From: Shawn Lin <shawn.lin@rock-chips.com>
To: Manivannan Sadhasivam <mani@kernel.org>,
Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-rockchip@lists.infradead.org, linux-pci@vger.kernel.org,
Niklas Cassel <cassel@kernel.org>,
Shawn Lin <shawn.lin@rock-chips.com>
Subject: [PATCH v3 1/3] PCI: dw-rockchip: Move the INTx irq setup to probe
Date: Tue, 22 Sep 2026 10:37:00 +0800 [thread overview]
Message-ID: <1790044622-164744-2-git-send-email-shawn.lin@rock-chips.com> (raw)
In-Reply-To: <1790044622-164744-1-git-send-email-shawn.lin@rock-chips.com>
Since commit b376b3ff9cb0 ("PCI: dw-rockchip: Implement .reset_root_port()
and use for link down"), .reset_root_port() re-runs the host ops .init()
callback to reprogram the Root Complex after a controller reset. That
works for the register programming, but .init() is not re-entrant: it
also creates the INTx irq domain and installs the chained INTx handler.
Every root port reset therefore ends up with a second irq domain
registered for the same fwnode: the previous one is leaked, as it is
never removed, and worse, the INTx virqs of the downstream PCI devices
were allocated in the previous irq domain and are never re-mapped, while
the chained handler now looks up virqs in the new, empty domain. After a
link down recovery, INTx interrupts are silently lost.
Fix it by moving the of_irq_get_byname() lookup, the INTx irq domain
creation and the chained handler installation out of .init() and into
rockchip_pcie_configure_rc(), right after dw_pcie_host_init(). This
mirrors how the qcom driver requests its global IRQ, and leaves .init()
with nothing but idempotent register programming, so both
.reset_root_port() and dw_pcie_resume_noirq() can safely re-run it.
Re-running of_irq_get_byname() on every resume is also gone.
rockchip_pcie_configure_rc() can abort probe, so propagate the irq
domain creation error instead of only logging it as .init() used to do.
Fixes: b376b3ff9cb0 ("PCI: dw-rockchip: Implement .reset_root_port() and use for link down")
Suggested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
---
Changes in v3:
- split devm-managed part into a seperate patch
Changes in v2:
- Moved the of_irq_get_byname() lookup, the INTx irq domain creation
and the chained handler installation out of the host ops .init()
callback into rockchip_pcie_configure_rc(), right after
dw_pcie_host_init(), as suggested by Niklas Cassel. This supersedes
v1 patch 1/2, as .init() no longer creates the irq domain, and
removes the rockchip_pcie_host_hw_init() helper from v1.
- Made the INTx irq domain devm-managed with
devm_irq_domain_instantiate() and uninstall the chained handler
through a devres action, addressing the probe failure leak and
use-after-free flagged by the Sashiko review.
drivers/pci/controller/dwc/pcie-dw-rockchip.c | 32 +++++++++++++++------------
1 file changed, 18 insertions(+), 14 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-dw-rockchip.c b/drivers/pci/controller/dwc/pcie-dw-rockchip.c
index 1497686..8788a10 100644
--- a/drivers/pci/controller/dwc/pcie-dw-rockchip.c
+++ b/drivers/pci/controller/dwc/pcie-dw-rockchip.c
@@ -422,23 +422,9 @@ static void rockchip_pcie_stop_link(struct dw_pcie *pci)
static int rockchip_pcie_host_init(struct dw_pcie_rp *pp)
{
struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
- struct rockchip_pcie *rockchip = to_rockchip_pcie(pci);
- struct device *dev = rockchip->pci.dev;
- int irq, ret;
-
- irq = of_irq_get_byname(dev->of_node, "legacy");
- if (irq < 0)
- return irq;
pci->dbi_base2 = pci->dbi_base + PCIE_TYPE0_HDR_DBI2_OFFSET;
- ret = rockchip_pcie_init_irq_domain(rockchip);
- if (ret < 0)
- dev_err(dev, "failed to init irq domain\n");
-
- irq_set_chained_handler_and_data(irq, rockchip_pcie_intx_handler,
- rockchip);
-
rockchip_pcie_configure_l1ss(pci);
rockchip_pcie_enable_l0s(pci);
pp->bridge->reset_root_port = rockchip_pcie_rc_reset_root_port;
@@ -740,6 +726,24 @@ static int rockchip_pcie_configure_rc(struct platform_device *pdev,
return ret;
}
+ /*
+ * This is done here instead of in the host ops .init() callback,
+ * which is also re-run by .reset_root_port(), so that the INTx irq
+ * domain is only created once, at probe time.
+ */
+ irq = of_irq_get_byname(dev->of_node, "legacy");
+ if (irq < 0)
+ return irq;
+
+ ret = rockchip_pcie_init_irq_domain(rockchip);
+ if (ret < 0) {
+ dev_err(dev, "failed to init irq domain\n");
+ return ret;
+ }
+
+ irq_set_chained_handler_and_data(irq, rockchip_pcie_intx_handler,
+ rockchip);
+
/* unmask hot reset/link-down reset */
val = FIELD_PREP_WM16(PCIE_LINK_REQ_RST_NOT_INT, 0);
rockchip_pcie_writel_apb(rockchip, val, PCIE_CLIENT_INTR_MASK_MISC);
--
2.7.4
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2026-09-22 2:37 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-22 2:36 [PATCH v3 0/3] Small INTx fixes for Rockchip's dwc based PCIe controller driver Shawn Lin
2026-09-22 2:37 ` Shawn Lin [this message]
2026-09-22 9:56 ` [PATCH v3 1/3] PCI: dw-rockchip: Move the INTx irq setup to probe Niklas Cassel
2026-09-22 2:37 ` [PATCH v3 2/3] PCI: dw-rockchip: Make the INTx irq setup devm-managed Shawn Lin
2026-09-22 9:58 ` Niklas Cassel
2026-09-22 2:37 ` [PATCH v3 3/3] PCI: dw-rockchip: Mask the INTx IRQ while the controller clocks are gated Shawn Lin
2026-09-23 9:13 ` [PATCH v3 0/3] Small INTx fixes for Rockchip's dwc based PCIe controller driver Diederik de Haas
2026-09-23 9:21 ` Shawn Lin
2026-09-23 15:25 ` Niklas Cassel
2026-09-24 3:27 ` Shawn Lin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1790044622-164744-2-git-send-email-shawn.lin@rock-chips.com \
--to=shawn.lin@rock-chips.com \
--cc=bhelgaas@google.com \
--cc=cassel@kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=mani@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox