From: Kaustabh Chakraborty <kauschluss@disroot.org>
To: "Lee Jones" <lee@kernel.org>, "Pavel Machek" <pavel@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"MyungJoo Ham" <myungjoo.ham@samsung.com>,
"Chanwoo Choi" <cw00.choi@samsung.com>,
"Sebastian Reichel" <sre@kernel.org>,
"Krzysztof Kozlowski" <krzk@kernel.org>,
"André Draszik" <andre.draszik@linaro.org>,
"Alexandre Belloni" <alexandre.belloni@bootlin.com>,
"Jonathan Corbet" <corbet@lwn.net>,
"Shuah Khan" <skhan@linuxfoundation.org>,
"Nam Tran" <trannamatk@gmail.com>,
"Łukasz Lebiedziński" <kernel@lvkasz.us>
Cc: linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org,
linux-samsung-soc@vger.kernel.org, linux-rtc@vger.kernel.org,
linux-doc@vger.kernel.org,
Kaustabh Chakraborty <kauschluss@disroot.org>
Subject: [PATCH v4 09/13] leds: flash: add support for Samsung S2M series PMIC flash LED device
Date: Tue, 14 Apr 2026 12:03:01 +0530 [thread overview]
Message-ID: <20260414-s2mu005-pmic-v4-9-7fe7480577e6@disroot.org> (raw)
In-Reply-To: <20260414-s2mu005-pmic-v4-0-7fe7480577e6@disroot.org>
Add support for flash LEDs found in certain Samsung S2M series PMICs.
The device has two channels for LEDs, typically for the back and front
cameras in mobile devices. Both channels can be independently
controlled, and can be operated in torch or flash modes.
The driver includes initial support for the S2MU005 PMIC flash LEDs.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/leds/flash/Kconfig | 12 ++
drivers/leds/flash/Makefile | 1 +
drivers/leds/flash/leds-s2m-flash.c | 357 ++++++++++++++++++++++++++++++++++++
3 files changed, 370 insertions(+)
diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig
index 5e08102a67841..be62e05277429 100644
--- a/drivers/leds/flash/Kconfig
+++ b/drivers/leds/flash/Kconfig
@@ -114,6 +114,18 @@ config LEDS_RT8515
To compile this driver as a module, choose M here: the module
will be called leds-rt8515.
+config LEDS_S2M_FLASH
+ tristate "Samsung S2M series PMICs flash/torch LED support"
+ depends on LEDS_CLASS
+ depends on MFD_SEC_CORE
+ depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
+ select REGMAP_IRQ
+ help
+ This option enables support for the flash/torch LEDs found in
+ certain Samsung S2M series PMICs, such as the S2MU005. It has
+ a LED channel dedicated for every physical LED. The LEDs can
+ be controlled in flash and torch modes.
+
config LEDS_SGM3140
tristate "LED support for the SGM3140"
depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile
index 712fb737a428e..44e6c1b4beb37 100644
--- a/drivers/leds/flash/Makefile
+++ b/drivers/leds/flash/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_LEDS_MAX77693) += leds-max77693.o
obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-flash.o
obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o
obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o
+obj-$(CONFIG_LEDS_S2M_FLASH) += leds-s2m-flash.o
obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o
obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o
obj-$(CONFIG_LEDS_TPS6131X) += leds-tps6131x.o
diff --git a/drivers/leds/flash/leds-s2m-flash.c b/drivers/leds/flash/leds-s2m-flash.c
new file mode 100644
index 0000000000000..1ec592417c344
--- /dev/null
+++ b/drivers/leds/flash/leds-s2m-flash.c
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Flash and Torch LED Driver for Samsung S2M series PMICs.
+ *
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (c) 2025 Kaustabh Chakraborty <kauschluss@disroot.org>
+ */
+
+#include <linux/container_of.h>
+#include <linux/led-class-flash.h>
+#include <linux/mfd/samsung/core.h>
+#include <linux/mfd/samsung/s2mu005.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <media/v4l2-flash-led-class.h>
+
+#define MAX_CHANNELS 2
+
+struct s2m_led {
+ struct regmap *regmap;
+ struct led_classdev_flash fled;
+ struct v4l2_flash *v4l2_flash;
+ /*
+ * The mutex object prevents the concurrent access of flash control
+ * registers by the LED and V4L2 subsystems.
+ */
+ struct mutex lock;
+ unsigned int reg_enable;
+ u8 channel;
+ u8 flash_brightness;
+ u8 flash_timeout;
+};
+
+static struct s2m_led *to_s2m_led(struct led_classdev_flash *fled)
+{
+ return container_of(fled, struct s2m_led, fled);
+}
+
+static struct led_classdev_flash *to_s2m_fled(struct led_classdev *cdev)
+{
+ return container_of(cdev, struct led_classdev_flash, led_cdev);
+}
+
+static int s2m_fled_flash_brightness_set(struct led_classdev_flash *fled, u32 brightness)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ struct led_flash_setting *setting = &fled->brightness;
+
+ led->flash_brightness = (brightness - setting->min) / setting->step;
+
+ return 0;
+}
+
+static int s2m_fled_flash_timeout_set(struct led_classdev_flash *fled, u32 timeout)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ struct led_flash_setting *setting = &fled->timeout;
+
+ led->flash_timeout = (timeout - setting->min) / setting->step;
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_V4L2_FLASH_LED_CLASS)
+static int s2m_fled_flash_external_strobe_set(struct v4l2_flash *v4l2_flash, bool enable)
+{
+ struct s2m_led *led = to_led(v4l2_flash->fled_cdev);
+
+ mutex_lock(&led->lock);
+
+ led->fled.ops->strobe_set(&led->fled, enable);
+
+ mutex_unlock(&led->lock);
+
+ return 0;
+}
+
+static const struct v4l2_flash_ops s2m_fled_v4l2_flash_ops = {
+ .external_strobe_set = s2m_fled_flash_external_strobe_set,
+};
+#else
+static const struct v4l2_flash_ops s2m_fled_v4l2_flash_ops;
+#endif
+
+static void s2m_fled_v4l2_flash_release(void *v4l2_flash)
+{
+ v4l2_flash_release(v4l2_flash);
+}
+
+static int s2mu005_fled_torch_brightness_set(struct led_classdev *cdev, enum led_brightness value)
+{
+ struct s2m_led *led = to_s2m_led(to_s2m_fled(cdev));
+ int ret;
+
+ mutex_lock(&led->lock);
+
+ if (!value) {
+ ret = regmap_clear_bits(led->regmap, led->reg_enable,
+ S2MU005_FLED_TORCH_EN(led->channel));
+ if (ret < 0)
+ dev_err(cdev->dev, "failed to disable torch LED\n");
+ goto unlock;
+ }
+
+ ret = regmap_update_bits(led->regmap, S2MU005_REG_FLED_CH_CTRL1(led->channel),
+ S2MU005_FLED_TORCH_IOUT,
+ FIELD_PREP(S2MU005_FLED_TORCH_IOUT, value - 1));
+ if (ret < 0) {
+ dev_err(cdev->dev, "failed to set torch current\n");
+ goto unlock;
+ }
+
+ ret = regmap_set_bits(led->regmap, led->reg_enable, S2MU005_FLED_TORCH_EN(led->channel));
+ if (ret < 0) {
+ dev_err(cdev->dev, "failed to enable torch LED\n");
+ goto unlock;
+ }
+
+unlock:
+ mutex_unlock(&led->lock);
+
+ return ret;
+}
+
+static int s2mu005_fled_flash_strobe_set(struct led_classdev_flash *fled, bool state)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ int ret;
+
+ mutex_lock(&led->lock);
+
+ ret = regmap_clear_bits(led->regmap, led->reg_enable, S2MU005_FLED_FLASH_EN(led->channel));
+ if (ret < 0) {
+ dev_err(fled->led_cdev.dev, "failed to disable flash LED\n");
+ goto unlock;
+ }
+
+ if (!state)
+ goto unlock;
+
+ ret = regmap_update_bits(led->regmap, S2MU005_REG_FLED_CH_CTRL0(led->channel),
+ S2MU005_FLED_FLASH_IOUT,
+ FIELD_PREP(S2MU005_FLED_FLASH_IOUT, led->flash_brightness));
+ if (ret < 0) {
+ dev_err(fled->led_cdev.dev, "failed to set flash brightness\n");
+ goto unlock;
+ }
+
+ ret = regmap_update_bits(led->regmap, S2MU005_REG_FLED_CH_CTRL3(led->channel),
+ S2MU005_FLED_FLASH_TIMEOUT,
+ FIELD_PREP(S2MU005_FLED_FLASH_TIMEOUT, led->flash_timeout));
+ if (ret < 0) {
+ dev_err(fled->led_cdev.dev, "failed to set flash timeout\n");
+ goto unlock;
+ }
+
+ ret = regmap_set_bits(led->regmap, led->reg_enable, S2MU005_FLED_FLASH_EN(led->channel));
+ if (ret < 0) {
+ dev_err(fled->led_cdev.dev, "failed to enable flash LED\n");
+ goto unlock;
+ }
+
+unlock:
+ mutex_unlock(&led->lock);
+
+ return 0;
+}
+
+static int s2mu005_fled_flash_strobe_get(struct led_classdev_flash *fled, bool *state)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ u32 val;
+ int ret;
+
+ mutex_lock(&led->lock);
+
+ ret = regmap_read(led->regmap, S2MU005_REG_FLED_STATUS, &val);
+ if (ret < 0) {
+ dev_err(fled->led_cdev.dev, "failed to fetch LED status");
+ goto unlock;
+ }
+
+ *state = !!(val & S2MU005_FLED_FLASH_STATUS(led->channel));
+
+unlock:
+ mutex_unlock(&led->lock);
+
+ return ret;
+}
+
+static const struct led_flash_ops s2mu005_fled_flash_ops = {
+ .flash_brightness_set = s2m_fled_flash_brightness_set,
+ .timeout_set = s2m_fled_flash_timeout_set,
+ .strobe_set = s2mu005_fled_flash_strobe_set,
+ .strobe_get = s2mu005_fled_flash_strobe_get,
+};
+
+static int s2mu005_fled_init(struct s2m_led *led, struct device *dev, struct regmap *regmap,
+ unsigned int nr_channels)
+{
+ unsigned int val;
+ int i, ret;
+
+ /* Enable the LED channels. */
+ ret = regmap_set_bits(regmap, S2MU005_REG_FLED_CTRL1, S2MU005_FLED_CH_EN);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to enable LED channels\n");
+
+ ret = regmap_read(regmap, S2MU005_REG_ID, &val);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to read revision\n");
+
+ for (i = 0; i < nr_channels; i++) {
+ /*
+ * Read the revision register. Revision EVT0 has the register
+ * at CTRL4, while EVT1 and higher have it at CTRL6.
+ */
+ if (FIELD_GET(S2MU005_ID_MASK, val) == 0)
+ led[i].reg_enable = S2MU005_REG_FLED_CTRL4;
+ else
+ led[i].reg_enable = S2MU005_REG_FLED_CTRL6;
+ }
+
+ return 0;
+}
+
+static int s2mu005_fled_init_channel(struct s2m_led *led, struct device *dev,
+ struct fwnode_handle *fwnp)
+{
+ struct led_classdev *cdev = &led->fled.led_cdev;
+ struct led_init_data init_data = {};
+ struct v4l2_flash_config v4l2_cfg = {};
+ int ret;
+ cdev->max_brightness = 16;
+ cdev->brightness_set_blocking = s2mu005_fled_torch_brightness_set,
+ cdev->flags |= LED_DEV_CAP_FLASH;
+
+ led->fled.timeout.min = 62000;
+ led->fled.timeout.step = 62000;
+ led->fled.timeout.max = 992000;
+ led->fled.timeout.val = 992000;
+
+ led->fled.brightness.min = 25000;
+ led->fled.brightness.step = 25000;
+ led->fled.brightness.max = 375000; /* 400000 causes flickering */
+ led->fled.brightness.val = 375000;
+
+ s2m_fled_flash_timeout_set(&led->fled, led->fled.timeout.val);
+ s2m_fled_flash_brightness_set(&led->fled, led->fled.brightness.val);
+
+ led->fled.ops = &s2mu005_fled_flash_ops;
+
+ init_data.fwnode = fwnp;
+ ret = devm_led_classdev_flash_register_ext(dev, &led->fled, &init_data);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to create LED flash device\n");
+
+ v4l2_cfg.intensity.min = led->fled.timeout.min;
+ v4l2_cfg.intensity.step = led->fled.timeout.step;
+ v4l2_cfg.intensity.max = led->fled.timeout.max;
+ v4l2_cfg.intensity.val = led->fled.timeout.val;
+
+ v4l2_cfg.has_external_strobe = true;
+
+ led->v4l2_flash = v4l2_flash_init(dev, fwnp, &led->fled, &s2m_fled_v4l2_flash_ops,
+ &v4l2_cfg);
+ if (IS_ERR(led->v4l2_flash)) {
+ v4l2_flash_release(led->v4l2_flash);
+ return dev_err_probe(dev, PTR_ERR(led->v4l2_flash),
+ "failed to create V4L2 flash device\n");
+ }
+
+ ret = devm_add_action_or_reset(dev, (void *)s2m_fled_v4l2_flash_release, led->v4l2_flash);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to add cleanup action\n");
+
+ return 0;
+}
+
+static int s2m_fled_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sec_pmic_dev *ddata = dev_get_drvdata(dev->parent);
+ struct s2m_led *led;
+ int ret;
+
+ led = devm_kzalloc(dev, sizeof(*led) * MAX_CHANNELS, GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ switch (platform_get_device_id(pdev)->driver_data) {
+ case S2MU005:
+ ret = s2mu005_fled_init(led, dev, ddata->regmap_pmic, MAX_CHANNELS);
+ if (ret)
+ return ret;
+ break;
+ default:
+ return dev_err_probe(dev, -ENODEV, "device type %d is not supported by driver\n",
+ ddata->device_type);
+ }
+
+ device_for_each_child_node_scoped(dev, child) {
+ u32 reg;
+
+ if (fwnode_property_read_u32(child, "reg", ®))
+ continue;
+
+ if (led[reg].regmap) {
+ dev_warn(dev, "duplicate node for channel %d\n", reg);
+ continue;
+ }
+
+ led[reg].regmap = ddata->regmap_pmic;
+ led[reg].channel = (u8)reg;
+
+ ret = devm_mutex_init(dev, &led[reg].lock);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to create mutex\n");
+
+ switch (platform_get_device_id(pdev)->driver_data) {
+ case S2MU005:
+ ret = s2mu005_fled_init_channel(led + reg, dev, child);
+ if (ret < 0)
+ return ret;
+ break;
+ }
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id s2m_fled_id_table[] = {
+ { "s2mu005-flash", S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, s2m_fled_id_table);
+
+static const struct of_device_id s2m_fled_of_match_table[] = {
+ { .compatible = "samsung,s2mu005-flash", .data = (void *)S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, s2m_fled_of_match_table);
+
+static struct platform_driver s2m_fled_driver = {
+ .driver = {
+ .name = "s2m-flash",
+ },
+ .probe = s2m_fled_probe,
+ .id_table = s2m_fled_id_table,
+};
+module_platform_driver(s2m_fled_driver);
+
+MODULE_DESCRIPTION("Flash/Torch LED Driver For Samsung S2M Series PMICs");
+MODULE_AUTHOR("Kaustabh Chakraborty <kauschluss@disroot.org>");
+MODULE_LICENSE("GPL");
--
2.53.0
next prev parent reply other threads:[~2026-04-14 6:34 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-04-14 6:32 [PATCH v4 00/13] Support for Samsung S2MU005 PMIC and its sub-devices Kaustabh Chakraborty
2026-04-14 6:32 ` [PATCH v4 01/13] dt-bindings: leds: document Samsung S2M series PMIC flash LED device Kaustabh Chakraborty
2026-04-14 6:32 ` [PATCH v4 02/13] dt-bindings: leds: document Samsung S2M series PMIC RGB " Kaustabh Chakraborty
2026-04-15 7:03 ` Krzysztof Kozlowski
2026-04-15 17:30 ` Kaustabh Chakraborty
2026-04-16 8:23 ` Krzysztof Kozlowski
2026-04-16 12:15 ` Kaustabh Chakraborty
2026-04-14 6:32 ` [PATCH v4 03/13] dt-bindings: extcon: document Samsung S2M series PMIC extcon device Kaustabh Chakraborty
2026-04-14 6:32 ` [PATCH v4 04/13] dt-bindings: power: supply: document Samsung S2M series PMIC charger device Kaustabh Chakraborty
2026-04-15 7:18 ` Krzysztof Kozlowski
2026-04-15 14:03 ` Kaustabh Chakraborty
2026-04-15 14:39 ` Krzysztof Kozlowski
2026-04-14 6:32 ` [PATCH v4 05/13] dt-bindings: mfd: s2mps11: add documentation for S2MU005 PMIC Kaustabh Chakraborty
2026-04-14 7:58 ` Rob Herring (Arm)
2026-04-15 7:17 ` Krzysztof Kozlowski
2026-04-15 14:22 ` Kaustabh Chakraborty
2026-04-15 14:27 ` Krzysztof Kozlowski
2026-04-14 6:32 ` [PATCH v4 06/13] mfd: sec: add support " Kaustabh Chakraborty
2026-04-14 6:32 ` [PATCH v4 07/13] mfd: sec: set DMA coherent mask Kaustabh Chakraborty
2026-04-15 7:19 ` Krzysztof Kozlowski
2026-04-14 6:33 ` [PATCH v4 08/13] mfd: sec: resolve PMIC revision in S2MU005 Kaustabh Chakraborty
2026-04-14 7:25 ` Kaustabh Chakraborty
2026-04-14 6:33 ` Kaustabh Chakraborty [this message]
2026-04-14 6:33 ` [PATCH v4 10/13] leds: rgb: add support for Samsung S2M series PMIC RGB LED device Kaustabh Chakraborty
2026-04-14 6:33 ` [PATCH v4 11/13] Documentation: leds: document pattern behavior of Samsung S2M series PMIC RGB LEDs Kaustabh Chakraborty
2026-04-14 6:33 ` [PATCH v4 12/13] extcon: add support for Samsung S2M series PMIC extcon devices Kaustabh Chakraborty
2026-04-14 6:33 ` [PATCH v4 13/13] power: supply: add support for Samsung S2M series PMIC charger device Kaustabh Chakraborty
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260414-s2mu005-pmic-v4-9-7fe7480577e6@disroot.org \
--to=kauschluss@disroot.org \
--cc=alexandre.belloni@bootlin.com \
--cc=andre.draszik@linaro.org \
--cc=conor+dt@kernel.org \
--cc=corbet@lwn.net \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=kernel@lvkasz.us \
--cc=krzk+dt@kernel.org \
--cc=krzk@kernel.org \
--cc=lee@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-rtc@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
--cc=pavel@kernel.org \
--cc=robh@kernel.org \
--cc=skhan@linuxfoundation.org \
--cc=sre@kernel.org \
--cc=trannamatk@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox