEP		64000
+
+#define BQ25703_ADC_CH_MASK			GENMASK(7, 0)
+#define BQ25703_ADC_CONV_EN			BIT(15)
+#define BQ25703_ADC_START			BIT(14)
+#define BQ25703_ADC_FULL_SCALE			BIT(13)
+#define BQ25703_ADC_CMPIN_EN			BIT(7)
+#define BQ25703_ADC_VBUS_EN			BIT(6)
+#define BQ25703_ADC_PSYS_EN			BIT(5)
+#define BQ25703_ADC_IIN_EN			BIT(4)
+#define BQ25703_ADC_IDCHG_EN			BIT(3)
+#define BQ25703_ADC_ICHG_EN			BIT(2)
+#define BQ25703_ADC_VSYS_EN			BIT(1)
+#define BQ25703_ADC_VBAT_EN			BIT(0)
+
+#define BQ25703_EN_OTG_MASK			BIT(12)
+
+enum bq257xx_id {
+	BQ25703A,
+};
+
+struct bq257xx_device {
+	struct i2c_client *client;
+	struct regmap *regmap;
+};
-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH V4 3/5] power: supply: bq257xx: Add support for BQ257XX charger

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the charger function of the BQ257XX. The device is
capable of charging batteries with a layout of 1 to 4 cells in
series.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 drivers/power/supply/Kconfig           |   7 +
 drivers/power/supply/Makefile          |   1 +
 drivers/power/supply/bq257xx_charger.c | 754 +++++++++++++++++++++++++
 3 files changed, 762 insertions(+)
 create mode 100644 drivers/power/supply/bq257xx_charger.c

diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 79ddb006e2da..11893c50c5d2 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -767,6 +767,13 @@ config CHARGER_BQ2515X
 	  rail, ADC for battery and system monitoring, and push-button
 	  controller.
 
+config CHARGER_BQ257XX
+	tristate "TI BQ257XX battery charger family"
+	depends on MFD_BQ257XX
+	help
+	  Say Y to enable support for the TI BQ257XX family of battery
+	  charging integrated circuits.
+
 config CHARGER_BQ25890
 	tristate "TI BQ25890 battery charger driver"
 	depends on I2C
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 4f5f8e3507f8..425caeb31fc2 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -97,6 +97,7 @@ obj-$(CONFIG_CHARGER_BQ24190)	+= bq24190_charger.o
 obj-$(CONFIG_CHARGER_BQ24257)	+= bq24257_charger.o
 obj-$(CONFIG_CHARGER_BQ24735)	+= bq24735-charger.o
 obj-$(CONFIG_CHARGER_BQ2515X)	+= bq2515x_charger.o
+obj-$(CONFIG_CHARGER_BQ257XX)	+= bq257xx_charger.o
 obj-$(CONFIG_CHARGER_BQ25890)	+= bq25890_charger.o
 obj-$(CONFIG_CHARGER_BQ25980)	+= bq25980_charger.o
 obj-$(CONFIG_CHARGER_BQ256XX)	+= bq256xx_charger.o
diff --git a/drivers/power/supply/bq257xx_charger.c b/drivers/power/supply/bq257xx_charger.c
new file mode 100644
index 000000000000..749c471eccb1
--- /dev/null
+++ b/drivers/power/supply/bq257xx_charger.c
@@ -0,0 +1,754 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * BQ257XX Battery Charger Driver
+ * Copyright (C) 2024 Chris Morgan <macromorgan@hotmail.com>
+ * Based off of BQ256XX Battery Charger Driver
+ * Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#include <linux/bitfield.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/bq257xx.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+
+/* Forward declaration of driver data. */
+struct bq257xx_chg;
+
+/**
+ * struct bq257xx_chip_info - chip specific routines
+ * @bq257xx_hw_init: init function for hw
+ * @bq257xx_hw_shutdown: shutdown function for hw
+ * @bq257xx_get_state: get and update state of hardware
+ * @bq257xx_set_ichg: set maximum charge current (in uA)
+ * @bq257xx_set_vbatreg: set maximum charge voltage (in uV)
+ * @bq257xx_set_iindpm: set maximum input current (in uA)
+ */
+struct bq257xx_chip_info {
+	int (*bq257xx_hw_init)(struct bq257xx_chg *pdata);
+	void (*bq257xx_hw_shutdown)(struct bq257xx_chg *pdata);
+	int (*bq257xx_get_state)(struct bq257xx_chg *pdata);
+	int (*bq257xx_set_ichg)(struct bq257xx_chg *pdata, int ichg);
+	int (*bq257xx_set_vbatreg)(struct bq257xx_chg *pdata, int vbatreg);
+	int (*bq257xx_set_iindpm)(struct bq257xx_chg *pdata, int iindpm);
+};
+
+/**
+ * struct bq257xx_chg - driver data for charger
+ * @chip: hw specific functions
+ * @bq: parent MFD device
+ * @charger: power supply device
+ * @online: charger input is present
+ * @fast_charge: charger is in fast charge mode
+ * @pre_charge: charger is in pre-charge mode
+ * @ov_fault: charger reports over voltage fault
+ * @batoc_fault: charger reports battery over current fault
+ * @oc_fault: charger reports over current fault
+ * @usb_type: USB type reported from parent power supply
+ * @supplied: Status of parent power supply
+ * @iindpm_max: maximum input current limit (uA)
+ * @vbat_max: maximum charge voltage (uV)
+ * @ichg_max: maximum charge current (uA)
+ * @vsys_min: minimum system voltage (uV)
+ */
+struct bq257xx_chg {
+	const struct bq257xx_chip_info *chip;
+	struct bq257xx_device *bq;
+	struct power_supply *charger;
+	bool online;
+	bool fast_charge;
+	bool pre_charge;
+	bool ov_fault;
+	bool batoc_fault;
+	bool oc_fault;
+	int usb_type;
+	int supplied;
+	u32 iindpm_max;
+	u32 vbat_max;
+	u32 ichg_max;
+	u32 vsys_min;
+};
+
+/**
+ * bq25703_get_state() - Get the current state of the device
+ * @pdata: driver platform data
+ *
+ * Get the current state of the charger. Check if the charger is
+ * powered, what kind of charge state (if any) the device is in,
+ * and if there are any active faults.
+ *
+ * Return: Returns 0 on success, or error on failure to read device.
+ */
+static int bq25703_get_state(struct bq257xx_chg *pdata)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_CHARGER_STATUS, &reg);
+	if (ret)
+		return ret;
+
+	pdata->online = reg & BQ25703_STS_AC_STAT;
+	pdata->fast_charge = reg & BQ25703_STS_IN_FCHRG;
+	pdata->pre_charge = reg & BQ25703_STS_IN_PCHRG;
+	pdata->ov_fault = reg & BQ25703_STS_FAULT_ACOV;
+	pdata->batoc_fault = reg & BQ25703_STS_FAULT_BATOC;
+	pdata->oc_fault = reg & BQ25703_STS_FAULT_ACOC;
+
+	return 0;
+}
+
+/**
+ * bq25703_get_min_vsys() - Get the minimum system voltage
+ * @pdata: driver platform data
+ * @intval: value for minimum voltage
+ *
+ * Return: Returns 0 on success or error on failure to read.
+ */
+static int bq25703_get_min_vsys(struct bq257xx_chg *pdata, int *intval)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_MIN_VSYS,
+			  &reg);
+	if (ret)
+		return ret;
+
+	reg = FIELD_GET(BQ25703_MINVSYS_MASK, reg);
+	*intval = (reg * BQ25703_MINVSYS_STEP_UV) + BQ25703_MINVSYS_MIN_UV;
+
+	return ret;
+}
+
+/**
+ * bq25703_set_min_vsys() - Set the minimum system voltage
+ * @pdata: driver platform data
+ * @vsys: voltage value to set in uV.
+ *
+ * This function takes a requested minimum system voltage value, clamps
+ * it between the minimum supported value by the charger and a user
+ * defined minimum system value, and then writes the value to the
+ * appropriate register.
+ *
+ * Return: Returns 0 on success or error if an error occurs.
+ */
+static int bq25703_set_min_vsys(struct bq257xx_chg *pdata, int vsys)
+{
+	unsigned int reg;
+	int vsys_min = pdata->vsys_min;
+
+	vsys = clamp(vsys, BQ25703_MINVSYS_MIN_UV, vsys_min);
+	reg = ((vsys - BQ25703_MINVSYS_MIN_UV) / BQ25703_MINVSYS_STEP_UV);
+	reg = FIELD_PREP(BQ25703_MINVSYS_MASK, reg);
+
+	return regmap_write(pdata->bq->regmap, BQ25703_MIN_VSYS,
+			    reg);
+}
+
+/**
+ * bq25703_get_cur() - Get the reported current from the battery
+ * @pdata: driver platform data
+ * @intval: value of reported battery current
+ *
+ * Read the reported current from the battery. Since value is always
+ * positive set sign to negative if discharging.
+ *
+ * Return: Returns 0 on success or error if unable to read value.
+ */
+static int bq25703_get_cur(struct bq257xx_chg *pdata, int *intval)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_ADCIBAT_CHG, &reg);
+	if (ret < 0)
+		return ret;
+
+	if (pdata->online)
+		*intval = FIELD_GET(BQ25703_ADCIBAT_CHG_MASK, reg) *
+			  BQ25703_ADCIBAT_CHG_STEP_UA;
+	else
+		*intval = -(FIELD_GET(BQ25703_ADCIBAT_DISCHG_MASK, reg) *
+			    BQ25703_ADCIBAT_DIS_STEP_UA);
+
+	return ret;
+}
+
+/**
+ * bq25703_get_ichg_cur() - Get the maximum reported charge current
+ * @pdata: driver platform data
+ * @intval: value of maximum reported charge current
+ *
+ * Get the maximum reported charge current from the battery.
+ *
+ * Return: Returns 0 on success or error if unable to read value.
+ */
+static int bq25703_get_ichg_cur(struct bq257xx_chg *pdata, int *intval)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_CHARGE_CURRENT, &reg);
+	if (ret)
+		return ret;
+
+	*intval = FIELD_GET(BQ25703_ICHG_MASK, reg) * BQ25703_ICHG_STEP_UA;
+
+	return ret;
+}
+
+/**
+ * bq25703_set_ichg_cur() - Set the maximum charge current
+ * @pdata: driver platform data
+ * @ichg: current value to set in uA.
+ *
+ * This function takes a requested maximum charge current value, clamps
+ * it between the minimum supported value by the charger and a user
+ * defined maximum charging value, and then writes the value to the
+ * appropriate register.
+ *
+ * Return: Returns 0 on success or error if an error occurs.
+ */
+static int bq25703_set_ichg_cur(struct bq257xx_chg *pdata, int ichg)
+{
+	unsigned int reg;
+	int ichg_max = pdata->ichg_max;
+
+	ichg = clamp(ichg, BQ25703_ICHG_MIN_UA, ichg_max);
+	reg = FIELD_PREP(BQ25703_ICHG_MASK, (ichg / BQ25703_ICHG_STEP_UA));
+
+	return regmap_write(pdata->bq->regmap, BQ25703_CHARGE_CURRENT,
+			    reg);
+}
+
+/**
+ * bq25703_get_chrg_volt() - Get the maximum set charge voltage
+ * @pdata: driver platform data
+ * @intval: maximum charge voltage value
+ *
+ * Return: Returns 0 on success or error if unable to read value.
+ */
+static int bq25703_get_chrg_volt(struct bq257xx_chg *pdata, int *intval)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_MAX_CHARGE_VOLT,
+			  &reg);
+	if (ret)
+		return ret;
+
+	*intval = FIELD_GET(BQ25703_MAX_CHARGE_VOLT_MASK, reg) *
+		  BQ25703_VBATREG_STEP_UV;
+
+	return ret;
+}
+
+/**
+ * bq25703_set_chrg_volt() - Set the maximum charge voltage
+ * @pdata: driver platform data
+ * @vbat: voltage value to set in uV.
+ *
+ * This function takes a requested maximum charge voltage value, clamps
+ * it between the minimum supported value by the charger and a user
+ * defined maximum charging value, and then writes the value to the
+ * appropriate register.
+ *
+ * Return: Returns 0 on success or error if an error occurs.
+ */
+static int bq25703_set_chrg_volt(struct bq257xx_chg *pdata, int vbat)
+{
+	unsigned int reg;
+	int vbat_max = pdata->vbat_max;
+
+	vbat = clamp(vbat, BQ25703_VBATREG_MIN_UV, vbat_max);
+
+	reg = FIELD_PREP(BQ25703_MAX_CHARGE_VOLT_MASK,
+			 (vbat / BQ25703_VBATREG_STEP_UV));
+
+	return regmap_write(pdata->bq->regmap, BQ25703_MAX_CHARGE_VOLT,
+			    reg);
+}
+
+/**
+ * bq25703_get_iindpm() - Get the maximum set input current
+ * @pdata: driver platform data
+ * @intval: maximum input current value
+ *
+ * Read the actual input current limit from the device into intval.
+ * This can differ from the value programmed due to some autonomous
+ * functions that may be enabled (but are not currently). This is why
+ * there is a different register used.
+ *
+ * Return: Returns 0 on success or error if unable to read register
+ * value.
+ */
+static int bq25703_get_iindpm(struct bq257xx_chg *pdata, int *intval)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_IIN_DPM, &reg);
+	if (ret)
+		return ret;
+
+	reg = FIELD_GET(BQ25703_IINDPM_MASK, reg);
+	*intval = (reg * BQ25703_IINDPM_STEP_UA) + BQ25703_IINDPM_OFFSET_UA;
+
+	return ret;
+}
+
+/**
+ * bq25703_set_iindpm() - Set the maximum input current
+ * @pdata: driver platform data
+ * @iindpm: current value in uA.
+ *
+ * This function takes a requested maximum input current value, clamps
+ * it between the minimum supported value by the charger and a user
+ * defined maximum input value, and then writes the value to the
+ * appropriate register.
+ *
+ * Return: Returns 0 on success or error if an error occurs.
+ */
+static int bq25703_set_iindpm(struct bq257xx_chg *pdata, int iindpm)
+{
+	unsigned int reg;
+	int iindpm_max = pdata->iindpm_max;
+
+	iindpm = clamp(iindpm, BQ25703_IINDPM_MIN_UA, iindpm_max);
+
+	reg = ((iindpm - BQ25703_IINDPM_OFFSET_UA) / BQ25703_IINDPM_STEP_UA);
+
+	return regmap_write(pdata->bq->regmap, BQ25703_IIN_HOST,
+			    FIELD_PREP(BQ25703_IINDPM_MASK, reg));
+}
+
+/**
+ * bq25703_get_vbat() - Get the reported voltage from the battery
+ * @pdata: driver platform data
+ * @intval: value of reported battery voltage
+ *
+ * Read value of battery voltage into intval.
+ *
+ * Return: Returns 0 on success or error if unable to read value.
+ */
+static int bq25703_get_vbat(struct bq257xx_chg *pdata, int *intval)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_ADCVSYSVBAT, &reg);
+	if (ret)
+		return ret;
+
+	reg = FIELD_GET(BQ25703_ADCVBAT_MASK, reg);
+	*intval = (reg * BQ25703_ADCVSYSVBAT_STEP) + BQ25703_ADCVSYSVBAT_OFFSET_UV;
+
+	return ret;
+}
+
+/**
+ * bq25703_hw_init() - Set all the required registers to init the charger
+ * @pdata: driver platform data
+ *
+ * Initialize the BQ25703 by first disabling the watchdog timer (which
+ * shuts off the charger in the absence of periodic writes). Then, set
+ * the charge current, charge voltage, minimum system voltage, and
+ * input current limit. Disable low power mode to allow ADCs and
+ * interrupts. Enable the ADC, start the ADC, set the ADC scale to
+ * full, and enable each individual ADC channel.
+ *
+ * Return: Returns 0 on success or error code on error.
+ */
+static int bq25703_hw_init(struct bq257xx_chg *pdata)
+{
+	struct regmap *regmap = pdata->bq->regmap;
+	int ret = 0;
+
+	regmap_update_bits(regmap, BQ25703_CHARGE_OPTION_0,
+			   BQ25703_WDTMR_ADJ_MASK,
+			   FIELD_PREP(BQ25703_WDTMR_ADJ_MASK,
+			   BQ25703_WDTMR_DISABLE));
+
+	ret = pdata->chip->bq257xx_set_ichg(pdata, pdata->ichg_max);
+	if (ret)
+		return ret;
+
+	ret = pdata->chip->bq257xx_set_vbatreg(pdata, pdata->vbat_max);
+	if (ret)
+		return ret;
+
+	ret = bq25703_set_min_vsys(pdata, pdata->vsys_min);
+	if (ret)
+		return ret;
+
+	ret = pdata->chip->bq257xx_set_iindpm(pdata, pdata->iindpm_max);
+	if (ret)
+		return ret;
+
+	regmap_update_bits(regmap, BQ25703_CHARGE_OPTION_0,
+			   BQ25703_EN_LWPWR, !BQ25703_EN_LWPWR);
+
+	regmap_update_bits(regmap, BQ25703_ADC_OPTION,
+			   BQ25703_ADC_CONV_EN, BQ25703_ADC_CONV_EN);
+
+	regmap_update_bits(regmap, BQ25703_ADC_OPTION,
+			   BQ25703_ADC_START, BQ25703_ADC_START);
+
+	regmap_update_bits(regmap, BQ25703_ADC_OPTION,
+			   BQ25703_ADC_FULL_SCALE, BQ25703_ADC_FULL_SCALE);
+
+	regmap_update_bits(regmap, BQ25703_ADC_OPTION,
+			   BQ25703_ADC_CH_MASK,
+			   (BQ25703_ADC_CMPIN_EN | BQ25703_ADC_VBUS_EN |
+			   BQ25703_ADC_PSYS_EN | BQ25703_ADC_IIN_EN |
+			   BQ25703_ADC_IDCHG_EN | BQ25703_ADC_ICHG_EN |
+			   BQ25703_ADC_VSYS_EN | BQ25703_ADC_VBAT_EN));
+
+	return ret;
+}
+
+/**
+ * bq25703_hw_shutdown() - Set registers for shutdown
+ * @pdata: driver platform data
+ *
+ * Enable low power mode for the device while in shutdown.
+ */
+static void bq25703_hw_shutdown(struct bq257xx_chg *pdata)
+{
+	regmap_update_bits(pdata->bq->regmap, BQ25703_CHARGE_OPTION_0,
+			   BQ25703_EN_LWPWR, BQ25703_EN_LWPWR);
+}
+
+static int bq257xx_set_charger_property(struct power_supply *psy,
+		enum power_supply_property prop,
+		const union power_supply_propval *val)
+{
+	struct bq257xx_chg *pdata = power_supply_get_drvdata(psy);
+
+	switch (prop) {
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return pdata->chip->bq257xx_set_iindpm(pdata, val->intval);
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
+		return pdata->chip->bq257xx_set_vbatreg(pdata, val->intval);
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+		return pdata->chip->bq257xx_set_ichg(pdata, val->intval);
+
+	default:
+		break;
+	}
+
+	return -EINVAL;
+}
+
+static int bq257xx_get_charger_property(struct power_supply *psy,
+				enum power_supply_property psp,
+				union power_supply_propval *val)
+{
+	struct bq257xx_chg *pdata = power_supply_get_drvdata(psy);
+	int ret = 0;
+
+	ret = pdata->chip->bq257xx_get_state(pdata);
+	if (ret)
+		return ret;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		if (!pdata->online)
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		else if (pdata->fast_charge || pdata->pre_charge)
+			val->intval = POWER_SUPPLY_STATUS_CHARGING;
+		else
+			val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		break;
+
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (pdata->ov_fault || pdata->batoc_fault)
+			val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+		else if (pdata->oc_fault)
+			val->intval = POWER_SUPPLY_HEALTH_OVERCURRENT;
+		else
+			val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = "Texas Instruments";
+		break;
+
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = pdata->online;
+		break;
+
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return bq25703_get_iindpm(pdata, &val->intval);
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
+		return bq25703_get_chrg_volt(pdata, &val->intval);
+
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		return bq25703_get_cur(pdata, &val->intval);
+
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		return bq25703_get_vbat(pdata, &val->intval);
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+		return bq25703_get_ichg_cur(pdata, &val->intval);
+
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
+		return bq25703_get_min_vsys(pdata, &val->intval);
+
+	case POWER_SUPPLY_PROP_USB_TYPE:
+		val->intval = pdata->usb_type;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+static enum power_supply_property bq257xx_power_supply_props[] = {
+	POWER_SUPPLY_PROP_MANUFACTURER,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
+	POWER_SUPPLY_PROP_VOLTAGE_MIN,
+	POWER_SUPPLY_PROP_USB_TYPE,
+};
+
+static int bq257xx_property_is_writeable(struct power_supply *psy,
+					 enum power_supply_property prop)
+{
+	switch (prop) {
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+/**
+ * bq257xx_external_power_changed() - Handler for external power change
+ * @psy: Power supply data
+ *
+ * When the external power into the charger is changed, check the USB
+ * type so that it can be reported. Additionally, update the max input
+ * current and max charging current to the value reported if it is a
+ * USB PD charger, otherwise use the default value. Note that each time
+ * a charger is removed the max charge current register is erased, so
+ * it must be set again each time the input changes or the device will
+ * not charge.
+ */
+static void bq257xx_external_power_changed(struct power_supply *psy)
+{
+	struct bq257xx_chg *pdata = power_supply_get_drvdata(psy);
+	union power_supply_propval val;
+	int ret;
+	int imax = pdata->iindpm_max;
+
+	pdata->chip->bq257xx_get_state(pdata);
+
+	pdata->supplied = power_supply_am_i_supplied(pdata->charger);
+	if (pdata->supplied < 0)
+		return;
+
+	if (pdata->supplied == 0)
+		goto out;
+
+	ret = power_supply_get_property_from_supplier(psy,
+						      POWER_SUPPLY_PROP_USB_TYPE,
+						      &val);
+	if (ret)
+		return;
+
+	pdata->usb_type = val.intval;
+
+	if ((pdata->usb_type == POWER_SUPPLY_USB_TYPE_PD) ||
+	    (pdata->usb_type == POWER_SUPPLY_USB_TYPE_PD_DRP) ||
+	    (pdata->usb_type == POWER_SUPPLY_USB_TYPE_PD_PPS)) {
+		ret = power_supply_get_property_from_supplier(psy,
+							      POWER_SUPPLY_PROP_CURRENT_MAX,
+							      &val);
+		if (ret)
+			return;
+
+		if (val.intval)
+			imax = val.intval;
+	}
+
+	if (pdata->supplied) {
+		pdata->chip->bq257xx_set_ichg(pdata, pdata->ichg_max);
+		pdata->chip->bq257xx_set_iindpm(pdata, imax);
+		pdata->chip->bq257xx_set_vbatreg(pdata, pdata->vbat_max);
+	}
+
+out:
+	power_supply_changed(psy);
+}
+
+static irqreturn_t bq257xx_irq_handler_thread(int irq, void *private)
+{
+	struct bq257xx_chg *pdata = private;
+
+	bq257xx_external_power_changed(pdata->charger);
+	return IRQ_HANDLED;
+}
+
+static const struct power_supply_desc bq257xx_power_supply_desc = {
+	.name = "bq257xx-charger",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.usb_types = BIT(POWER_SUPPLY_USB_TYPE_C) |
+		     BIT(POWER_SUPPLY_USB_TYPE_PD) |
+		     BIT(POWER_SUPPLY_USB_TYPE_PD_DRP) |
+		     BIT(POWER_SUPPLY_USB_TYPE_PD_PPS) |
+		     BIT(POWER_SUPPLY_USB_TYPE_UNKNOWN),
+	.properties = bq257xx_power_supply_props,
+	.num_properties = ARRAY_SIZE(bq257xx_power_supply_props),
+	.get_property = bq257xx_get_charger_property,
+	.set_property = bq257xx_set_charger_property,
+	.property_is_writeable = bq257xx_property_is_writeable,
+	.external_power_changed = bq257xx_external_power_changed,
+};
+
+static const struct bq257xx_chip_info bq25703_chip_info = {
+		.bq257xx_hw_init = &bq25703_hw_init,
+		.bq257xx_hw_shutdown = &bq25703_hw_shutdown,
+		.bq257xx_get_state = &bq25703_get_state,
+		.bq257xx_set_ichg = &bq25703_set_ichg_cur,
+		.bq257xx_set_vbatreg = &bq25703_set_chrg_volt,
+		.bq257xx_set_iindpm = &bq25703_set_iindpm,
+};
+
+/**
+ * bq257xx_parse_dt() - Parse the device tree for required properties
+ * @pdata: driver platform data
+ * @psy_cfg: power supply config data
+ * @dev: device struct
+ *
+ * Read the device tree to identify the minimum system voltage, the
+ * maximum charge current, the maximum charge voltage, and the maximum
+ * input current.
+ *
+ * Return: Returns 0 on success or error code on error.
+ */
+static int bq257xx_parse_dt(struct bq257xx_chg *pdata,
+		struct power_supply_config *psy_cfg, struct device *dev)
+{
+	struct power_supply_battery_info *bat_info;
+	int ret;
+
+	ret = power_supply_get_battery_info(pdata->charger,
+					    &bat_info);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Unable to get battery info\n");
+
+	if ((bat_info->voltage_min_design_uv <= 0) ||
+	    (bat_info->constant_charge_voltage_max_uv <= 0) ||
+	    (bat_info->constant_charge_current_max_ua <= 0))
+		return dev_err_probe(dev, -EINVAL,
+				     "Required bat info missing or invalid\n");
+
+	pdata->vsys_min = bat_info->voltage_min_design_uv;
+	pdata->vbat_max = bat_info->constant_charge_voltage_max_uv;
+	pdata->ichg_max = bat_info->constant_charge_current_max_ua;
+
+	power_supply_put_battery_info(pdata->charger, bat_info);
+
+	ret = device_property_read_u32(dev,
+				       "input-current-limit-microamp",
+				       &pdata->iindpm_max);
+	if (ret)
+		pdata->iindpm_max = BQ25703_IINDPM_DEFAULT_UA;
+
+	return 0;
+}
+
+static int bq257xx_charger_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct bq257xx_device *bq = dev_get_drvdata(pdev->dev.parent);
+	struct bq257xx_chg *pdata;
+	struct power_supply_config psy_cfg = { };
+	int ret;
+
+	device_set_of_node_from_dev(dev, pdev->dev.parent);
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->bq = bq;
+	pdata->chip = &bq25703_chip_info;
+
+	platform_set_drvdata(pdev, pdata);
+
+	psy_cfg.drv_data = pdata;
+	psy_cfg.fwnode = dev_fwnode(dev);
+
+	pdata->charger = devm_power_supply_register(dev,
+						    &bq257xx_power_supply_desc,
+						    &psy_cfg);
+	if (IS_ERR(pdata->charger))
+		return dev_err_probe(dev, PTR_ERR(pdata->charger),
+				     "Power supply register charger failed\n");
+
+	ret = bq257xx_parse_dt(pdata, &psy_cfg, dev);
+	if (ret)
+		return ret;
+
+	ret = pdata->chip->bq257xx_hw_init(pdata);
+	if (ret)
+		return dev_err_probe(dev, ret, "Cannot initialize the charger\n");
+
+	platform_set_drvdata(pdev, pdata);
+
+	if (bq->client->irq) {
+		ret = devm_request_threaded_irq(dev, bq->client->irq, NULL,
+						bq257xx_irq_handler_thread,
+						IRQF_TRIGGER_RISING |
+						IRQF_TRIGGER_FALLING |
+						IRQF_ONESHOT,
+						dev_name(&bq->client->dev), pdata);
+		if (ret < 0) {
+			dev_err(dev, "get irq fail: %d\n", ret);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static void bq257xx_charger_shutdown(struct platform_device *pdev)
+{
+	struct bq257xx_chg *pdata = platform_get_drvdata(pdev);
+
+	pdata->chip->bq257xx_hw_shutdown(pdata);
+}
+
+static struct platform_driver bq257xx_chg_driver = {
+	.driver = {
+		.name = "bq257xx-charger",
+	},
+	.probe = bq257xx_charger_probe,
+	.shutdown = bq257xx_charger_shutdown,
+};
+module_platform_driver(bq257xx_chg_driver);
+
+MODULE_DESCRIPTION("bq257xx charger driver");
+MODULE_AUTHOR("Chris Morgan <macromorgan@hotmail.com>");
+MODULE_LICENSE("GPL");
-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH V4 4/5] regulator: bq257xx: Add bq257xx boost regulator driver

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the boost regulator found in the Texas Instruments
BQ25703. The boost regulator is capable of outputting between 4.48
and 20.8 volts and between 0 and 6.35 amps.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/Kconfig             |   8 ++
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/bq257xx-regulator.c | 189 ++++++++++++++++++++++++++
 3 files changed, 198 insertions(+)
 create mode 100644 drivers/regulator/bq257xx-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 6d8988387da4..53cd33afe6d5 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -297,6 +297,14 @@ config REGULATOR_BD96801
 	  This driver can also be built as a module. If so, the module
 	  will be called bd96801-regulator.
 
+config REGULATOR_BQ257XX
+	tristate "TI BQ257XX regulator family"
+	depends on MFD_BQ257XX
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  Say Y to enable support for the boost regulator function of
+	  the BQ257XX family of charger circuits.
+
 config REGULATOR_CPCAP
 	tristate "Motorola CPCAP regulator"
 	depends on MFD_CPCAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index c0bc7a0f4e67..d6024189a248 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_REGULATOR_BD71828) += bd71828-regulator.o
 obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_BD957XMUF) += bd9576-regulator.o
+obj-$(CONFIG_REGULATOR_BQ257XX) += bq257xx-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x-regulator.o
 obj-$(CONFIG_REGULATOR_BD96801) += bd96801-regulator.o
 obj-$(CONFIG_REGULATOR_DA9052)	+= da9052-regulator.o
diff --git a/drivers/regulator/bq257xx-regulator.c b/drivers/regulator/bq257xx-regulator.c
new file mode 100644
index 000000000000..5ccead8e0cfb
--- /dev/null
+++ b/drivers/regulator/bq257xx-regulator.c
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0
+/* BQ257XX Battery Charger Driver
+ * Copyright (C) 2024 Chris Morgan <macromorgan@hotmail.com>
+ * Based off of BQ256XX Battery Charger driver and
+ * RK808 Regulator driver.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mfd/bq257xx.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+struct bq257xx_reg_data {
+	struct bq257xx_device *bq;
+	struct regulator_dev *bq257xx_reg;
+	struct gpio_desc *otg_en_gpio;
+	struct regulator_desc desc;
+};
+
+static int bq25703_vbus_get_cur_limit(struct regulator_dev *rdev)
+{
+	struct bq257xx_reg_data *pdata = rdev_get_drvdata(rdev);
+	int ret;
+	unsigned int reg;
+
+	ret = regmap_read(pdata->bq->regmap, BQ25703_OTG_CURRENT, &reg);
+	if (ret)
+		return ret;
+	return FIELD_GET(BQ25703_OTG_CUR_MASK, reg) * BQ25703_OTG_CUR_STEP_UA;
+}
+
+/*
+ * Check if the minimum current and maximum current requested are
+ * sane values, then set the register accordingly.
+ */
+static int bq25703_vbus_set_cur_limit(struct regulator_dev *rdev,
+				      int min_uA, int max_uA)
+{
+	struct bq257xx_reg_data *pdata = rdev_get_drvdata(rdev);
+	unsigned int reg;
+
+	if ((min_uA > BQ25703_OTG_CUR_MAX_UA) || (max_uA < 0))
+		return -EINVAL;
+
+	reg = (max_uA / BQ25703_OTG_CUR_STEP_UA);
+
+	/* Catch rounding errors since our step is 50000uA. */
+	if ((reg * BQ25703_OTG_CUR_STEP_UA) < min_uA)
+		return -EINVAL;
+
+	return regmap_write(pdata->bq->regmap, BQ25703_OTG_CURRENT,
+			    FIELD_PREP(BQ25703_OTG_CUR_MASK, reg));
+}
+
+static int bq25703_vbus_enable(struct regulator_dev *rdev)
+{
+	struct bq257xx_reg_data *pdata = rdev_get_drvdata(rdev);
+
+	if (pdata->otg_en_gpio)
+		gpiod_set_value_cansleep(pdata->otg_en_gpio, 1);
+	return regulator_enable_regmap(rdev);
+}
+
+static int bq25703_vbus_disable(struct regulator_dev *rdev)
+{
+	struct bq257xx_reg_data *pdata = rdev_get_drvdata(rdev);
+
+	if (pdata->otg_en_gpio)
+		gpiod_set_value_cansleep(pdata->otg_en_gpio, 0);
+	return regulator_disable_regmap(rdev);
+}
+
+static const struct regulator_ops bq25703_vbus_ops = {
+	.enable = bq25703_vbus_enable,
+	.disable = bq25703_vbus_disable,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_current_limit = bq25703_vbus_get_cur_limit,
+	.set_current_limit = bq25703_vbus_set_cur_limit,
+};
+
+static const struct regulator_desc bq25703_vbus_desc = {
+	.name = "vbus",
+	.of_match = of_match_ptr("vbus"),
+	.regulators_node = of_match_ptr("regulators"),
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+	.ops = &bq25703_vbus_ops,
+	.min_uV = BQ25703_OTG_VOLT_MIN_UV,
+	.uV_step = BQ25703_OTG_VOLT_STEP_UV,
+	.n_voltages = BQ25703_OTG_VOLT_NUM_VOLT,
+	.enable_mask = BQ25703_EN_OTG_MASK,
+	.enable_reg = BQ25703_CHARGE_OPTION_3,
+	.enable_val = BQ25703_EN_OTG_MASK,
+	.disable_val = 0,
+	.vsel_reg = BQ25703_OTG_VOLT,
+	.vsel_mask = BQ25703_OTG_VOLT_MASK,
+};
+
+/* Get optional GPIO for OTG regulator enable. */
+static void bq257xx_reg_dt_parse_gpio(struct platform_device *pdev)
+{
+	struct device_node *child, *subchild;
+	struct bq257xx_reg_data *pdata = platform_get_drvdata(pdev);
+
+	child = of_get_child_by_name(pdev->dev.of_node,
+				     pdata->desc.regulators_node);
+	if (!child)
+		return;
+
+	subchild = of_get_child_by_name(child, pdata->desc.of_match);
+	if (!subchild)
+		return;
+
+	of_node_put(child);
+
+	pdata->otg_en_gpio = devm_fwnode_gpiod_get_index(&pdev->dev,
+							 of_fwnode_handle(subchild),
+							 "enable", 0,
+							 GPIOD_OUT_LOW,
+							 pdata->desc.of_match);
+
+	of_node_put(subchild);
+
+	if (IS_ERR_OR_NULL(pdata->otg_en_gpio)) {
+		dev_err(&pdev->dev, "Error getting enable gpio: %ld\n",
+			PTR_ERR(pdata->otg_en_gpio));
+		return;
+	}
+}
+
+static int bq257xx_regulator_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct bq257xx_device *bq = dev_get_drvdata(pdev->dev.parent);
+	struct bq257xx_reg_data *pdata;
+	struct device_node *np = dev->of_node;
+	struct regulator_init_data *init_data;
+	struct regulator_config cfg = {};
+
+	pdev->dev.of_node = pdev->dev.parent->of_node;
+	pdev->dev.of_node_reused = true;
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(struct bq257xx_reg_data), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->bq = bq;
+	pdata->desc = bq25703_vbus_desc;
+
+	platform_set_drvdata(pdev, pdata);
+	bq257xx_reg_dt_parse_gpio(pdev);
+
+	cfg.dev = &pdev->dev;
+	cfg.init_data = init_data;
+	cfg.driver_data = pdata;
+	cfg.of_node = np;
+	cfg.regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!cfg.regmap)
+		return -ENODEV;
+
+	pdata->bq257xx_reg = devm_regulator_register(dev, &pdata->desc, &cfg);
+	if (IS_ERR(pdata->bq257xx_reg)) {
+		return dev_err_probe(&pdev->dev, PTR_ERR(pdata->bq257xx_reg),
+				     "error registering bq257xx regulator");
+	}
+
+	return 0;
+}
+
+static struct platform_driver bq257xx_reg_driver = {
+	.driver = {
+		.name = "bq257xx-regulator",
+	},
+	.probe = bq257xx_regulator_probe,
+};
+
+module_platform_driver(bq257xx_reg_driver);
+
+MODULE_DESCRIPTION("bq257xx regulator driver");
+MODULE_AUTHOR("Chris Morgan <macromorgan@hotmail.com>");
+MODULE_LICENSE("GPL");
-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH V4 5/5] arm64: dts: rockchip: Add USB and charger to Gameforce Ace

[Chris Morgan]

From: Chris Morgan <macromorgan@hotmail.com>

Add support for the BQ25703A charger manager and boost regulator to
the Gameforce Ace. Add the USB-C port and PHY as well as they all
depend on each other for operation.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
 .../dts/rockchip/rk3588s-gameforce-ace.dts    | 122 ++++++++++++++++++
 1 file changed, 122 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts b/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts
index 873a2bd6a6de..e1ec1b3f4fc1 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts
@@ -575,6 +575,56 @@ &i2c6 {
 	pinctrl-0 = <&i2c6m3_xfer>;
 	status = "okay";
 
+	fusb302: typec@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PC7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&usbc0_int>;
+		pinctrl-names = "default";
+		vbus-supply = <&usb_otg_vbus>;
+
+		connector {
+			compatible = "usb-c-connector";
+			data-role = "dual";
+			label = "USB-C";
+			op-sink-microwatt = <1000000>;
+			power-role = "dual";
+			self-powered;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+				     PDO_FIXED(9000, 3000, PDO_FIXED_USB_COMM)
+				     PDO_FIXED(12000, 3000, PDO_FIXED_USB_COMM)>;
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			try-power-role = "sink";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usbc0_orien_sw: endpoint {
+						remote-endpoint = <&usbdp_phy0_orientation_switch>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					usbc0_role_sw: endpoint {
+						remote-endpoint = <&dwc3_0_role_switch>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					dp_altmode_mux: endpoint {
+						remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+					};
+				};
+			};
+		};
+	};
+
 	rtc_hym8563: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
@@ -603,8 +653,34 @@ battery@62 {
 			 0x2F 0x00 0x64 0xA5 0xB5 0x1C 0xF0 0x49>;
 		cellwise,monitor-interval-ms = <5000>;
 		monitored-battery = <&battery>;
+		power-supplies = <&bq25703>;
 		status = "okay";
 	};
+
+	bq25703: charger@6b {
+		compatible = "ti,bq25703a";
+		reg = <0x6b>;
+		input-current-limit-microamp = <5000000>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PD5 IRQ_TYPE_LEVEL_LOW>;
+		monitored-battery = <&battery>;
+		pinctrl-0 = <&charger_int_h>;
+		pinctrl-names = "default";
+		power-supplies = <&fusb302>;
+
+		regulators {
+			usb_otg_vbus: vbus {
+				enable-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
+				pinctrl-0 = <&boost_enable_h>;
+				pinctrl-names = "default";
+				regulator-max-microamp = <960000>;
+				regulator-max-microvolt = <5088000>;
+				regulator-min-microamp = <512000>;
+				regulator-min-microvolt = <4992000>;
+				regulator-name = "usb_otg_vbus";
+			};
+		};
+	};
 };
 
 &i2c7 {
@@ -807,6 +883,12 @@ usbc0_int: usbc0-int {
 			rockchip,pins =
 				<0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
+
+		usbc_sbu_dc: usbc-sbu-dc {
+			rockchip,pins =
+				<4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>,
+				<4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
 	};
 
 	vcc3v3-lcd {
@@ -1239,3 +1321,43 @@ bluetooth {
 		shutdown-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
 	};
 };
+
+&usb_host0_xhci {
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dwc3_0_role_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_role_sw>;
+		};
+	};
+};
+
+&usbdp_phy0 {
+	mode-switch;
+	orientation-switch;
+	pinctrl-0 = <&usbc_sbu_dc>;
+	pinctrl-names = "default";
+	sbu1-dc-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+	sbu2-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
+	rockchip,dp-lane-mux = <2 3>;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbdp_phy0_orientation_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_orien_sw>;
+		};
+
+		usbdp_phy0_dp_altmode_mux: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&dp_altmode_mux>;
+		};
+	};
+};
-- 
2.43.0


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH V4 1/5] dt-bindings: mfd: ti,bq25703a: Add TI BQ25703A Charger

[Krzysztof Kozlowski]

On Thu, Jun 26, 2025 at 02:53:39PM -0500, Chris Morgan wrote:
> From: Chris Morgan <macromorgan@hotmail.com>
> 
> Document the Texas instruments BQ25703A series of charger managers/
> buck/boost regulators.
> 
> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>

Didn't you receive tag?

> ---
>  .../devicetree/bindings/mfd/ti,bq25703a.yaml  | 117 ++++++++++++++++++
>  1 file changed, 117 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

<form letter>
This is a friendly reminder during the review process.

It looks like you received a tag and forgot to add it.

If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions of patchset, under or above your Signed-off-by tag, unless
patch changed significantly (e.g. new properties added to the DT
bindings). Tag is "received", when provided in a message replied to you
on the mailing list. Tools like b4 can help here. However, there's no
need to repost patches *only* to add the tags. The upstream maintainer
will do that for tags received on the version they apply.

Please read:
https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577

If a tag was not added on purpose, please state why and what changed.
</form letter>

Best regards,
Krzysztof


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH V4 1/5] dt-bindings: mfd: ti,bq25703a: Add TI BQ25703A Charger

[Christopher Morgan]

> On Jun 27, 2025, at 1:58 AM, Krzysztof Kozlowski <krzk@kernel.org> wrote:
> 
> On Thu, Jun 26, 2025 at 02:53:39PM -0500, Chris Morgan wrote:
>> From: Chris Morgan <macromorgan@hotmail.com>
>> 
>> Document the Texas instruments BQ25703A series of charger managers/
>> buck/boost regulators.
>> 
>> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> 
> Didn't you receive tag?

I did, I’m sorry but I thought the changes suggested were substantive enough to warrant another review so I dropped it. I did leave it on the other patches though. If I should have kept the tag I’ll try to remember next time.

> 
>> ---
>> .../devicetree/bindings/mfd/ti,bq25703a.yaml  | 117 ++++++++++++++++++
>> 1 file changed, 117 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mfd/ti,bq25703a.yaml
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> 
> <form letter>
> This is a friendly reminder during the review process.
> 
> It looks like you received a tag and forgot to add it.
> 
> If you do not know the process, here is a short explanation:
> Please add Acked-by/Reviewed-by/Tested-by tags when posting new
> versions of patchset, under or above your Signed-off-by tag, unless
> patch changed significantly (e.g. new properties added to the DT
> bindings). Tag is "received", when provided in a message replied to you
> on the mailing list. Tools like b4 can help here. However, there's no
> need to repost patches *only* to add the tags. The upstream maintainer
> will do that for tags received on the version they apply.
> 
> Please read:
> https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577
> 
> If a tag was not added on purpose, please state why and what changed.
> </form letter>
> 
> Best regards,
> Krzysztof
> 

Thank you,
Chris
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH V4 1/5] dt-bindings: mfd: ti,bq25703a: Add TI BQ25703A Charger

[Diederik de Haas]

[-- Attachment #1.1: Type: text/plain, Size: 845 bytes --]

On Mon Jun 30, 2025 at 4:33 PM CEST, Christopher Morgan wrote:
> On Jun 27, 2025, at 1:58 AM, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>> On Thu, Jun 26, 2025 at 02:53:39PM -0500, Chris Morgan wrote:
>>> From: Chris Morgan <macromorgan@hotmail.com>
>>> 
>>> Document the Texas instruments BQ25703A series of charger managers/
>>> buck/boost regulators.
>>> 
>>> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
>> 
>> Didn't you receive tag?
>
> I did, I’m sorry but I thought the changes suggested were substantive
> enough to warrant another review so I dropped it. I did leave it on
> the other patches though. If I should have kept the tag I’ll try to
> remember next time.

AFAIK that is a valid reason, but you should explicitly document that
you did and why, so everyone knows it's not an 'oversight'.


[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 170 bytes --]

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH V4 1/5] dt-bindings: mfd: ti,bq25703a: Add TI BQ25703A Charger

[Krzysztof Kozlowski]

On 30/06/2025 16:33, Christopher Morgan wrote:
> 
> 
>> On Jun 27, 2025, at 1:58 AM, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>>
>> On Thu, Jun 26, 2025 at 02:53:39PM -0500, Chris Morgan wrote:
>>> From: Chris Morgan <macromorgan@hotmail.com>
>>>
>>> Document the Texas instruments BQ25703A series of charger managers/
>>> buck/boost regulators.
>>>
>>> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
>>
>> Didn't you receive tag?
> 
> I did, I’m sorry but I thought the changes suggested were substantive enough to warrant another review so I dropped it. I did leave it on the other patches though. If I should have kept the tag I’ll try to remember next time.

Which changes? Cover letter is vague - only some sort of cleanup - and
anyway dropping tag needs to be explicit with a reason.

Best regards,
Krzysztof

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip