Re: [PATCH 13/14] drm/bridge: synopsys: Add DW HDMI QP TX controller driver

[Cristian Ciocaltea <cristian.ciocaltea@collabora.com>]

On 6/5/24 5:48 PM, Heiko Stübner wrote:
> Am Samstag, 1. Juni 2024, 15:12:35 CEST schrieb Cristian Ciocaltea:
>> The Synopsys DesignWare HDMI 2.1 Quad-Pixel (QP) TX controller supports
>> the following features, among others:
>>
>> * Fixed Rate Link (FRL)
>> * 4K@120Hz and 8K@60Hz video modes
>> * Variable Refresh Rate (VRR) including Quick Media Switching (QMS), aka
>>   Cinema VRR
>> * Fast Vactive (FVA), aka Quick Frame Transport (QFT)
>> * SCDC I2C DDC access
>> * TMDS Scrambler enabling 2160p@60Hz with RGB/YCbCr4:4:4
>> * YCbCr4:2:0 enabling 2160p@60Hz at lower HDMI link speeds
>> * Multi-stream audio
>> * Enhanced Audio Return Channel (EARC)
>>
>> Add driver to enable basic support, i.e. RGB output up to 4K@60Hz,
>> without audio, CEC or any HDMI 2.1 specific features.
>>
>> Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
>> Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
>> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
>> ---
>>  drivers/gpu/drm/bridge/synopsys/Makefile     |   2 +-
>>  drivers/gpu/drm/bridge/synopsys/dw-hdmi-qp.c | 787 +++++++++++++++++++++++++
>>  drivers/gpu/drm/bridge/synopsys/dw-hdmi-qp.h | 831 +++++++++++++++++++++++++++
>>  include/drm/bridge/dw_hdmi.h                 |   8 +
>>  4 files changed, 1627 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
>> index ce715562e9e5..8354e4879f70 100644
>> --- a/drivers/gpu/drm/bridge/synopsys/Makefile
>> +++ b/drivers/gpu/drm/bridge/synopsys/Makefile
> 
>> +static int dw_hdmi_qp_i2c_read(struct dw_hdmi *hdmi,
>> +			       unsigned char *buf, unsigned int length)
>> +{
>> +	struct dw_hdmi_i2c *i2c = hdmi->i2c;
>> +	int stat;
>> +
>> +	if (!i2c->is_regaddr) {
>> +		dev_dbg(hdmi->dev, "set read register address to 0\n");
>> +		i2c->slave_reg = 0x00;
>> +		i2c->is_regaddr = true;
>> +	}
>> +
>> +	while (length--) {
>> +		reinit_completion(&i2c->cmp);
>> +
>> +		dw_hdmi_qp_mod(hdmi, i2c->slave_reg++ << 12, I2CM_ADDR,
>> +			       I2CM_INTERFACE_CONTROL0);
>> +
>> +		dw_hdmi_qp_mod(hdmi, I2CM_FM_READ, I2CM_WR_MASK,
>> +			       I2CM_INTERFACE_CONTROL0);
> 
> Somehow the segment handling is present in the rest of the i2c code here, but
> not the actual handling for reads.
> 
> The vendor-kernel does:
> 
> -               dw_hdmi_qp_mod(hdmi, I2CM_FM_READ, I2CM_WR_MASK,
> -                              I2CM_INTERFACE_CONTROL0);
> +               if (i2c->is_segment)
> +                       dw_hdmi_qp_mod(hdmi, I2CM_EXT_READ, I2CM_WR_MASK,
> +                                      I2CM_INTERFACE_CONTROL0);
> +               else
> +                       dw_hdmi_qp_mod(hdmi, I2CM_FM_READ, I2CM_WR_MASK,
> +                                      I2CM_INTERFACE_CONTROL0);

Hmm, for some reason this is not present in the stable-5.10-rock5 branch 
I've been using as an implementation reference:

https://github.com/radxa/kernel/blob/stable-5.10-rock5/drivers/gpu/drm/bridge/synopsys/dw-hdmi-qp.c#L760

Is there an updated fork?

> Without this change, connecting to a DVI display does not work, and
> reading the EDID ends in the "i2c read error" below.
> 
> Adding the segment handling as above makes the DVI connection
> work (as it does in the vendor-kernel).
> 
> So it would be nice if you could maybe incorporate this in the next version?

Sure, thanks for pointing this out!

Cristian

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip