Re: [PATCH v5 3/3] usb: dwc2: Properly account for the force mode delays

["Heiko Stübner" <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>]

Am Dienstag, 13. September 2016, 20:07:25 schrieb Stefan Wahren:
> Hi Heiko,
> 
> > Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org> hat am 12. September 2016 um 13:05
> > geschrieben:
> > 
> > 
> > Hi Stefan,
> > 
> > Am Montag, 12. September 2016, 07:20:44 CEST schrieb Stefan Wahren:
> > > > Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org> hat am 11. September 2016 um 23:19
> > > > geschrieben:
> > > > 
> > > > Am Mittwoch, 7. September 2016, 19:39:43 CEST schrieb John Youn:
> > > > > When a force mode bit is set and the IDDIG debounce filter is
> > > > > enabled,
> > > > > there is a delay for the forced mode to take effect. This delay is
> > > > > due
> > > > > to the IDDIG debounce filter and is variable depending on the
> > > > > platform's
> > > > > PHY clock speed. To account for this delay we can poll for the
> > > > > expected
> > > > > mode.
> > > > > 
> > > > > On a clear force mode, since we don't know what mode to poll for,
> > > > > delay
> > > > > for a fixed 100 ms. This is the maximum delay based on the slowest
> > > > > PHY
> > > > > clock speed.
> > > > > 
> > > > > Tested-by: Stefan Wahren <stefan.wahren-eS4NqCHxEME@public.gmane.org>
> > > > > Signed-off-by: John Youn <johnyoun-HKixBCOQz3hWk0Htik3J/w@public.gmane.org>
> > > > > ---
> > > > 
> > > > [...]
> > > > 
> > > > > @@ -475,12 +478,6 @@ void dwc2_force_dr_mode(struct dwc2_hsotg
> > > > > *hsotg)
> > > > > 
> > > > >  			 __func__, hsotg->dr_mode);
> > > > >  		
> > > > >  		break;
> > > > >  	
> > > > >  	}
> > > > > 
> > > > > -
> > > > > -	/*
> > > > > -	 * NOTE: This is required for some rockchip soc based
> > > > > -	 * platforms.
> > > > > -	 */
> > > > > -	msleep(50);
> > > > > 
> > > > >  }
> > > > 
> > > > sorry for not finding the time to test your subsequent versions, but
> > > > this
> > > > still
> > > > acts up on my Rockchip boards, as I'm still running into errors like
> > > > 
> > > > 	[    4.875570] usb usb2-port1: connect-debounce failed
> > > 
> > > could you please name the relevant DTS file of the affected boards?
> > 
> > So far I've been able to see that on
> > 
> > rk3188-radxarock
> > rk3036-kylin
> > 
> > both on host-only dwc2 controllers.
> 
> thanks, does patch 1 & 2 already have a negative effect on these
> controllers?

nope, patches 1+2 alone are ok and only the msleep(50) going away causes 
problems. I'm back home now, so I'll hopefully have time to check host-only 
vs. otg dwc2 controllers tomorrow as well.


Heiko