From: Alex Elder <elder@riscstar.com>
To: lee@kernel.org, lgirdwood@gmail.com, broonie@kernel.org,
alexandre.belloni@bootlin.com, robh@kernel.org,
krzk+dt@kernel.org, conor+dt@kernel.org
Cc: mat.jonczyk@o2.pl, dlan@gentoo.org, paul.walmsley@sifive.com,
palmer@dabbelt.com, aou@eecs.berkeley.edu, alex@ghiti.fr,
troymitchell988@gmail.com, guodong@riscstar.com,
linux-rtc@vger.kernel.org, devicetree@vger.kernel.org,
linux-riscv@lists.infradead.org, spacemit@lists.linux.dev,
linux-kernel@vger.kernel.org
Subject: [PATCH v7 2/8] mfd: simple-mfd-i2c: specify max_register
Date: Wed, 2 Jul 2025 16:36:51 -0500 [thread overview]
Message-ID: <20250702213658.545163-3-elder@riscstar.com> (raw)
In-Reply-To: <20250702213658.545163-1-elder@riscstar.com>
All devices supported by simple MFD use the same 8-bit register
8-bit value regmap configuration. There is an option available
for a device to specify a custom configuration, but no existing
device uses it.
Rather than specify a "full" regmap configuration to use this
option, Lee Jones suggested allowing just the max_register value
to be specified in the simple_mfd_data structure.
Signed-off-by: Alex Elder <elder@riscstar.com>
Suggested-by: Lee Jones <lee@kernel.org>
---
v2: - Allow max_register *and* regmap_config to be supplied
drivers/mfd/simple-mfd-i2c.c | 15 ++++++++++++---
drivers/mfd/simple-mfd-i2c.h | 1 +
2 files changed, 13 insertions(+), 3 deletions(-)
diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
index 22159913bea03..3f959f4f98261 100644
--- a/drivers/mfd/simple-mfd-i2c.c
+++ b/drivers/mfd/simple-mfd-i2c.c
@@ -33,16 +33,25 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c)
{
const struct simple_mfd_data *simple_mfd_data;
const struct regmap_config *regmap_config;
+ struct regmap_config config;
struct regmap *regmap;
int ret;
simple_mfd_data = device_get_match_data(&i2c->dev);
/* If no regmap_config is specified, use the default 8reg and 8val bits */
- if (!simple_mfd_data || !simple_mfd_data->regmap_config)
+ if (simple_mfd_data) {
+ if (simple_mfd_data->regmap_config)
+ config = *simple_mfd_data->regmap_config;
+ else
+ config = regmap_config_8r_8v;
+
+ if (simple_mfd_data->max_register)
+ config.max_register = simple_mfd_data->max_register;
+ regmap_config = &config;
+ } else {
regmap_config = ®map_config_8r_8v;
- else
- regmap_config = simple_mfd_data->regmap_config;
+ }
regmap = devm_regmap_init_i2c(i2c, regmap_config);
if (IS_ERR(regmap))
diff --git a/drivers/mfd/simple-mfd-i2c.h b/drivers/mfd/simple-mfd-i2c.h
index 7cb2bdd347d97..706b6f53155ff 100644
--- a/drivers/mfd/simple-mfd-i2c.h
+++ b/drivers/mfd/simple-mfd-i2c.h
@@ -27,6 +27,7 @@ struct simple_mfd_data {
const struct regmap_config *regmap_config;
const struct mfd_cell *mfd_cell;
size_t mfd_cell_size;
+ unsigned int max_register;
};
#endif /* __MFD_SIMPLE_MFD_I2C_H */
--
2.45.2
next prev parent reply other threads:[~2025-07-02 21:37 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-07-02 21:36 [PATCH v7 0/8] spacemit: introduce P1 PMIC support Alex Elder
2025-07-02 21:36 ` [PATCH v7 1/8] dt-bindings: mfd: add support the SpacemiT P1 PMIC Alex Elder
2025-07-02 21:36 ` Alex Elder [this message]
2025-07-10 9:24 ` [PATCH v7 2/8] mfd: simple-mfd-i2c: specify max_register Lee Jones
2025-07-10 9:30 ` Lee Jones
2025-07-10 12:21 ` Alex Elder
2025-07-02 21:36 ` [PATCH v7 3/8] mfd: simple-mfd-i2c: add SpacemiT P1 support Alex Elder
2025-07-10 9:31 ` Lee Jones
2025-07-02 21:36 ` [PATCH v7 4/8] regulator: spacemit: support SpacemiT P1 regulators Alex Elder
2025-07-02 21:36 ` [PATCH v7 5/8] rtc: spacemit: support the SpacemiT P1 RTC Alex Elder
2025-07-02 21:36 ` [PATCH v7 6/8] riscv: dts: spacemit: enable the i2c8 adapter Alex Elder
2025-07-02 21:36 ` [PATCH v7 7/8] riscv: dts: spacemit: define fixed regulators Alex Elder
2025-07-02 21:36 ` [PATCH v7 8/8] riscv: dts: spacemit: define regulator constraints Alex Elder
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250702213658.545163-3-elder@riscstar.com \
--to=elder@riscstar.com \
--cc=alex@ghiti.fr \
--cc=alexandre.belloni@bootlin.com \
--cc=aou@eecs.berkeley.edu \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlan@gentoo.org \
--cc=guodong@riscstar.com \
--cc=krzk+dt@kernel.org \
--cc=lee@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=linux-rtc@vger.kernel.org \
--cc=mat.jonczyk@o2.pl \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh@kernel.org \
--cc=spacemit@lists.linux.dev \
--cc=troymitchell988@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox