[PATCH v10 0/8] spacemit: introduce P1 PMIC support

[PATCH v10 0/8] spacemit: introduce P1 PMIC support

[Alex Elder]

The SpacemiT P1 is an I2C-controlled PMIC that implements 6 buck
converters and 12 LDOs.  It contains a load switch, ADC channels,
GPIOs, a real-time clock, and a watchdog timer.

This series introduces a multifunction driver for the P1 PMIC as well
as drivers for its regulators and RTC.

This version makes a few minor changes to DTS files suggested by
Yixun Lan.  It also reworks the function that determines the
regmap_config structure to use, and adds a function that frees
that structure when it's no longer needed (if it was dynamically
allocated).

					-Alex

This series is available here:
  https://github.com/riscstar/linux/tree/outgoing/pmic-v10

Between version 9 and version 10:
  - The #address-cells and #size-cells for the i2c8 DTS node
    were moved into its primary definition in "k1.dtsi".
  - The interrupts property for the i2c8 DTS node was moved
    below its clock-related properties.
  - The status property in the pmic@41 DTS node was dropped.
  - The function that provides the regmap_config structure
    to use was reworked a bit.
  - A new function was added to free the regmap_config
    structure after it's no longer needed.

Here is version 9 of this series:
  https://lore.kernel.org/lkml/20250724202511.499288-1-elder@riscstar.com/

Between version 8 and version 9:
  - The max_config value is always used if it is provided with the
    simple_mfd_data structure.
  - The regmap_config structure used is allocated dynamically if
    necessary; otherwise regmap_config_8r_8v is used.
  - A small duplicated comment is removed

Here is version 8 of this series:
  https://lore.kernel.org/lkml/20250710175107.1280221-1-elder@riscstar.com/

More complete history is available at that link.

Alex Elder (8):
  dt-bindings: mfd: add support the SpacemiT P1 PMIC
  mfd: simple-mfd-i2c: specify max_register
  mfd: simple-mfd-i2c: add SpacemiT P1 support
  regulator: spacemit: support SpacemiT P1 regulators
  rtc: spacemit: support the SpacemiT P1 RTC
  riscv: dts: spacemit: enable the i2c8 adapter
  riscv: dts: spacemit: define fixed regulators
  riscv: dts: spacemit: define regulator constraints

 .../devicetree/bindings/mfd/spacemit,p1.yaml  |  86 +++++++++
 .../boot/dts/spacemit/k1-bananapi-f3.dts      | 135 ++++++++++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi  |   7 +
 arch/riscv/boot/dts/spacemit/k1.dtsi          |  13 ++
 drivers/mfd/Kconfig                           |  11 ++
 drivers/mfd/simple-mfd-i2c.c                  |  57 +++++-
 drivers/mfd/simple-mfd-i2c.h                  |   5 +-
 drivers/regulator/Kconfig                     |  12 ++
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/spacemit-p1.c               | 157 ++++++++++++++++
 drivers/rtc/Kconfig                           |  10 ++
 drivers/rtc/Makefile                          |   1 +
 drivers/rtc/rtc-spacemit-p1.c                 | 167 ++++++++++++++++++
 13 files changed, 653 insertions(+), 9 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
 create mode 100644 drivers/regulator/spacemit-p1.c
 create mode 100644 drivers/rtc/rtc-spacemit-p1.c


base-commit: d7af19298454ed155f5cf67201a70f5cf836c842
-- 
2.48.1

[PATCH v10 1/8] dt-bindings: mfd: add support the SpacemiT P1 PMIC

[Alex Elder]

Enable the SpacemiT P1, which is an I2C-controlled PMIC.  Initially
only the RTC and regulators will be supported.

Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../devicetree/bindings/mfd/spacemit,p1.yaml  | 86 +++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/spacemit,p1.yaml

diff --git a/Documentation/devicetree/bindings/mfd/spacemit,p1.yaml b/Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
new file mode 100644
index 0000000000000..5cc34d4934b54
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/spacemit,p1.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/spacemit,p1.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SpacemiT P1 Power Management Integrated Circuit
+
+maintainers:
+  - Troy Mitchell <troymitchell988@gmail.com>
+
+description:
+  P1 is an I2C-controlled PMIC produced by SpacemiT.  It implements six
+  constant-on-time buck converters and twelve low-dropout regulators.
+  It also contains a load switch, watchdog timer, real-time clock, eight
+  12-bit ADC channels, and six GPIOs.  Additional details are available
+  in the "Power Stone/P1" section at the following link.
+    https://developer.spacemit.com/documentation
+
+properties:
+  compatible:
+    const: spacemit,p1
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  vin-supply:
+    description: Input supply phandle.
+
+  regulators:
+    type: object
+
+    patternProperties:
+      "^(buck[1-6]|aldo[1-4]|dldo[1-7])$":
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+        unevaluatedProperties: false
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pmic@41 {
+            compatible = "spacemit,p1";
+            reg = <0x41>;
+            interrupts = <64>;
+
+            regulators {
+                buck1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <3450000>;
+                    regulator-ramp-delay = <5000>;
+                    regulator-always-on;
+                };
+
+                aldo1 {
+                    regulator-name = "aldo1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <3400000>;
+                    regulator-boot-on;
+                };
+
+                dldo1 {
+                    regulator-name = "dldo1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <3400000>;
+                    regulator-boot-on;
+                };
+            };
+        };
+    };
-- 
2.48.1

[PATCH v10 2/8] mfd: simple-mfd-i2c: specify max_register

[Alex Elder]

All devices supported by simple MFD use the same 8-bit register 8-bit
value regmap configuration.  There is an option available for a device
to specify a custom configuration, but no existing device uses it.

Rather than requiring a "full" regmap configuration to be provided to
change only the max_register value, Lee Jones suggested allowing
max_register to be specified in the simple_mfd_data structure.  The
8-bit register 8-bit configuration is still used by default, but
max_register is also applied if it is non-zero.

If both regmap_config and max_register are provided, the max_register
field in the regmap_config structure is ignored.

Signed-off-by: Alex Elder <elder@riscstar.com>
Suggested-by: Lee Jones <lee@kernel.org>
---
v10: - Rename simple_regmap_config() -> simple_regmap_config_get()
     - Introduce simple_regmap_config_put() to free regmap_config

 drivers/mfd/simple-mfd-i2c.c | 45 ++++++++++++++++++++++++++++++++----
 drivers/mfd/simple-mfd-i2c.h |  5 +---
 2 files changed, 41 insertions(+), 9 deletions(-)

diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
index 22159913bea03..3622f189c8342 100644
--- a/drivers/mfd/simple-mfd-i2c.c
+++ b/drivers/mfd/simple-mfd-i2c.c
@@ -29,6 +29,40 @@ static const struct regmap_config regmap_config_8r_8v = {
 	.val_bits = 8,
 };
 
+static const struct regmap_config *
+simple_regmap_config_get(const struct simple_mfd_data *data)
+{
+	struct regmap_config *regmap_config;
+	const struct regmap_config *source;
+
+	if (!data)
+		return &regmap_config_8r_8v;
+
+	source = data->regmap_config ? : &regmap_config_8r_8v;
+
+	if (!data->max_register)
+		return source;
+
+	regmap_config = kmemdup(source, sizeof(*regmap_config), GFP_KERNEL);
+	if (regmap_config)
+		regmap_config->max_register = data->max_register;
+
+	return regmap_config;
+}
+
+static void simple_regmap_config_put(const struct simple_mfd_data *data,
+				     const struct regmap_config *regmap_config)
+{
+	/* This condition holds if data is null */
+	if (regmap_config == &regmap_config_8r_8v)
+		return;
+
+	if (regmap_config == data->regmap_config)
+		return;
+
+	kfree(regmap_config);
+}
+
 static int simple_mfd_i2c_probe(struct i2c_client *i2c)
 {
 	const struct simple_mfd_data *simple_mfd_data;
@@ -38,13 +72,14 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c)
 
 	simple_mfd_data = device_get_match_data(&i2c->dev);
 
-	/* If no regmap_config is specified, use the default 8reg and 8val bits */
-	if (!simple_mfd_data || !simple_mfd_data->regmap_config)
-		regmap_config = &regmap_config_8r_8v;
-	else
-		regmap_config = simple_mfd_data->regmap_config;
+	regmap_config = simple_regmap_config_get(simple_mfd_data);
+	if (!regmap_config)
+		return -ENOMEM;
 
 	regmap = devm_regmap_init_i2c(i2c, regmap_config);
+
+	simple_regmap_config_put(simple_mfd_data, regmap_config);
+
 	if (IS_ERR(regmap))
 		return PTR_ERR(regmap);
 
diff --git a/drivers/mfd/simple-mfd-i2c.h b/drivers/mfd/simple-mfd-i2c.h
index 7cb2bdd347d97..6fa36b3d7a217 100644
--- a/drivers/mfd/simple-mfd-i2c.h
+++ b/drivers/mfd/simple-mfd-i2c.h
@@ -8,10 +8,6 @@
  * shared by all sub-devices.  Children can use their parent's device structure
  * (dev.parent) in order to reference it.
  *
- * This driver creates a single register map with the intention for it to be
- * shared by all sub-devices.  Children can use their parent's device structure
- * (dev.parent) in order to reference it.
- *
  * Once the register map has been successfully initialised, any sub-devices
  * represented by child nodes in Device Tree or via the MFD cells in the
  * associated C file will be subsequently registered.
@@ -25,6 +21,7 @@
 
 struct simple_mfd_data {
 	const struct regmap_config *regmap_config;
+	unsigned int max_register;
 	const struct mfd_cell *mfd_cell;
 	size_t mfd_cell_size;
 };
-- 
2.48.1

Re: [PATCH v10 2/8] mfd: simple-mfd-i2c: specify max_register

[Lee Jones]

On Sat, 26 Jul 2025, Alex Elder wrote:

> All devices supported by simple MFD use the same 8-bit register 8-bit
> value regmap configuration.  There is an option available for a device
> to specify a custom configuration, but no existing device uses it.
> 
> Rather than requiring a "full" regmap configuration to be provided to
> change only the max_register value, Lee Jones suggested allowing
> max_register to be specified in the simple_mfd_data structure.  The
> 8-bit register 8-bit configuration is still used by default, but
> max_register is also applied if it is non-zero.
> 
> If both regmap_config and max_register are provided, the max_register
> field in the regmap_config structure is ignored.
> 
> Signed-off-by: Alex Elder <elder@riscstar.com>
> Suggested-by: Lee Jones <lee@kernel.org>
> ---
> v10: - Rename simple_regmap_config() -> simple_regmap_config_get()
>      - Introduce simple_regmap_config_put() to free regmap_config
> 
>  drivers/mfd/simple-mfd-i2c.c | 45 ++++++++++++++++++++++++++++++++----
>  drivers/mfd/simple-mfd-i2c.h |  5 +---
>  2 files changed, 41 insertions(+), 9 deletions(-)

This has gone from an in-function 11 line change to 50 lines and the
inclusion of 2 new functions.  As much as I _really_ appreciate the time
and effort you have put into this [0], the added complexity being added
here doesn't sit right with me.  How would you like to go back to your
v4 idea of providing a bespoke regmap_config for for device?

[0] Beers on me for sending you down this path!

-- 
Lee Jones [李琼斯]

Re: [PATCH v10 2/8] mfd: simple-mfd-i2c: specify max_register

[Alex Elder]

On 7/31/25 8:18 AM, Lee Jones wrote:
> On Sat, 26 Jul 2025, Alex Elder wrote:
> 
>> All devices supported by simple MFD use the same 8-bit register 8-bit
>> value regmap configuration.  There is an option available for a device
>> to specify a custom configuration, but no existing device uses it.
>>
>> Rather than requiring a "full" regmap configuration to be provided to
>> change only the max_register value, Lee Jones suggested allowing
>> max_register to be specified in the simple_mfd_data structure.  The
>> 8-bit register 8-bit configuration is still used by default, but
>> max_register is also applied if it is non-zero.
>>
>> If both regmap_config and max_register are provided, the max_register
>> field in the regmap_config structure is ignored.
>>
>> Signed-off-by: Alex Elder <elder@riscstar.com>
>> Suggested-by: Lee Jones <lee@kernel.org>
>> ---
>> v10: - Rename simple_regmap_config() -> simple_regmap_config_get()
>>       - Introduce simple_regmap_config_put() to free regmap_config
>>
>>   drivers/mfd/simple-mfd-i2c.c | 45 ++++++++++++++++++++++++++++++++----
>>   drivers/mfd/simple-mfd-i2c.h |  5 +---
>>   2 files changed, 41 insertions(+), 9 deletions(-)
> 
> This has gone from an in-function 11 line change to 50 lines and the
> inclusion of 2 new functions.  As much as I _really_ appreciate the time
> and effort you have put into this [0], the added complexity being added
> here doesn't sit right with me.  How would you like to go back to your
> v4 idea of providing a bespoke regmap_config for for device?

I LOVE this suggestion.  I will send v11 shortly and it will
be very much like v6 (or something like that).

> [0] Beers on me for sending you down this path!

I'm looking forward to seeing you again, beer or not.

Thanks Lee.

					-Alex

Re: [PATCH v10 2/8] mfd: simple-mfd-i2c: specify max_register

[Lee Jones]

On Thu, 31 Jul 2025, Alex Elder wrote:

> On 7/31/25 8:18 AM, Lee Jones wrote:
> > On Sat, 26 Jul 2025, Alex Elder wrote:
> > 
> > > All devices supported by simple MFD use the same 8-bit register 8-bit
> > > value regmap configuration.  There is an option available for a device
> > > to specify a custom configuration, but no existing device uses it.
> > > 
> > > Rather than requiring a "full" regmap configuration to be provided to
> > > change only the max_register value, Lee Jones suggested allowing
> > > max_register to be specified in the simple_mfd_data structure.  The
> > > 8-bit register 8-bit configuration is still used by default, but
> > > max_register is also applied if it is non-zero.
> > > 
> > > If both regmap_config and max_register are provided, the max_register
> > > field in the regmap_config structure is ignored.
> > > 
> > > Signed-off-by: Alex Elder <elder@riscstar.com>
> > > Suggested-by: Lee Jones <lee@kernel.org>
> > > ---
> > > v10: - Rename simple_regmap_config() -> simple_regmap_config_get()
> > >       - Introduce simple_regmap_config_put() to free regmap_config
> > > 
> > >   drivers/mfd/simple-mfd-i2c.c | 45 ++++++++++++++++++++++++++++++++----
> > >   drivers/mfd/simple-mfd-i2c.h |  5 +---
> > >   2 files changed, 41 insertions(+), 9 deletions(-)
> > 
> > This has gone from an in-function 11 line change to 50 lines and the
> > inclusion of 2 new functions.  As much as I _really_ appreciate the time
> > and effort you have put into this [0], the added complexity being added
> > here doesn't sit right with me.  How would you like to go back to your
> > v4 idea of providing a bespoke regmap_config for for device?
> 
> I LOVE this suggestion.  I will send v11 shortly and it will
> be very much like v6 (or something like that).
> 
> > [0] Beers on me for sending you down this path!
> 
> I'm looking forward to seeing you again, beer or not.

Likewise!  =:-)

-- 
Lee Jones [李琼斯]

[PATCH v10 3/8] mfd: simple-mfd-i2c: add SpacemiT P1 support

[Alex Elder]

Enable support for the RTC and regulators found in the SpacemiT P1
PMIC.  Support is implemented by the simple I2C MFD driver.

The P1 PMIC is normally implemented with the SpacemiT K1 SoC.  This
PMIC provides 6 buck converters and 12 LDO regulators.  It also
implements a switch, watchdog timer, real-time clock, and more.
Initially its RTC and regulators are supported.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 drivers/mfd/Kconfig          | 11 +++++++++++
 drivers/mfd/simple-mfd-i2c.c | 12 ++++++++++++
 2 files changed, 23 insertions(+)

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8f11b2df14704..3fe242ffcb31d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1238,6 +1238,17 @@ config MFD_QCOM_RPM
 	  Say M here if you want to include support for the Qualcomm RPM as a
 	  module. This will build a module called "qcom_rpm".
 
+config MFD_SPACEMIT_P1
+	tristate "SpacemiT P1 PMIC"
+	depends on I2C
+	select MFD_SIMPLE_MFD_I2C
+	help
+	  This option supports the I2C-based SpacemiT P1 PMIC, which
+	  contains regulators, a power switch, GPIOs, an RTC, and more.
+	  This option is selected when any of the supported sub-devices
+	  is configured.  The basic functionality is implemented by the
+	  simple MFD I2C driver.
+
 config MFD_SPMI_PMIC
 	tristate "Qualcomm SPMI PMICs"
 	depends on ARCH_QCOM || COMPILE_TEST
diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c
index 3622f189c8342..34c69ef4a7e94 100644
--- a/drivers/mfd/simple-mfd-i2c.c
+++ b/drivers/mfd/simple-mfd-i2c.c
@@ -128,12 +128,24 @@ static const struct simple_mfd_data maxim_mon_max77705 = {
 	.mfd_cell_size = ARRAY_SIZE(max77705_sensor_cells),
 };
 
+static const struct mfd_cell spacemit_p1_cells[] = {
+	{ .name = "spacemit-p1-regulator", },
+	{ .name = "spacemit-p1-rtc", },
+};
+
+static const struct simple_mfd_data spacemit_p1 = {
+	.mfd_cell = spacemit_p1_cells,
+	.mfd_cell_size = ARRAY_SIZE(spacemit_p1_cells),
+	.max_register = 0xaa,
+};
+
 static const struct of_device_id simple_mfd_i2c_of_match[] = {
 	{ .compatible = "kontron,sl28cpld" },
 	{ .compatible = "silergy,sy7636a", .data = &silergy_sy7636a},
 	{ .compatible = "maxim,max5970", .data = &maxim_max5970},
 	{ .compatible = "maxim,max5978", .data = &maxim_max5970},
 	{ .compatible = "maxim,max77705-battery", .data = &maxim_mon_max77705},
+	{ .compatible = "spacemit,p1", .data = &spacemit_p1, },
 	{}
 };
 MODULE_DEVICE_TABLE(of, simple_mfd_i2c_of_match);
-- 
2.48.1

[PATCH v10 4/8] regulator: spacemit: support SpacemiT P1 regulators

[Alex Elder]

Add support for the regulators found in the SpacemiT P1 PMIC.  This
PMIC provides 6 buck converters and 12 LDO regulators.

The PMIC is implemented as a multi-function device.  These regulators
are probed based on this driver being named in a MFD cell in the simple
MFD I2C driver.

Signed-off-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/Kconfig       |  12 +++
 drivers/regulator/Makefile      |   1 +
 drivers/regulator/spacemit-p1.c | 157 ++++++++++++++++++++++++++++++++
 3 files changed, 170 insertions(+)
 create mode 100644 drivers/regulator/spacemit-p1.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index eaa6df1c9f806..7d5f79a468761 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1395,6 +1395,18 @@ config REGULATOR_SLG51000
 	  The SLG51000 is seven compact and customizable low dropout
 	  regulators.
 
+config REGULATOR_SPACEMIT_P1
+	tristate "SpacemiT P1 regulators"
+	depends on ARCH_SPACEMIT || COMPILE_TEST
+	select MFD_SPACEMIT_P1
+	default ARCH_SPACEMIT
+	help
+	  Enable support for regulators implemented by the SpacemiT P1
+	  power controller.  The P1 implements 6 high-efficiency buck
+	  converters and 12 programmable LDO regulators.  To compile this
+	  driver as a module, choose M here.  The module will be called
+	  "spacemit-pmic".
+
 config REGULATOR_STM32_BOOSTER
 	tristate "STMicroelectronics STM32 BOOSTER"
 	depends on ARCH_STM32 || COMPILE_TEST
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index be98b29d6675d..278f5b8d1c7d7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -162,6 +162,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
 obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
 obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
 obj-$(CONFIG_REGULATOR_SLG51000) += slg51000-regulator.o
+obj-$(CONFIG_REGULATOR_SPACEMIT_P1) += spacemit-p1.o
 obj-$(CONFIG_REGULATOR_STM32_BOOSTER) += stm32-booster.o
 obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
 obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o
diff --git a/drivers/regulator/spacemit-p1.c b/drivers/regulator/spacemit-p1.c
new file mode 100644
index 0000000000000..d437e6738ea1e
--- /dev/null
+++ b/drivers/regulator/spacemit-p1.c
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for regulators found in the SpacemiT P1 PMIC
+ *
+ * Copyright (C) 2025 by RISCstar Solutions Corporation.  All rights reserved.
+ * Derived from code from SpacemiT.
+ *	Copyright (c) 2023, SPACEMIT Co., Ltd
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/linear_range.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+
+#define MOD_NAME	"spacemit-p1-regulator"
+
+enum p1_regulator_id {
+	P1_BUCK1,
+	P1_BUCK2,
+	P1_BUCK3,
+	P1_BUCK4,
+	P1_BUCK5,
+	P1_BUCK6,
+
+	P1_ALDO1,
+	P1_ALDO2,
+	P1_ALDO3,
+	P1_ALDO4,
+
+	P1_DLDO1,
+	P1_DLDO2,
+	P1_DLDO3,
+	P1_DLDO4,
+	P1_DLDO5,
+	P1_DLDO6,
+	P1_DLDO7,
+};
+
+static const struct regulator_ops p1_regulator_ops = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel   = regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+};
+
+/* Selector value 255 can be used to disable the buck converter on sleep */
+static const struct linear_range p1_buck_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000, 0, 170, 5000),
+	REGULATOR_LINEAR_RANGE(1375000, 171, 254, 25000),
+};
+
+/* Selector value 0 can be used for suspend */
+static const struct linear_range p1_ldo_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000, 11, 127, 25000),
+};
+
+/* These define the voltage selector field for buck and LDO regulators */
+#define BUCK_MASK		GENMASK(7, 0)
+#define LDO_MASK		GENMASK(6, 0)
+
+#define P1_ID(_TYPE, _n)	P1_ ## _TYPE ## _n
+#define P1_ENABLE_REG(_off, _n)	((_off) + 3 * ((_n) - 1))
+
+#define P1_REG_DESC(_TYPE, _type, _n, _s, _off, _mask, _nv, _ranges)	\
+	{								\
+		.name			= #_type #_n,			\
+		.supply_name		= _s,				\
+		.of_match		= of_match_ptr(#_type #_n),	\
+		.regulators_node	= of_match_ptr("regulators"),	\
+		.id			= P1_ID(_TYPE, _n),		\
+		.n_voltages		= _nv,				\
+		.ops			= &p1_regulator_ops,		\
+		.owner			= THIS_MODULE,			\
+		.linear_ranges		= _ranges,			\
+		.n_linear_ranges	= ARRAY_SIZE(_ranges),		\
+		.vsel_reg		= P1_ENABLE_REG(_off, _n) + 1,	\
+		.vsel_mask		= _mask,			\
+		.enable_reg		= P1_ENABLE_REG(_off, _n),	\
+		.enable_mask		= BIT(0),			\
+	}
+
+#define P1_BUCK_DESC(_n) \
+	P1_REG_DESC(BUCK, buck, _n, "vcc", 0x47, BUCK_MASK, 254, p1_buck_ranges)
+
+#define P1_ALDO_DESC(_n) \
+	P1_REG_DESC(ALDO, aldo, _n, "vcc", 0x5b, LDO_MASK, 117, p1_ldo_ranges)
+
+#define P1_DLDO_DESC(_n) \
+	P1_REG_DESC(DLDO, dldo, _n, "buck5", 0x67, LDO_MASK, 117, p1_ldo_ranges)
+
+static const struct regulator_desc p1_regulator_desc[] = {
+	P1_BUCK_DESC(1),
+	P1_BUCK_DESC(2),
+	P1_BUCK_DESC(3),
+	P1_BUCK_DESC(4),
+	P1_BUCK_DESC(5),
+	P1_BUCK_DESC(6),
+
+	P1_ALDO_DESC(1),
+	P1_ALDO_DESC(2),
+	P1_ALDO_DESC(3),
+	P1_ALDO_DESC(4),
+
+	P1_DLDO_DESC(1),
+	P1_DLDO_DESC(2),
+	P1_DLDO_DESC(3),
+	P1_DLDO_DESC(4),
+	P1_DLDO_DESC(5),
+	P1_DLDO_DESC(6),
+	P1_DLDO_DESC(7),
+};
+
+static int p1_regulator_probe(struct platform_device *pdev)
+{
+	struct regulator_config config = { };
+	struct device *dev = &pdev->dev;
+	u32 i;
+
+	/*
+	 * The parent device (PMIC) owns the regmap.  Since we don't
+	 * provide one in the config structure, that one will be used.
+	 */
+	config.dev = dev->parent;
+
+	for (i = 0; i < ARRAY_SIZE(p1_regulator_desc); i++) {
+		const struct regulator_desc *desc = &p1_regulator_desc[i];
+		struct regulator_dev *rdev;
+
+		rdev = devm_regulator_register(dev, desc, &config);
+		if (IS_ERR(rdev))
+			return dev_err_probe(dev, PTR_ERR(rdev),
+					     "error registering regulator %s\n",
+					     desc->name);
+	}
+
+	return 0;
+}
+
+static struct platform_driver p1_regulator_driver = {
+	.probe = p1_regulator_probe,
+	.driver = {
+		.name = MOD_NAME,
+	},
+};
+
+module_platform_driver(p1_regulator_driver);
+
+MODULE_DESCRIPTION("SpacemiT P1 regulator driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" MOD_NAME);
-- 
2.48.1

Re: [PATCH v10 4/8] regulator: spacemit: support SpacemiT P1 regulators

[kernel test robot]

Hi Alex,

kernel test robot noticed the following build warnings:

[auto build test WARNING on d7af19298454ed155f5cf67201a70f5cf836c842]

url:    https://github.com/intel-lab-lkp/linux/commits/Alex-Elder/dt-bindings-mfd-add-support-the-SpacemiT-P1-PMIC/20250726-211530
base:   d7af19298454ed155f5cf67201a70f5cf836c842
patch link:    https://lore.kernel.org/r/20250726131003.3137282-5-elder%40riscstar.com
patch subject: [PATCH v10 4/8] regulator: spacemit: support SpacemiT P1 regulators
config: alpha-kismet-CONFIG_MFD_SPACEMIT_P1-CONFIG_REGULATOR_SPACEMIT_P1-0-0 (https://download.01.org/0day-ci/archive/20250728/202507281558.lZ0NYtth-lkp@intel.com/config)
reproduce: (https://download.01.org/0day-ci/archive/20250728/202507281558.lZ0NYtth-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202507281558.lZ0NYtth-lkp@intel.com/

kismet warnings: (new ones prefixed by >>)
>> kismet: WARNING: unmet direct dependencies detected for MFD_SPACEMIT_P1 when selected by REGULATOR_SPACEMIT_P1
   WARNING: unmet direct dependencies detected for MFD_SPACEMIT_P1
     Depends on [n]: HAS_IOMEM [=y] && I2C [=n]
     Selected by [y]:
     - REGULATOR_SPACEMIT_P1 [=y] && REGULATOR [=y] && (ARCH_SPACEMIT || COMPILE_TEST [=y])

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

Re: [PATCH v10 4/8] regulator: spacemit: support SpacemiT P1 regulators

[Alex Elder]

On 7/28/25 2:37 AM, kernel test robot wrote:
> Hi Alex,
> 
> kernel test robot noticed the following build warnings:

I have a fix for this, and will include it in v11 of this series
when I publish it.  I will wait to do that until I get additional
feedback.

The fix is to make REGULATOR_SPACEMIT_P1 depend on I2C, in addition
to ARCH_SPACEMIT || COMPILE_TEST.

					-Alex

> 
> [auto build test WARNING on d7af19298454ed155f5cf67201a70f5cf836c842]
> 
> url:    https://github.com/intel-lab-lkp/linux/commits/Alex-Elder/dt-bindings-mfd-add-support-the-SpacemiT-P1-PMIC/20250726-211530
> base:   d7af19298454ed155f5cf67201a70f5cf836c842
> patch link:    https://lore.kernel.org/r/20250726131003.3137282-5-elder%40riscstar.com
> patch subject: [PATCH v10 4/8] regulator: spacemit: support SpacemiT P1 regulators
> config: alpha-kismet-CONFIG_MFD_SPACEMIT_P1-CONFIG_REGULATOR_SPACEMIT_P1-0-0 (https://download.01.org/0day-ci/archive/20250728/202507281558.lZ0NYtth-lkp@intel.com/config)
> reproduce: (https://download.01.org/0day-ci/archive/20250728/202507281558.lZ0NYtth-lkp@intel.com/reproduce)
> 
> If you fix the issue in a separate patch/commit (i.e. not just a new version of
> the same patch/commit), kindly add following tags
> | Reported-by: kernel test robot <lkp@intel.com>
> | Closes: https://lore.kernel.org/oe-kbuild-all/202507281558.lZ0NYtth-lkp@intel.com/
> 
> kismet warnings: (new ones prefixed by >>)
>>> kismet: WARNING: unmet direct dependencies detected for MFD_SPACEMIT_P1 when selected by REGULATOR_SPACEMIT_P1
>     WARNING: unmet direct dependencies detected for MFD_SPACEMIT_P1
>       Depends on [n]: HAS_IOMEM [=y] && I2C [=n]
>       Selected by [y]:
>       - REGULATOR_SPACEMIT_P1 [=y] && REGULATOR [=y] && (ARCH_SPACEMIT || COMPILE_TEST [=y])
> 

[PATCH v10 5/8] rtc: spacemit: support the SpacemiT P1 RTC

[Alex Elder]

Add support for the RTC found in the SpacemiT P1 PMIC.  Initially
only setting and reading the time are supported.

The PMIC is implemented as a multi-function device.  This RTC is
probed based on this driver being named in a MFD cell in the simple
MFD I2C driver.

Signed-off-by: Alex Elder <elder@riscstar.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 drivers/rtc/Kconfig           |  10 ++
 drivers/rtc/Makefile          |   1 +
 drivers/rtc/rtc-spacemit-p1.c | 167 ++++++++++++++++++++++++++++++++++
 3 files changed, 178 insertions(+)
 create mode 100644 drivers/rtc/rtc-spacemit-p1.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 64f6e9756aff4..31d355b103d43 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -406,6 +406,16 @@ config RTC_DRV_MAX77686
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-max77686.
 
+config RTC_DRV_SPACEMIT_P1
+	tristate "SpacemiT P1 RTC"
+	depends on ARCH_SPACEMIT || COMPILE_TEST
+	select MFD_SPACEMIT_P1
+	default ARCH_SPACEMIT
+	help
+	  Enable support for the RTC function in the SpacemiT P1 PMIC.
+	  This driver can also be built as a module, which will be called
+	  "spacemit-p1-rtc".
+
 config RTC_DRV_NCT3018Y
 	tristate "Nuvoton NCT3018Y"
 	depends on OF
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 789bddfea99d8..f41fdb4fabae9 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -171,6 +171,7 @@ obj-$(CONFIG_RTC_DRV_SD2405AL)	+= rtc-sd2405al.o
 obj-$(CONFIG_RTC_DRV_SD3078)	+= rtc-sd3078.o
 obj-$(CONFIG_RTC_DRV_SH)	+= rtc-sh.o
 obj-$(CONFIG_RTC_DRV_SNVS)	+= rtc-snvs.o
+obj-$(CONFIG_RTC_DRV_SPACEMIT_P1)	+= rtc-spacemit-p1.o
 obj-$(CONFIG_RTC_DRV_SPEAR)	+= rtc-spear.o
 obj-$(CONFIG_RTC_DRV_STARFIRE)	+= rtc-starfire.o
 obj-$(CONFIG_RTC_DRV_STK17TA8)	+= rtc-stk17ta8.o
diff --git a/drivers/rtc/rtc-spacemit-p1.c b/drivers/rtc/rtc-spacemit-p1.c
new file mode 100644
index 0000000000000..43ab62494bb4b
--- /dev/null
+++ b/drivers/rtc/rtc-spacemit-p1.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the RTC found in the SpacemiT P1 PMIC
+ *
+ * Copyright (C) 2025 by RISCstar Solutions Corporation.  All rights reserved.
+ */
+
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/rtc.h>
+
+#define MOD_NAME	"spacemit-p1-rtc"
+
+/*
+ * Six consecutive 1-byte registers hold the seconds, minutes, hours,
+ * day-of-month, month, and year (respectively).
+ *
+ * The range of values in these registers is:
+ *    seconds	0-59
+ *    minutes	0-59
+ *    hours	0-59
+ *    day	0-30 (struct tm is 1-31)
+ *    month	0-11
+ *    year	years since 2000 (struct tm is since 1900)
+ *
+ * Note that the day and month must be converted after reading and
+ * before writing.
+ */
+#define RTC_TIME		0x0d	/* Offset of the seconds register */
+
+#define RTC_CTRL		0x1d
+#define RTC_EN		BIT(2)
+
+/* Number of attempts to read a consistent time stamp before giving up */
+#define RTC_READ_TRIES		20	/* At least 1 */
+
+struct p1_rtc {
+	struct regmap *regmap;
+	struct rtc_device *rtc;
+};
+
+/*
+ * The P1 hardware documentation states that the register values are
+ * latched to ensure a consistent time snapshot within the registers,
+ * but these are in fact unstable due to a bug in the hardware design.
+ * So we loop until we get two identical readings.
+ */
+static int p1_rtc_read_time(struct device *dev, struct rtc_time *t)
+{
+	struct p1_rtc *p1 = dev_get_drvdata(dev);
+	struct regmap *regmap = p1->regmap;
+	u32 count = RTC_READ_TRIES;
+	u8 seconds;
+	u8 time[6];
+	int ret;
+
+	if (!regmap_test_bits(regmap, RTC_CTRL, RTC_EN))
+		return -EINVAL;		/* RTC is disabled */
+
+	ret = regmap_bulk_read(regmap, RTC_TIME, time, sizeof(time));
+	if (ret)
+		return ret;
+
+	do {
+		seconds = time[0];
+		ret = regmap_bulk_read(regmap, RTC_TIME, time, sizeof(time));
+		if (ret)
+			return ret;
+	} while (time[0] != seconds && --count);
+
+	if (!count)
+		return -EIO;		/* Unable to get a consistent result */
+
+	t->tm_sec = time[0] & GENMASK(5, 0);
+	t->tm_min = time[1] & GENMASK(5, 0);
+	t->tm_hour = time[2] & GENMASK(4, 0);
+	t->tm_mday = (time[3] & GENMASK(4, 0)) + 1;
+	t->tm_mon = time[4] & GENMASK(3, 0);
+	t->tm_year = (time[5] & GENMASK(5, 0)) + 100;
+
+	return 0;
+}
+
+/*
+ * The P1 hardware documentation states that values in the registers are
+ * latched so when written they represent a consistent time snapshot.
+ * Nevertheless, this is not guaranteed by the implementation, so we must
+ * disable the RTC while updating it.
+ */
+static int p1_rtc_set_time(struct device *dev, struct rtc_time *t)
+{
+	struct p1_rtc *p1 = dev_get_drvdata(dev);
+	struct regmap *regmap = p1->regmap;
+	u8 time[6];
+	int ret;
+
+	time[0] = t->tm_sec;
+	time[1] = t->tm_min;
+	time[2] = t->tm_hour;
+	time[3] = t->tm_mday - 1;
+	time[4] = t->tm_mon;
+	time[5] = t->tm_year - 100;
+
+	/* Disable the RTC to update; re-enable again when done */
+	ret = regmap_clear_bits(regmap, RTC_CTRL, RTC_EN);
+	if (ret)
+		return ret;
+
+	/* If something goes wrong, leave the RTC disabled */
+	ret = regmap_bulk_write(regmap, RTC_TIME, time, sizeof(time));
+	if (ret)
+		return ret;
+
+	return regmap_set_bits(regmap, RTC_CTRL, RTC_EN);
+}
+
+static const struct rtc_class_ops p1_rtc_class_ops = {
+	.read_time = p1_rtc_read_time,
+	.set_time = p1_rtc_set_time,
+};
+
+static int p1_rtc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rtc_device *rtc;
+	struct p1_rtc *p1;
+
+	p1 = devm_kzalloc(dev, sizeof(*p1), GFP_KERNEL);
+	if (!p1)
+		return -ENOMEM;
+	dev_set_drvdata(dev, p1);
+
+	p1->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!p1->regmap)
+		return dev_err_probe(dev, -ENODEV, "failed to get regmap\n");
+
+	rtc = devm_rtc_allocate_device(dev);
+	if (IS_ERR(rtc))
+		return dev_err_probe(dev, PTR_ERR(rtc),
+				     "error allocating device\n");
+	p1->rtc = rtc;
+
+	rtc->ops = &p1_rtc_class_ops;
+	rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
+	rtc->range_max = RTC_TIMESTAMP_END_2063;
+
+	clear_bit(RTC_FEATURE_ALARM, rtc->features);
+	clear_bit(RTC_FEATURE_UPDATE_INTERRUPT, rtc->features);
+
+	return devm_rtc_register_device(rtc);
+}
+
+static struct platform_driver p1_rtc_driver = {
+	.probe = p1_rtc_probe,
+	.driver = {
+		.name = MOD_NAME,
+	},
+};
+
+module_platform_driver(p1_rtc_driver);
+
+MODULE_DESCRIPTION("SpacemiT P1 RTC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" MOD_NAME);
-- 
2.48.1

[PATCH v10 6/8] riscv: dts: spacemit: enable the i2c8 adapter

[Alex Elder]

Define properties for the I2C adapter that provides access to the
SpacemiT P1 PMIC.  Enable this adapter on the Banana Pi BPI-F3.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
v10: - Move a few things around as suggested by Yixun Lan

 arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 12 ++++++++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi    |  7 +++++++
 arch/riscv/boot/dts/spacemit/k1.dtsi            | 13 +++++++++++++
 3 files changed, 32 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index fe22c747c5012..ae9409fe398b2 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -40,6 +40,18 @@ &emmc {
 	status = "okay";
 };
 
+&i2c8 {
+	pinctrl-0 = <&i2c8_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pmic@41 {
+		compatible = "spacemit,p1";
+		reg = <0x41>;
+		interrupts = <64>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
index 3810557374228..96d7a46d4bf77 100644
--- a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
@@ -11,6 +11,13 @@
 #define K1_GPIO(x)	(x / 32) (x % 32)
 
 &pinctrl {
+	i2c8_cfg: i2c8-cfg {
+		i2c8-0-pins {
+			pinmux = <K1_PADCONF(93, 0)>,	/* PWR_SCL */
+				 <K1_PADCONF(94, 0)>;	/* PWR_SDA */
+		};
+	};
+
 	uart0_2_cfg: uart0-2-cfg {
 		uart0-2-pins {
 			pinmux = <K1_PADCONF(68, 2)>,
diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
index abde8bb07c95c..580f77b5e838a 100644
--- a/arch/riscv/boot/dts/spacemit/k1.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
@@ -459,6 +459,19 @@ pwm7: pwm@d401bc00 {
 			status = "disabled";
 		};
 
+		i2c8: i2c@d401d800 {
+			compatible = "spacemit,k1-i2c";
+			reg = <0x0 0xd401d800 0x0 0x38>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&syscon_apbc CLK_TWSI8>,
+				 <&syscon_apbc CLK_TWSI8_BUS>;
+			clock-names = "func", "bus";
+			clock-frequency = <400000>;
+			interrupts = <19>;
+			status = "disabled";
+		};
+
 		pinctrl: pinctrl@d401e000 {
 			compatible = "spacemit,k1-pinctrl";
 			reg = <0x0 0xd401e000 0x0 0x400>;
-- 
2.48.1

[PATCH v10 7/8] riscv: dts: spacemit: define fixed regulators

[Alex Elder]

Define the DC power input and the 4v power as fixed supplies in the
Banana Pi BPI-F3.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 .../boot/dts/spacemit/k1-bananapi-f3.dts      | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index ae9409fe398b2..a11a60b9f369b 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -28,6 +28,25 @@ led1 {
 			default-state = "on";
 		};
 	};
+
+	reg_dc_in: dc-in-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_in_12v";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_vcc_4v: vcc-4v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_4v";
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&reg_dc_in>;
+	};
 };
 
 &emmc {
-- 
2.48.1

[PATCH v10 8/8] riscv: dts: spacemit: define regulator constraints

[Alex Elder]

Define basic constraints for the regulators in the SpacemiT P1 PMIC,
as implemented in the Banana Pi BPI-F3.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 .../boot/dts/spacemit/k1-bananapi-f3.dts      | 104 ++++++++++++++++++
 1 file changed, 104 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index a11a60b9f369b..a9a2596a94e89 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -68,6 +68,110 @@ pmic@41 {
 		compatible = "spacemit,p1";
 		reg = <0x41>;
 		interrupts = <64>;
+		vin-supply = <&reg_vcc_4v>;
+
+		regulators {
+			buck1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			aldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			aldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			dldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo7 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
 	};
 };
 
-- 
2.48.1