From: Pierre Gondois <pierre.gondois@arm.com>
To: Sebastian Andrzej Siewior <bigeasy@linutronix.de>,
Thomas Gleixner <tglx@linutronix.de>
Cc: LKML <linux-kernel@vger.kernel.org>,
linux-rt-users@vger.kernel.org,
Steven Rostedt <rostedt@goodmis.org>,
Valentin Schneider <vschneid@redhat.com>,
Dietmar Eggemann <dietmar.eggemann@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
Pierre Gondois <pierre.gondois@arm.com>
Subject: Re: [ANNOUNCE] v6.0.5-rt14
Date: Fri, 28 Oct 2022 11:47:28 +0200 [thread overview]
Message-ID: <649af0f6-e5e2-c450-879c-e9153e0c0abc@arm.com> (raw)
In-Reply-To: <Y1o8hqwQKDpOTkNr@linutronix.de>
Hello Sebastian,
About the issues Valentin reported:
- [SPLAT 1/3] arm_pmu: Sleeping spinlocks down armpmu_alloc_atomic()
will be fixed by:
https://lore.kernel.org/all/20220930111844.1522365-1-mark.rutland@arm.com/
- [SPLAT 2/3] irqchip/gic-v3-its: Sleeping spinlocks down gic_reserve_range()
was fixed by:
https://lore.kernel.org/lkml/20211027151506.2085066-3-valentin.schneider@arm.com/
- [SPLAT 3/3] gpio: dwapb: Sleeping spinlocks down IRQ mapping
was fixed by:
https://lore.kernel.org/all/20220419012810.88417-1-schspa@gmail.com/
Regards,
Pierre
On 10/27/22 10:08, Sebastian Andrzej Siewior wrote:
> Dear RT folks!
>
> I'm pleased to announce the v6.0.5-rt14 patch set.
>
> Changes since v6.0.5-rt13:
>
> - Replace deprecated API in the Xilinx AXI Ethernet driver so that it
> compiles again. Reported by David Runge.
>
> Known issues
> - Valentin Schneider reported a few splats on ARM64, see
> https://lkml.kernel.org/r/20210810134127.1394269-1-valentin.schneider@arm.com
>
> The delta patch against v6.0.5-rt13 is appended below and can be found here:
>
> https://cdn.kernel.org/pub/linux/kernel/projects/rt/6.0/incr/patch-6.0.5-rt13-rt14.patch.xz
>
> You can get this release via the git tree at:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/rt/linux-rt-devel.git v6.0.5-rt14
>
> The RT patch against v6.0.5 can be found here:
>
> https://cdn.kernel.org/pub/linux/kernel/projects/rt/6.0/older/patch-6.0.5-rt14.patch.xz
>
> The split quilt queue is available at:
>
> https://cdn.kernel.org/pub/linux/kernel/projects/rt/6.0/older/patches-6.0.5-rt14.tar.xz
>
> Sebastian
>
> diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
> index 9262988d26a32..2c233b59e7d93 100644
> --- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
> +++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
> @@ -1305,16 +1305,16 @@ axienet_get_stats64(struct net_device *dev, struct rtnl_link_stats64 *stats)
> netdev_stats_to_stats64(stats, &dev->stats);
>
> do {
> - start = u64_stats_fetch_begin_irq(&lp->rx_stat_sync);
> + start = u64_stats_fetch_begin(&lp->rx_stat_sync);
> stats->rx_packets = u64_stats_read(&lp->rx_packets);
> stats->rx_bytes = u64_stats_read(&lp->rx_bytes);
> - } while (u64_stats_fetch_retry_irq(&lp->rx_stat_sync, start));
> + } while (u64_stats_fetch_retry(&lp->rx_stat_sync, start));
>
> do {
> - start = u64_stats_fetch_begin_irq(&lp->tx_stat_sync);
> + start = u64_stats_fetch_begin(&lp->tx_stat_sync);
> stats->tx_packets = u64_stats_read(&lp->tx_packets);
> stats->tx_bytes = u64_stats_read(&lp->tx_bytes);
> - } while (u64_stats_fetch_retry_irq(&lp->tx_stat_sync, start));
> + } while (u64_stats_fetch_retry(&lp->tx_stat_sync, start));
> }
>
> static const struct net_device_ops axienet_netdev_ops = {
> diff --git a/localversion-rt b/localversion-rt
> index 9f7d0bdbffb18..08b3e75841adc 100644
> --- a/localversion-rt
> +++ b/localversion-rt
> @@ -1 +1 @@
> --rt13
> +-rt14
next prev parent reply other threads:[~2022-10-28 9:47 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-27 8:08 [ANNOUNCE] v6.0.5-rt14 Sebastian Andrzej Siewior
2022-10-28 9:47 ` Pierre Gondois [this message]
2022-10-31 13:26 ` Sebastian Andrzej Siewior
2022-10-31 14:06 ` Clark Williams
2022-12-13 13:56 ` Pierre Gondois
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=649af0f6-e5e2-c450-879c-e9153e0c0abc@arm.com \
--to=pierre.gondois@arm.com \
--cc=bigeasy@linutronix.de \
--cc=dietmar.eggemann@arm.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rt-users@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=rostedt@goodmis.org \
--cc=tglx@linutronix.de \
--cc=vschneid@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox