From: Vladislav Leonov <vlad@zlab.su>
To: Jonathan Cameron <jic23@kernel.org>
Cc: "David Lechner" <dlechner@baylibre.com>,
"Nuno Sá" <nuno.sa@analog.com>,
"Andy Shevchenko" <andy@kernel.org>,
"Heiko Stuebner" <heiko@sntech.de>,
"Simon Glass" <sjg@chromium.org>,
linux-iio@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
"Vladislav Leonov" <vlad@zlab.su>
Subject: [PATCH] iio: adc: rockchip_saradc: Add support for RV1106
Date: Mon, 10 Aug 2026 12:08:26 +0300 [thread overview]
Message-ID: <20260810090826.146758-1-vlad@zlab.su> (raw)
In-Reply-To: <20260714131631.v2.1.0b846080833e4b836793c43fc26d1c6d817cf9b4@changeid>
The Successive Approximation ADC (SARADC) in RV1106 uses the v2
controller and supports:
- 10-bit resolution
- Up to 1MS/s sampling rate
- 2 single-ended input channels
"dt-bindings: iio: adc: rockchip-saradc: Add RV1106 compatible"
documents "rockchip,rv1106-saradc" as falling back to
"rockchip,rk3588-saradc" (see Link below). The two IP blocks are not
equivalent, though: per the RV1106 TRM v0.3, chapter 20 (SAR-ADC),
RV1106 only has 2 channels at 10-bit resolution, versus 8 channels
at 12-bit on RK3588. Without a dedicated match entry, the driver
binds via the fallback compatible and uses the RK3588 channel table,
which reports 8 channels instead of 2, and an in_voltage_scale that
is off by exactly 4x (4096 vs 1024 full-scale).
Add a dedicated compatible/data pair for RV1106 with the correct
2-channel, 10-bit layout.
Tested on a custom RV1106-based board, with:
&saradc {
vref-supply = <&vcc_saradc>; /* 1.8V fixed regulator */
status = "okay";
};
Before this patch:
# ls /sys/bus/iio/devices/iio:device0/in_voltage*_raw | wc -l
8
# cat /sys/bus/iio/devices/iio:device0/in_voltage_scale
0.439453125
After this patch:
# ls /sys/bus/iio/devices/iio:device0/in_voltage*_raw | wc -l
2
# cat /sys/bus/iio/devices/iio:device0/in_voltage_scale
1.757812500
Link: https://lore.kernel.org/all/20260714131631.v2.1.0b846080833e4b836793c43fc26d1c6d817cf9b4@changeid/
Signed-off-by: Vladislav Leonov <vlad@zlab.su>
---
drivers/iio/adc/rockchip_saradc.c | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/drivers/iio/adc/rockchip_saradc.c b/drivers/iio/adc/rockchip_saradc.c
index 0f0bf2906af0..5c45fae11890 100644
--- a/drivers/iio/adc/rockchip_saradc.c
+++ b/drivers/iio/adc/rockchip_saradc.c
@@ -348,6 +348,19 @@ static const struct rockchip_saradc_data rk3588_saradc_data = {
.read = rockchip_saradc_read_v2,
};
+static const struct iio_chan_spec rockchip_rv1106_saradc_iio_channels[] = {
+ SARADC_CHANNEL(0, "adc0", 10),
+ SARADC_CHANNEL(1, "adc1", 10),
+};
+
+static const struct rockchip_saradc_data rv1106_saradc_data = {
+ .channels = rockchip_rv1106_saradc_iio_channels,
+ .num_channels = ARRAY_SIZE(rockchip_rv1106_saradc_iio_channels),
+ .clk_rate = 1000000,
+ .start = rockchip_saradc_start_v2,
+ .read = rockchip_saradc_read_v2,
+};
+
static const struct of_device_id rockchip_saradc_match[] = {
{
.compatible = "rockchip,saradc",
@@ -370,6 +383,9 @@ static const struct of_device_id rockchip_saradc_match[] = {
}, {
.compatible = "rockchip,rk3588-saradc",
.data = &rk3588_saradc_data,
+ }, {
+ .compatible = "rockchip,rv1106-saradc",
+ .data = &rv1106_saradc_data,
},
{ }
};
--
2.47.3
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
prev parent reply other threads:[~2026-08-10 9:11 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-14 19:16 [PATCH v2] dt-bindings: iio: adc: rockchip-saradc: Add RV1106 compatible Simon Glass
2026-07-15 4:52 ` Krzysztof Kozlowski
2026-07-15 19:21 ` Heiko Stuebner
2026-07-20 1:39 ` Jonathan Cameron
2026-08-10 9:08 ` Vladislav Leonov [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260810090826.146758-1-vlad@zlab.su \
--to=vlad@zlab.su \
--cc=andy@kernel.org \
--cc=dlechner@baylibre.com \
--cc=heiko@sntech.de \
--cc=jic23@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=nuno.sa@analog.com \
--cc=sjg@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox