* Re: Help regarding Cyclictest.
[not found] ` <CAOZUVQwOgcNkJz46E0rDy_8W-Po=cSkTLg2gf7sQc9XRNftUyw@mail.gmail.com>
@ 2015-01-06 21:26 ` Clark Williams
2015-01-08 16:42 ` Steven Rostedt
0 siblings, 1 reply; 3+ messages in thread
From: Clark Williams @ 2015-01-06 21:26 UTC (permalink / raw)
To: Ipsit Kumar, RT
[-- Attachment #1: Type: text/plain, Size: 5439 bytes --]
On Fri, 2 Jan 2015 15:02:11 +0530
Ipsit Kumar <kumaripsit1@gmail.com> wrote:
> Hi sir,
> Good Afternoon.
> Thank you for your reply.
>
> I am facing some issues with cyclictest.
> Basically i am using this tool on ARM platform, specifically on TCI6614 evm.
> I am seeing strange spike in the cyclictest result.
>
>
>
>
>
> *root # ./cyclictest -t1 -p80 -i 10000 -l 10000# /dev/cpu_dma_latency set
> to 0uspolicy: fifo: loadavg: 0.70 0.48 0.61 1/434 15283 T: 0
> (15226) P:80 I:10000 C: 10000 Min: 5 Act: 9 Avg: 17 Max: 5797*
>
> When I am plotting the Histogram, I see the latency to go beyond 3ms once.
> I am unable to figure out what is the reason behind this.
> Checked with the kernel configuration and found that the CPU Frequency
> scaling is Disabled.
> No power management features are enabled.
>
> It would be a great help, if you could point out something I am doing
> wrong.
>
> Thank you.
Sorry for the slow response time, but I've been swamped with things
here at work following the Christmas break.
First, I don't see anything offhand that you're doing wrong. What
version of the realtime kernel are you running?
I think your best bet may be to take this to the Linux Realtime users
mailing list (in CC).
To get a sense of where things are going wrong, you can run cyclictest
with the -b option, like this:
$ cyclictest -t1 -p80 -i 10000 -l 10000 -b 500
This will enable the ftrace system and will cause the event tracepoints
to be enabled. When a latency is measured greater than the specified
argument (in this case 500 microseconds), cyclictest will first stop
ftrace and will then exit. You can at that point use the trace-cmd
command to save off the trace buffers:
$ trace-cmd extract
This will generate the file trace.bin which is a binary
representation of the kernel trace buffers. You can then generate a
latency trace report using:
$ trace-cmd report -l
This will give you an idea of what code paths were taken prior to the
latency spike. From here it's a matter of figuring out what happened
and how to prevent it from happening.
>
> On Mon, Dec 29, 2014 at 4:06 AM, Clark Williams <williams@redhat.com> wrote:
>
> > You won't be able to use cyclictest to determine those. Cyclictest
> > measures scheduler latency (the amount of time from an event occurrence
> > to when a thread is scheduled because of that event). Scheduler latency
> > has interrupt latency and context switch time as components.
> >
> > Also, realize that interrupt latency and context switch time are going
> > to be close to constants, as well as very small components of the
> > overall scheduler latency. If you're going to measure those, you should
> > look at ftrace tracepoints or the 'perf' utility.
> >
> > On Wed, 24 Dec 2014 13:17:03 +0530
> > Ipsit Kumar <kumaripsit1@gmail.com> wrote:
> >
> > > Hello sir,
> > > Its really great to use this tool.
> > > I was trying to know the interrupt Latency and the context switch
> > latency.
> > > Would you like to give me pointer to trace those using cyclic test and
> > > the way to measure the performance using the the ARM performance counter
> > ?
> > >
> > > Thanks a lot for your help sir.
> > >
> > > On Wed, Dec 24, 2014 at 9:14 AM, Ipsit Kumar <kumaripsit1@gmail.com>
> > wrote:
> > >
> > > > Thanks a lot for your reply.
> > > >
> > > >
> > > >
> > > > On Tue, Dec 23, 2014 at 11:56 PM, Clark Williams <williams@redhat.com>
> > > > wrote:
> > > >
> > > >> On Tue, 23 Dec 2014 15:52:18 +0530
> > > >> Ipsit Kumar <kumaripsit1@gmail.com> wrote:
> > > >>
> > > >> > hello sir,
> > > >> > I am using the cyclictest tool to do some latency test on my linux
> > rt
> > > >> > kernel.
> > > >> > I am unable to understand the statistics that are being printed.
> > > >> > I want to know what is min max and avg that are being printed ?
> > > >> > Would be a great help to hear from you sir.
> > > >> >
> > > >> > Thank you.
> > > >> >
> > > >> > --
> > > >> > Regards:
> > > >> > Ipsit Kumar Senapati
> > > >> > *.*
> > > >>
> > > >> Cyclictest measures what I call "scheduler latency". It measures the
> > > >> time between when the program should wakeup and when it actually does.
> > > >> Some pseudo code:
> > > >>
> > > >> t1 = clock_gettime()
> > > >> while running
> > > >> clock_nanosleep(interval)
> > > >> t2 = clock_gettime()
> > > >> delta = t2 - (t1 + interval)
> > > >> t1 = t2
> > > >>
> > > >> So in a perfect world we would wakeup at time t1+interval, but of
> > > >> course we're not perfect and there's system overhead to take into
> > > >> account. The delta value is the scheduler latency.
> > > >>
> > > >> The min value printed out is the lowest scheduler latency recorded,
> > > >> while the max value is the largest scheduler latency recorded for a
> > > >> particular core, both reported in microseconds. The avg value is a
> > > >> running average of the delta values for a particular core.
> > > >>
> > > >> Clark
> > > >>
> > > >
> > > >
> > > >
> > > > --
> > > > Regards:
> > > > Ipsit Kumar Senapati
> > > > *.*
> > > >
> > >
> > >
> > >
> > > --
> > > Regards:
> > > Ipsit Kumar Senapati
> > > *.*
> >
>
>
>
> --
> Regards:
> Ipsit Kumar Senapati
> *.*
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread