From: Chris Morgan <macroalpha82@gmail.com>
To: linux-rockchip@lists.infradead.org
Cc: linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
broonie@kernel.org, lee@kernel.org, lgirdwood@gmail.com,
sre@kernel.org, heiko@sntech.de, conor+dt@kernel.org,
krzk+dt@kernel.org, robh@kernel.org,
Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V7 5/5] arm64: dts: rockchip: Add USB and charger to Gameforce Ace
Date: Thu, 21 Aug 2025 11:24:48 -0500 [thread overview]
Message-ID: <20250821162448.117621-6-macroalpha82@gmail.com> (raw)
In-Reply-To: <20250821162448.117621-1-macroalpha82@gmail.com>
From: Chris Morgan <macromorgan@hotmail.com>
Add support for the BQ25703A charger manager and boost regulator to
the Gameforce Ace. Add the USB-C port and PHY as well as they all
depend on each other for operation.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
.../dts/rockchip/rk3588s-gameforce-ace.dts | 122 ++++++++++++++++++
1 file changed, 122 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts b/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts
index 55fc7cbef58d..f5894672fcbd 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-gameforce-ace.dts
@@ -612,6 +612,56 @@ &i2c6 {
pinctrl-0 = <&i2c6m3_xfer>;
status = "okay";
+ fusb302: typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PC7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&usbc0_int>;
+ pinctrl-names = "default";
+ vbus-supply = <&usb_otg_vbus>;
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "dual";
+ label = "USB-C";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ self-powered;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_FIXED(9000, 3000, PDO_FIXED_USB_COMM)
+ PDO_FIXED(12000, 3000, PDO_FIXED_USB_COMM)>;
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "sink";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_orien_sw: endpoint {
+ remote-endpoint = <&usbdp_phy0_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_role_sw: endpoint {
+ remote-endpoint = <&dwc3_0_role_switch>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+
rtc_hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
@@ -640,8 +690,34 @@ battery@62 {
0x2F 0x00 0x64 0xA5 0xB5 0x1C 0xF0 0x49>;
cellwise,monitor-interval-ms = <5000>;
monitored-battery = <&battery>;
+ power-supplies = <&bq25703>;
status = "okay";
};
+
+ bq25703: charger@6b {
+ compatible = "ti,bq25703a";
+ reg = <0x6b>;
+ input-current-limit-microamp = <5000000>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD5 IRQ_TYPE_LEVEL_LOW>;
+ monitored-battery = <&battery>;
+ pinctrl-0 = <&charger_int_h>;
+ pinctrl-names = "default";
+ power-supplies = <&fusb302>;
+
+ regulators {
+ usb_otg_vbus: vbus {
+ enable-gpios = <&gpio4 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&boost_enable_h>;
+ pinctrl-names = "default";
+ regulator-max-microamp = <960000>;
+ regulator-max-microvolt = <5088000>;
+ regulator-min-microamp = <512000>;
+ regulator-min-microvolt = <4992000>;
+ regulator-name = "usb_otg_vbus";
+ };
+ };
+ };
};
&i2c7 {
@@ -853,6 +929,12 @@ usbc0_int: usbc0-int {
rockchip,pins =
<0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>;
};
+
+ usbc_sbu_dc: usbc-sbu-dc {
+ rockchip,pins =
+ <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>,
+ <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
};
vcc3v3-lcd {
@@ -1286,6 +1368,46 @@ bluetooth {
};
};
+&usb_host0_xhci {
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dwc3_0_role_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_role_sw>;
+ };
+ };
+};
+
+&usbdp_phy0 {
+ mode-switch;
+ orientation-switch;
+ pinctrl-0 = <&usbc_sbu_dc>;
+ pinctrl-names = "default";
+ sbu1-dc-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
+ rockchip,dp-lane-mux = <2 3>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orien_sw>;
+ };
+
+ usbdp_phy0_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dp_altmode_mux>;
+ };
+ };
+};
+
&vop {
status = "okay";
};
--
2.43.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
prev parent reply other threads:[~2025-08-21 22:39 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-21 16:24 [PATCH V7 0/5] Add Texas Instruments BQ25703A Charger Chris Morgan
2025-08-21 16:24 ` [PATCH V7 1/5] dt-bindings: mfd: ti,bq25703a: Add TI " Chris Morgan
2025-08-21 16:24 ` [PATCH V7 2/5] mfd: bq257xx: Add support for BQ25703A core driver Chris Morgan
2025-09-02 14:13 ` Lee Jones
2025-08-21 16:24 ` [PATCH V7 3/5] power: supply: bq257xx: Add support for BQ257XX charger Chris Morgan
2025-08-21 16:24 ` [PATCH V7 4/5] regulator: bq257xx: Add bq257xx boost regulator driver Chris Morgan
2025-08-21 16:24 ` Chris Morgan [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250821162448.117621-6-macroalpha82@gmail.com \
--to=macroalpha82@gmail.com \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=heiko@sntech.de \
--cc=krzk+dt@kernel.org \
--cc=lee@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-pm@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=macromorgan@hotmail.com \
--cc=robh@kernel.org \
--cc=sre@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).