From: Heiko Stuebner <heiko@sntech.de>
To: heiko@sntech.de
Cc: ukleinek@debian.org, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 12/14] arm64: dts: rockchip: add missing pmic information on Qnap-TS433
Date: Sun, 21 Jul 2024 19:37:21 +0200 [thread overview]
Message-ID: <20240721173723.919961-13-heiko@sntech.de> (raw)
In-Reply-To: <20240721173723.919961-1-heiko@sntech.de>
Fill in the missing pieces for RK809 pmic used on the TS433.
The regulator setup comes from the vendor-devicetree, so without proper
schematics its accuracy is somewhat unclear, but it looks really similar
to all the other rk3568 boards, so follows the reference design it seems.
The one caveat is related to vcc3v3_sd. This regulator needs to stay on.
When turned off because of no users, access to both PCIe controllers
will stall. Maybe this rail does supply the 100MHz refclk generation
or so.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
.../boot/dts/rockchip/rk3568-qnap-ts433.dts | 229 +++++++++++++++++-
1 file changed, 227 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index a576d45ccc3e0..779e1b8a35ca5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -101,6 +101,16 @@ vcc3v3_pcie: regulator-vcc3v3-pcie {
vin-supply = <&dc_12v>;
};
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
vcc5v0_host: regulator-vcc5v0-host {
compatible = "regulator-fixed";
enable-active-high;
@@ -202,11 +212,220 @@ &gmac0_rgmii_clk
&i2c0 {
status = "okay";
- pmic@20 {
+ rk809: pmic@20 {
compatible = "rockchip,rk809";
reg = <0x20>;
interrupt-parent = <&gpio0>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ system-power-controller;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ /*
+ * turning this off, breaks access to both
+ * PCIe controllers, refclk generator perhaps
+ */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
};
vdd_cpu: regulator@40 {
@@ -287,6 +506,12 @@ hdd4_led_pin: hdd4_led-pin {
};
};
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
usb {
vcc5v0_host_en: vcc5v0-host-en {
rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
--
2.39.2
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2024-07-21 17:42 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-07-21 17:37 [PATCH v2 00/14] Expand available features on Qnap TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 01/14] arm64: dts: rockchip: add PCIe supply regulator to Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 02/14] arm64: dts: rockchip: enable second PCIe controller on the Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 03/14] arm64: dts: rockchip: enable uart0 on Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 04/14] arm64: dts: rockchip: enable usb ports " Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 05/14] arm64: dts: rockchip: add stdout path " Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 06/14] arm64: dts: rockchip: enable sata1+2 " Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 07/14] arm64: dts: rockchip: add board-aliases for Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 08/14] arm64: dts: rockchip: add hdd leds to Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 09/14] arm64: dts: rockchip: enable the tsadc on the Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 10/14] arm64: dts: rockchip: add gpio-keys to Qnap-TS433 Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 11/14] arm64: dts: rockchip: define cpu-supply on the Qnap-TS433 Heiko Stuebner
2024-07-21 17:44 ` Heiko Stübner
2024-07-21 17:37 ` Heiko Stuebner [this message]
2024-07-21 17:45 ` [PATCH v2 12/14] arm64: dts: rockchip: add missing pmic information on Qnap-TS433 Heiko Stübner
2024-07-21 17:37 ` [PATCH v2 13/14] arm64: dts: rockchip: enable gpu " Heiko Stuebner
2024-07-21 17:37 ` [PATCH v2 14/14] arm64: dts: rockchip: add 2 pmu_io_domain supplies for Qnap-TS433 Heiko Stuebner
2024-07-22 15:20 ` [PATCH v2 00/14] Expand available features on Qnap TS433 Uwe Kleine-König
2024-07-23 2:57 ` Rob Herring (Arm)
2024-07-23 10:03 ` Heiko Stübner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240721173723.919961-13-heiko@sntech.de \
--to=heiko@sntech.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=ukleinek@debian.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox