* [PATCH v7 04/10] mfd: sec: add support for S2MU005 PMIC
From: Kaustabh Chakraborty @ 2026-05-15 21:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, Yassine Oudjana
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260516-s2mu005-pmic-v7-0-73f9702fb461@disroot.org>
Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
USB Interface Controller), and flash and RGB LED controllers.
S2MU005's interrupt registers divided into three domains, each for the
charger, flash LEDs, and the MUIC, packed into a single regmap IRQ chip
construct.
In devices other than S2MPG1X, the revision can be retrieved from the
first register of the PMIC regmap. In S2MU005 however, the location is
in offset 0x73. Introduce a switch-case block to allow selecting the
REG_ID register. S2MU005 also has a field mask for the revision. Apply
it using FIELD_GET() and get the extracted value.
Add initial support for S2MU005 in the PMIC driver, along with its three
interrupt chips, and support for allowing to fetch revision based on the
device variant.
Co-developed-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/mfd/sec-common.c | 34 +++-
drivers/mfd/sec-i2c.c | 29 ++++
drivers/mfd/sec-irq.c | 73 ++++++++
include/linux/mfd/samsung/core.h | 1 +
include/linux/mfd/samsung/irq.h | 66 +++++++
include/linux/mfd/samsung/s2mu005.h | 332 ++++++++++++++++++++++++++++++++++++
6 files changed, 529 insertions(+), 6 deletions(-)
diff --git a/drivers/mfd/sec-common.c b/drivers/mfd/sec-common.c
index bd8b5f9686892..22f6c74eb6c0e 100644
--- a/drivers/mfd/sec-common.c
+++ b/drivers/mfd/sec-common.c
@@ -16,6 +16,7 @@
#include <linux/mfd/samsung/irq.h>
#include <linux/mfd/samsung/s2mps11.h>
#include <linux/mfd/samsung/s2mps13.h>
+#include <linux/mfd/samsung/s2mu005.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/pm.h>
@@ -105,22 +106,39 @@ static const struct mfd_cell s2mpu05_devs[] = {
MFD_CELL_RES("s2mps15-rtc", s2mpu05_rtc_resources),
};
+static const struct resource s2mu005_muic_resources[] = {
+ DEFINE_RES_IRQ_NAMED(S2MU005_IRQ_MUIC_ATTACH, "attach"),
+ DEFINE_RES_IRQ_NAMED(S2MU005_IRQ_MUIC_DETACH, "detach"),
+};
+
+static const struct mfd_cell s2mu005_devs[] = {
+ MFD_CELL_NAME("s2mu005-charger"),
+ MFD_CELL_OF("s2mu005-flash", NULL, NULL, 0, 0, "samsung,s2mu005-flash"),
+ MFD_CELL_OF("s2mu005-muic", s2mu005_muic_resources, NULL, 0, 0, "samsung,s2mu005-muic"),
+ MFD_CELL_OF("s2mu005-rgb", NULL, NULL, 0, 0, "samsung,s2mu005-rgb"),
+};
+
static void sec_pmic_dump_rev(struct sec_pmic_dev *sec_pmic)
{
- unsigned int val;
+ unsigned int reg, mask, val;
- /* For s2mpg1x, the revision is in a different regmap */
switch (sec_pmic->device_type) {
case S2MPG10:
case S2MPG11:
+ /* For s2mpg1x, the revision is in a different regmap */
return;
- default:
+ case S2MU005:
+ reg = S2MU005_REG_ID;
+ mask = S2MU005_ID_MASK;
break;
+ default:
+ /* For other device types, REG_ID is always the first register. */
+ reg = S2MPS11_REG_ID;
+ mask = ~0;
}
- /* For each device type, the REG_ID is always the first register */
- if (!regmap_read(sec_pmic->regmap_pmic, S2MPS11_REG_ID, &val))
- dev_dbg(sec_pmic->dev, "Revision: 0x%x\n", val);
+ if (!regmap_read(sec_pmic->regmap_pmic, reg, &val))
+ dev_dbg(sec_pmic->dev, "Revision: 0x%x\n", field_get(mask, val));
}
static void sec_pmic_configure(struct sec_pmic_dev *sec_pmic)
@@ -250,6 +268,10 @@ int sec_pmic_probe(struct device *dev, int device_type, unsigned int irq,
sec_devs = s2mpu05_devs;
num_sec_devs = ARRAY_SIZE(s2mpu05_devs);
break;
+ case S2MU005:
+ sec_devs = s2mu005_devs;
+ num_sec_devs = ARRAY_SIZE(s2mu005_devs);
+ break;
default:
return dev_err_probe(sec_pmic->dev, -EINVAL,
"Unsupported device type %d\n",
diff --git a/drivers/mfd/sec-i2c.c b/drivers/mfd/sec-i2c.c
index 3132b849b4bc4..d8609886fcc80 100644
--- a/drivers/mfd/sec-i2c.c
+++ b/drivers/mfd/sec-i2c.c
@@ -17,6 +17,7 @@
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s2mps15.h>
#include <linux/mfd/samsung/s2mpu02.h>
+#include <linux/mfd/samsung/s2mu005.h>
#include <linux/mfd/samsung/s5m8767.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
@@ -66,6 +67,19 @@ static bool s2mpu02_volatile(struct device *dev, unsigned int reg)
}
}
+static bool s2mu005_volatile(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case S2MU005_REG_CHGR_INT1M:
+ case S2MU005_REG_FLED_INT1M:
+ case S2MU005_REG_MUIC_INT1M:
+ case S2MU005_REG_MUIC_INT2M:
+ return false;
+ default:
+ return true;
+ }
+}
+
static const struct regmap_config s2dos05_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -130,6 +144,15 @@ static const struct regmap_config s2mpu05_regmap_config = {
.val_bits = 8,
};
+static const struct regmap_config s2mu005_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = S2MU005_REG_MUIC_LDOADC_H,
+ .volatile_reg = s2mu005_volatile,
+ .cache_type = REGCACHE_FLAT_S,
+};
+
static const struct regmap_config s5m8767_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -203,6 +226,11 @@ static const struct sec_pmic_i2c_platform_data s2mpu05_data = {
.device_type = S2MPU05,
};
+static const struct sec_pmic_i2c_platform_data s2mu005_data = {
+ .regmap_cfg = &s2mu005_regmap_config,
+ .device_type = S2MU005,
+};
+
static const struct sec_pmic_i2c_platform_data s5m8767_data = {
.regmap_cfg = &s5m8767_regmap_config,
.device_type = S5M8767X,
@@ -217,6 +245,7 @@ static const struct of_device_id sec_pmic_i2c_of_match[] = {
{ .compatible = "samsung,s2mps15-pmic", .data = &s2mps15_data, },
{ .compatible = "samsung,s2mpu02-pmic", .data = &s2mpu02_data, },
{ .compatible = "samsung,s2mpu05-pmic", .data = &s2mpu05_data, },
+ { .compatible = "samsung,s2mu005-pmic", .data = &s2mu005_data, },
{ .compatible = "samsung,s5m8767-pmic", .data = &s5m8767_data, },
{ },
};
diff --git a/drivers/mfd/sec-irq.c b/drivers/mfd/sec-irq.c
index 133188391f7c2..42862807be1a0 100644
--- a/drivers/mfd/sec-irq.c
+++ b/drivers/mfd/sec-irq.c
@@ -16,6 +16,7 @@
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s2mpu02.h>
#include <linux/mfd/samsung/s2mpu05.h>
+#include <linux/mfd/samsung/s2mu005.h>
#include <linux/mfd/samsung/s5m8767.h>
#include <linux/regmap.h>
#include "sec-core.h"
@@ -223,6 +224,65 @@ static const struct regmap_irq s2mpu05_irqs[] = {
REGMAP_IRQ_REG(S2MPU05_IRQ_TSD, 2, S2MPU05_IRQ_TSD_MASK),
};
+static const struct regmap_irq s2mu005_irqs[] = {
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_DETBAT, 0, S2MU005_IRQ_CHGR_DETBAT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_BAT, 0, S2MU005_IRQ_CHGR_BAT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_IVR, 0, S2MU005_IRQ_CHGR_IVR_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_EVENT, 0, S2MU005_IRQ_CHGR_EVENT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_CHG, 0, S2MU005_IRQ_CHGR_CHG_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_VMID, 0, S2MU005_IRQ_CHGR_VMID_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_WCIN, 0, S2MU005_IRQ_CHGR_WCIN_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_VBUS, 0, S2MU005_IRQ_CHGR_VBUS_MASK),
+
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_LBPROT, 1, S2MU005_IRQ_FLED_LBPROT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_OPENCH2, 1, S2MU005_IRQ_FLED_OPENCH2_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_OPENCH1, 1, S2MU005_IRQ_FLED_OPENCH1_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_SHORTCH2, 1, S2MU005_IRQ_FLED_SHORTCH2_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_SHORTCH1, 1, S2MU005_IRQ_FLED_SHORTCH1_MASK),
+
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_ATTACH, 2, S2MU005_IRQ_MUIC_ATTACH_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_DETACH, 2, S2MU005_IRQ_MUIC_DETACH_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_KP, 2, S2MU005_IRQ_MUIC_KP_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_LKP, 2, S2MU005_IRQ_MUIC_LKP_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_LKR, 2, S2MU005_IRQ_MUIC_LKR_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_RIDCHG, 2, S2MU005_IRQ_MUIC_RIDCHG_MASK),
+
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_VBUSON, 3, S2MU005_IRQ_MUIC_VBUSON_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_RSVD, 3, S2MU005_IRQ_MUIC_RSVD_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_ADC, 3, S2MU005_IRQ_MUIC_ADC_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_STUCK, 3, S2MU005_IRQ_MUIC_STUCK_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_STUCKRCV, 3, S2MU005_IRQ_MUIC_STUCKRCV_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_MHDL, 3, S2MU005_IRQ_MUIC_MHDL_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_AVCHG, 3, S2MU005_IRQ_MUIC_AVCHG_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_VBUSOFF, 3, S2MU005_IRQ_MUIC_VBUSOFF_MASK),
+};
+
+static unsigned int s2mu005_irq_get_reg(struct regmap_irq_chip_data *data,
+ unsigned int base, int index)
+{
+ const unsigned int irqf_regs[] = {
+ S2MU005_REG_CHGR_INT1,
+ S2MU005_REG_FLED_INT1,
+ S2MU005_REG_MUIC_INT1,
+ S2MU005_REG_MUIC_INT2,
+ };
+ const unsigned int mask_regs[] = {
+ S2MU005_REG_CHGR_INT1M,
+ S2MU005_REG_FLED_INT1M,
+ S2MU005_REG_MUIC_INT1M,
+ S2MU005_REG_MUIC_INT2M,
+ };
+
+ switch (base) {
+ case S2MU005_REG_CHGR_INT1:
+ return irqf_regs[index];
+ case S2MU005_REG_CHGR_INT1M:
+ return mask_regs[index];
+ }
+
+ return base;
+}
+
static const struct regmap_irq s5m8767_irqs[] = {
REGMAP_IRQ_REG(S5M8767_IRQ_PWRR, 0, S5M8767_IRQ_PWRR_MASK),
REGMAP_IRQ_REG(S5M8767_IRQ_PWRF, 0, S5M8767_IRQ_PWRF_MASK),
@@ -337,6 +397,16 @@ static const struct regmap_irq_chip s2mpu05_irq_chip = {
.ack_base = S2MPU05_REG_INT1,
};
+static const struct regmap_irq_chip s2mu005_irq_chip = {
+ .name = "s2mu005",
+ .irqs = s2mu005_irqs,
+ .num_irqs = ARRAY_SIZE(s2mu005_irqs),
+ .num_regs = 4,
+ .status_base = S2MU005_REG_CHGR_INT1,
+ .mask_base = S2MU005_REG_CHGR_INT1M,
+ .get_irq_reg = s2mu005_irq_get_reg,
+};
+
static const struct regmap_irq_chip s5m8767_irq_chip = {
.name = "s5m8767",
.irqs = s5m8767_irqs,
@@ -442,6 +512,9 @@ struct regmap_irq_chip_data *sec_irq_init(struct sec_pmic_dev *sec_pmic)
case S2MPU05:
sec_irq_chip = &s2mpu05_irq_chip;
break;
+ case S2MU005:
+ sec_irq_chip = &s2mu005_irq_chip;
+ break;
default:
return dev_err_ptr_probe(sec_pmic->dev, -EINVAL, "Unsupported device type %d\n",
sec_pmic->device_type);
diff --git a/include/linux/mfd/samsung/core.h b/include/linux/mfd/samsung/core.h
index 4480c631110a6..6191f409de945 100644
--- a/include/linux/mfd/samsung/core.h
+++ b/include/linux/mfd/samsung/core.h
@@ -47,6 +47,7 @@ enum sec_device_type {
S2MPS15X,
S2MPU02,
S2MPU05,
+ S2MU005,
};
/**
diff --git a/include/linux/mfd/samsung/irq.h b/include/linux/mfd/samsung/irq.h
index 6eab95de6fa83..19d0f0e12944f 100644
--- a/include/linux/mfd/samsung/irq.h
+++ b/include/linux/mfd/samsung/irq.h
@@ -408,6 +408,72 @@ enum s2mpu05_irq {
#define S2MPU05_IRQ_INT140C_MASK BIT(1)
#define S2MPU05_IRQ_TSD_MASK BIT(2)
+enum s2mu005_irq {
+ S2MU005_IRQ_CHGR_DETBAT,
+ S2MU005_IRQ_CHGR_BAT,
+ S2MU005_IRQ_CHGR_IVR,
+ S2MU005_IRQ_CHGR_EVENT,
+ S2MU005_IRQ_CHGR_CHG,
+ S2MU005_IRQ_CHGR_VMID,
+ S2MU005_IRQ_CHGR_WCIN,
+ S2MU005_IRQ_CHGR_VBUS,
+
+ S2MU005_IRQ_FLED_LBPROT,
+ S2MU005_IRQ_FLED_OPENCH2,
+ S2MU005_IRQ_FLED_OPENCH1,
+ S2MU005_IRQ_FLED_SHORTCH2,
+ S2MU005_IRQ_FLED_SHORTCH1,
+
+ S2MU005_IRQ_MUIC_ATTACH,
+ S2MU005_IRQ_MUIC_DETACH,
+ S2MU005_IRQ_MUIC_KP,
+ S2MU005_IRQ_MUIC_LKP,
+ S2MU005_IRQ_MUIC_LKR,
+ S2MU005_IRQ_MUIC_RIDCHG,
+
+ S2MU005_IRQ_MUIC_VBUSON,
+ S2MU005_IRQ_MUIC_RSVD,
+ S2MU005_IRQ_MUIC_ADC,
+ S2MU005_IRQ_MUIC_STUCK,
+ S2MU005_IRQ_MUIC_STUCKRCV,
+ S2MU005_IRQ_MUIC_MHDL,
+ S2MU005_IRQ_MUIC_AVCHG,
+ S2MU005_IRQ_MUIC_VBUSOFF,
+
+ S2MU005_IRQ_NR,
+};
+
+#define S2MU005_IRQ_CHGR_DETBAT_MASK BIT(0)
+#define S2MU005_IRQ_CHGR_BAT_MASK BIT(1)
+#define S2MU005_IRQ_CHGR_IVR_MASK BIT(2)
+#define S2MU005_IRQ_CHGR_EVENT_MASK BIT(3)
+#define S2MU005_IRQ_CHGR_CHG_MASK BIT(4)
+#define S2MU005_IRQ_CHGR_VMID_MASK BIT(5)
+#define S2MU005_IRQ_CHGR_WCIN_MASK BIT(6)
+#define S2MU005_IRQ_CHGR_VBUS_MASK BIT(7)
+
+#define S2MU005_IRQ_FLED_LBPROT_MASK BIT(2)
+#define S2MU005_IRQ_FLED_OPENCH2_MASK BIT(4)
+#define S2MU005_IRQ_FLED_OPENCH1_MASK BIT(5)
+#define S2MU005_IRQ_FLED_SHORTCH2_MASK BIT(6)
+#define S2MU005_IRQ_FLED_SHORTCH1_MASK BIT(7)
+
+#define S2MU005_IRQ_MUIC_ATTACH_MASK BIT(0)
+#define S2MU005_IRQ_MUIC_DETACH_MASK BIT(1)
+#define S2MU005_IRQ_MUIC_KP_MASK BIT(2)
+#define S2MU005_IRQ_MUIC_LKP_MASK BIT(3)
+#define S2MU005_IRQ_MUIC_LKR_MASK BIT(4)
+#define S2MU005_IRQ_MUIC_RIDCHG_MASK BIT(5)
+
+#define S2MU005_IRQ_MUIC_VBUSON_MASK BIT(0)
+#define S2MU005_IRQ_MUIC_RSVD_MASK BIT(1)
+#define S2MU005_IRQ_MUIC_ADC_MASK BIT(2)
+#define S2MU005_IRQ_MUIC_STUCK_MASK BIT(3)
+#define S2MU005_IRQ_MUIC_STUCKRCV_MASK BIT(4)
+#define S2MU005_IRQ_MUIC_MHDL_MASK BIT(5)
+#define S2MU005_IRQ_MUIC_AVCHG_MASK BIT(6)
+#define S2MU005_IRQ_MUIC_VBUSOFF_MASK BIT(7)
+
enum s5m8767_irq {
S5M8767_IRQ_PWRR,
S5M8767_IRQ_PWRF,
diff --git a/include/linux/mfd/samsung/s2mu005.h b/include/linux/mfd/samsung/s2mu005.h
new file mode 100644
index 0000000000000..46e7759545af2
--- /dev/null
+++ b/include/linux/mfd/samsung/s2mu005.h
@@ -0,0 +1,332 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (c) 2026 Kaustabh Chakraborty <kauschluss@disroot.org>
+ * Copyright (c) 2026 Łukasz Lebiedziński <kernel@lvkasz.us>
+ */
+
+#ifndef __LINUX_MFD_S2MU005_H
+#define __LINUX_MFD_S2MU005_H
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+
+/* S2MU005 registers */
+enum s2mu005_reg {
+ S2MU005_REG_CHGR_INT1,
+ S2MU005_REG_CHGR_INT1M,
+
+ S2MU005_REG_FLED_INT1,
+ S2MU005_REG_FLED_INT1M,
+
+ S2MU005_REG_MUIC_INT1,
+ S2MU005_REG_MUIC_INT2,
+ S2MU005_REG_MUIC_INT1M,
+ S2MU005_REG_MUIC_INT2M,
+
+ S2MU005_REG_CHGR_STATUS0,
+ S2MU005_REG_CHGR_STATUS1,
+ S2MU005_REG_CHGR_STATUS2,
+ S2MU005_REG_CHGR_STATUS3,
+ S2MU005_REG_CHGR_STATUS4,
+ S2MU005_REG_CHGR_STATUS5,
+ S2MU005_REG_CHGR_CTRL0,
+ S2MU005_REG_CHGR_CTRL1,
+ S2MU005_REG_CHGR_CTRL2,
+ S2MU005_REG_CHGR_CTRL3,
+ S2MU005_REG_CHGR_CTRL4,
+ S2MU005_REG_CHGR_CTRL5,
+ S2MU005_REG_CHGR_CTRL6,
+ S2MU005_REG_CHGR_CTRL7,
+ S2MU005_REG_CHGR_CTRL8,
+ S2MU005_REG_CHGR_CTRL9,
+ S2MU005_REG_CHGR_CTRL10,
+ S2MU005_REG_CHGR_CTRL11,
+ S2MU005_REG_CHGR_CTRL12,
+ S2MU005_REG_CHGR_CTRL13,
+ S2MU005_REG_CHGR_CTRL14,
+ S2MU005_REG_CHGR_CTRL15,
+ S2MU005_REG_CHGR_CTRL16,
+ S2MU005_REG_CHGR_CTRL17,
+ S2MU005_REG_CHGR_CTRL18,
+ S2MU005_REG_CHGR_CTRL19,
+ S2MU005_REG_CHGR_TEST0,
+ S2MU005_REG_CHGR_TEST1,
+ S2MU005_REG_CHGR_TEST2,
+ S2MU005_REG_CHGR_TEST3,
+ S2MU005_REG_CHGR_TEST4,
+ S2MU005_REG_CHGR_TEST5,
+ S2MU005_REG_CHGR_TEST6,
+ S2MU005_REG_CHGR_TEST7,
+ S2MU005_REG_CHGR_TEST8,
+ S2MU005_REG_CHGR_TEST9,
+ S2MU005_REG_CHGR_TEST10,
+
+ S2MU005_REG_FLED_STATUS,
+ S2MU005_REG_FLED_CH0_CTRL0,
+ S2MU005_REG_FLED_CH0_CTRL1,
+ S2MU005_REG_FLED_CH0_CTRL2,
+ S2MU005_REG_FLED_CH0_CTRL3,
+ S2MU005_REG_FLED_CH1_CTRL0,
+ S2MU005_REG_FLED_CH1_CTRL1,
+ S2MU005_REG_FLED_CH1_CTRL2,
+ S2MU005_REG_FLED_CH1_CTRL3,
+ S2MU005_REG_FLED_CTRL0,
+ S2MU005_REG_FLED_CTRL1,
+ S2MU005_REG_FLED_CTRL2,
+ S2MU005_REG_FLED_CTRL3,
+ S2MU005_REG_FLED_CTRL4,
+ S2MU005_REG_FLED_CTRL5,
+ S2MU005_REG_FLED_CTRL6,
+
+ S2MU005_REG_RGB_EN,
+ S2MU005_REG_RGB_CH0_CTRL,
+ S2MU005_REG_RGB_CH1_CTRL,
+ S2MU005_REG_RGB_CH2_CTRL,
+ S2MU005_REG_RGB_CH0_RAMP,
+ S2MU005_REG_RGB_CH0_STAY,
+ S2MU005_REG_RGB_CH1_RAMP,
+ S2MU005_REG_RGB_CH1_STAY,
+ S2MU005_REG_RGB_CH2_RAMP,
+ S2MU005_REG_RGB_CH2_STAY,
+ S2MU005_REG_RGB_TEST0,
+ S2MU005_REG_RGB_CTRL0,
+
+ S2MU005_REG_MUIC_ADC,
+ S2MU005_REG_MUIC_DEV1,
+ S2MU005_REG_MUIC_DEV2,
+ S2MU005_REG_MUIC_DEV3,
+ S2MU005_REG_MUIC_BUTTON1,
+ S2MU005_REG_MUIC_BUTTON2,
+ S2MU005_REG_MUIC_RESET,
+ S2MU005_REG_MUIC_CHGTYPE,
+ S2MU005_REG_MUIC_DEVAPPLE,
+ S2MU005_REG_MUIC_BCDRESCAN,
+ S2MU005_REG_MUIC_TEST1,
+ S2MU005_REG_MUIC_TEST2,
+ S2MU005_REG_MUIC_TEST3,
+
+ S2MU005_REG_ID = 0x73,
+
+ S2MU005_REG_MUIC_CTRL1 = 0xb2,
+ S2MU005_REG_MUIC_TIMERSET1,
+ S2MU005_REG_MUIC_TIMERSET2,
+ S2MU005_REG_MUIC_SWCTRL,
+ S2MU005_REG_MUIC_TIMERSET3,
+ S2MU005_REG_MUIC_CTRL2,
+ S2MU005_REG_MUIC_CTRL3,
+
+ S2MU005_REG_MUIC_LDOADC_L = 0xbf,
+ S2MU005_REG_MUIC_LDOADC_H,
+};
+
+#define S2MU005_REG_FLED_CH_CTRL0(x) (S2MU005_REG_FLED_CH0_CTRL0 + 4 * (x))
+#define S2MU005_REG_FLED_CH_CTRL1(x) (S2MU005_REG_FLED_CH0_CTRL1 + 4 * (x))
+#define S2MU005_REG_FLED_CH_CTRL2(x) (S2MU005_REG_FLED_CH0_CTRL2 + 4 * (x))
+#define S2MU005_REG_FLED_CH_CTRL3(x) (S2MU005_REG_FLED_CH0_CTRL3 + 4 * (x))
+
+#define S2MU005_REG_RGB_CH_CTRL(x) (S2MU005_REG_RGB_CH0_CTRL + 1 * (x))
+#define S2MU005_REG_RGB_CH_RAMP(x) (S2MU005_REG_RGB_CH0_RAMP + 2 * (x))
+#define S2MU005_REG_RGB_CH_STAY(x) (S2MU005_REG_RGB_CH0_STAY + 2 * (x))
+
+/* S2MU005_REG_CHGR_STATUS0 */
+#define S2MU005_CHGR_VBUS BIT(7)
+#define S2MU005_CHGR_WCIN BIT(6)
+#define S2MU005_CHGR_VMID BIT(5)
+#define S2MU005_CHGR_CHG BIT(4)
+#define S2MU005_CHGR_STAT GENMASK(3, 0)
+
+#define S2MU005_CHGR_STAT_DONE 8
+#define S2MU005_CHGR_STAT_TOPOFF 7
+#define S2MU005_CHGR_STAT_DONE_FLAG 6
+#define S2MU005_CHGR_STAT_CV 5
+#define S2MU005_CHGR_STAT_CC 4
+#define S2MU005_CHGR_STAT_COOL_CHG 3
+#define S2MU005_CHGR_STAT_PRE_CHG 2
+
+/* S2MU005_REG_CHGR_STATUS1 */
+#define S2MU005_CHGR_DETBAT BIT(7)
+#define S2MU005_CHGR_VBUS_OVP GENMASK(6, 4)
+
+#define S2MU005_CHGR_VBUS_OVP_OVERVOLT 2
+
+/* S2MU005_REG_CHGR_STATUS2 */
+#define S2MU005_CHGR_BAT GENMASK(6, 4)
+
+#define S2MU005_CHGR_BAT_VOLT_DET 7
+#define S2MU005_CHGR_BAT_FAST_CHG_DET 6
+#define S2MU005_CHGR_BAT_COOL_CHG_DET 5
+#define S2MU005_CHGR_BAT_LOW_CHG 2
+#define S2MU005_CHGR_BAT_SELF_DISCHG 1
+#define S2MU005_CHGR_BAT_OVP_DET 0
+
+/* S2MU005_REG_CHGR_STATUS3 */
+#define S2MU005_CHGR_EVT GENMASK(3, 0)
+
+#define S2MU005_CHGR_EVT_WDT_RST 6
+#define S2MU005_CHGR_EVT_WDT_SUSP 5
+#define S2MU005_CHGR_EVT_VSYS_VUVLO 4
+#define S2MU005_CHGR_EVT_VSYS_VOVP 3
+#define S2MU005_CHGR_EVT_THERM_FOLDBACK 2
+#define S2MU005_CHGR_EVT_THERM_SHUTDOWN 1
+
+/* S2MU005_REG_CHGR_CTRL0 */
+#define S2MU005_CHGR_CHG_EN BIT(4)
+#define S2MU005_CHGR_OP_MODE GENMASK(2, 0)
+
+#define S2MU005_CHGR_OP_MODE_OTG BIT(2)
+#define S2MU005_CHGR_OP_MODE_CHG BIT(1)
+
+/* S2MU005_REG_CHGR_CTRL1 */
+#define S2MU005_CHGR_VIN_DROP GENMASK(6, 4)
+
+/* S2MU005_REG_CHGR_CTRL2 */
+#define S2MU005_CHGR_IN_CURR_LIM GENMASK(5, 0)
+
+/* S2MU005_REG_CHGR_CTRL4 */
+#define S2MU005_CHGR_OTG_OCP_ON BIT(5)
+#define S2MU005_CHGR_OTG_OCP_OFF BIT(4)
+#define S2MU005_CHGR_OTG_OCP GENMASK(3, 2)
+#define S2MU005_CHGR_OTG_OCP_1P5A 0x3
+
+/* S2MU005_REG_CHGR_CTRL5 */
+#define S2MU005_CHGR_VMID_BOOST GENMASK(4, 0)
+#define S2MU005_CHGR_VMID_BOOST_5P1V 0x16
+
+/* S2MU005_REG_CHGR_CTRL6 */
+#define S2MU005_CHGR_COOL_CHG_CURR GENMASK(5, 0)
+
+/* S2MU005_REG_CHGR_CTRL7 */
+#define S2MU005_CHGR_FAST_CHG_CURR GENMASK(5, 0)
+
+/* S2MU005_REG_CHGR_CTRL8 */
+#define S2MU005_CHGR_VF_VBAT GENMASK(6, 1)
+
+/* S2MU005_REG_CHGR_CTRL10 */
+#define S2MU005_CHGR_TOPOFF_CURR(x) (GENMASK(3, 0) << 4 * (x))
+
+/* S2MU005_REG_CHGR_CTRL11 */
+#define S2MU005_CHGR_OSC_BOOST GENMASK(6, 5)
+#define S2MU005_CHGR_OSC_BUCK GENMASK(4, 3)
+#define S2MU005_CHGR_OSC_BOOST_2MHZ 0x3
+
+/* S2MU005_REG_CHGR_CTRL12 */
+#define S2MU005_CHGR_WDT GENMASK(2, 0)
+
+#define S2MU005_CHGR_WDT_ON BIT(2)
+#define S2MU005_CHGR_WDT_OFF BIT(1)
+
+/* S2MU005_REG_CHGR_CTRL15 */
+#define S2MU005_CHGR_OTG_EN GENMASK(3, 2)
+#define S2MU005_CHGR_OTG_EN_ON 0x3
+
+/* S2MU005_REG_FLED_STATUS */
+#define S2MU005_FLED_FLASH_STATUS(x) (BIT(7) >> 2 * (x))
+#define S2MU005_FLED_TORCH_STATUS(x) (BIT(6) >> 2 * (x))
+
+/* S2MU005_REG_FLED_CHx_CTRL0 */
+#define S2MU005_FLED_FLASH_IOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CHx_CTRL1 */
+#define S2MU005_FLED_TORCH_IOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CHx_CTRL2 */
+#define S2MU005_FLED_TORCH_TIMEOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CHx_CTRL3 */
+#define S2MU005_FLED_FLASH_TIMEOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CTRL1 */
+#define S2MU005_FLED_CH_EN BIT(7)
+
+/*
+ * S2MU005_REG_FLED_CTRL4 - Rev. EVT0
+ * S2MU005_REG_FLED_CTRL6 - Rev. EVT1 and later
+ */
+#define S2MU005_FLED_FLASH_EN(x) (GENMASK(7, 6) >> 4 * (x))
+#define S2MU005_FLED_TORCH_EN(x) (GENMASK(5, 4) >> 4 * (x))
+
+/* S2MU005_REG_RGB_EN */
+#define S2MU005_RGB_RESET BIT(6)
+#define S2MU005_RGB_SLOPE GENMASK(5, 0)
+
+#define S2MU005_RGB_SLOPE_CONST (BIT(4) | BIT(2) | BIT(0))
+#define S2MU005_RGB_SLOPE_SMOOTH (BIT(5) | BIT(3) | BIT(1))
+
+/* S2MU005_REG_RGB_CHx_RAMP */
+#define S2MU005_RGB_CH_RAMP_UP GENMASK(7, 4)
+#define S2MU005_RGB_CH_RAMP_DN GENMASK(3, 0)
+
+/* S2MU005_REG_RGB_CHx_STAY */
+#define S2MU005_RGB_CH_STAY_HI GENMASK(7, 4)
+#define S2MU005_RGB_CH_STAY_LO GENMASK(3, 0)
+
+/* S2MU005_REG_MUIC_DEV1 */
+#define S2MU005_MUIC_OTG BIT(7)
+#define S2MU005_MUIC_DCP BIT(6)
+#define S2MU005_MUIC_CDP BIT(5)
+#define S2MU005_MUIC_T1_T2_CHG BIT(4)
+#define S2MU005_MUIC_UART BIT(3)
+#define S2MU005_MUIC_SDP BIT(2)
+#define S2MU005_MUIC_LANHUB BIT(1)
+#define S2MU005_MUIC_AUDIO BIT(0)
+
+/* S2MU005_REG_MUIC_DEV2 */
+#define S2MU005_MUIC_SDP_1P8S BIT(7)
+#define S2MU005_MUIC_AV BIT(6)
+#define S2MU005_MUIC_TTY BIT(5)
+#define S2MU005_MUIC_PPD BIT(4)
+#define S2MU005_MUIC_JIG_UART_OFF BIT(3)
+#define S2MU005_MUIC_JIG_UART_ON BIT(2)
+#define S2MU005_MUIC_JIG_USB_OFF BIT(1)
+#define S2MU005_MUIC_JIG_USB_ON BIT(0)
+
+/* S2MU005_REG_MUIC_DEV3 */
+#define S2MU005_MUIC_U200_CHG BIT(7)
+#define S2MU005_MUIC_VBUS_AV BIT(4)
+#define S2MU005_MUIC_VBUS_R255 BIT(1)
+#define S2MU005_MUIC_MHL BIT(0)
+
+/* S2MU005_REG_MUIC_DEVAPPLE */
+#define S2MU005_MUIC_APPLE_CHG_0P5A BIT(7)
+#define S2MU005_MUIC_APPLE_CHG_1P0A BIT(6)
+#define S2MU005_MUIC_APPLE_CHG_2P0A BIT(5)
+#define S2MU005_MUIC_APPLE_CHG_2P4A BIT(4)
+#define S2MU005_MUIC_SDP_DCD_OUT BIT(3)
+#define S2MU005_MUIC_RID_WAKEUP BIT(2)
+#define S2MU005_MUIC_VBUS_WAKEUP BIT(1)
+#define S2MU005_MUIC_BCV1P2_OR_OPEN BIT(0)
+
+/* S2MU005_REG_ID */
+#define S2MU005_ID_MASK GENMASK(3, 0)
+
+/* S2MU005_REG_MUIC_SWCTRL */
+#define S2MU005_MUIC_DM_DP GENMASK(7, 2)
+#define S2MU005_MUIC_JIG BIT(0)
+
+#define S2MU005_MUIC_DM_DP_UART 0x12
+#define S2MU005_MUIC_DM_DP_USB 0x09
+
+/* S2MU005_REG_MUIC_CTRL1 */
+#define S2MU005_MUIC_OPEN BIT(4)
+#define S2MU005_MUIC_RAW_DATA BIT(3)
+#define S2MU005_MUIC_MAN_SW BIT(2)
+#define S2MU005_MUIC_WAIT BIT(1)
+#define S2MU005_MUIC_IRQ BIT(0)
+
+/* S2MU005_REG_MUIC_CTRL3 */
+#define S2MU005_MUIC_ONESHOT_ADC BIT(2)
+
+/* S2MU005_REG_MUIC_LDOADC_L and S2MU005_REG_MUIC_LDOADC_H */
+#define S2MU005_MUIC_VSET GENMASK(4, 0)
+
+#define S2MU005_MUIC_VSET_3P0V 0x1f
+#define S2MU005_MUIC_VSET_2P6V 0x0e
+#define S2MU005_MUIC_VSET_2P4V 0x0c
+#define S2MU005_MUIC_VSET_2P2V 0x0a
+#define S2MU005_MUIC_VSET_2P0V 0x08
+#define S2MU005_MUIC_VSET_1P5V 0x03
+#define S2MU005_MUIC_VSET_1P4V 0x02
+#define S2MU005_MUIC_VSET_1P2V 0x00
+
+#endif /* __LINUX_MFD_S2MU005_H */
--
2.53.0
^ permalink raw reply related
* [PATCH v7 03/10] dt-bindings: mfd: add documentation for S2MU005 PMIC
From: Kaustabh Chakraborty @ 2026-05-15 21:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, Yassine Oudjana
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty, Krzysztof Kozlowski
In-Reply-To: <20260516-s2mu005-pmic-v7-0-73f9702fb461@disroot.org>
Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
USB Interface Controller), and flash and RGB LED controllers.
Add the compatible and documentation for the S2MU005 PMIC. Also, add an
example for nodes for supported sub-devices, i.e. MUIC, flash LEDs, and
RGB LEDs. Charger sub-device uses the node of the parent.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../bindings/mfd/samsung,s2mu005-pmic.yaml | 120 +++++++++++++++++++++
1 file changed, 120 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
new file mode 100644
index 0000000000000..aff68c035b38e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
@@ -0,0 +1,120 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/samsung,s2mu005-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S2MU005 Power Management IC
+
+maintainers:
+ - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+ The S2MU005 is a companion power management IC which includes subdevices for
+ a charger controller, an MUIC (Micro USB Interface Controller), and flash and
+ RGB LED controllers.
+
+allOf:
+ - $ref: /schemas/power/supply/power-supply.yaml#
+
+properties:
+ compatible:
+ const: samsung,s2mu005-pmic
+
+ flash:
+ $ref: /schemas/leds/samsung,s2mu005-flash.yaml#
+ description:
+ Child node describing flash LEDs.
+
+ interrupts:
+ maxItems: 1
+
+ muic:
+ $ref: /schemas/extcon/samsung,s2mu005-muic.yaml#
+ description:
+ Child node describing MUIC device.
+
+ multi-led:
+ type: object
+
+ allOf:
+ - $ref: /schemas/leds/leds-class-multicolor.yaml#
+
+ properties:
+ compatible:
+ const: samsung,s2mu005-rgb
+
+ required:
+ - compatible
+
+ unevaluatedProperties: false
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/leds/common.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@3d {
+ compatible = "samsung,s2mu005-pmic";
+ reg = <0x3d>;
+ interrupt-parent = <&gpa2>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ monitored-battery = <&battery>;
+
+ flash {
+ compatible = "samsung,s2mu005-flash";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ function-enumerator = <1>;
+ };
+ };
+
+ muic {
+ compatible = "samsung,s2mu005-muic";
+
+ connector {
+ compatible = "usb-b-connector";
+ label = "micro-USB";
+ type = "micro";
+ };
+
+ port {
+ muic_to_usb: endpoint {
+ remote-endpoint = <&usb_to_muic>;
+ };
+ };
+ };
+
+ multi-led {
+ compatible = "samsung,s2mu005-rgb";
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_INDICATOR;
+ linux,default-trigger = "pattern";
+ };
+ };
+ };
--
2.53.0
^ permalink raw reply related
* [PATCH v7 02/10] dt-bindings: extcon: document Samsung S2M series PMIC extcon device
From: Kaustabh Chakraborty @ 2026-05-15 21:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, Yassine Oudjana
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty, Conor Dooley,
Krzysztof Kozlowski
In-Reply-To: <20260516-s2mu005-pmic-v7-0-73f9702fb461@disroot.org>
Certain Samsung S2M series PMICs have a MUIC device which reports
various cable states by measuring the ID-GND resistance with an internal
ADC. Document the devicetree schema for this device.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../bindings/extcon/samsung,s2mu005-muic.yaml | 40 ++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml b/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml
new file mode 100644
index 0000000000000..0a320d5e2a352
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/samsung,s2mu005-muic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MUIC Device for Samsung S2M series PMICs
+
+maintainers:
+ - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+ The Samsung S2M series PMIC MUIC device is a USB port accessory
+ detector. It reports multiple states depending on the ID-GND
+ resistance measured by an internal ADC.
+
+ This is a part of device tree bindings for S2M and S5M family of Power
+ Management IC (PMIC).
+
+ See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for
+ additional information and example.
+
+properties:
+ compatible:
+ enum:
+ - samsung,s2mu005-muic
+
+ connector:
+ $ref: /schemas/connector/usb-connector.yaml#
+
+ port:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Port connecting to the USB controller or PHY.
+
+required:
+ - compatible
+ - connector
+ - port
+
+additionalProperties: false
--
2.53.0
^ permalink raw reply related
* [PATCH v7 01/10] dt-bindings: leds: document Samsung S2M series PMIC flash LED device
From: Kaustabh Chakraborty @ 2026-05-15 21:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, Yassine Oudjana
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty, Conor Dooley
In-Reply-To: <20260516-s2mu005-pmic-v7-0-73f9702fb461@disroot.org>
Certain Samsung S2M series PMICs have a flash LED controller with
two LED channels, and with torch and flash control modes. Document the
devicetree schema for the device.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../bindings/leds/samsung,s2mu005-flash.yaml | 52 ++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/Documentation/devicetree/bindings/leds/samsung,s2mu005-flash.yaml b/Documentation/devicetree/bindings/leds/samsung,s2mu005-flash.yaml
new file mode 100644
index 0000000000000..36051ab20509f
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/samsung,s2mu005-flash.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/samsung,s2mu005-flash.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Flash and Torch LED Controller for Samsung S2M series PMICs
+
+maintainers:
+ - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+ The Samsung S2M series PMIC flash LED has two led channels (typically
+ as back and front camera flashes), with support for both torch and
+ flash modes.
+
+ This is a part of device tree bindings for S2M and S5M family of Power
+ Management IC (PMIC).
+
+ See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for
+ additional information and example.
+
+properties:
+ compatible:
+ enum:
+ - samsung,s2mu005-flash
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+patternProperties:
+ "^led@[0-1]$":
+ type: object
+ $ref: common.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ enum: [0, 1]
+
+ required:
+ - reg
+
+required:
+ - compatible
+ - "#address-cells"
+ - "#size-cells"
+
+additionalProperties: false
--
2.53.0
^ permalink raw reply related
* [PATCH v7 00/10] Support for Samsung S2MU005 PMIC and its sub-devices
From: Kaustabh Chakraborty @ 2026-05-15 21:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, Yassine Oudjana
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty, Conor Dooley,
Krzysztof Kozlowski
S2MU005 is an MFD chip manufactured by Samsung Electronics. This is
found in various devices manufactured by Samsung and others, including
all Exynos 7870 devices. It is known to have the following features:
1. Two LED channels with adjustable brightness for use as a torch, or a
flash strobe.
2. An RGB LED with 8-bit channels. Usually programmed as a notification
indicator.
3. An MUIC, which works with USB micro-B (and USB-C?). For the micro-B
variant though, it measures the ID-GND resistance using an internal
ADC.
4. A charger device, which reports if charger is online, voltage,
resistance, etc.
This patch series implements a lot of these features. Naturally, this
series touches upon a lot of subsystems. The 'parent' is the MFD driver,
so the subsystems have some form of dependency to the MFD driver, so
they are not separable.
Here are the subsystems corresponding to the patch numbers:
dt-bindings - 01, 02, 03
mfd - 03, 04, 05
led - 01, 06, 07, 08
extcon - 02, 09
power - 10
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
Changes in v7:
- Add missing tags collected from v5
- Add trailing `#` in s2mu005 mfd dt-schema (Sashiko AI)
- Squash [v6 04/11] with [v6 06/11] to prevent bisect regression (Sashiko AI)
- Remove ack_base from regmap IRQ as not needed by hardware (Sashiko AI)
- Update commit message of [v6 04/11] (Sashiko AI)
- Fix reference to leds-trigger-pattern in [v6 09/11] commit (Sashiko AI)
- Remove Kconfig `select REGMAP_IRQ` from [v6 07/11], [v6 08/11] (Sashiko AI)
- Implement lock for s2m_fled_flash_{brightness,timeout}_set() (Sashiko AI)
- Remove superfluous lock from s2m_fled_flash_external_strobe_set() (Sashiko AI)
- Remove incorrect (void *) cast to s2m_fled_v4l2_flash_release() (Sashiko AI)
- Change regmap_{s/update_bits/write} for slope setting in
s2mu005_rgb_apply_params() (Sashiko AI)
- Allow for extrapolation in s2m_rgb_lut_get_closest_duration() (Sashiko AI)
- Explicitly initialize ramp_{up,dn}_en in s2m_rgb_pattern_set() (Sashiko AI)
- Use duplicated s2mu005_rgb_subled_info for allowing multi-driver (Sashiko AI)
- Change s/CDP/DCP in s2mu005_muic_attach() (Sashiko AI)
- Remove EXTCON_USB state from USB DCP (Sashiko AI)
- Move muic_attach call to irq init, preventing undefined extcon (Sashiko AI)
- Properly propagate errors in platform_get_irq_byname_optional() in extcon-s2m
(Sashiko AI)
- Use duplicated s2mu005_muic_irq_data for allowing multi-driver (Sashiko AI)
- Fix if-else-if chain in s2mu005_chgr_get_usb_type() (Sashiko AI)
- Consider errors in extcon_get_state() call (Sashiko AI)
- Handle NULL possibility on extcon child node in charger (Sashiko AI)
- Link to v6: https://patch.msgid.link/20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org
Changes in v6:
- Fix build, UAF, and functional errors with
CONFIG_V4L2_FLASH_LED_CLASS=m (Lee Jones)
- Remove (ret < 0) wherever redundant (Lee Jones)
- Remove extra conditionals for supporting multiple variants (Lee Jones)
- Fix OOB condition in initailizing flash LED channels (Lee Jones)
- Declare i inside for, like: for (int i = 0; ...) (Lee Jones)
- Rewrite and simplify closest timing function for clarity (Lee Jones)
- Link to v5: https://lore.kernel.org/r/20260424-s2mu005-pmic-v5-0-fcbc9da5a004@disroot.org
Changes in v5:
- Drop port property from charger dt binding (Krzysztof Kozlowski)
- Create separate dt binding for S2MU005 MFD (Krzysztof Kozlowski)
- Move RGB LED and charger schema to parent schema (Rob Herring)
- Fix error of using invalid revision mask
- Link to v4: https://lore.kernel.org/r/20260414-s2mu005-pmic-v4-0-7fe7480577e6@disroot.org
Changes in v4:
- Use OF graph to connect charger with MUIC in device tree
- Move DMA coherent mask to all MFD PMICs (André Draszik)
- Modify pointer names for flash/RGB drivers (Lee Jones)
- Use 100-char line wrap for flash/RGB drivers (Lee Jones)
- Revamp LED device initialization in flash driver (Lee Jones)
- Add proper USB 2.0 support in charger driver (Łukasz Lebiedziński)
- Link to v3: https://lore.kernel.org/r/20260225-s2mu005-pmic-v3-0-b4afee947603@disroot.org
Changes in v3:
- Remove "extcon" text from dt-bindings documentation (Rob Herring)
- Add connector for MUIC node
- Fix dt binding errors reported by robh's bot
- Fix kernel test robot const errors
- Remove FIELD_PREP() values in register header file (André Draszik)
- Add max_register, volatile_reg, cache_type (André Draszik)
- Redo [v2 07/12] to NOT store the PMIC revision (André Draszik)
- Add a commit to fix DMA coherent mask in I2C PMICs
- Implement various flow changes in flash LED driver (André Draszik)
- Use device_for_each_child_node_scoped() (André Draszik)
- Fix CFI panic in devm_add_action_or_reset()
- Link to v2: https://lore.kernel.org/r/20260126-s2mu005-pmic-v2-0-78f1a75f547a@disroot.org
Changes in v2:
- Drop [v1 06/13], instead use regmap_irq_chip::get_irq_regs()
- Remove references to driver in devicetree commits (Conor Dooley)
- Propagate errors of sec_pmic_store_rev() (André Draszik)
- Fix documentation language errors (Randy Dunlap)
- Link to v1: https://lore.kernel.org/r/20251114-s2mu005-pmic-v1-0-9e3184d3a0c9@disroot.org
To: Lee Jones <lee@kernel.org>
To: Pavel Machek <pavel@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Kaustabh Chakraborty <kauschluss@disroot.org>
To: MyungJoo Ham <myungjoo.ham@samsung.com>
To: Chanwoo Choi <cw00.choi@samsung.com>
To: Krzysztof Kozlowski <krzk@kernel.org>
To: André Draszik <andre.draszik@linaro.org>
To: Nam Tran <trannamatk@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Shuah Khan <skhan@linuxfoundation.org>
To: Sebastian Reichel <sre@kernel.org>
Cc: linux-leds@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
---
Kaustabh Chakraborty (10):
dt-bindings: leds: document Samsung S2M series PMIC flash LED device
dt-bindings: extcon: document Samsung S2M series PMIC extcon device
dt-bindings: mfd: add documentation for S2MU005 PMIC
mfd: sec: add support for S2MU005 PMIC
mfd: sec: set DMA coherent mask
leds: flash: add support for Samsung S2M series PMIC flash LED device
leds: rgb: add support for Samsung S2M series PMIC RGB LED device
Documentation: leds: document pattern behavior of Samsung S2M series PMIC RGB LEDs
extcon: add support for Samsung S2M series PMIC extcon devices
power: supply: add support for Samsung S2M series PMIC charger device
.../bindings/extcon/samsung,s2mu005-muic.yaml | 40 ++
.../bindings/leds/samsung,s2mu005-flash.yaml | 52 +++
.../bindings/mfd/samsung,s2mu005-pmic.yaml | 120 ++++++
Documentation/leds/index.rst | 1 +
Documentation/leds/leds-s2m-rgb.rst | 60 +++
drivers/extcon/Kconfig | 9 +
drivers/extcon/Makefile | 1 +
drivers/extcon/extcon-s2m.c | 370 ++++++++++++++++++
drivers/leds/flash/Kconfig | 11 +
drivers/leds/flash/Makefile | 1 +
drivers/leds/flash/leds-s2m-flash.c | 350 +++++++++++++++++
drivers/leds/rgb/Kconfig | 10 +
drivers/leds/rgb/Makefile | 1 +
drivers/leds/rgb/leds-s2m-rgb.c | 426 +++++++++++++++++++++
drivers/mfd/sec-common.c | 37 +-
drivers/mfd/sec-i2c.c | 29 ++
drivers/mfd/sec-irq.c | 73 ++++
drivers/power/supply/Kconfig | 10 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/s2m-charger.c | 313 +++++++++++++++
include/linux/mfd/samsung/core.h | 1 +
include/linux/mfd/samsung/irq.h | 66 ++++
include/linux/mfd/samsung/s2mu005.h | 332 ++++++++++++++++
23 files changed, 2308 insertions(+), 6 deletions(-)
---
base-commit: e98d21c170b01ddef366f023bbfcf6b31509fa83
change-id: 20251112-s2mu005-pmic-0c67fa6bac3c
Best regards,
--
Kaustabh Chakraborty <kauschluss@disroot.org>
^ permalink raw reply
* Re: [PATCH v6 03/11] dt-bindings: mfd: add documentation for S2MU005 PMIC
From: Kaustabh Chakraborty @ 2026-05-15 21:11 UTC (permalink / raw)
To: Conor Dooley, Kaustabh Chakraborty
Cc: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, linux-leds, devicetree,
linux-kernel, linux-pm, linux-samsung-soc, linux-rtc, linux-doc
In-Reply-To: <20260515-justly-recite-6028f4bfb24a@spud>
On 2026-05-15 18:14 +01:00, Conor Dooley wrote:
> On Fri, May 15, 2026 at 04:08:59PM +0530, Kaustabh Chakraborty wrote:
>> Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
>> USB Interface Controller), and flash and RGB LED controllers.
>>
>> Add the compatible and documentation for the S2MU005 PMIC. Also, add an
>> example for nodes for supported sub-devices, i.e. MUIC, flash LEDs, and
>> RGB LEDs. Charger sub-device uses the node of the parent.
>>
>> Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
>> ---
>> .../bindings/mfd/samsung,s2mu005-pmic.yaml | 120 +++++++++++++++++++++
>> 1 file changed, 120 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
>> new file mode 100644
>> index 0000000000000..0e6afb7d2017b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
>> @@ -0,0 +1,120 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/mfd/samsung,s2mu005-pmic.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Samsung S2MU005 Power Management IC
>> +
>> +maintainers:
>> + - Kaustabh Chakraborty <kauschluss@disroot.org>
>> +
>> +description: |
>> + The S2MU005 is a companion power management IC which includes subdevices for
>> + a charger controller, an MUIC (Micro USB Interface Controller), and flash and
>> + RGB LED controllers.
>> +
>> +allOf:
>> + - $ref: /schemas/power/supply/power-supply.yaml#
>> +
>> +properties:
>> + compatible:
>> + const: samsung,s2mu005-pmic
>> +
>> + flash:
>> + $ref: /schemas/leds/samsung,s2mu005-flash.yaml
>> + description:
>> + Child node describing flash LEDs.
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + muic:
>> + $ref: /schemas/extcon/samsung,s2mu005-muic.yaml#
>> + description:
>> + Child node describing MUIC device.
>> +
>> + multi-led:
>> + type: object
>> +
>> + allOf:
>> + - $ref: /schemas/leds/leds-class-multicolor.yaml#
>
> Does this need to be an allOf when the other refs are not?
It has it's own properties, that's the reason. This used to be it's own
thing in dt-bindings/leds, but I was asked to move it here in prior
reviews.
>> +
>> + properties:
>> + compatible:
>> + const: samsung,s2mu005-rgb
>> +
>> + required:
>> + - compatible
>> +
>> + unevaluatedProperties: false
>> +
>> + reg:
>> + maxItems: 1
>
> Move this above the child nodes please.
But properties are sorted in lex order?
> Otherwise, I think this looks good.
>
> pw-bot: changes-requested
>
> Thanks,
> Conor.
>
>> +
>> +required:
>> + - compatible
>> + - reg
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/interrupt-controller/irq.h>
>> + #include <dt-bindings/leds/common.h>
>> +
>> + i2c {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + pmic@3d {
>> + compatible = "samsung,s2mu005-pmic";
>> + reg = <0x3d>;
>> + interrupt-parent = <&gpa2>;
>> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
>> +
>> + monitored-battery = <&battery>;
>> +
>> + flash {
>> + compatible = "samsung,s2mu005-flash";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + led@0 {
>> + reg = <0>;
>> + color = <LED_COLOR_ID_WHITE>;
>> + function = LED_FUNCTION_FLASH;
>> + };
>> +
>> + led@1 {
>> + reg = <1>;
>> + color = <LED_COLOR_ID_WHITE>;
>> + function = LED_FUNCTION_FLASH;
>> + function-enumerator = <1>;
>> + };
>> + };
>> +
>> + muic {
>> + compatible = "samsung,s2mu005-muic";
>> +
>> + connector {
>> + compatible = "usb-b-connector";
>> + label = "micro-USB";
>> + type = "micro";
>> + };
>> +
>> + port {
>> + muic_to_usb: endpoint {
>> + remote-endpoint = <&usb_to_muic>;
>> + };
>> + };
>> + };
>> +
>> + multi-led {
>> + compatible = "samsung,s2mu005-rgb";
>> + color = <LED_COLOR_ID_RGB>;
>> + function = LED_FUNCTION_INDICATOR;
>> + linux,default-trigger = "pattern";
>> + };
>> + };
>> + };
>>
>> --
>> 2.53.0
>>
^ permalink raw reply
* Re: [PATCH v6 02/11] dt-bindings: extcon: document Samsung S2M series PMIC extcon device
From: Kaustabh Chakraborty @ 2026-05-15 21:07 UTC (permalink / raw)
To: Conor Dooley, Kaustabh Chakraborty
Cc: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, linux-leds, devicetree,
linux-kernel, linux-pm, linux-samsung-soc, linux-rtc, linux-doc
In-Reply-To: <20260515-mutable-urgency-305fecf3ffc4@spud>
On 2026-05-15 18:15 +01:00, Conor Dooley wrote:
> On Fri, May 15, 2026 at 04:08:58PM +0530, Kaustabh Chakraborty wrote:
>> Certain Samsung S2M series PMICs have a MUIC device which reports
>> various cable states by measuring the ID-GND resistance with an internal
>> ADC. Document the devicetree schema for this device.
>>
>> Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> pw-bot: not-applicable
Thanks, but this patch has already been reviewed by Krzysztof in v5. I
missed the Reviewed-by tags, sorry! I'd been preparing v7 after the
reviews by Sashiko.
^ permalink raw reply
* Re: [PATCH v6 02/11] dt-bindings: extcon: document Samsung S2M series PMIC extcon device
From: Conor Dooley @ 2026-05-15 17:15 UTC (permalink / raw)
To: Kaustabh Chakraborty
Cc: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, linux-leds, devicetree,
linux-kernel, linux-pm, linux-samsung-soc, linux-rtc, linux-doc
In-Reply-To: <20260515-s2mu005-pmic-v6-2-1979106992d4@disroot.org>
[-- Attachment #1: Type: text/plain, Size: 419 bytes --]
On Fri, May 15, 2026 at 04:08:58PM +0530, Kaustabh Chakraborty wrote:
> Certain Samsung S2M series PMICs have a MUIC device which reports
> various cable states by measuring the ID-GND resistance with an internal
> ADC. Document the devicetree schema for this device.
>
> Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply
* Re: [PATCH v6 03/11] dt-bindings: mfd: add documentation for S2MU005 PMIC
From: Conor Dooley @ 2026-05-15 17:14 UTC (permalink / raw)
To: Kaustabh Chakraborty
Cc: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński, linux-leds, devicetree,
linux-kernel, linux-pm, linux-samsung-soc, linux-rtc, linux-doc
In-Reply-To: <20260515-s2mu005-pmic-v6-3-1979106992d4@disroot.org>
[-- Attachment #1: Type: text/plain, Size: 4515 bytes --]
On Fri, May 15, 2026 at 04:08:59PM +0530, Kaustabh Chakraborty wrote:
> Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
> USB Interface Controller), and flash and RGB LED controllers.
>
> Add the compatible and documentation for the S2MU005 PMIC. Also, add an
> example for nodes for supported sub-devices, i.e. MUIC, flash LEDs, and
> RGB LEDs. Charger sub-device uses the node of the parent.
>
> Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
> ---
> .../bindings/mfd/samsung,s2mu005-pmic.yaml | 120 +++++++++++++++++++++
> 1 file changed, 120 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
> new file mode 100644
> index 0000000000000..0e6afb7d2017b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
> @@ -0,0 +1,120 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/samsung,s2mu005-pmic.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Samsung S2MU005 Power Management IC
> +
> +maintainers:
> + - Kaustabh Chakraborty <kauschluss@disroot.org>
> +
> +description: |
> + The S2MU005 is a companion power management IC which includes subdevices for
> + a charger controller, an MUIC (Micro USB Interface Controller), and flash and
> + RGB LED controllers.
> +
> +allOf:
> + - $ref: /schemas/power/supply/power-supply.yaml#
> +
> +properties:
> + compatible:
> + const: samsung,s2mu005-pmic
> +
> + flash:
> + $ref: /schemas/leds/samsung,s2mu005-flash.yaml
> + description:
> + Child node describing flash LEDs.
> +
> + interrupts:
> + maxItems: 1
> +
> + muic:
> + $ref: /schemas/extcon/samsung,s2mu005-muic.yaml#
> + description:
> + Child node describing MUIC device.
> +
> + multi-led:
> + type: object
> +
> + allOf:
> + - $ref: /schemas/leds/leds-class-multicolor.yaml#
Does this need to be an allOf when the other refs are not?
> +
> + properties:
> + compatible:
> + const: samsung,s2mu005-rgb
> +
> + required:
> + - compatible
> +
> + unevaluatedProperties: false
> +
> + reg:
> + maxItems: 1
Move this above the child nodes please.
Otherwise, I think this looks good.
pw-bot: changes-requested
Thanks,
Conor.
> +
> +required:
> + - compatible
> + - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/leds/common.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmic@3d {
> + compatible = "samsung,s2mu005-pmic";
> + reg = <0x3d>;
> + interrupt-parent = <&gpa2>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + monitored-battery = <&battery>;
> +
> + flash {
> + compatible = "samsung,s2mu005-flash";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + led@0 {
> + reg = <0>;
> + color = <LED_COLOR_ID_WHITE>;
> + function = LED_FUNCTION_FLASH;
> + };
> +
> + led@1 {
> + reg = <1>;
> + color = <LED_COLOR_ID_WHITE>;
> + function = LED_FUNCTION_FLASH;
> + function-enumerator = <1>;
> + };
> + };
> +
> + muic {
> + compatible = "samsung,s2mu005-muic";
> +
> + connector {
> + compatible = "usb-b-connector";
> + label = "micro-USB";
> + type = "micro";
> + };
> +
> + port {
> + muic_to_usb: endpoint {
> + remote-endpoint = <&usb_to_muic>;
> + };
> + };
> + };
> +
> + multi-led {
> + compatible = "samsung,s2mu005-rgb";
> + color = <LED_COLOR_ID_RGB>;
> + function = LED_FUNCTION_INDICATOR;
> + linux,default-trigger = "pattern";
> + };
> + };
> + };
>
> --
> 2.53.0
>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply
* [PATCH v1] rtc: Use named initializers for arrays of i2c_device_data
From: Uwe Kleine-König (The Capable Hub) @ 2026-05-15 15:47 UTC (permalink / raw)
To: Alexandre Belloni
Cc: Antoniu Miclaus, Andrew Jeffery, Avi Fishman, Tomer Maimon,
Tali Perry, Patrick Venture, Nancy Yuen, Benjamin Fair,
Tóth János, Dianlong Li, linux-rtc, linux-kernel,
openbmc
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify usage of whitespace and commas.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
---
Hello,
the mentioned change to i2c_device_id is the following:
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index 23ff24080dfd..aebd3a5e90af 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -477,7 +477,11 @@ struct rpmsg_device_id {
struct i2c_device_id {
char name[I2C_NAME_SIZE];
- kernel_ulong_t driver_data; /* Data private to the driver */
+ union {
+ /* Data private to the driver */
+ kernel_ulong_t driver_data;
+ const void *driver_data_ptr;
+ };
};
/* pci_epf */
and this requires that .driver_data is assigned via a named initializer
for static data. This requirement isn't a bad one because named
initializers are also much better readable than list initializers.
The union added to struct i2c_device_id enables further cleanups like:
diff --git a/drivers/regulator/ad5398.c b/drivers/regulator/ad5398.c
index 0123ca8157a8..dfb0b07500a7 100644
--- a/drivers/regulator/ad5398.c
+++ b/drivers/regulator/ad5398.c
@@ -207,8 +207,8 @@ struct ad5398_current_data_format {
static const struct ad5398_current_data_format df_10_4_120 = {10, 4, 0, 120000};
static const struct i2c_device_id ad5398_id[] = {
- { .name = "ad5398", .driver_data = (kernel_ulong_t)&df_10_4_120 },
- { .name = "ad5821", .driver_data = (kernel_ulong_t)&df_10_4_120 },
+ { .name = "ad5398", .driver_data_ptr = &df_10_4_120 },
+ { .name = "ad5821", .driver_data_ptr = &df_10_4_120 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ad5398_id);
@@ -219,8 +219,7 @@ static int ad5398_probe(struct i2c_client *client)
struct regulator_init_data *init_data = dev_get_platdata(&client->dev);
struct regulator_config config = { };
struct ad5398_chip_info *chip;
- const struct ad5398_current_data_format *df =
- (struct ad5398_current_data_format *)id->driver_data;
+ const struct ad5398_current_data_format *df = id->driver_data;
chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
if (!chip)
that are an improvement for readability (again!) and it keeps some
properties of the pointers (here: being const) without having to pay
attention for that. (I didn't find a nice rtc driver that benefits, so
this is "only" a regulator driver example.)
My additional motivation for this effort is CHERI[1]. This is a hardware
extension that uses 128 bit pointers but unsigned long is still 64 bit.
So with CHERI you cannot store pointers in unsigned long variables.
Best regards
Uwe
[1] https://cheri-alliance.org/discover-cheri/
https://lwn.net/Articles/1037974/
drivers/rtc/rtc-ab-b5ze-s3.c | 2 +-
drivers/rtc/rtc-ab-eoz9.c | 2 +-
drivers/rtc/rtc-abx80x.c | 20 ++++++++++----------
drivers/rtc/rtc-bq32k.c | 2 +-
drivers/rtc/rtc-ds1307.c | 36 ++++++++++++++++++------------------
drivers/rtc/rtc-ds1374.c | 2 +-
drivers/rtc/rtc-ds1672.c | 2 +-
drivers/rtc/rtc-ds3232.c | 2 +-
drivers/rtc/rtc-em3027.c | 2 +-
drivers/rtc/rtc-fm3130.c | 2 +-
drivers/rtc/rtc-hym8563.c | 4 ++--
drivers/rtc/rtc-isl12022.c | 2 +-
drivers/rtc/rtc-isl12026.c | 4 ++--
drivers/rtc/rtc-isl1208.c | 10 +++++-----
drivers/rtc/rtc-m41t80.c | 22 +++++++++++-----------
drivers/rtc/rtc-max31335.c | 4 ++--
drivers/rtc/rtc-max6900.c | 2 +-
drivers/rtc/rtc-nct3018y.c | 2 +-
drivers/rtc/rtc-pcf2127.c | 8 ++++----
drivers/rtc/rtc-pcf85063.c | 12 ++++++------
drivers/rtc/rtc-pcf8523.c | 2 +-
drivers/rtc/rtc-pcf8563.c | 6 +++---
drivers/rtc/rtc-pcf8583.c | 2 +-
drivers/rtc/rtc-rs5c372.c | 12 ++++++------
drivers/rtc/rtc-rv3029c2.c | 4 ++--
drivers/rtc/rtc-rv8803.c | 8 ++++----
drivers/rtc/rtc-rx6110.c | 2 +-
drivers/rtc/rtc-rx8010.c | 2 +-
drivers/rtc/rtc-rx8025.c | 4 ++--
drivers/rtc/rtc-rx8581.c | 2 +-
drivers/rtc/rtc-s35390a.c | 2 +-
drivers/rtc/rtc-sd2405al.c | 2 +-
drivers/rtc/rtc-sd3078.c | 2 +-
drivers/rtc/rtc-x1205.c | 2 +-
34 files changed, 97 insertions(+), 97 deletions(-)
diff --git a/drivers/rtc/rtc-ab-b5ze-s3.c b/drivers/rtc/rtc-ab-b5ze-s3.c
index 684f9898d768..6439ca427c32 100644
--- a/drivers/rtc/rtc-ab-b5ze-s3.c
+++ b/drivers/rtc/rtc-ab-b5ze-s3.c
@@ -933,7 +933,7 @@ MODULE_DEVICE_TABLE(of, abb5zes3_dt_match);
#endif
static const struct i2c_device_id abb5zes3_id[] = {
- { "abb5zes3" },
+ { .name = "abb5zes3" },
{ }
};
MODULE_DEVICE_TABLE(i2c, abb5zes3_id);
diff --git a/drivers/rtc/rtc-ab-eoz9.c b/drivers/rtc/rtc-ab-eoz9.c
index de002f7a39bf..b75f4f665076 100644
--- a/drivers/rtc/rtc-ab-eoz9.c
+++ b/drivers/rtc/rtc-ab-eoz9.c
@@ -546,7 +546,7 @@ MODULE_DEVICE_TABLE(of, abeoz9_dt_match);
#endif
static const struct i2c_device_id abeoz9_id[] = {
- { "abeoz9" },
+ { .name = "abeoz9" },
{ }
};
diff --git a/drivers/rtc/rtc-abx80x.c b/drivers/rtc/rtc-abx80x.c
index 00d7de64ed3e..e5179d0208d6 100644
--- a/drivers/rtc/rtc-abx80x.c
+++ b/drivers/rtc/rtc-abx80x.c
@@ -752,16 +752,16 @@ static int abx80x_setup_nvmem(struct abx80x_priv *priv)
}
static const struct i2c_device_id abx80x_id[] = {
- { "abx80x", ABX80X },
- { "ab0801", AB0801 },
- { "ab0803", AB0803 },
- { "ab0804", AB0804 },
- { "ab0805", AB0805 },
- { "ab1801", AB1801 },
- { "ab1803", AB1803 },
- { "ab1804", AB1804 },
- { "ab1805", AB1805 },
- { "rv1805", RV1805 },
+ { .name = "abx80x", .driver_data = ABX80X },
+ { .name = "ab0801", .driver_data = AB0801 },
+ { .name = "ab0803", .driver_data = AB0803 },
+ { .name = "ab0804", .driver_data = AB0804 },
+ { .name = "ab0805", .driver_data = AB0805 },
+ { .name = "ab1801", .driver_data = AB1801 },
+ { .name = "ab1803", .driver_data = AB1803 },
+ { .name = "ab1804", .driver_data = AB1804 },
+ { .name = "ab1805", .driver_data = AB1805 },
+ { .name = "rv1805", .driver_data = RV1805 },
{ }
};
MODULE_DEVICE_TABLE(i2c, abx80x_id);
diff --git a/drivers/rtc/rtc-bq32k.c b/drivers/rtc/rtc-bq32k.c
index 7ad34539be4d..20cd92d00fa1 100644
--- a/drivers/rtc/rtc-bq32k.c
+++ b/drivers/rtc/rtc-bq32k.c
@@ -304,7 +304,7 @@ static void bq32k_remove(struct i2c_client *client)
}
static const struct i2c_device_id bq32k_id[] = {
- { "bq32000" },
+ { .name = "bq32000" },
{ }
};
MODULE_DEVICE_TABLE(i2c, bq32k_id);
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index 7205c59ff729..ee8196498443 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -1063,24 +1063,24 @@ static const struct chip_desc chips[last_ds_type] = {
};
static const struct i2c_device_id ds1307_id[] = {
- { "ds1307", ds_1307 },
- { "ds1308", ds_1308 },
- { "ds1337", ds_1337 },
- { "ds1338", ds_1338 },
- { "ds1339", ds_1339 },
- { "ds1388", ds_1388 },
- { "ds1340", ds_1340 },
- { "ds1341", ds_1341 },
- { "ds3231", ds_3231 },
- { "m41t0", m41t0 },
- { "m41t00", m41t00 },
- { "m41t11", m41t11 },
- { "mcp7940x", mcp794xx },
- { "mcp7941x", mcp794xx },
- { "pt7c4338", ds_1307 },
- { "rx8025", rx_8025 },
- { "isl12057", ds_1337 },
- { "rx8130", rx_8130 },
+ { .name = "ds1307", .driver_data = ds_1307 },
+ { .name = "ds1308", .driver_data = ds_1308 },
+ { .name = "ds1337", .driver_data = ds_1337 },
+ { .name = "ds1338", .driver_data = ds_1338 },
+ { .name = "ds1339", .driver_data = ds_1339 },
+ { .name = "ds1388", .driver_data = ds_1388 },
+ { .name = "ds1340", .driver_data = ds_1340 },
+ { .name = "ds1341", .driver_data = ds_1341 },
+ { .name = "ds3231", .driver_data = ds_3231 },
+ { .name = "m41t0", .driver_data = m41t0 },
+ { .name = "m41t00", .driver_data = m41t00 },
+ { .name = "m41t11", .driver_data = m41t11 },
+ { .name = "mcp7940x", .driver_data = mcp794xx },
+ { .name = "mcp7941x", .driver_data = mcp794xx },
+ { .name = "pt7c4338", .driver_data = ds_1307 },
+ { .name = "rx8025", .driver_data = rx_8025 },
+ { .name = "isl12057", .driver_data = ds_1337 },
+ { .name = "rx8130", .driver_data = rx_8130 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ds1307_id);
diff --git a/drivers/rtc/rtc-ds1374.c b/drivers/rtc/rtc-ds1374.c
index c2359eb86bc9..8c247215d611 100644
--- a/drivers/rtc/rtc-ds1374.c
+++ b/drivers/rtc/rtc-ds1374.c
@@ -52,7 +52,7 @@
#define DS1374_REG_TCR 0x09 /* Trickle Charge */
static const struct i2c_device_id ds1374_id[] = {
- { "ds1374" },
+ { .name = "ds1374" },
{ }
};
MODULE_DEVICE_TABLE(i2c, ds1374_id);
diff --git a/drivers/rtc/rtc-ds1672.c b/drivers/rtc/rtc-ds1672.c
index 6e5314215d00..c610beb55bb5 100644
--- a/drivers/rtc/rtc-ds1672.c
+++ b/drivers/rtc/rtc-ds1672.c
@@ -133,7 +133,7 @@ static int ds1672_probe(struct i2c_client *client)
}
static const struct i2c_device_id ds1672_id[] = {
- { "ds1672" },
+ { .name = "ds1672" },
{ }
};
MODULE_DEVICE_TABLE(i2c, ds1672_id);
diff --git a/drivers/rtc/rtc-ds3232.c b/drivers/rtc/rtc-ds3232.c
index 18f35823b4b5..d1ef9e0dad34 100644
--- a/drivers/rtc/rtc-ds3232.c
+++ b/drivers/rtc/rtc-ds3232.c
@@ -566,7 +566,7 @@ static int ds3232_i2c_probe(struct i2c_client *client)
}
static const struct i2c_device_id ds3232_id[] = {
- { "ds3232" },
+ { .name = "ds3232" },
{ }
};
MODULE_DEVICE_TABLE(i2c, ds3232_id);
diff --git a/drivers/rtc/rtc-em3027.c b/drivers/rtc/rtc-em3027.c
index dc1ccbc65dcb..d555e5d59881 100644
--- a/drivers/rtc/rtc-em3027.c
+++ b/drivers/rtc/rtc-em3027.c
@@ -129,7 +129,7 @@ static int em3027_probe(struct i2c_client *client)
}
static const struct i2c_device_id em3027_id[] = {
- { "em3027" },
+ { .name = "em3027" },
{ }
};
MODULE_DEVICE_TABLE(i2c, em3027_id);
diff --git a/drivers/rtc/rtc-fm3130.c b/drivers/rtc/rtc-fm3130.c
index f82728ebac0c..28bb6d3f644e 100644
--- a/drivers/rtc/rtc-fm3130.c
+++ b/drivers/rtc/rtc-fm3130.c
@@ -53,7 +53,7 @@ struct fm3130 {
int data_valid;
};
static const struct i2c_device_id fm3130_id[] = {
- { "fm3130" },
+ { .name = "fm3130" },
{ }
};
MODULE_DEVICE_TABLE(i2c, fm3130_id);
diff --git a/drivers/rtc/rtc-hym8563.c b/drivers/rtc/rtc-hym8563.c
index 7a170c0f9710..3156aa5f2d9f 100644
--- a/drivers/rtc/rtc-hym8563.c
+++ b/drivers/rtc/rtc-hym8563.c
@@ -564,8 +564,8 @@ static int hym8563_probe(struct i2c_client *client)
}
static const struct i2c_device_id hym8563_id[] = {
- { "hym8563" },
- {}
+ { .name = "hym8563" },
+ { }
};
MODULE_DEVICE_TABLE(i2c, hym8563_id);
diff --git a/drivers/rtc/rtc-isl12022.c b/drivers/rtc/rtc-isl12022.c
index 5fc52dc64213..bc36288854ee 100644
--- a/drivers/rtc/rtc-isl12022.c
+++ b/drivers/rtc/rtc-isl12022.c
@@ -604,7 +604,7 @@ static const struct of_device_id isl12022_dt_match[] = {
MODULE_DEVICE_TABLE(of, isl12022_dt_match);
static const struct i2c_device_id isl12022_id[] = {
- { "isl12022" },
+ { .name = "isl12022" },
{ }
};
MODULE_DEVICE_TABLE(i2c, isl12022_id);
diff --git a/drivers/rtc/rtc-isl12026.c b/drivers/rtc/rtc-isl12026.c
index 45a2c9f676c5..b86a325d8a23 100644
--- a/drivers/rtc/rtc-isl12026.c
+++ b/drivers/rtc/rtc-isl12026.c
@@ -485,8 +485,8 @@ static const struct of_device_id isl12026_dt_match[] = {
MODULE_DEVICE_TABLE(of, isl12026_dt_match);
static const struct i2c_device_id isl12026_id[] = {
- { "isl12026" },
- { },
+ { .name = "isl12026" },
+ { }
};
MODULE_DEVICE_TABLE(i2c, isl12026_id);
diff --git a/drivers/rtc/rtc-isl1208.c b/drivers/rtc/rtc-isl1208.c
index f71a6bb77b2a..bcaa766a5068 100644
--- a/drivers/rtc/rtc-isl1208.c
+++ b/drivers/rtc/rtc-isl1208.c
@@ -110,11 +110,11 @@ static const struct isl1208_config config_raa215300_a0 = {
};
static const struct i2c_device_id isl1208_id[] = {
- { "isl1208", .driver_data = (kernel_ulong_t)&config_isl1208 },
- { "isl1209", .driver_data = (kernel_ulong_t)&config_isl1209 },
- { "isl1218", .driver_data = (kernel_ulong_t)&config_isl1218 },
- { "isl1219", .driver_data = (kernel_ulong_t)&config_isl1219 },
- { "raa215300_a0", .driver_data = (kernel_ulong_t)&config_raa215300_a0 },
+ { .name = "isl1208", .driver_data = (kernel_ulong_t)&config_isl1208 },
+ { .name = "isl1209", .driver_data = (kernel_ulong_t)&config_isl1209 },
+ { .name = "isl1218", .driver_data = (kernel_ulong_t)&config_isl1218 },
+ { .name = "isl1219", .driver_data = (kernel_ulong_t)&config_isl1219 },
+ { .name = "raa215300_a0", .driver_data = (kernel_ulong_t)&config_raa215300_a0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, isl1208_id);
diff --git a/drivers/rtc/rtc-m41t80.c b/drivers/rtc/rtc-m41t80.c
index b26afef37d9c..3c8c379392c1 100644
--- a/drivers/rtc/rtc-m41t80.c
+++ b/drivers/rtc/rtc-m41t80.c
@@ -71,17 +71,17 @@
#define M41T80_FEATURE_SQ_ALT BIT(4) /* RSx bits are in reg 4 */
static const struct i2c_device_id m41t80_id[] = {
- { "m41t62", M41T80_FEATURE_SQ | M41T80_FEATURE_SQ_ALT },
- { "m41t65", M41T80_FEATURE_WD },
- { "m41t80", M41T80_FEATURE_SQ },
- { "m41t81", M41T80_FEATURE_HT | M41T80_FEATURE_SQ},
- { "m41t81s", M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
- { "m41t82", M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
- { "m41t83", M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
- { "m41st84", M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
- { "m41st85", M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
- { "m41st87", M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
- { "rv4162", M41T80_FEATURE_SQ | M41T80_FEATURE_WD | M41T80_FEATURE_SQ_ALT },
+ { .name = "m41t62", .driver_data = M41T80_FEATURE_SQ | M41T80_FEATURE_SQ_ALT },
+ { .name = "m41t65", .driver_data = M41T80_FEATURE_WD },
+ { .name = "m41t80", .driver_data = M41T80_FEATURE_SQ },
+ { .name = "m41t81", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_SQ},
+ { .name = "m41t81s", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
+ { .name = "m41t82", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
+ { .name = "m41t83", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
+ { .name = "m41st84", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
+ { .name = "m41st85", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
+ { .name = "m41st87", .driver_data = M41T80_FEATURE_HT | M41T80_FEATURE_BL | M41T80_FEATURE_SQ },
+ { .name = "rv4162", .driver_data = M41T80_FEATURE_SQ | M41T80_FEATURE_WD | M41T80_FEATURE_SQ_ALT },
{ }
};
MODULE_DEVICE_TABLE(i2c, m41t80_id);
diff --git a/drivers/rtc/rtc-max31335.c b/drivers/rtc/rtc-max31335.c
index 952b455071d6..595816973851 100644
--- a/drivers/rtc/rtc-max31335.c
+++ b/drivers/rtc/rtc-max31335.c
@@ -745,8 +745,8 @@ static int max31335_probe(struct i2c_client *client)
}
static const struct i2c_device_id max31335_id[] = {
- { "max31331", (kernel_ulong_t)&chip[ID_MAX31331] },
- { "max31335", (kernel_ulong_t)&chip[ID_MAX31335] },
+ { .name = "max31331", .driver_data = (kernel_ulong_t)&chip[ID_MAX31331] },
+ { .name = "max31335", .driver_data = (kernel_ulong_t)&chip[ID_MAX31335] },
{ }
};
diff --git a/drivers/rtc/rtc-max6900.c b/drivers/rtc/rtc-max6900.c
index 7be31fce5bc7..8ef6d0fcd032 100644
--- a/drivers/rtc/rtc-max6900.c
+++ b/drivers/rtc/rtc-max6900.c
@@ -215,7 +215,7 @@ static int max6900_probe(struct i2c_client *client)
}
static const struct i2c_device_id max6900_id[] = {
- { "max6900" },
+ { .name = "max6900" },
{ }
};
MODULE_DEVICE_TABLE(i2c, max6900_id);
diff --git a/drivers/rtc/rtc-nct3018y.c b/drivers/rtc/rtc-nct3018y.c
index cd4b1db902e9..700a395fad3a 100644
--- a/drivers/rtc/rtc-nct3018y.c
+++ b/drivers/rtc/rtc-nct3018y.c
@@ -572,7 +572,7 @@ static int nct3018y_probe(struct i2c_client *client)
}
static const struct i2c_device_id nct3018y_id[] = {
- { "nct3018y" },
+ { .name = "nct3018y" },
{ }
};
MODULE_DEVICE_TABLE(i2c, nct3018y_id);
diff --git a/drivers/rtc/rtc-pcf2127.c b/drivers/rtc/rtc-pcf2127.c
index e4785c5a55d0..1995e9f2756d 100644
--- a/drivers/rtc/rtc-pcf2127.c
+++ b/drivers/rtc/rtc-pcf2127.c
@@ -1449,10 +1449,10 @@ static const struct regmap_bus pcf2127_i2c_regmap = {
static struct i2c_driver pcf2127_i2c_driver;
static const struct i2c_device_id pcf2127_i2c_id[] = {
- { "pcf2127", (kernel_ulong_t)&pcf21xx_cfg[PCF2127] },
- { "pcf2129", (kernel_ulong_t)&pcf21xx_cfg[PCF2129] },
- { "pca2129", (kernel_ulong_t)&pcf21xx_cfg[PCF2129] },
- { "pcf2131", (kernel_ulong_t)&pcf21xx_cfg[PCF2131] },
+ { .name = "pcf2127", .driver_data = (kernel_ulong_t)&pcf21xx_cfg[PCF2127] },
+ { .name = "pcf2129", .driver_data = (kernel_ulong_t)&pcf21xx_cfg[PCF2129] },
+ { .name = "pca2129", .driver_data = (kernel_ulong_t)&pcf21xx_cfg[PCF2129] },
+ { .name = "pcf2131", .driver_data = (kernel_ulong_t)&pcf21xx_cfg[PCF2131] },
{ }
};
MODULE_DEVICE_TABLE(i2c, pcf2127_i2c_id);
diff --git a/drivers/rtc/rtc-pcf85063.c b/drivers/rtc/rtc-pcf85063.c
index f643e0bd7351..01e209d88f5f 100644
--- a/drivers/rtc/rtc-pcf85063.c
+++ b/drivers/rtc/rtc-pcf85063.c
@@ -665,12 +665,12 @@ static const struct pcf85063_config config_rv8263 = {
};
static const struct i2c_device_id pcf85063_ids[] = {
- { "pca85073a", .driver_data = (kernel_ulong_t)&config_pcf85063a },
- { "pcf85063", .driver_data = (kernel_ulong_t)&config_pcf85063 },
- { "pcf85063tp", .driver_data = (kernel_ulong_t)&config_pcf85063tp },
- { "pcf85063a", .driver_data = (kernel_ulong_t)&config_pcf85063a },
- { "rv8263", .driver_data = (kernel_ulong_t)&config_rv8263 },
- {}
+ { .name = "pca85073a", .driver_data = (kernel_ulong_t)&config_pcf85063a },
+ { .name = "pcf85063", .driver_data = (kernel_ulong_t)&config_pcf85063 },
+ { .name = "pcf85063tp", .driver_data = (kernel_ulong_t)&config_pcf85063tp },
+ { .name = "pcf85063a", .driver_data = (kernel_ulong_t)&config_pcf85063a },
+ { .name = "rv8263", .driver_data = (kernel_ulong_t)&config_rv8263 },
+ { }
};
MODULE_DEVICE_TABLE(i2c, pcf85063_ids);
diff --git a/drivers/rtc/rtc-pcf8523.c b/drivers/rtc/rtc-pcf8523.c
index 2c63c0ffd05a..e8354953836c 100644
--- a/drivers/rtc/rtc-pcf8523.c
+++ b/drivers/rtc/rtc-pcf8523.c
@@ -495,7 +495,7 @@ static int pcf8523_probe(struct i2c_client *client)
}
static const struct i2c_device_id pcf8523_id[] = {
- { "pcf8523" },
+ { .name = "pcf8523" },
{ }
};
MODULE_DEVICE_TABLE(i2c, pcf8523_id);
diff --git a/drivers/rtc/rtc-pcf8563.c b/drivers/rtc/rtc-pcf8563.c
index b281e9489df1..81d13733b1e9 100644
--- a/drivers/rtc/rtc-pcf8563.c
+++ b/drivers/rtc/rtc-pcf8563.c
@@ -557,9 +557,9 @@ static int pcf8563_probe(struct i2c_client *client)
}
static const struct i2c_device_id pcf8563_id[] = {
- { "pcf8563" },
- { "rtc8564" },
- { "pca8565" },
+ { .name = "pcf8563" },
+ { .name = "rtc8564" },
+ { .name = "pca8565" },
{ }
};
MODULE_DEVICE_TABLE(i2c, pcf8563_id);
diff --git a/drivers/rtc/rtc-pcf8583.c b/drivers/rtc/rtc-pcf8583.c
index 652b9dfa7566..df5e20cbc26c 100644
--- a/drivers/rtc/rtc-pcf8583.c
+++ b/drivers/rtc/rtc-pcf8583.c
@@ -297,7 +297,7 @@ static int pcf8583_probe(struct i2c_client *client)
}
static const struct i2c_device_id pcf8583_id[] = {
- { "pcf8583" },
+ { .name = "pcf8583" },
{ }
};
MODULE_DEVICE_TABLE(i2c, pcf8583_id);
diff --git a/drivers/rtc/rtc-rs5c372.c b/drivers/rtc/rtc-rs5c372.c
index 936f4f05c8c7..24bd795d9d95 100644
--- a/drivers/rtc/rtc-rs5c372.c
+++ b/drivers/rtc/rtc-rs5c372.c
@@ -75,12 +75,12 @@ enum rtc_type {
};
static const struct i2c_device_id rs5c372_id[] = {
- { "r2025sd", rtc_r2025sd },
- { "r2221tl", rtc_r2221tl },
- { "rs5c372a", rtc_rs5c372a },
- { "rs5c372b", rtc_rs5c372b },
- { "rv5c386", rtc_rv5c386 },
- { "rv5c387a", rtc_rv5c387a },
+ { .name = "r2025sd", .driver_data = rtc_r2025sd },
+ { .name = "r2221tl", .driver_data = rtc_r2221tl },
+ { .name = "rs5c372a", .driver_data = rtc_rs5c372a },
+ { .name = "rs5c372b", .driver_data = rtc_rs5c372b },
+ { .name = "rv5c386", .driver_data = rtc_rv5c386 },
+ { .name = "rv5c387a", .driver_data = rtc_rv5c387a },
{ }
};
MODULE_DEVICE_TABLE(i2c, rs5c372_id);
diff --git a/drivers/rtc/rtc-rv3029c2.c b/drivers/rtc/rtc-rv3029c2.c
index 83331d1fcab0..98953af2a24a 100644
--- a/drivers/rtc/rtc-rv3029c2.c
+++ b/drivers/rtc/rtc-rv3029c2.c
@@ -807,8 +807,8 @@ static int rv3029_i2c_probe(struct i2c_client *client)
}
static const struct i2c_device_id rv3029_id[] = {
- { "rv3029" },
- { "rv3029c2" },
+ { .name = "rv3029" },
+ { .name = "rv3029c2" },
{ }
};
MODULE_DEVICE_TABLE(i2c, rv3029_id);
diff --git a/drivers/rtc/rtc-rv8803.c b/drivers/rtc/rtc-rv8803.c
index 2bf988a89fd7..b9b5fee16ee4 100644
--- a/drivers/rtc/rtc-rv8803.c
+++ b/drivers/rtc/rtc-rv8803.c
@@ -631,10 +631,10 @@ static int rv8803_suspend(struct device *dev)
static DEFINE_SIMPLE_DEV_PM_OPS(rv8803_pm_ops, rv8803_suspend, rv8803_resume);
static const struct i2c_device_id rv8803_id[] = {
- { "rv8803", rv_8803 },
- { "rv8804", rx_8804 },
- { "rx8803", rx_8803 },
- { "rx8900", rx_8900 },
+ { .name = "rv8803", .driver_data = rv_8803 },
+ { .name = "rv8804", .driver_data = rx_8804 },
+ { .name = "rx8803", .driver_data = rx_8803 },
+ { .name = "rx8900", .driver_data = rx_8900 },
{ }
};
MODULE_DEVICE_TABLE(i2c, rv8803_id);
diff --git a/drivers/rtc/rtc-rx6110.c b/drivers/rtc/rtc-rx6110.c
index 07bf35ac8d79..1eacd470a27c 100644
--- a/drivers/rtc/rtc-rx6110.c
+++ b/drivers/rtc/rtc-rx6110.c
@@ -449,7 +449,7 @@ static const struct acpi_device_id rx6110_i2c_acpi_match[] = {
MODULE_DEVICE_TABLE(acpi, rx6110_i2c_acpi_match);
static const struct i2c_device_id rx6110_i2c_id[] = {
- { "rx6110" },
+ { .name = "rx6110" },
{ }
};
MODULE_DEVICE_TABLE(i2c, rx6110_i2c_id);
diff --git a/drivers/rtc/rtc-rx8010.c b/drivers/rtc/rtc-rx8010.c
index 171240e50f48..ce3954132336 100644
--- a/drivers/rtc/rtc-rx8010.c
+++ b/drivers/rtc/rtc-rx8010.c
@@ -50,7 +50,7 @@
#define RX8010_ALARM_AE BIT(7)
static const struct i2c_device_id rx8010_id[] = {
- { "rx8010" },
+ { .name = "rx8010" },
{ }
};
MODULE_DEVICE_TABLE(i2c, rx8010_id);
diff --git a/drivers/rtc/rtc-rx8025.c b/drivers/rtc/rtc-rx8025.c
index c57081f9e02b..5eeaa929f3ef 100644
--- a/drivers/rtc/rtc-rx8025.c
+++ b/drivers/rtc/rtc-rx8025.c
@@ -71,8 +71,8 @@ enum rx_model {
};
static const struct i2c_device_id rx8025_id[] = {
- { "rx8025", model_rx_8025 },
- { "rx8035", model_rx_8035 },
+ { .name = "rx8025", .driver_data = model_rx_8025 },
+ { .name = "rx8035", .driver_data = model_rx_8035 },
{ }
};
MODULE_DEVICE_TABLE(i2c, rx8025_id);
diff --git a/drivers/rtc/rtc-rx8581.c b/drivers/rtc/rtc-rx8581.c
index 20c2dff01bae..cf4dab94c337 100644
--- a/drivers/rtc/rtc-rx8581.c
+++ b/drivers/rtc/rtc-rx8581.c
@@ -294,7 +294,7 @@ static int rx8581_probe(struct i2c_client *client)
}
static const struct i2c_device_id rx8581_id[] = {
- { "rx8581" },
+ { .name = "rx8581" },
{ }
};
MODULE_DEVICE_TABLE(i2c, rx8581_id);
diff --git a/drivers/rtc/rtc-s35390a.c b/drivers/rtc/rtc-s35390a.c
index a4678d7c6cf6..31394f34fb70 100644
--- a/drivers/rtc/rtc-s35390a.c
+++ b/drivers/rtc/rtc-s35390a.c
@@ -51,7 +51,7 @@
#define S35390A_INT2_MODE_PMIN (BIT(3) | BIT(2)) /* INT2FE | INT2ME */
static const struct i2c_device_id s35390a_id[] = {
- { "s35390a" },
+ { .name = "s35390a" },
{ }
};
MODULE_DEVICE_TABLE(i2c, s35390a_id);
diff --git a/drivers/rtc/rtc-sd2405al.c b/drivers/rtc/rtc-sd2405al.c
index 708ea5d964de..7982a910a537 100644
--- a/drivers/rtc/rtc-sd2405al.c
+++ b/drivers/rtc/rtc-sd2405al.c
@@ -202,7 +202,7 @@ static int sd2405al_probe(struct i2c_client *client)
}
static const struct i2c_device_id sd2405al_id[] = {
- { "sd2405al" },
+ { .name = "sd2405al" },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(i2c, sd2405al_id);
diff --git a/drivers/rtc/rtc-sd3078.c b/drivers/rtc/rtc-sd3078.c
index 10cc1dcfc774..2c61f0e204a4 100644
--- a/drivers/rtc/rtc-sd3078.c
+++ b/drivers/rtc/rtc-sd3078.c
@@ -186,7 +186,7 @@ static int sd3078_probe(struct i2c_client *client)
}
static const struct i2c_device_id sd3078_id[] = {
- { "sd3078" },
+ { .name = "sd3078" },
{ }
};
MODULE_DEVICE_TABLE(i2c, sd3078_id);
diff --git a/drivers/rtc/rtc-x1205.c b/drivers/rtc/rtc-x1205.c
index b8a0fccef14e..bb1a5c86f621 100644
--- a/drivers/rtc/rtc-x1205.c
+++ b/drivers/rtc/rtc-x1205.c
@@ -663,7 +663,7 @@ static void x1205_remove(struct i2c_client *client)
}
static const struct i2c_device_id x1205_id[] = {
- { "x1205" },
+ { .name = "x1205" },
{ }
};
MODULE_DEVICE_TABLE(i2c, x1205_id);
base-commit: 254f49634ee16a731174d2ae34bc50bd5f45e731
--
2.47.3
^ permalink raw reply related
* Re: [PATCH v4 1/1] mfd: Add Host Interface (HIF) support for Nuvoton NCT6694
From: Guenter Roeck @ 2026-05-15 14:04 UTC (permalink / raw)
To: Andrew Lunn, a0282524688
Cc: tmyu0, linusw, brgl, andi.shyti, lee, mkl, mailhol,
alexandre.belloni, wim, linux-kernel, linux-gpio, linux-i2c,
linux-can, netdev, linux-watchdog, linux-hwmon, linux-rtc,
linux-usb
In-Reply-To: <ef9449dc-ef2a-415e-8acc-a15f349bac24@lunn.ch>
On 5/15/26 05:41, Andrew Lunn wrote:
>> MAINTAINERS | 1 +
>> drivers/gpio/gpio-nct6694.c | 7 -
>> drivers/hwmon/nct6694-hwmon.c | 21 -
>> drivers/i2c/busses/i2c-nct6694.c | 7 -
>> drivers/mfd/Kconfig | 47 +-
>> drivers/mfd/Makefile | 3 +-
>> drivers/mfd/nct6694-hif.c | 663 ++++++++++++++++++++++++++++
>> drivers/mfd/nct6694.c | 111 +++--
>> drivers/net/can/usb/nct6694_canfd.c | 6 -
>
> The networking change here is very small, so my influence as a
> networking Maintainer should be considered small.
>
> However, i would say this patch is too big, does too many different
> things at once, making it harder to review. Please could you break it
> up into lots of small patches, each with good commit messages, and
> being obviously correct.
>
Add my influence as hardware monitoring maintainer. I very much agree.
Guenter
^ permalink raw reply
* Re: [PATCH v4 1/1] mfd: Add Host Interface (HIF) support for Nuvoton NCT6694
From: Andrew Lunn @ 2026-05-15 12:41 UTC (permalink / raw)
To: a0282524688
Cc: tmyu0, linusw, brgl, linux, andi.shyti, lee, mkl, mailhol,
alexandre.belloni, wim, linux-kernel, linux-gpio, linux-i2c,
linux-can, netdev, linux-watchdog, linux-hwmon, linux-rtc,
linux-usb
In-Reply-To: <20260515085746.114361-2-a0282524688@gmail.com>
> MAINTAINERS | 1 +
> drivers/gpio/gpio-nct6694.c | 7 -
> drivers/hwmon/nct6694-hwmon.c | 21 -
> drivers/i2c/busses/i2c-nct6694.c | 7 -
> drivers/mfd/Kconfig | 47 +-
> drivers/mfd/Makefile | 3 +-
> drivers/mfd/nct6694-hif.c | 663 ++++++++++++++++++++++++++++
> drivers/mfd/nct6694.c | 111 +++--
> drivers/net/can/usb/nct6694_canfd.c | 6 -
The networking change here is very small, so my influence as a
networking Maintainer should be considered small.
However, i would say this patch is too big, does too many different
things at once, making it harder to review. Please could you break it
up into lots of small patches, each with good commit messages, and
being obviously correct.
> +F: drivers/mfd/nct6694-hif.c
Maybe move all the usb code into nct6694-usb.c ?
> - * USB command module type for NCT6694 GPIO controller.
> - * This defines the module type used for communication with the NCT6694
> - * GPIO controller over the USB interface.
> - */
> -#define NCT6694_GPIO_MOD 0xFF
> -
> #define NCT6694_GPIO_VER 0x90
> #define NCT6694_GPIO_VALID 0x110
> #define NCT6694_GPI_DATA 0x120
Moving code from one place to another can be a patch. Just moving code
is quick and easy to review, and it gets it out of more complex
patches which are harder to review.
> +static int nct6694_response_err_handling(struct nct6694 *nct6694, unsigned char err_status)
> +{
> + switch (err_status) {
> + case NCT6694_NO_ERROR:
> + return 0;
> + case NCT6694_NOT_SUPPORT_ERROR:
> + dev_err(nct6694->dev, "Command is not supported!\n");
> + break;
Maybe EOPNOTSUPP?
> + case NCT6694_NO_RESPONSE_ERROR:
> + dev_warn(nct6694->dev, "Command received no response!\n");
> + break;
> + case NCT6694_TIMEOUT_ERROR:
> + dev_warn(nct6694->dev, "Command timed out!\n");
> + break;
Maybe ETIMEDOUT?
> + case NCT6694_PENDING:
> + dev_err(nct6694->dev, "Command is pending!\n");
> + break;
EBUSY?
Having different error codes can make it easier to debug when things
so wrong. But you also have dev_err(), so it is less important.
> -static int nct6694_response_err_handling(struct nct6694 *nct6694, unsigned char err_status)
> +static int nct6694_usb_err_handling(struct nct6694 *nct6694,
> + unsigned char err_status)
These renames can happen in one patch. Again, it is quick and easy to
review.
>
> - guard(mutex)(&nct6694->access_lock);
> + guard(mutex)(&udata->access_lock);
This change is not obviously correct. Can moving the lock be made of
patch of its own, with an explanation of why?
> - nct6694->usb_msg = devm_kzalloc(dev, sizeof(union nct6694_usb_msg), GFP_KERNEL);
> - if (!nct6694->usb_msg)
> + udata = devm_kzalloc(dev, sizeof(*udata), GFP_KERNEL);
> + if (!udata)
> return -ENOMEM;
>
> - nct6694->int_buffer = devm_kzalloc(dev, sizeof(*nct6694->int_buffer), GFP_KERNEL);
> - if (!nct6694->int_buffer)
> + udata->usb_msg = devm_kzalloc(dev, sizeof(*udata->usb_msg), GFP_KERNEL);
> + if (!udata->usb_msg)
> return -ENOMEM;
>
> - nct6694->int_in_urb = usb_alloc_urb(0, GFP_KERNEL);
> - if (!nct6694->int_in_urb)
> + udata->int_buffer = devm_kzalloc(dev, sizeof(*udata->int_buffer), GFP_KERNEL);
> + if (!udata->int_buffer)
> return -ENOMEM;
>
> + udata->int_in_urb = usb_alloc_urb(0, GFP_KERNEL);
> + if (!udata->int_in_urb)
> + return -ENOMEM;
In this hunk, diff(1) has done a poor job and made it harder to
review. If i understand the code correctly, udata contains USB
specific data? Maybe call it usdata? That also has the same length as
ntc6694, which has some minor advantages. What you might find is that
if you have a patch adding only the allocation of usbdata, and then a
patch moving things into usbdata, diff(1) does a better job, and the
code is more obviously correct.
> @@ -305,16 +344,15 @@ static int nct6694_usb_probe(struct usb_interface *iface,
> }
>
> nct6694->dev = dev;
> - nct6694->udev = udev;
> +
> + spin_lock_init(&nct6694->irq_lock);
>
> ida_init(&nct6694->gpio_ida);
> ida_init(&nct6694->i2c_ida);
> ida_init(&nct6694->canfd_ida);
> ida_init(&nct6694->wdt_ida);
>
> - spin_lock_init(&nct6694->irq_lock);
> -
Why has the spin_lock_init() moved? Having lots of small patches would
make that stand out, and when you reviewed your own patches, you might
decided to change it back, because it does not appear to be needed.
Given the size of this patch, i'm finding it hard to see the overall
structure. Generally, when you have one device with two different
access mechanisms, you end up with three files, two implementing
access, and the third with the common code. With one big patch, i
don't see this common code.
Andrew
^ permalink raw reply
* [PATCH v6 11/11] power: supply: add support for Samsung S2M series PMIC charger device
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Add a driver for charger controllers found in certain Samsung S2M series
PMICs. The driver has very basic support for the device, with only
charger online reporting working, and USB 2.0 device negotiations
working.
The driver includes initial support for the S2MU005 PMIC charger.
Co-developed-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/power/supply/Kconfig | 11 ++
drivers/power/supply/Makefile | 1 +
drivers/power/supply/s2m-charger.c | 299 +++++++++++++++++++++++++++++++++++++
3 files changed, 311 insertions(+)
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 83392ed6a8da9..6270e6d16fbbb 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -856,6 +856,17 @@ config CHARGER_RK817
help
Say Y to include support for Rockchip RK817 Battery Charger.
+config CHARGER_S2M
+ tristate "Samsung S2M series PMIC battery charger support"
+ depends on EXTCON_S2M
+ depends on MFD_SEC_CORE
+ select REGMAP_IRQ
+ help
+ This option enables support for charger devices found in
+ certain Samsung S2M series PMICs, such as the S2MU005. These
+ devices provide USB power supply information and also required
+ for USB OTG role switching.
+
config CHARGER_SMB347
tristate "Summit Microelectronics SMB3XX Battery Charger"
depends on I2C
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 7ee839dca7f33..738814650ea0f 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -107,6 +107,7 @@ obj-$(CONFIG_CHARGER_BQ25890) += bq25890_charger.o
obj-$(CONFIG_CHARGER_BQ25980) += bq25980_charger.o
obj-$(CONFIG_CHARGER_BQ256XX) += bq256xx_charger.o
obj-$(CONFIG_CHARGER_RK817) += rk817_charger.o
+obj-$(CONFIG_CHARGER_S2M) += s2m-charger.o
obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o
obj-$(CONFIG_CHARGER_TPS65090) += tps65090-charger.o
obj-$(CONFIG_CHARGER_TPS65217) += tps65217_charger.o
diff --git a/drivers/power/supply/s2m-charger.c b/drivers/power/supply/s2m-charger.c
new file mode 100644
index 0000000000000..b32cea55b8b04
--- /dev/null
+++ b/drivers/power/supply/s2m-charger.c
@@ -0,0 +1,299 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Battery Charger Driver for Samsung S2M series PMICs.
+ *
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (c) 2026 Kaustabh Chakraborty <kauschluss@disroot.org>
+ * Copyright (c) 2026 Łukasz Lebiedziński <kernel@lvkasz.us>
+ */
+
+#include <linux/devm-helpers.h>
+#include <linux/extcon.h>
+#include <linux/mfd/samsung/core.h>
+#include <linux/mfd/samsung/s2mu005.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+
+struct s2m_chgr {
+ struct device *dev;
+ struct regmap *regmap;
+ struct power_supply *psy;
+ struct extcon_dev *extcon;
+ struct work_struct extcon_work;
+ struct notifier_block extcon_nb;
+};
+
+static int s2mu005_chgr_get_online(struct s2m_chgr *priv, int *value)
+{
+ u32 val;
+ int ret = 0;
+
+ ret = regmap_read(priv->regmap, S2MU005_REG_CHGR_STATUS0, &val);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to read register (%d)\n", ret);
+ return ret;
+ }
+
+ *value = !!(val & S2MU005_CHGR_CHG);
+
+ return ret;
+}
+
+static void s2mu005_chgr_get_usb_type(struct s2m_chgr *priv, int *value)
+{
+ if (extcon_get_state(priv->extcon, EXTCON_CHG_USB_CDP))
+ *value = POWER_SUPPLY_USB_TYPE_CDP;
+ if (extcon_get_state(priv->extcon, EXTCON_CHG_USB_SDP))
+ *value = POWER_SUPPLY_USB_TYPE_SDP;
+ if (extcon_get_state(priv->extcon, EXTCON_CHG_USB_DCP))
+ *value = POWER_SUPPLY_USB_TYPE_DCP;
+ else
+ *value = POWER_SUPPLY_USB_TYPE_UNKNOWN;
+}
+
+static int s2mu005_chgr_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct s2m_chgr *priv = power_supply_get_drvdata(psy);
+ int ret = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_ONLINE:
+ ret = s2mu005_chgr_get_online(priv, &val->intval);
+ break;
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ s2mu005_chgr_get_usb_type(priv, &val->intval);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return ret;
+}
+
+static int s2mu005_chgr_mode_set_host(struct s2m_chgr *priv)
+{
+ int ret;
+
+ /* set mode to OTG */
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_CHGR_CTRL0,
+ S2MU005_CHGR_OP_MODE,
+ FIELD_PREP(S2MU005_CHGR_OP_MODE,
+ S2MU005_CHGR_OP_MODE_OTG));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set OTG mode (%d)\n", ret);
+ return ret;
+ }
+
+ /* set boost frequency to 2MHz */
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_CHGR_CTRL11,
+ S2MU005_CHGR_OSC_BOOST,
+ FIELD_PREP(S2MU005_CHGR_OSC_BOOST,
+ S2MU005_CHGR_OSC_BOOST_2MHZ));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set boost frequency (%d)\n", ret);
+ return ret;
+ }
+
+ /* set OTG current limit to 1.5 A */
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_CHGR_CTRL4,
+ S2MU005_CHGR_OTG_OCP,
+ FIELD_PREP(S2MU005_CHGR_OTG_OCP,
+ S2MU005_CHGR_OTG_OCP_1P5A));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set OTG current limit (%d)\n", ret);
+ return ret;
+ }
+
+ /* VBUS switches are OFF when OTG over-current happens */
+ ret = regmap_set_bits(priv->regmap, S2MU005_REG_CHGR_CTRL4,
+ S2MU005_CHGR_OTG_OCP_OFF);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set OTG OCP switch (%d)\n", ret);
+ return ret;
+ }
+
+ /* set OTG voltage to 5.1 V */
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_CHGR_CTRL5,
+ S2MU005_CHGR_VMID_BOOST,
+ FIELD_PREP(S2MU005_CHGR_VMID_BOOST,
+ S2MU005_CHGR_VMID_BOOST_5P1V));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set OTG voltage (%d)\n", ret);
+ return ret;
+ }
+
+ /* turn on OTG */
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_CHGR_CTRL15,
+ S2MU005_CHGR_OTG_EN,
+ FIELD_PREP(S2MU005_CHGR_OTG_EN,
+ S2MU005_CHGR_OTG_EN_ON));
+ if (ret < 0)
+ dev_err(priv->dev, "failed to turn on OTG (%d)\n", ret);
+ return ret;
+}
+
+static int s2mu005_chgr_mode_set_charger(struct s2m_chgr *priv)
+{
+ int ret;
+
+ /* first reset to mode 0 */
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_CHGR_CTRL0,
+ S2MU005_CHGR_OP_MODE);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to reset opmode (%d)\n", ret);
+ return ret;
+ }
+
+ /* wait for the charger to settle before switching to charging mode */
+ msleep(50);
+ /* then set to charging mode */
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_CHGR_CTRL0,
+ S2MU005_CHGR_OP_MODE,
+ FIELD_PREP(S2MU005_CHGR_OP_MODE,
+ S2MU005_CHGR_OP_MODE_CHG));
+ if (ret < 0)
+ dev_err(priv->dev, "failed to set opmode to charging (%d)\n", ret);
+ return ret;
+}
+
+static int s2mu005_chgr_mode_unset(struct s2m_chgr *priv)
+{
+ int ret;
+
+ /* turn off OTG */
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_CHGR_CTRL15,
+ S2MU005_CHGR_OTG_EN);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to turn off OTG (%d)\n", ret);
+ return ret;
+ }
+
+ /* reset operation mode */
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_CHGR_CTRL0,
+ S2MU005_CHGR_OP_MODE);
+ if (ret < 0)
+ dev_err(priv->dev, "failed to reset opmode (%d)\n", ret);
+ return ret;
+}
+
+static void s2mu005_chgr_extcon_work(struct work_struct *work)
+{
+ struct s2m_chgr *priv = container_of(work, struct s2m_chgr, extcon_work);
+
+ if (extcon_get_state(priv->extcon, EXTCON_USB_HOST))
+ s2mu005_chgr_mode_set_host(priv);
+ else if (extcon_get_state(priv->extcon, EXTCON_USB))
+ s2mu005_chgr_mode_set_charger(priv);
+ else
+ s2mu005_chgr_mode_unset(priv);
+
+ power_supply_changed(priv->psy);
+}
+
+static const enum power_supply_property s2mu005_chgr_properties[] = {
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_USB_TYPE,
+};
+
+static const struct power_supply_desc s2mu005_chgr_psy_desc = {
+ .name = "s2mu005-charger",
+ .type = POWER_SUPPLY_TYPE_USB,
+ .properties = s2mu005_chgr_properties,
+ .num_properties = ARRAY_SIZE(s2mu005_chgr_properties),
+ .get_property = s2mu005_chgr_get_property,
+ .usb_types = BIT(POWER_SUPPLY_USB_TYPE_CDP) |
+ BIT(POWER_SUPPLY_USB_TYPE_SDP) |
+ BIT(POWER_SUPPLY_USB_TYPE_DCP) |
+ BIT(POWER_SUPPLY_USB_TYPE_UNKNOWN),
+};
+
+static int s2m_chgr_extcon_notifier(struct notifier_block *nb,
+ unsigned long event, void *param)
+{
+ struct s2m_chgr *priv = container_of(nb, struct s2m_chgr, extcon_nb);
+
+ schedule_work(&priv->extcon_work);
+
+ return NOTIFY_OK;
+}
+
+static int s2m_chgr_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sec_pmic_dev *pmic_drvdata = dev_get_drvdata(dev->parent);
+ struct s2m_chgr *priv;
+ struct device_node *extcon_node __free(device_node) = NULL;
+ struct power_supply_config psy_cfg = {};
+ const struct power_supply_desc *psy_desc;
+ work_func_t extcon_work_func;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+ priv->dev = dev;
+ priv->regmap = pmic_drvdata->regmap_pmic;
+
+ switch (platform_get_device_id(pdev)->driver_data) {
+ case S2MU005:
+ psy_desc = &s2mu005_chgr_psy_desc;
+ extcon_work_func = s2mu005_chgr_extcon_work;
+ break;
+ default:
+ return dev_err_probe(dev, -ENODEV,
+ "device type %d is not supported by driver\n",
+ pmic_drvdata->device_type);
+ }
+
+ psy_cfg.drv_data = priv;
+ psy_cfg.fwnode = dev_fwnode(dev->parent);
+ priv->psy = devm_power_supply_register(dev, psy_desc, &psy_cfg);
+ if (IS_ERR(priv->psy))
+ return dev_err_probe(dev, PTR_ERR(priv->psy),
+ "failed to register power supply subsystem\n");
+
+ /* MUIC is mandatory. If unavailable, request probe deferral */
+ extcon_node = of_get_child_by_name(dev->parent->of_node, "muic");
+ priv->extcon = extcon_find_edev_by_node(extcon_node);
+ if (IS_ERR(priv->extcon))
+ return -EPROBE_DEFER;
+
+ ret = devm_work_autocancel(dev, &priv->extcon_work, extcon_work_func);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to initialize extcon work\n");
+
+ priv->extcon_nb.notifier_call = s2m_chgr_extcon_notifier;
+ ret = devm_extcon_register_notifier_all(dev, priv->extcon, &priv->extcon_nb);
+ if (ret)
+ dev_err_probe(dev, ret, "failed to register extcon notifier\n");
+
+ return 0;
+}
+
+static const struct platform_device_id s2m_chgr_id_table[] = {
+ { "s2mu005-charger", S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, s2m_chgr_id_table);
+
+static struct platform_driver s2m_chgr_driver = {
+ .driver = {
+ .name = "s2m-charger",
+ },
+ .probe = s2m_chgr_probe,
+ .id_table = s2m_chgr_id_table,
+};
+module_platform_driver(s2m_chgr_driver);
+
+MODULE_DESCRIPTION("Battery Charger Driver For Samsung S2M Series PMICs");
+MODULE_AUTHOR("Kaustabh Chakraborty <kauschluss@disroot.org>");
+MODULE_AUTHOR("Łukasz Lebiedziński <kernel@lvkasz.us>");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related
* [PATCH v6 10/11] extcon: add support for Samsung S2M series PMIC extcon devices
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Add a driver for MUIC devices found in certain Samsung S2M series PMICs
These are USB port accessory detectors. These devices report multiple
cable states depending on the ID-GND resistance measured by an internal
ADC.
The driver includes initial support for the S2MU005 PMIC extcon.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/extcon/Kconfig | 10 ++
drivers/extcon/Makefile | 1 +
drivers/extcon/extcon-s2m.c | 345 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 356 insertions(+)
diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
index 68d9df7d2dae0..19c712e591955 100644
--- a/drivers/extcon/Kconfig
+++ b/drivers/extcon/Kconfig
@@ -183,6 +183,16 @@ config EXTCON_RT8973A
and switch that is optimized to protect low voltage system
from abnormal high input voltage (up to 28V).
+config EXTCON_S2M
+ tristate "Samsung S2M series PMIC EXTCON support"
+ depends on MFD_SEC_CORE
+ select REGMAP_IRQ
+ help
+ This option enables support for MUIC devices found in certain
+ Samsung S2M series PMICs, such as the S2MU005. These devices
+ have internal ADCs measuring the ID-GND resistance, thereby
+ can be used as a USB port accessory detector.
+
config EXTCON_SM5502
tristate "Silicon Mitus SM5502/SM5504/SM5703 EXTCON support"
depends on I2C
diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
index 6482f2bfd6611..e3939786f3474 100644
--- a/drivers/extcon/Makefile
+++ b/drivers/extcon/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o
obj-$(CONFIG_EXTCON_PTN5150) += extcon-ptn5150.o
obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o
obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o
+obj-$(CONFIG_EXTCON_S2M) += extcon-s2m.o
obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o
obj-$(CONFIG_EXTCON_USB_GPIO) += extcon-usb-gpio.o
obj-$(CONFIG_EXTCON_USBC_CROS_EC) += extcon-usbc-cros-ec.o
diff --git a/drivers/extcon/extcon-s2m.c b/drivers/extcon/extcon-s2m.c
new file mode 100644
index 0000000000000..e57031b0066bb
--- /dev/null
+++ b/drivers/extcon/extcon-s2m.c
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Extcon Driver for Samsung S2M series PMICs.
+ *
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (C) 2026 Kaustabh Chakraborty <kauschluss@disroot.org>
+ */
+
+#include <linux/delay.h>
+#include <linux/extcon-provider.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/samsung/core.h>
+#include <linux/mfd/samsung/s2mu005.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+struct s2m_muic {
+ struct device *dev;
+ struct regmap *regmap;
+ struct extcon_dev *extcon;
+ struct s2m_muic_irq_data *irq_data;
+ const unsigned int *extcon_cable;
+ bool attached;
+};
+
+struct s2m_muic_irq_data {
+ const char *name;
+ int (*const handler)(struct s2m_muic *);
+ int irq;
+};
+
+static int s2mu005_muic_detach(struct s2m_muic *priv)
+{
+ int ret;
+ int i;
+
+ ret = regmap_set_bits(priv->regmap, S2MU005_REG_MUIC_CTRL1,
+ S2MU005_MUIC_MAN_SW);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to disable manual switching\n");
+ return ret;
+ }
+
+ ret = regmap_set_bits(priv->regmap, S2MU005_REG_MUIC_CTRL3,
+ S2MU005_MUIC_ONESHOT_ADC);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to enable ADC oneshot mode\n");
+ return ret;
+ }
+
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_MUIC_SWCTRL, ~0);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to clear switch control register\n");
+ return ret;
+ }
+
+ /* Find all set states and clear them */
+ for (i = 0; priv->extcon_cable[i]; i++) {
+ unsigned int state = priv->extcon_cable[i];
+
+ if (extcon_get_state(priv->extcon, state) == true)
+ extcon_set_state_sync(priv->extcon, state, false);
+ }
+
+ priv->attached = false;
+
+ return 0;
+}
+
+static int s2mu005_muic_attach(struct s2m_muic *priv)
+{
+ unsigned int type;
+ int ret;
+
+ /* If any device is already attached, detach it */
+ if (priv->attached) {
+ s2mu005_muic_detach(priv);
+ msleep(100);
+ }
+
+ ret = regmap_read(priv->regmap, S2MU005_REG_MUIC_DEV1, &type);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to read DEV1 register\n");
+ return ret;
+ }
+
+ /*
+ * All USB connections which require communication via its D+
+ * and D- wires need it.
+ */
+ if (type & (S2MU005_MUIC_OTG | S2MU005_MUIC_DCP | S2MU005_MUIC_SDP)) {
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_MUIC_SWCTRL,
+ S2MU005_MUIC_DM_DP,
+ FIELD_PREP(S2MU005_MUIC_DM_DP,
+ S2MU005_MUIC_DM_DP_USB));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to configure DM/DP pins\n");
+ return ret;
+ }
+ }
+
+ /*
+ * For OTG connections, enable manual switching and ADC oneshot
+ * mode. Since the port will now be supplying power, the
+ * internal ADC (measuring the ID-GND resistance) is made to
+ * poll periodically for any changes, so as to prevent any
+ * damages due to power.
+ */
+ if (type & S2MU005_MUIC_OTG) {
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_MUIC_CTRL1,
+ S2MU005_MUIC_MAN_SW);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to enable manual switching\n");
+ return ret;
+ }
+
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_MUIC_CTRL3,
+ S2MU005_MUIC_ONESHOT_ADC);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to disable ADC oneshot mode\n");
+ return ret;
+ }
+ }
+
+ switch (type) {
+ case S2MU005_MUIC_OTG:
+ dev_dbg(priv->dev, "USB OTG connection detected\n");
+ extcon_set_state_sync(priv->extcon, EXTCON_USB_HOST, true);
+ priv->attached = true;
+ break;
+ case S2MU005_MUIC_CDP:
+ dev_dbg(priv->dev, "USB CDP connection detected\n");
+ extcon_set_state_sync(priv->extcon, EXTCON_USB, true);
+ extcon_set_state_sync(priv->extcon, EXTCON_CHG_USB_CDP, true);
+ priv->attached = true;
+ break;
+ case S2MU005_MUIC_SDP:
+ dev_dbg(priv->dev, "USB SDP connection detected\n");
+ extcon_set_state_sync(priv->extcon, EXTCON_USB, true);
+ extcon_set_state_sync(priv->extcon, EXTCON_CHG_USB_SDP, true);
+ priv->attached = true;
+ break;
+ case S2MU005_MUIC_DCP:
+ dev_dbg(priv->dev, "USB DCP connection detected\n");
+ extcon_set_state_sync(priv->extcon, EXTCON_USB, true);
+ extcon_set_state_sync(priv->extcon, EXTCON_CHG_USB_DCP, true);
+ priv->attached = true;
+ break;
+ case S2MU005_MUIC_UART:
+ dev_dbg(priv->dev, "UART connection detected\n");
+ extcon_set_state_sync(priv->extcon, EXTCON_JIG, true);
+ priv->attached = true;
+ break;
+ }
+
+ if (!priv->attached)
+ dev_warn(priv->dev, "failed to recognize the device attached\n");
+
+ return ret;
+}
+
+static int s2mu005_muic_init(struct s2m_muic *priv)
+{
+ int ret = 0;
+
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_MUIC_LDOADC_L,
+ S2MU005_MUIC_VSET,
+ FIELD_PREP(S2MU005_MUIC_VSET,
+ S2MU005_MUIC_VSET_3P0V));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set internal ADC voltage regulator\n");
+ return ret;
+ }
+
+ ret = regmap_update_bits(priv->regmap, S2MU005_REG_MUIC_LDOADC_H,
+ S2MU005_MUIC_VSET,
+ FIELD_PREP(S2MU005_MUIC_VSET,
+ S2MU005_MUIC_VSET_3P0V));
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to set internal ADC voltage regulator\n");
+ return ret;
+ }
+
+ ret = regmap_clear_bits(priv->regmap, S2MU005_REG_MUIC_CTRL1,
+ S2MU005_MUIC_IRQ);
+ if (ret < 0) {
+ dev_err(priv->dev, "failed to enable MUIC interrupts\n");
+ return ret;
+ }
+
+ return s2mu005_muic_attach(priv);
+}
+
+static const unsigned int s2mu005_muic_extcon_cable[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_CHG_USB_SDP,
+ EXTCON_CHG_USB_DCP,
+ EXTCON_CHG_USB_CDP,
+ EXTCON_JIG,
+ EXTCON_NONE,
+};
+
+static struct s2m_muic_irq_data s2mu005_muic_irq_data[] = {
+ {
+ .name = "attach",
+ .handler = s2mu005_muic_attach
+ }, {
+ .name = "detach",
+ .handler = s2mu005_muic_detach
+ }, {
+ /* sentinel */
+ }
+};
+
+static irqreturn_t s2m_muic_irq_func(int virq, void *data)
+{
+ struct s2m_muic *priv = data;
+ const struct s2m_muic_irq_data *irq_data = priv->irq_data;
+ int ret;
+ int i;
+
+ for (i = 0; irq_data[i].handler; i++) {
+ if (virq != irq_data[i].irq)
+ continue;
+
+ ret = irq_data[i].handler(priv);
+ if (ret < 0)
+ dev_err(priv->dev, "failed to handle interrupt for %s (%d)\n",
+ irq_data[i].name, ret);
+ break;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int s2m_muic_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sec_pmic_dev *pmic_drvdata = dev_get_drvdata(dev->parent);
+ struct s2m_muic *priv;
+ int ret;
+ int i;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+ priv->dev = dev;
+ priv->regmap = pmic_drvdata->regmap_pmic;
+
+ switch (platform_get_device_id(pdev)->driver_data) {
+ case S2MU005:
+ priv->extcon_cable = s2mu005_muic_extcon_cable;
+ priv->irq_data = s2mu005_muic_irq_data;
+ /* Initialize MUIC */
+ ret = s2mu005_muic_init(priv);
+ break;
+ default:
+ return dev_err_probe(dev, -ENODEV,
+ "device type %d is not supported by driver\n",
+ pmic_drvdata->device_type);
+ }
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to initialize MUIC\n");
+
+ priv->extcon = devm_extcon_dev_allocate(dev, priv->extcon_cable);
+ if (IS_ERR(priv->extcon))
+ return dev_err_probe(dev, PTR_ERR(priv->extcon),
+ "failed to allocate memory for extcon\n");
+
+ ret = devm_extcon_dev_register(dev, priv->extcon);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to register extcon device\n");
+
+ for (i = 0; priv->irq_data[i].handler; i++) {
+ int irq = platform_get_irq_byname_optional(pdev,
+ priv->irq_data[i].name);
+ if (irq == -ENXIO)
+ continue;
+ if (irq <= 0)
+ return dev_err_probe(dev, -EINVAL, "failed to get IRQ %s\n",
+ priv->irq_data[i].name);
+
+ priv->irq_data[i].irq = irq;
+ ret = devm_request_threaded_irq(dev, irq, NULL,
+ s2m_muic_irq_func, IRQF_ONESHOT,
+ priv->irq_data[i].name, priv);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to request IRQ\n");
+ }
+
+ return 0;
+}
+
+static void s2m_muic_remove(struct platform_device *pdev)
+{
+ struct s2m_muic *priv = dev_get_drvdata(&pdev->dev);
+
+ /*
+ * Disabling the MUIC device is important as it disables manual
+ * switching mode, thereby enabling auto switching mode.
+ *
+ * This is to ensure that when the board is powered off, it
+ * goes into LPM charging mode when a USB charger is connected.
+ */
+ switch (platform_get_device_id(pdev)->driver_data) {
+ case S2MU005:
+ s2mu005_muic_detach(priv);
+ break;
+ }
+}
+
+static const struct platform_device_id s2m_muic_id_table[] = {
+ { "s2mu005-muic", S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, s2m_muic_id_table);
+
+static const struct of_device_id s2m_muic_of_match_table[] = {
+ {
+ .compatible = "samsung,s2mu005-muic",
+ .data = (void *)S2MU005,
+ }, {
+ /* sentinel */
+ },
+};
+MODULE_DEVICE_TABLE(of, s2m_muic_of_match_table);
+
+static struct platform_driver s2m_muic_driver = {
+ .driver = {
+ .name = "s2m-muic",
+ },
+ .probe = s2m_muic_probe,
+ .remove = s2m_muic_remove,
+ .id_table = s2m_muic_id_table,
+};
+module_platform_driver(s2m_muic_driver);
+
+MODULE_DESCRIPTION("Extcon Driver For Samsung S2M Series PMICs");
+MODULE_AUTHOR("Kaustabh Chakraborty <kauschluss@disroot.org>");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related
* [PATCH v6 09/11] Documentation: leds: document pattern behavior of Samsung S2M series PMIC RGB LEDs
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Add documentation to describe how hardware patterns (as defined by the
documentation of led-class-multicolor) are parsed and implemented by the
Samsung S2M series PMIC RGB LED driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
Documentation/leds/index.rst | 1 +
Documentation/leds/leds-s2m-rgb.rst | 60 +++++++++++++++++++++++++++++++++++++
2 files changed, 61 insertions(+)
diff --git a/Documentation/leds/index.rst b/Documentation/leds/index.rst
index bebf440042787..23fa9ff7aaf4b 100644
--- a/Documentation/leds/index.rst
+++ b/Documentation/leds/index.rst
@@ -28,6 +28,7 @@ LEDs
leds-lp5812
leds-mlxcpld
leds-mt6370-rgb
+ leds-s2m-rgb
leds-sc27xx
leds-st1202
leds-qcom-lpg
diff --git a/Documentation/leds/leds-s2m-rgb.rst b/Documentation/leds/leds-s2m-rgb.rst
new file mode 100644
index 0000000000000..4f89a8c89ea86
--- /dev/null
+++ b/Documentation/leds/leds-s2m-rgb.rst
@@ -0,0 +1,60 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+======================================
+Samsung S2M Series PMIC RGB LED Driver
+======================================
+
+Description
+-----------
+
+The RGB LED on the S2M series PMIC hardware features a three-channel LED that
+is grouped together as a single device. Furthermore, it supports 8-bit
+brightness control for each channel. This LED is typically used as a status
+indicator in mobile devices. It also supports various parameters for hardware
+patterns.
+
+The hardware pattern can be programmed using the "pattern" trigger, using the
+hw_pattern attribute.
+
+/sys/class/leds/<led>/repeat
+----------------------------
+
+The hardware supports only indefinitely repeating patterns. The repeat
+attribute must be set to -1 for hardware patterns to function.
+
+/sys/class/leds/<led>/hw_pattern
+--------------------------------
+
+Specify a hardware pattern for the RGB LEDs.
+
+The pattern is a series of brightness levels and durations in milliseconds.
+There should be only one non-zero brightness level. Unlike the results
+described in leds-trigger-pattern, the transitions between on and off states
+are smoothed out by the hardware.
+
+Simple pattern::
+
+ "255 3000 0 1000"
+
+ 255 -+ ''''''-. .-'''''''-.
+ | '. .' '.
+ | \ / \
+ | '. .' '.
+ | '-.......-' '-
+ 0 -+-------+-------+-------+-------+-------+-------+--> time (s)
+ 0 1 2 3 4 5 6
+
+As described in leds-trigger-pattern, it is also possible to use zero-length
+entries to disable the ramping mechanism.
+
+On-Off pattern::
+
+ "255 1000 255 0 0 1000 0 0"
+
+ 255 -+ ------+ +-------+ +-------+
+ | | | | | |
+ | | | | | |
+ | | | | | |
+ | +-------+ +-------+ +-------
+ 0 -+-------+-------+-------+-------+-------+-------+--> time (s)
+ 0 1 2 3 4 5 6
--
2.53.0
^ permalink raw reply related
* [PATCH v6 08/11] leds: rgb: add support for Samsung S2M series PMIC RGB LED device
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Add support for the RGB LEDs found in certain Samsung S2M series PMICs.
The device has three LED channels, controlled as a single device. These
LEDs are typically used as status indicators in mobile phones.
The driver includes initial support for the S2MU005 PMIC RGB LEDs.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/leds/rgb/Kconfig | 11 ++
drivers/leds/rgb/Makefile | 1 +
drivers/leds/rgb/leds-s2m-rgb.c | 416 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 428 insertions(+)
diff --git a/drivers/leds/rgb/Kconfig b/drivers/leds/rgb/Kconfig
index 28ef4c487367c..cf57d85e574ec 100644
--- a/drivers/leds/rgb/Kconfig
+++ b/drivers/leds/rgb/Kconfig
@@ -75,6 +75,17 @@ config LEDS_QCOM_LPG
If compiled as a module, the module will be named leds-qcom-lpg.
+config LEDS_S2M_RGB
+ tristate "Samsung S2M series PMICs RGB LED support"
+ depends on LEDS_CLASS
+ depends on MFD_SEC_CORE
+ select REGMAP_IRQ
+ help
+ This option enables support for the S2MU005 RGB LEDs. These devices
+ have three LED channels, with 8-bit brightness control for each
+ channel. The S2MU005 usually found in mobile phones as status
+ indicators.
+
config LEDS_MT6370_RGB
tristate "LED Support for MediaTek MT6370 PMIC"
depends on MFD_MT6370
diff --git a/drivers/leds/rgb/Makefile b/drivers/leds/rgb/Makefile
index be45991f63f50..98050e1aa4255 100644
--- a/drivers/leds/rgb/Makefile
+++ b/drivers/leds/rgb/Makefile
@@ -6,4 +6,5 @@ obj-$(CONFIG_LEDS_LP5812) += leds-lp5812.o
obj-$(CONFIG_LEDS_NCP5623) += leds-ncp5623.o
obj-$(CONFIG_LEDS_PWM_MULTICOLOR) += leds-pwm-multicolor.o
obj-$(CONFIG_LEDS_QCOM_LPG) += leds-qcom-lpg.o
+obj-$(CONFIG_LEDS_S2M_RGB) += leds-s2m-rgb.o
obj-$(CONFIG_LEDS_MT6370_RGB) += leds-mt6370-rgb.o
diff --git a/drivers/leds/rgb/leds-s2m-rgb.c b/drivers/leds/rgb/leds-s2m-rgb.c
new file mode 100644
index 0000000000000..e7295d0b150da
--- /dev/null
+++ b/drivers/leds/rgb/leds-s2m-rgb.c
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * RGB LED Driver for Samsung S2M series PMICs.
+ *
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (c) 2026 Kaustabh Chakraborty <kauschluss@disroot.org>
+ */
+
+#include <linux/container_of.h>
+#include <linux/led-class-multicolor.h>
+#include <linux/mfd/samsung/core.h>
+#include <linux/mfd/samsung/s2mu005.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+struct s2m_rgb {
+ struct device *dev;
+ struct regmap *regmap;
+ struct led_classdev_mc mc;
+ /*
+ * The mutex object prevents race conditions when evaluation and
+ * application of LED pattern state.
+ */
+ struct mutex lock;
+ /*
+ * State variables representing the current LED pattern, these only to
+ * be accessed when lock is held.
+ */
+ u8 ramp_up;
+ u8 ramp_dn;
+ u8 stay_hi;
+ u8 stay_lo;
+};
+
+static struct led_classdev_mc *to_s2m_mc(struct led_classdev *cdev)
+{
+ return container_of(cdev, struct led_classdev_mc, led_cdev);
+}
+
+static struct s2m_rgb *to_s2m_rgb(struct led_classdev_mc *mc)
+{
+ return container_of(mc, struct s2m_rgb, mc);
+}
+
+static const u32 s2mu005_rgb_lut_ramp[] = {
+ 0, 100, 200, 300, 400, 500, 600, 700,
+ 800, 1000, 1200, 1400, 1600, 1800, 2000, 2200,
+};
+
+static const u32 s2mu005_rgb_lut_stay_hi[] = {
+ 100, 200, 300, 400, 500, 750, 1000, 1250,
+ 1500, 1750, 2000, 2250, 2500, 2750, 3000, 3250,
+};
+
+static const u32 s2mu005_rgb_lut_stay_lo[] = {
+ 0, 500, 1000, 1500, 2000, 2500, 3000, 3500,
+ 4000, 4500, 5000, 6000, 7000, 8000, 10000, 12000,
+};
+
+static int s2mu005_rgb_apply_params(struct s2m_rgb *rgb)
+{
+ struct regmap *regmap = rgb->regmap;
+ unsigned int ramp_val = 0;
+ unsigned int stay_val = 0;
+ int ret;
+
+ ramp_val |= FIELD_PREP(S2MU005_RGB_CH_RAMP_UP, rgb->ramp_up);
+ ramp_val |= FIELD_PREP(S2MU005_RGB_CH_RAMP_DN, rgb->ramp_dn);
+
+ stay_val |= FIELD_PREP(S2MU005_RGB_CH_STAY_HI, rgb->stay_hi);
+ stay_val |= FIELD_PREP(S2MU005_RGB_CH_STAY_LO, rgb->stay_lo);
+
+ ret = regmap_write(regmap, S2MU005_REG_RGB_EN, S2MU005_RGB_RESET);
+ if (ret) {
+ dev_err(rgb->dev, "failed to reset RGB LEDs\n");
+ return ret;
+ }
+
+ for (int i = 0; i < rgb->mc.num_colors; i++) {
+ ret = regmap_write(regmap, S2MU005_REG_RGB_CH_CTRL(i),
+ rgb->mc.subled_info[i].brightness);
+ if (ret) {
+ dev_err(rgb->dev, "failed to set LED brightness\n");
+ return ret;
+ }
+
+ ret = regmap_write(regmap, S2MU005_REG_RGB_CH_RAMP(i), ramp_val);
+ if (ret) {
+ dev_err(rgb->dev, "failed to set ramp timings\n");
+ return ret;
+ }
+
+ ret = regmap_write(regmap, S2MU005_REG_RGB_CH_STAY(i), stay_val);
+ if (ret) {
+ dev_err(rgb->dev, "failed to set stay timings\n");
+ return ret;
+ }
+ }
+
+ ret = regmap_update_bits(regmap, S2MU005_REG_RGB_EN, S2MU005_RGB_SLOPE,
+ S2MU005_RGB_SLOPE_SMOOTH);
+ if (ret) {
+ dev_err(rgb->dev, "failed to set ramp slope\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int s2mu005_rgb_reset_params(struct s2m_rgb *rgb)
+{
+ struct regmap *regmap = rgb->regmap;
+ int ret;
+
+ ret = regmap_write(regmap, S2MU005_REG_RGB_EN, S2MU005_RGB_RESET);
+ if (ret) {
+ dev_err(rgb->dev, "failed to reset RGB LEDs\n");
+ return ret;
+ }
+
+ rgb->ramp_up = 0;
+ rgb->ramp_dn = 0;
+ rgb->stay_hi = 0;
+ rgb->stay_lo = 0;
+
+ return 0;
+}
+
+/*
+ * s2m_rgb_lut_get_closest_duration - find closest duration in look-up table
+ * @lut: the look-up table to search for the closest timing
+ * @len: number of elements in the look-up table array
+ * @duration: the timing duration requested
+ *
+ * This function does a binary search on the given array, and finds the closest
+ * value to the requested timing. It is expected that the look-up table to be
+ * provided, is already sorted.
+ *
+ * This function returns a negative error code, or a non-negative index of the
+ * value in the look-up table closest to the one requested.
+ */
+static int s2m_rgb_lut_get_closest_duration(const u32 *lut, const size_t len, const u32 duration)
+{
+ u32 closest_distance = abs(duration - lut[0]);
+ int closest_index = 0;
+ int lo = 0;
+ int hi = len - 1;
+
+ /* Bounds checking */
+ if (duration < lut[0] || duration > lut[len - 1])
+ return -EINVAL;
+
+ while (lo <= hi) {
+ int mid = lo + (hi - lo) / 2;
+
+ /* Narrow down search window as per binary-search algorithm. */
+ if (duration < lut[mid])
+ hi = mid - 1;
+ else
+ lo = mid + 1;
+
+ if (abs(duration - lut[mid]) < closest_distance) {
+ closest_distance = abs(duration - lut[mid]);
+ closest_index = mid;
+ }
+ }
+
+ return closest_index;
+}
+
+static int s2m_rgb_pattern_set(struct led_classdev *cdev, struct led_pattern *pattern, u32 len,
+ int repeat)
+{
+ struct s2m_rgb *rgb = to_s2m_rgb(to_s2m_mc(cdev));
+ const u32 *lut_ramp_up, *lut_ramp_dn, *lut_stay_hi, *lut_stay_lo;
+ size_t lut_ramp_up_len, lut_ramp_dn_len, lut_stay_hi_len, lut_stay_lo_len;
+ int brightness_peak = 0;
+ u32 time_hi = 0, time_lo = 0;
+ bool ramp_up_en, ramp_dn_en;
+ int ret;
+
+ /*
+ * The typical pattern supported by this device can be represented with
+ * the following graph:
+ *
+ * 255 T ''''''-. .-'''''''-.
+ * | '. .' '.
+ * | \ / \
+ * | '. .' '.
+ * | '-...........-' '-
+ * 0 +----------------------------------------------------> time (s)
+ *
+ * <---- HIGH ----><-- LOW --><-------- HIGH --------->
+ * <-----><-------><---------><-------><-----><------->
+ * stay_hi ramp_dn stay_lo ramp_up stay_hi ramp_dn
+ *
+ * There are two states, named HIGH and LOW. HIGH has a non-zero
+ * brightness level, while LOW is of zero brightness. The pattern
+ * provided should mention only one zero and non-zero brightness level.
+ * The hardware always starts the pattern from the HIGH state, as shown
+ * in the graph.
+ *
+ * The HIGH state can be divided in three somewhat equal timings:
+ * ramp_up, stay_hi, and ramp_dn. The LOW state has only one timing:
+ * stay_lo.
+ */
+
+ /* Only indefinitely looping patterns are supported. */
+ if (repeat != -1)
+ return -EINVAL;
+
+ /* Pattern should consist of at least two tuples. */
+ if (len < 2)
+ return -EINVAL;
+
+ for (int i = 0; i < len; i++) {
+ int brightness = pattern[i].brightness;
+ u32 delta_t = pattern[i].delta_t;
+
+ if (brightness) {
+ /*
+ * The pattern shold define only one non-zero
+ * brightness in the HIGH state. The device doesn't
+ * have any provisions to handle multiple peak
+ * brightness levels.
+ */
+ if (brightness_peak && brightness_peak != brightness)
+ return -EINVAL;
+
+ brightness_peak = brightness;
+ time_hi += delta_t;
+ ramp_dn_en = !!delta_t;
+ } else {
+ time_lo += delta_t;
+ ramp_up_en = !!delta_t;
+ }
+ }
+
+ /* LUTs are specific to device variant. */
+ lut_ramp_up = s2mu005_rgb_lut_ramp;
+ lut_ramp_up_len = ARRAY_SIZE(s2mu005_rgb_lut_ramp);
+ lut_ramp_dn = s2mu005_rgb_lut_ramp;
+ lut_ramp_dn_len = ARRAY_SIZE(s2mu005_rgb_lut_ramp);
+ lut_stay_hi = s2mu005_rgb_lut_stay_hi;
+ lut_stay_hi_len = ARRAY_SIZE(s2mu005_rgb_lut_stay_hi);
+ lut_stay_lo = s2mu005_rgb_lut_stay_lo;
+ lut_stay_lo_len = ARRAY_SIZE(s2mu005_rgb_lut_stay_lo);
+
+ mutex_lock(&rgb->lock);
+
+ /*
+ * The timings ramp_up, stay_hi, and ramp_dn of the HIGH state are
+ * roughly equal. Firstly, calculate and set timings for ramp_up and
+ * ramp_dn (making sure they're exactly equal).
+ */
+ rgb->ramp_up = 0;
+ rgb->ramp_dn = 0;
+
+ if (ramp_up_en) {
+ ret = s2m_rgb_lut_get_closest_duration(lut_ramp_up, lut_ramp_up_len, time_hi / 3);
+ if (ret < 0)
+ goto param_fail;
+ rgb->ramp_up = (u8)ret;
+ }
+
+ if (ramp_dn_en) {
+ ret = s2m_rgb_lut_get_closest_duration(lut_ramp_dn, lut_ramp_dn_len, time_hi / 3);
+ if (ret < 0)
+ goto param_fail;
+ rgb->ramp_dn = (u8)ret;
+ }
+
+ /*
+ * Subtract the allocated ramp timings from time_hi (and also making
+ * sure it doesn't underflow!). The remaining time is allocated to
+ * stay_hi.
+ */
+ time_hi -= min(time_hi, lut_ramp_up[rgb->ramp_up]);
+ time_hi -= min(time_hi, lut_ramp_dn[rgb->ramp_dn]);
+
+ ret = s2m_rgb_lut_get_closest_duration(lut_stay_hi, lut_stay_hi_len, time_hi);
+ if (ret < 0)
+ goto param_fail;
+ rgb->stay_hi = (u8)ret;
+
+ ret = s2m_rgb_lut_get_closest_duration(lut_stay_lo, lut_stay_lo_len, time_lo);
+ if (ret < 0)
+ goto param_fail;
+ rgb->stay_lo = (u8)ret;
+
+ led_mc_calc_color_components(&rgb->mc, brightness_peak);
+ /* Apply params with variant-specific implementation. */
+ ret = s2mu005_rgb_apply_params(rgb);
+ if (ret)
+ goto param_fail;
+
+ mutex_unlock(&rgb->lock);
+
+ return 0;
+
+param_fail:
+ rgb->ramp_up = 0;
+ rgb->ramp_dn = 0;
+ rgb->stay_hi = 0;
+ rgb->stay_lo = 0;
+
+ mutex_unlock(&rgb->lock);
+
+ return ret;
+}
+
+static int s2m_rgb_pattern_clear(struct led_classdev *cdev)
+{
+ struct s2m_rgb *rgb = to_s2m_rgb(to_s2m_mc(cdev));
+ int ret = 0;
+
+ mutex_lock(&rgb->lock);
+
+ /* Reset params with variant-specific implementation. */
+ ret = s2mu005_rgb_reset_params(rgb);
+
+ mutex_unlock(&rgb->lock);
+
+ return ret;
+}
+
+static int s2m_rgb_brightness_set(struct led_classdev *cdev, enum led_brightness value)
+{
+ struct s2m_rgb *rgb = to_s2m_rgb(to_s2m_mc(cdev));
+ int ret = 0;
+
+ if (!value)
+ return s2m_rgb_pattern_clear(cdev);
+
+ mutex_lock(&rgb->lock);
+
+ led_mc_calc_color_components(&rgb->mc, value);
+ /* Apply params with variant-specific implementation. */
+ ret = s2mu005_rgb_apply_params(rgb);
+
+ mutex_unlock(&rgb->lock);
+
+ return ret;
+}
+
+static struct mc_subled s2mu005_rgb_subled_info[] = {
+ { .channel = 0, .color_index = LED_COLOR_ID_BLUE },
+ { .channel = 1, .color_index = LED_COLOR_ID_GREEN },
+ { .channel = 2, .color_index = LED_COLOR_ID_RED },
+};
+
+static int s2m_rgb_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sec_pmic_dev *pmic_drvdata = dev_get_drvdata(dev->parent);
+ struct s2m_rgb *rgb;
+ struct led_init_data init_data = {};
+ int ret;
+
+ rgb = devm_kzalloc(dev, sizeof(*rgb), GFP_KERNEL);
+ if (!rgb)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, rgb);
+ rgb->dev = dev;
+ rgb->regmap = pmic_drvdata->regmap_pmic;
+
+ /* Configure variant-specific details. */
+ rgb->mc.subled_info = s2mu005_rgb_subled_info;
+ rgb->mc.num_colors = ARRAY_SIZE(s2mu005_rgb_subled_info);
+
+ rgb->mc.led_cdev.max_brightness = 255;
+ rgb->mc.led_cdev.brightness_set_blocking = s2m_rgb_brightness_set;
+ rgb->mc.led_cdev.pattern_set = s2m_rgb_pattern_set;
+ rgb->mc.led_cdev.pattern_clear = s2m_rgb_pattern_clear;
+
+ ret = devm_mutex_init(dev, &rgb->lock);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to create mutex lock\n");
+
+ init_data.fwnode = of_fwnode_handle(dev->of_node);
+ ret = devm_led_classdev_multicolor_register_ext(dev, &rgb->mc, &init_data);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to create LED device\n");
+
+ return 0;
+}
+
+static const struct platform_device_id s2m_rgb_id_table[] = {
+ { "s2mu005-rgb", S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, s2m_rgb_id_table);
+
+static const struct of_device_id s2m_rgb_of_match_table[] = {
+ { .compatible = "samsung,s2mu005-rgb", .data = (void *)S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, s2m_rgb_of_match_table);
+
+static struct platform_driver s2m_rgb_driver = {
+ .driver = {
+ .name = "s2m-rgb",
+ },
+ .probe = s2m_rgb_probe,
+ .id_table = s2m_rgb_id_table,
+};
+module_platform_driver(s2m_rgb_driver);
+
+MODULE_DESCRIPTION("RGB LED Driver for Samsung S2M Series PMICs");
+MODULE_AUTHOR("Kaustabh Chakraborty <kauschluss@disroot.org>");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related
* [PATCH v6 07/11] leds: flash: add support for Samsung S2M series PMIC flash LED device
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Add support for flash LEDs found in certain Samsung S2M series PMICs.
The device has two channels for LEDs, typically for the back and front
cameras in mobile devices. Both channels can be independently
controlled, and can be operated in torch or flash modes.
The driver includes initial support for the S2MU005 PMIC flash LEDs.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/leds/flash/Kconfig | 12 ++
drivers/leds/flash/Makefile | 1 +
drivers/leds/flash/leds-s2m-flash.c | 352 ++++++++++++++++++++++++++++++++++++
3 files changed, 365 insertions(+)
diff --git a/drivers/leds/flash/Kconfig b/drivers/leds/flash/Kconfig
index 5e08102a67841..b6542ecc522dd 100644
--- a/drivers/leds/flash/Kconfig
+++ b/drivers/leds/flash/Kconfig
@@ -114,6 +114,18 @@ config LEDS_RT8515
To compile this driver as a module, choose M here: the module
will be called leds-rt8515.
+config LEDS_S2M_FLASH
+ tristate "Samsung S2M series PMICs flash/torch LED support"
+ depends on LEDS_CLASS
+ depends on MFD_SEC_CORE
+ depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
+ select REGMAP_IRQ
+ help
+ This option enables support for the flash/torch LEDs found in certain
+ Samsung S2M series PMICs, such as the S2MU005. It has a LED channel
+ dedicated for every physical LED. The LEDs can be controlled in flash
+ and torch modes.
+
config LEDS_SGM3140
tristate "LED support for the SGM3140"
depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
diff --git a/drivers/leds/flash/Makefile b/drivers/leds/flash/Makefile
index 712fb737a428e..44e6c1b4beb37 100644
--- a/drivers/leds/flash/Makefile
+++ b/drivers/leds/flash/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_LEDS_MAX77693) += leds-max77693.o
obj-$(CONFIG_LEDS_QCOM_FLASH) += leds-qcom-flash.o
obj-$(CONFIG_LEDS_RT4505) += leds-rt4505.o
obj-$(CONFIG_LEDS_RT8515) += leds-rt8515.o
+obj-$(CONFIG_LEDS_S2M_FLASH) += leds-s2m-flash.o
obj-$(CONFIG_LEDS_SGM3140) += leds-sgm3140.o
obj-$(CONFIG_LEDS_SY7802) += leds-sy7802.o
obj-$(CONFIG_LEDS_TPS6131X) += leds-tps6131x.o
diff --git a/drivers/leds/flash/leds-s2m-flash.c b/drivers/leds/flash/leds-s2m-flash.c
new file mode 100644
index 0000000000000..40cc5f8b8adc9
--- /dev/null
+++ b/drivers/leds/flash/leds-s2m-flash.c
@@ -0,0 +1,352 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Flash and Torch LED Driver for Samsung S2M series PMICs.
+ *
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (c) 2026 Kaustabh Chakraborty <kauschluss@disroot.org>
+ */
+
+#include <linux/container_of.h>
+#include <linux/led-class-flash.h>
+#include <linux/mfd/samsung/core.h>
+#include <linux/mfd/samsung/s2mu005.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <media/v4l2-flash-led-class.h>
+
+#define MAX_CHANNELS 2
+
+struct s2m_led {
+ struct regmap *regmap;
+ struct led_classdev_flash fled;
+ struct v4l2_flash *v4l2_flash;
+ /*
+ * The mutex object prevents the concurrent access of flash control
+ * registers by the LED and V4L2 subsystems.
+ */
+ struct mutex lock;
+ unsigned int reg_enable;
+ u8 channel;
+ u8 flash_brightness;
+ u8 flash_timeout;
+};
+
+static struct s2m_led *to_s2m_led(struct led_classdev_flash *fled)
+{
+ return container_of(fled, struct s2m_led, fled);
+}
+
+static struct led_classdev_flash *to_s2m_fled(struct led_classdev *cdev)
+{
+ return container_of(cdev, struct led_classdev_flash, led_cdev);
+}
+
+static int s2m_fled_flash_brightness_set(struct led_classdev_flash *fled, u32 brightness)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ struct led_flash_setting *setting = &fled->brightness;
+
+ led->flash_brightness = (brightness - setting->min) / setting->step;
+
+ return 0;
+}
+
+static int s2m_fled_flash_timeout_set(struct led_classdev_flash *fled, u32 timeout)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ struct led_flash_setting *setting = &fled->timeout;
+
+ led->flash_timeout = (timeout - setting->min) / setting->step;
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_V4L2_FLASH_LED_CLASS)
+static int s2m_fled_flash_external_strobe_set(struct v4l2_flash *v4l2_flash, bool enable)
+{
+ struct s2m_led *led = to_s2m_led(v4l2_flash->fled_cdev);
+
+ mutex_lock(&led->lock);
+
+ led->fled.ops->strobe_set(&led->fled, enable);
+
+ mutex_unlock(&led->lock);
+
+ return 0;
+}
+
+static const struct v4l2_flash_ops s2m_fled_v4l2_flash_ops = {
+ .external_strobe_set = s2m_fled_flash_external_strobe_set,
+};
+#else
+static const struct v4l2_flash_ops s2m_fled_v4l2_flash_ops;
+#endif
+
+static void s2m_fled_v4l2_flash_release(void *v4l2_flash)
+{
+ v4l2_flash_release(v4l2_flash);
+}
+
+static int s2mu005_fled_torch_brightness_set(struct led_classdev *cdev, enum led_brightness value)
+{
+ struct s2m_led *led = to_s2m_led(to_s2m_fled(cdev));
+ int ret;
+
+ mutex_lock(&led->lock);
+
+ if (!value) {
+ ret = regmap_clear_bits(led->regmap, led->reg_enable,
+ S2MU005_FLED_TORCH_EN(led->channel));
+ if (ret)
+ dev_err(cdev->dev, "failed to disable torch LED\n");
+ goto unlock;
+ }
+
+ ret = regmap_update_bits(led->regmap, S2MU005_REG_FLED_CH_CTRL1(led->channel),
+ S2MU005_FLED_TORCH_IOUT,
+ FIELD_PREP(S2MU005_FLED_TORCH_IOUT, value - 1));
+ if (ret) {
+ dev_err(cdev->dev, "failed to set torch current\n");
+ goto unlock;
+ }
+
+ ret = regmap_set_bits(led->regmap, led->reg_enable, S2MU005_FLED_TORCH_EN(led->channel));
+ if (ret) {
+ dev_err(cdev->dev, "failed to enable torch LED\n");
+ goto unlock;
+ }
+
+unlock:
+ mutex_unlock(&led->lock);
+
+ return ret;
+}
+
+static int s2mu005_fled_flash_strobe_set(struct led_classdev_flash *fled, bool state)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ int ret;
+
+ mutex_lock(&led->lock);
+
+ ret = regmap_clear_bits(led->regmap, led->reg_enable, S2MU005_FLED_FLASH_EN(led->channel));
+ if (ret) {
+ dev_err(fled->led_cdev.dev, "failed to disable flash LED\n");
+ goto unlock;
+ }
+
+ if (!state)
+ goto unlock;
+
+ ret = regmap_update_bits(led->regmap, S2MU005_REG_FLED_CH_CTRL0(led->channel),
+ S2MU005_FLED_FLASH_IOUT,
+ FIELD_PREP(S2MU005_FLED_FLASH_IOUT, led->flash_brightness));
+ if (ret) {
+ dev_err(fled->led_cdev.dev, "failed to set flash brightness\n");
+ goto unlock;
+ }
+
+ ret = regmap_update_bits(led->regmap, S2MU005_REG_FLED_CH_CTRL3(led->channel),
+ S2MU005_FLED_FLASH_TIMEOUT,
+ FIELD_PREP(S2MU005_FLED_FLASH_TIMEOUT, led->flash_timeout));
+ if (ret) {
+ dev_err(fled->led_cdev.dev, "failed to set flash timeout\n");
+ goto unlock;
+ }
+
+ ret = regmap_set_bits(led->regmap, led->reg_enable, S2MU005_FLED_FLASH_EN(led->channel));
+ if (ret) {
+ dev_err(fled->led_cdev.dev, "failed to enable flash LED\n");
+ goto unlock;
+ }
+
+unlock:
+ mutex_unlock(&led->lock);
+
+ return ret;
+}
+
+static int s2mu005_fled_flash_strobe_get(struct led_classdev_flash *fled, bool *state)
+{
+ struct s2m_led *led = to_s2m_led(fled);
+ u32 val;
+ int ret;
+
+ mutex_lock(&led->lock);
+
+ ret = regmap_read(led->regmap, S2MU005_REG_FLED_STATUS, &val);
+ if (ret) {
+ dev_err(fled->led_cdev.dev, "failed to fetch LED status\n");
+ goto unlock;
+ }
+
+ *state = !!(val & S2MU005_FLED_FLASH_STATUS(led->channel));
+
+unlock:
+ mutex_unlock(&led->lock);
+
+ return ret;
+}
+
+static const struct led_flash_ops s2mu005_fled_flash_ops = {
+ .flash_brightness_set = s2m_fled_flash_brightness_set,
+ .timeout_set = s2m_fled_flash_timeout_set,
+ .strobe_set = s2mu005_fled_flash_strobe_set,
+ .strobe_get = s2mu005_fled_flash_strobe_get,
+};
+
+static int s2mu005_fled_init(struct s2m_led *led, struct device *dev, struct regmap *regmap,
+ unsigned int nr_channels)
+{
+ unsigned int val;
+ int ret;
+
+ /* Enable the LED channels. */
+ ret = regmap_set_bits(regmap, S2MU005_REG_FLED_CTRL1, S2MU005_FLED_CH_EN);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to enable LED channels\n");
+
+ ret = regmap_read(regmap, S2MU005_REG_ID, &val);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to read revision\n");
+
+ for (int i = 0; i < nr_channels; i++) {
+ /*
+ * Read the revision register. Revision EVT0 has the register
+ * at CTRL4, while EVT1 and higher have it at CTRL6.
+ */
+ if (FIELD_GET(S2MU005_ID_MASK, val) == 0)
+ led[i].reg_enable = S2MU005_REG_FLED_CTRL4;
+ else
+ led[i].reg_enable = S2MU005_REG_FLED_CTRL6;
+ }
+
+ return 0;
+}
+
+static int s2mu005_fled_init_channel(struct s2m_led *led, struct device *dev,
+ struct fwnode_handle *fwnp)
+{
+ struct led_classdev *cdev = &led->fled.led_cdev;
+ struct led_init_data init_data = {};
+ struct v4l2_flash_config v4l2_cfg = {};
+ int ret;
+
+ cdev->max_brightness = 16;
+ cdev->brightness_set_blocking = s2mu005_fled_torch_brightness_set;
+ cdev->flags |= LED_DEV_CAP_FLASH;
+
+ led->fled.timeout.min = 62000;
+ led->fled.timeout.step = 62000;
+ led->fled.timeout.max = 992000;
+ led->fled.timeout.val = 992000;
+
+ led->fled.brightness.min = 25000;
+ led->fled.brightness.step = 25000;
+ led->fled.brightness.max = 375000; /* 400000 causes flickering */
+ led->fled.brightness.val = 375000;
+
+ s2m_fled_flash_timeout_set(&led->fled, led->fled.timeout.val);
+ s2m_fled_flash_brightness_set(&led->fled, led->fled.brightness.val);
+
+ led->fled.ops = &s2mu005_fled_flash_ops;
+
+ init_data.fwnode = fwnp;
+ ret = devm_led_classdev_flash_register_ext(dev, &led->fled, &init_data);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to create LED flash device\n");
+
+ v4l2_cfg.intensity.min = led->fled.brightness.min;
+ v4l2_cfg.intensity.step = led->fled.brightness.step;
+ v4l2_cfg.intensity.max = led->fled.brightness.max;
+ v4l2_cfg.intensity.val = led->fled.brightness.val;
+
+ v4l2_cfg.has_external_strobe = true;
+
+ led->v4l2_flash = v4l2_flash_init(dev, fwnp, &led->fled, &s2m_fled_v4l2_flash_ops,
+ &v4l2_cfg);
+ if (IS_ERR(led->v4l2_flash))
+ return dev_err_probe(dev, PTR_ERR(led->v4l2_flash),
+ "failed to create V4L2 flash device\n");
+
+ ret = devm_add_action_or_reset(dev, (void *)s2m_fled_v4l2_flash_release, led->v4l2_flash);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to add cleanup action\n");
+
+ return 0;
+}
+
+static int s2m_fled_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sec_pmic_dev *ddata = dev_get_drvdata(dev->parent);
+ struct s2m_led *led;
+ int ret;
+
+ led = devm_kzalloc(dev, sizeof(*led) * MAX_CHANNELS, GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ /* Initialize LED controller with variant-specific implementation. */
+ ret = s2mu005_fled_init(led, dev, ddata->regmap_pmic, MAX_CHANNELS);
+ if (ret)
+ return ret;
+
+ device_for_each_child_node_scoped(dev, child) {
+ u32 reg;
+
+ if (fwnode_property_read_u32(child, "reg", ®))
+ continue;
+
+ if (reg >= MAX_CHANNELS) {
+ dev_warn(dev, "channel %d is non-existent\n", reg);
+ continue;
+ }
+
+ if (led[reg].regmap) {
+ dev_warn(dev, "duplicate node for channel %d\n", reg);
+ continue;
+ }
+
+ led[reg].regmap = ddata->regmap_pmic;
+ led[reg].channel = (u8)reg;
+
+ ret = devm_mutex_init(dev, &led[reg].lock);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to create mutex\n");
+
+ /* Initialize LED channel with variant-specific implementation. */
+ ret = s2mu005_fled_init_channel(led + reg, dev, child);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id s2m_fled_id_table[] = {
+ { "s2mu005-flash", S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, s2m_fled_id_table);
+
+static const struct of_device_id s2m_fled_of_match_table[] = {
+ { .compatible = "samsung,s2mu005-flash", .data = (void *)S2MU005 },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, s2m_fled_of_match_table);
+
+static struct platform_driver s2m_fled_driver = {
+ .driver = {
+ .name = "s2m-flash",
+ },
+ .probe = s2m_fled_probe,
+ .id_table = s2m_fled_id_table,
+};
+module_platform_driver(s2m_fled_driver);
+
+MODULE_DESCRIPTION("Flash/Torch LED Driver for Samsung S2M Series PMICs");
+MODULE_AUTHOR("Kaustabh Chakraborty <kauschluss@disroot.org>");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related
* [PATCH v6 06/11] mfd: sec: resolve PMIC revision in S2MU005
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
In devices other than S2MPG1X, the revision can be retrieved from the
first register of the PMIC regmap. In S2MU005 however, the location is
in offset 0x73. Introduce a switch-case block to allow selecting the
REG_ID register.
S2MU005 also has a field mask for the revision. Apply it using
FIELD_GET() and get the extracted value.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/mfd/sec-common.c | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
diff --git a/drivers/mfd/sec-common.c b/drivers/mfd/sec-common.c
index afc9e691bb67c..fe92bc4a3dd26 100644
--- a/drivers/mfd/sec-common.c
+++ b/drivers/mfd/sec-common.c
@@ -16,6 +16,7 @@
#include <linux/mfd/samsung/irq.h>
#include <linux/mfd/samsung/s2mps11.h>
#include <linux/mfd/samsung/s2mps13.h>
+#include <linux/mfd/samsung/s2mu005.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/pm.h>
@@ -119,20 +120,25 @@ static const struct mfd_cell s2mu005_devs[] = {
static void sec_pmic_dump_rev(struct sec_pmic_dev *sec_pmic)
{
- unsigned int val;
+ unsigned int reg, mask, val;
- /* For s2mpg1x, the revision is in a different regmap */
switch (sec_pmic->device_type) {
case S2MPG10:
case S2MPG11:
+ /* For s2mpg1x, the revision is in a different regmap */
return;
- default:
+ case S2MU005:
+ reg = S2MU005_REG_ID;
+ mask = S2MU005_ID_MASK;
break;
+ default:
+ /* For other device types, REG_ID is always the first register. */
+ reg = S2MPS11_REG_ID;
+ mask = ~0;
}
- /* For each device type, the REG_ID is always the first register */
- if (!regmap_read(sec_pmic->regmap_pmic, S2MPS11_REG_ID, &val))
- dev_dbg(sec_pmic->dev, "Revision: 0x%x\n", val);
+ if (!regmap_read(sec_pmic->regmap_pmic, reg, &val))
+ dev_dbg(sec_pmic->dev, "Revision: 0x%x\n", field_get(mask, val));
}
static void sec_pmic_configure(struct sec_pmic_dev *sec_pmic)
--
2.53.0
^ permalink raw reply related
* [PATCH v6 05/11] mfd: sec: set DMA coherent mask
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Kernel logs are filled with "DMA mask not set" messages for every
sub-device. The device does not use DMA for communication, so these
messages are useless. Disable the coherent DMA mask for the PMIC device,
which is also propagated to sub-devices.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/mfd/sec-common.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/mfd/sec-common.c b/drivers/mfd/sec-common.c
index ad1c7de83a620..afc9e691bb67c 100644
--- a/drivers/mfd/sec-common.c
+++ b/drivers/mfd/sec-common.c
@@ -215,6 +215,9 @@ int sec_pmic_probe(struct device *dev, int device_type, unsigned int irq,
if (IS_ERR(irq_data))
return PTR_ERR(irq_data);
+ dev->coherent_dma_mask = 0;
+ dev->dma_mask = &dev->coherent_dma_mask;
+
pm_runtime_set_active(sec_pmic->dev);
switch (sec_pmic->device_type) {
--
2.53.0
^ permalink raw reply related
* [PATCH v6 04/11] mfd: sec: add support for S2MU005 PMIC
From: Kaustabh Chakraborty @ 2026-05-15 10:39 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
USB Interface Controller), and flash and RGB LED controllers.
S2MU005's interrupt registers can be properly divided into three regmap
IRQ chips, one each for the charger, flash LEDs, and the MUIC.
Add initial support for S2MU005 in the PMIC driver, along with it's three
interrupt chips.
Co-developed-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Łukasz Lebiedziński <kernel@lvkasz.us>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
drivers/mfd/sec-common.c | 16 ++
drivers/mfd/sec-i2c.c | 29 ++++
drivers/mfd/sec-irq.c | 74 ++++++++
include/linux/mfd/samsung/core.h | 1 +
include/linux/mfd/samsung/irq.h | 66 +++++++
include/linux/mfd/samsung/s2mu005.h | 332 ++++++++++++++++++++++++++++++++++++
6 files changed, 518 insertions(+)
diff --git a/drivers/mfd/sec-common.c b/drivers/mfd/sec-common.c
index bd8b5f9686892..ad1c7de83a620 100644
--- a/drivers/mfd/sec-common.c
+++ b/drivers/mfd/sec-common.c
@@ -105,6 +105,18 @@ static const struct mfd_cell s2mpu05_devs[] = {
MFD_CELL_RES("s2mps15-rtc", s2mpu05_rtc_resources),
};
+static const struct resource s2mu005_muic_resources[] = {
+ DEFINE_RES_IRQ_NAMED(S2MU005_IRQ_MUIC_ATTACH, "attach"),
+ DEFINE_RES_IRQ_NAMED(S2MU005_IRQ_MUIC_DETACH, "detach"),
+};
+
+static const struct mfd_cell s2mu005_devs[] = {
+ MFD_CELL_NAME("s2mu005-charger"),
+ MFD_CELL_OF("s2mu005-flash", NULL, NULL, 0, 0, "samsung,s2mu005-flash"),
+ MFD_CELL_OF("s2mu005-muic", s2mu005_muic_resources, NULL, 0, 0, "samsung,s2mu005-muic"),
+ MFD_CELL_OF("s2mu005-rgb", NULL, NULL, 0, 0, "samsung,s2mu005-rgb"),
+};
+
static void sec_pmic_dump_rev(struct sec_pmic_dev *sec_pmic)
{
unsigned int val;
@@ -250,6 +262,10 @@ int sec_pmic_probe(struct device *dev, int device_type, unsigned int irq,
sec_devs = s2mpu05_devs;
num_sec_devs = ARRAY_SIZE(s2mpu05_devs);
break;
+ case S2MU005:
+ sec_devs = s2mu005_devs;
+ num_sec_devs = ARRAY_SIZE(s2mu005_devs);
+ break;
default:
return dev_err_probe(sec_pmic->dev, -EINVAL,
"Unsupported device type %d\n",
diff --git a/drivers/mfd/sec-i2c.c b/drivers/mfd/sec-i2c.c
index 3132b849b4bc4..d8609886fcc80 100644
--- a/drivers/mfd/sec-i2c.c
+++ b/drivers/mfd/sec-i2c.c
@@ -17,6 +17,7 @@
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s2mps15.h>
#include <linux/mfd/samsung/s2mpu02.h>
+#include <linux/mfd/samsung/s2mu005.h>
#include <linux/mfd/samsung/s5m8767.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
@@ -66,6 +67,19 @@ static bool s2mpu02_volatile(struct device *dev, unsigned int reg)
}
}
+static bool s2mu005_volatile(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case S2MU005_REG_CHGR_INT1M:
+ case S2MU005_REG_FLED_INT1M:
+ case S2MU005_REG_MUIC_INT1M:
+ case S2MU005_REG_MUIC_INT2M:
+ return false;
+ default:
+ return true;
+ }
+}
+
static const struct regmap_config s2dos05_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -130,6 +144,15 @@ static const struct regmap_config s2mpu05_regmap_config = {
.val_bits = 8,
};
+static const struct regmap_config s2mu005_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = S2MU005_REG_MUIC_LDOADC_H,
+ .volatile_reg = s2mu005_volatile,
+ .cache_type = REGCACHE_FLAT_S,
+};
+
static const struct regmap_config s5m8767_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
@@ -203,6 +226,11 @@ static const struct sec_pmic_i2c_platform_data s2mpu05_data = {
.device_type = S2MPU05,
};
+static const struct sec_pmic_i2c_platform_data s2mu005_data = {
+ .regmap_cfg = &s2mu005_regmap_config,
+ .device_type = S2MU005,
+};
+
static const struct sec_pmic_i2c_platform_data s5m8767_data = {
.regmap_cfg = &s5m8767_regmap_config,
.device_type = S5M8767X,
@@ -217,6 +245,7 @@ static const struct of_device_id sec_pmic_i2c_of_match[] = {
{ .compatible = "samsung,s2mps15-pmic", .data = &s2mps15_data, },
{ .compatible = "samsung,s2mpu02-pmic", .data = &s2mpu02_data, },
{ .compatible = "samsung,s2mpu05-pmic", .data = &s2mpu05_data, },
+ { .compatible = "samsung,s2mu005-pmic", .data = &s2mu005_data, },
{ .compatible = "samsung,s5m8767-pmic", .data = &s5m8767_data, },
{ },
};
diff --git a/drivers/mfd/sec-irq.c b/drivers/mfd/sec-irq.c
index 133188391f7c2..91a2922463fb6 100644
--- a/drivers/mfd/sec-irq.c
+++ b/drivers/mfd/sec-irq.c
@@ -16,6 +16,7 @@
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s2mpu02.h>
#include <linux/mfd/samsung/s2mpu05.h>
+#include <linux/mfd/samsung/s2mu005.h>
#include <linux/mfd/samsung/s5m8767.h>
#include <linux/regmap.h>
#include "sec-core.h"
@@ -223,6 +224,65 @@ static const struct regmap_irq s2mpu05_irqs[] = {
REGMAP_IRQ_REG(S2MPU05_IRQ_TSD, 2, S2MPU05_IRQ_TSD_MASK),
};
+static const struct regmap_irq s2mu005_irqs[] = {
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_DETBAT, 0, S2MU005_IRQ_CHGR_DETBAT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_BAT, 0, S2MU005_IRQ_CHGR_BAT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_IVR, 0, S2MU005_IRQ_CHGR_IVR_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_EVENT, 0, S2MU005_IRQ_CHGR_EVENT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_CHG, 0, S2MU005_IRQ_CHGR_CHG_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_VMID, 0, S2MU005_IRQ_CHGR_VMID_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_WCIN, 0, S2MU005_IRQ_CHGR_WCIN_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_CHGR_VBUS, 0, S2MU005_IRQ_CHGR_VBUS_MASK),
+
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_LBPROT, 1, S2MU005_IRQ_FLED_LBPROT_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_OPENCH2, 1, S2MU005_IRQ_FLED_OPENCH2_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_OPENCH1, 1, S2MU005_IRQ_FLED_OPENCH1_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_SHORTCH2, 1, S2MU005_IRQ_FLED_SHORTCH2_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_FLED_SHORTCH1, 1, S2MU005_IRQ_FLED_SHORTCH1_MASK),
+
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_ATTACH, 2, S2MU005_IRQ_MUIC_ATTACH_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_DETACH, 2, S2MU005_IRQ_MUIC_DETACH_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_KP, 2, S2MU005_IRQ_MUIC_KP_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_LKP, 2, S2MU005_IRQ_MUIC_LKP_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_LKR, 2, S2MU005_IRQ_MUIC_LKR_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_RIDCHG, 2, S2MU005_IRQ_MUIC_RIDCHG_MASK),
+
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_VBUSON, 3, S2MU005_IRQ_MUIC_VBUSON_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_RSVD, 3, S2MU005_IRQ_MUIC_RSVD_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_ADC, 3, S2MU005_IRQ_MUIC_ADC_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_STUCK, 3, S2MU005_IRQ_MUIC_STUCK_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_STUCKRCV, 3, S2MU005_IRQ_MUIC_STUCKRCV_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_MHDL, 3, S2MU005_IRQ_MUIC_MHDL_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_AVCHG, 3, S2MU005_IRQ_MUIC_AVCHG_MASK),
+ REGMAP_IRQ_REG(S2MU005_IRQ_MUIC_VBUSOFF, 3, S2MU005_IRQ_MUIC_VBUSOFF_MASK),
+};
+
+static unsigned int s2mu005_irq_get_reg(struct regmap_irq_chip_data *data,
+ unsigned int base, int index)
+{
+ const unsigned int irqf_regs[] = {
+ S2MU005_REG_CHGR_INT1,
+ S2MU005_REG_FLED_INT1,
+ S2MU005_REG_MUIC_INT1,
+ S2MU005_REG_MUIC_INT2,
+ };
+ const unsigned int mask_regs[] = {
+ S2MU005_REG_CHGR_INT1M,
+ S2MU005_REG_FLED_INT1M,
+ S2MU005_REG_MUIC_INT1M,
+ S2MU005_REG_MUIC_INT2M,
+ };
+
+ switch (base) {
+ case S2MU005_REG_CHGR_INT1:
+ return irqf_regs[index];
+ case S2MU005_REG_CHGR_INT1M:
+ return mask_regs[index];
+ }
+
+ return base;
+}
+
static const struct regmap_irq s5m8767_irqs[] = {
REGMAP_IRQ_REG(S5M8767_IRQ_PWRR, 0, S5M8767_IRQ_PWRR_MASK),
REGMAP_IRQ_REG(S5M8767_IRQ_PWRF, 0, S5M8767_IRQ_PWRF_MASK),
@@ -337,6 +397,17 @@ static const struct regmap_irq_chip s2mpu05_irq_chip = {
.ack_base = S2MPU05_REG_INT1,
};
+static const struct regmap_irq_chip s2mu005_irq_chip = {
+ .name = "s2mu005",
+ .irqs = s2mu005_irqs,
+ .num_irqs = ARRAY_SIZE(s2mu005_irqs),
+ .num_regs = 4,
+ .status_base = S2MU005_REG_CHGR_INT1,
+ .mask_base = S2MU005_REG_CHGR_INT1M,
+ .ack_base = S2MU005_REG_CHGR_INT1,
+ .get_irq_reg = s2mu005_irq_get_reg,
+};
+
static const struct regmap_irq_chip s5m8767_irq_chip = {
.name = "s5m8767",
.irqs = s5m8767_irqs,
@@ -442,6 +513,9 @@ struct regmap_irq_chip_data *sec_irq_init(struct sec_pmic_dev *sec_pmic)
case S2MPU05:
sec_irq_chip = &s2mpu05_irq_chip;
break;
+ case S2MU005:
+ sec_irq_chip = &s2mu005_irq_chip;
+ break;
default:
return dev_err_ptr_probe(sec_pmic->dev, -EINVAL, "Unsupported device type %d\n",
sec_pmic->device_type);
diff --git a/include/linux/mfd/samsung/core.h b/include/linux/mfd/samsung/core.h
index 4480c631110a6..6191f409de945 100644
--- a/include/linux/mfd/samsung/core.h
+++ b/include/linux/mfd/samsung/core.h
@@ -47,6 +47,7 @@ enum sec_device_type {
S2MPS15X,
S2MPU02,
S2MPU05,
+ S2MU005,
};
/**
diff --git a/include/linux/mfd/samsung/irq.h b/include/linux/mfd/samsung/irq.h
index 6eab95de6fa83..19d0f0e12944f 100644
--- a/include/linux/mfd/samsung/irq.h
+++ b/include/linux/mfd/samsung/irq.h
@@ -408,6 +408,72 @@ enum s2mpu05_irq {
#define S2MPU05_IRQ_INT140C_MASK BIT(1)
#define S2MPU05_IRQ_TSD_MASK BIT(2)
+enum s2mu005_irq {
+ S2MU005_IRQ_CHGR_DETBAT,
+ S2MU005_IRQ_CHGR_BAT,
+ S2MU005_IRQ_CHGR_IVR,
+ S2MU005_IRQ_CHGR_EVENT,
+ S2MU005_IRQ_CHGR_CHG,
+ S2MU005_IRQ_CHGR_VMID,
+ S2MU005_IRQ_CHGR_WCIN,
+ S2MU005_IRQ_CHGR_VBUS,
+
+ S2MU005_IRQ_FLED_LBPROT,
+ S2MU005_IRQ_FLED_OPENCH2,
+ S2MU005_IRQ_FLED_OPENCH1,
+ S2MU005_IRQ_FLED_SHORTCH2,
+ S2MU005_IRQ_FLED_SHORTCH1,
+
+ S2MU005_IRQ_MUIC_ATTACH,
+ S2MU005_IRQ_MUIC_DETACH,
+ S2MU005_IRQ_MUIC_KP,
+ S2MU005_IRQ_MUIC_LKP,
+ S2MU005_IRQ_MUIC_LKR,
+ S2MU005_IRQ_MUIC_RIDCHG,
+
+ S2MU005_IRQ_MUIC_VBUSON,
+ S2MU005_IRQ_MUIC_RSVD,
+ S2MU005_IRQ_MUIC_ADC,
+ S2MU005_IRQ_MUIC_STUCK,
+ S2MU005_IRQ_MUIC_STUCKRCV,
+ S2MU005_IRQ_MUIC_MHDL,
+ S2MU005_IRQ_MUIC_AVCHG,
+ S2MU005_IRQ_MUIC_VBUSOFF,
+
+ S2MU005_IRQ_NR,
+};
+
+#define S2MU005_IRQ_CHGR_DETBAT_MASK BIT(0)
+#define S2MU005_IRQ_CHGR_BAT_MASK BIT(1)
+#define S2MU005_IRQ_CHGR_IVR_MASK BIT(2)
+#define S2MU005_IRQ_CHGR_EVENT_MASK BIT(3)
+#define S2MU005_IRQ_CHGR_CHG_MASK BIT(4)
+#define S2MU005_IRQ_CHGR_VMID_MASK BIT(5)
+#define S2MU005_IRQ_CHGR_WCIN_MASK BIT(6)
+#define S2MU005_IRQ_CHGR_VBUS_MASK BIT(7)
+
+#define S2MU005_IRQ_FLED_LBPROT_MASK BIT(2)
+#define S2MU005_IRQ_FLED_OPENCH2_MASK BIT(4)
+#define S2MU005_IRQ_FLED_OPENCH1_MASK BIT(5)
+#define S2MU005_IRQ_FLED_SHORTCH2_MASK BIT(6)
+#define S2MU005_IRQ_FLED_SHORTCH1_MASK BIT(7)
+
+#define S2MU005_IRQ_MUIC_ATTACH_MASK BIT(0)
+#define S2MU005_IRQ_MUIC_DETACH_MASK BIT(1)
+#define S2MU005_IRQ_MUIC_KP_MASK BIT(2)
+#define S2MU005_IRQ_MUIC_LKP_MASK BIT(3)
+#define S2MU005_IRQ_MUIC_LKR_MASK BIT(4)
+#define S2MU005_IRQ_MUIC_RIDCHG_MASK BIT(5)
+
+#define S2MU005_IRQ_MUIC_VBUSON_MASK BIT(0)
+#define S2MU005_IRQ_MUIC_RSVD_MASK BIT(1)
+#define S2MU005_IRQ_MUIC_ADC_MASK BIT(2)
+#define S2MU005_IRQ_MUIC_STUCK_MASK BIT(3)
+#define S2MU005_IRQ_MUIC_STUCKRCV_MASK BIT(4)
+#define S2MU005_IRQ_MUIC_MHDL_MASK BIT(5)
+#define S2MU005_IRQ_MUIC_AVCHG_MASK BIT(6)
+#define S2MU005_IRQ_MUIC_VBUSOFF_MASK BIT(7)
+
enum s5m8767_irq {
S5M8767_IRQ_PWRR,
S5M8767_IRQ_PWRF,
diff --git a/include/linux/mfd/samsung/s2mu005.h b/include/linux/mfd/samsung/s2mu005.h
new file mode 100644
index 0000000000000..46e7759545af2
--- /dev/null
+++ b/include/linux/mfd/samsung/s2mu005.h
@@ -0,0 +1,332 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (c) 2015 Samsung Electronics Co., Ltd
+ * Copyright (c) 2026 Kaustabh Chakraborty <kauschluss@disroot.org>
+ * Copyright (c) 2026 Łukasz Lebiedziński <kernel@lvkasz.us>
+ */
+
+#ifndef __LINUX_MFD_S2MU005_H
+#define __LINUX_MFD_S2MU005_H
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+
+/* S2MU005 registers */
+enum s2mu005_reg {
+ S2MU005_REG_CHGR_INT1,
+ S2MU005_REG_CHGR_INT1M,
+
+ S2MU005_REG_FLED_INT1,
+ S2MU005_REG_FLED_INT1M,
+
+ S2MU005_REG_MUIC_INT1,
+ S2MU005_REG_MUIC_INT2,
+ S2MU005_REG_MUIC_INT1M,
+ S2MU005_REG_MUIC_INT2M,
+
+ S2MU005_REG_CHGR_STATUS0,
+ S2MU005_REG_CHGR_STATUS1,
+ S2MU005_REG_CHGR_STATUS2,
+ S2MU005_REG_CHGR_STATUS3,
+ S2MU005_REG_CHGR_STATUS4,
+ S2MU005_REG_CHGR_STATUS5,
+ S2MU005_REG_CHGR_CTRL0,
+ S2MU005_REG_CHGR_CTRL1,
+ S2MU005_REG_CHGR_CTRL2,
+ S2MU005_REG_CHGR_CTRL3,
+ S2MU005_REG_CHGR_CTRL4,
+ S2MU005_REG_CHGR_CTRL5,
+ S2MU005_REG_CHGR_CTRL6,
+ S2MU005_REG_CHGR_CTRL7,
+ S2MU005_REG_CHGR_CTRL8,
+ S2MU005_REG_CHGR_CTRL9,
+ S2MU005_REG_CHGR_CTRL10,
+ S2MU005_REG_CHGR_CTRL11,
+ S2MU005_REG_CHGR_CTRL12,
+ S2MU005_REG_CHGR_CTRL13,
+ S2MU005_REG_CHGR_CTRL14,
+ S2MU005_REG_CHGR_CTRL15,
+ S2MU005_REG_CHGR_CTRL16,
+ S2MU005_REG_CHGR_CTRL17,
+ S2MU005_REG_CHGR_CTRL18,
+ S2MU005_REG_CHGR_CTRL19,
+ S2MU005_REG_CHGR_TEST0,
+ S2MU005_REG_CHGR_TEST1,
+ S2MU005_REG_CHGR_TEST2,
+ S2MU005_REG_CHGR_TEST3,
+ S2MU005_REG_CHGR_TEST4,
+ S2MU005_REG_CHGR_TEST5,
+ S2MU005_REG_CHGR_TEST6,
+ S2MU005_REG_CHGR_TEST7,
+ S2MU005_REG_CHGR_TEST8,
+ S2MU005_REG_CHGR_TEST9,
+ S2MU005_REG_CHGR_TEST10,
+
+ S2MU005_REG_FLED_STATUS,
+ S2MU005_REG_FLED_CH0_CTRL0,
+ S2MU005_REG_FLED_CH0_CTRL1,
+ S2MU005_REG_FLED_CH0_CTRL2,
+ S2MU005_REG_FLED_CH0_CTRL3,
+ S2MU005_REG_FLED_CH1_CTRL0,
+ S2MU005_REG_FLED_CH1_CTRL1,
+ S2MU005_REG_FLED_CH1_CTRL2,
+ S2MU005_REG_FLED_CH1_CTRL3,
+ S2MU005_REG_FLED_CTRL0,
+ S2MU005_REG_FLED_CTRL1,
+ S2MU005_REG_FLED_CTRL2,
+ S2MU005_REG_FLED_CTRL3,
+ S2MU005_REG_FLED_CTRL4,
+ S2MU005_REG_FLED_CTRL5,
+ S2MU005_REG_FLED_CTRL6,
+
+ S2MU005_REG_RGB_EN,
+ S2MU005_REG_RGB_CH0_CTRL,
+ S2MU005_REG_RGB_CH1_CTRL,
+ S2MU005_REG_RGB_CH2_CTRL,
+ S2MU005_REG_RGB_CH0_RAMP,
+ S2MU005_REG_RGB_CH0_STAY,
+ S2MU005_REG_RGB_CH1_RAMP,
+ S2MU005_REG_RGB_CH1_STAY,
+ S2MU005_REG_RGB_CH2_RAMP,
+ S2MU005_REG_RGB_CH2_STAY,
+ S2MU005_REG_RGB_TEST0,
+ S2MU005_REG_RGB_CTRL0,
+
+ S2MU005_REG_MUIC_ADC,
+ S2MU005_REG_MUIC_DEV1,
+ S2MU005_REG_MUIC_DEV2,
+ S2MU005_REG_MUIC_DEV3,
+ S2MU005_REG_MUIC_BUTTON1,
+ S2MU005_REG_MUIC_BUTTON2,
+ S2MU005_REG_MUIC_RESET,
+ S2MU005_REG_MUIC_CHGTYPE,
+ S2MU005_REG_MUIC_DEVAPPLE,
+ S2MU005_REG_MUIC_BCDRESCAN,
+ S2MU005_REG_MUIC_TEST1,
+ S2MU005_REG_MUIC_TEST2,
+ S2MU005_REG_MUIC_TEST3,
+
+ S2MU005_REG_ID = 0x73,
+
+ S2MU005_REG_MUIC_CTRL1 = 0xb2,
+ S2MU005_REG_MUIC_TIMERSET1,
+ S2MU005_REG_MUIC_TIMERSET2,
+ S2MU005_REG_MUIC_SWCTRL,
+ S2MU005_REG_MUIC_TIMERSET3,
+ S2MU005_REG_MUIC_CTRL2,
+ S2MU005_REG_MUIC_CTRL3,
+
+ S2MU005_REG_MUIC_LDOADC_L = 0xbf,
+ S2MU005_REG_MUIC_LDOADC_H,
+};
+
+#define S2MU005_REG_FLED_CH_CTRL0(x) (S2MU005_REG_FLED_CH0_CTRL0 + 4 * (x))
+#define S2MU005_REG_FLED_CH_CTRL1(x) (S2MU005_REG_FLED_CH0_CTRL1 + 4 * (x))
+#define S2MU005_REG_FLED_CH_CTRL2(x) (S2MU005_REG_FLED_CH0_CTRL2 + 4 * (x))
+#define S2MU005_REG_FLED_CH_CTRL3(x) (S2MU005_REG_FLED_CH0_CTRL3 + 4 * (x))
+
+#define S2MU005_REG_RGB_CH_CTRL(x) (S2MU005_REG_RGB_CH0_CTRL + 1 * (x))
+#define S2MU005_REG_RGB_CH_RAMP(x) (S2MU005_REG_RGB_CH0_RAMP + 2 * (x))
+#define S2MU005_REG_RGB_CH_STAY(x) (S2MU005_REG_RGB_CH0_STAY + 2 * (x))
+
+/* S2MU005_REG_CHGR_STATUS0 */
+#define S2MU005_CHGR_VBUS BIT(7)
+#define S2MU005_CHGR_WCIN BIT(6)
+#define S2MU005_CHGR_VMID BIT(5)
+#define S2MU005_CHGR_CHG BIT(4)
+#define S2MU005_CHGR_STAT GENMASK(3, 0)
+
+#define S2MU005_CHGR_STAT_DONE 8
+#define S2MU005_CHGR_STAT_TOPOFF 7
+#define S2MU005_CHGR_STAT_DONE_FLAG 6
+#define S2MU005_CHGR_STAT_CV 5
+#define S2MU005_CHGR_STAT_CC 4
+#define S2MU005_CHGR_STAT_COOL_CHG 3
+#define S2MU005_CHGR_STAT_PRE_CHG 2
+
+/* S2MU005_REG_CHGR_STATUS1 */
+#define S2MU005_CHGR_DETBAT BIT(7)
+#define S2MU005_CHGR_VBUS_OVP GENMASK(6, 4)
+
+#define S2MU005_CHGR_VBUS_OVP_OVERVOLT 2
+
+/* S2MU005_REG_CHGR_STATUS2 */
+#define S2MU005_CHGR_BAT GENMASK(6, 4)
+
+#define S2MU005_CHGR_BAT_VOLT_DET 7
+#define S2MU005_CHGR_BAT_FAST_CHG_DET 6
+#define S2MU005_CHGR_BAT_COOL_CHG_DET 5
+#define S2MU005_CHGR_BAT_LOW_CHG 2
+#define S2MU005_CHGR_BAT_SELF_DISCHG 1
+#define S2MU005_CHGR_BAT_OVP_DET 0
+
+/* S2MU005_REG_CHGR_STATUS3 */
+#define S2MU005_CHGR_EVT GENMASK(3, 0)
+
+#define S2MU005_CHGR_EVT_WDT_RST 6
+#define S2MU005_CHGR_EVT_WDT_SUSP 5
+#define S2MU005_CHGR_EVT_VSYS_VUVLO 4
+#define S2MU005_CHGR_EVT_VSYS_VOVP 3
+#define S2MU005_CHGR_EVT_THERM_FOLDBACK 2
+#define S2MU005_CHGR_EVT_THERM_SHUTDOWN 1
+
+/* S2MU005_REG_CHGR_CTRL0 */
+#define S2MU005_CHGR_CHG_EN BIT(4)
+#define S2MU005_CHGR_OP_MODE GENMASK(2, 0)
+
+#define S2MU005_CHGR_OP_MODE_OTG BIT(2)
+#define S2MU005_CHGR_OP_MODE_CHG BIT(1)
+
+/* S2MU005_REG_CHGR_CTRL1 */
+#define S2MU005_CHGR_VIN_DROP GENMASK(6, 4)
+
+/* S2MU005_REG_CHGR_CTRL2 */
+#define S2MU005_CHGR_IN_CURR_LIM GENMASK(5, 0)
+
+/* S2MU005_REG_CHGR_CTRL4 */
+#define S2MU005_CHGR_OTG_OCP_ON BIT(5)
+#define S2MU005_CHGR_OTG_OCP_OFF BIT(4)
+#define S2MU005_CHGR_OTG_OCP GENMASK(3, 2)
+#define S2MU005_CHGR_OTG_OCP_1P5A 0x3
+
+/* S2MU005_REG_CHGR_CTRL5 */
+#define S2MU005_CHGR_VMID_BOOST GENMASK(4, 0)
+#define S2MU005_CHGR_VMID_BOOST_5P1V 0x16
+
+/* S2MU005_REG_CHGR_CTRL6 */
+#define S2MU005_CHGR_COOL_CHG_CURR GENMASK(5, 0)
+
+/* S2MU005_REG_CHGR_CTRL7 */
+#define S2MU005_CHGR_FAST_CHG_CURR GENMASK(5, 0)
+
+/* S2MU005_REG_CHGR_CTRL8 */
+#define S2MU005_CHGR_VF_VBAT GENMASK(6, 1)
+
+/* S2MU005_REG_CHGR_CTRL10 */
+#define S2MU005_CHGR_TOPOFF_CURR(x) (GENMASK(3, 0) << 4 * (x))
+
+/* S2MU005_REG_CHGR_CTRL11 */
+#define S2MU005_CHGR_OSC_BOOST GENMASK(6, 5)
+#define S2MU005_CHGR_OSC_BUCK GENMASK(4, 3)
+#define S2MU005_CHGR_OSC_BOOST_2MHZ 0x3
+
+/* S2MU005_REG_CHGR_CTRL12 */
+#define S2MU005_CHGR_WDT GENMASK(2, 0)
+
+#define S2MU005_CHGR_WDT_ON BIT(2)
+#define S2MU005_CHGR_WDT_OFF BIT(1)
+
+/* S2MU005_REG_CHGR_CTRL15 */
+#define S2MU005_CHGR_OTG_EN GENMASK(3, 2)
+#define S2MU005_CHGR_OTG_EN_ON 0x3
+
+/* S2MU005_REG_FLED_STATUS */
+#define S2MU005_FLED_FLASH_STATUS(x) (BIT(7) >> 2 * (x))
+#define S2MU005_FLED_TORCH_STATUS(x) (BIT(6) >> 2 * (x))
+
+/* S2MU005_REG_FLED_CHx_CTRL0 */
+#define S2MU005_FLED_FLASH_IOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CHx_CTRL1 */
+#define S2MU005_FLED_TORCH_IOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CHx_CTRL2 */
+#define S2MU005_FLED_TORCH_TIMEOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CHx_CTRL3 */
+#define S2MU005_FLED_FLASH_TIMEOUT GENMASK(3, 0)
+
+/* S2MU005_REG_FLED_CTRL1 */
+#define S2MU005_FLED_CH_EN BIT(7)
+
+/*
+ * S2MU005_REG_FLED_CTRL4 - Rev. EVT0
+ * S2MU005_REG_FLED_CTRL6 - Rev. EVT1 and later
+ */
+#define S2MU005_FLED_FLASH_EN(x) (GENMASK(7, 6) >> 4 * (x))
+#define S2MU005_FLED_TORCH_EN(x) (GENMASK(5, 4) >> 4 * (x))
+
+/* S2MU005_REG_RGB_EN */
+#define S2MU005_RGB_RESET BIT(6)
+#define S2MU005_RGB_SLOPE GENMASK(5, 0)
+
+#define S2MU005_RGB_SLOPE_CONST (BIT(4) | BIT(2) | BIT(0))
+#define S2MU005_RGB_SLOPE_SMOOTH (BIT(5) | BIT(3) | BIT(1))
+
+/* S2MU005_REG_RGB_CHx_RAMP */
+#define S2MU005_RGB_CH_RAMP_UP GENMASK(7, 4)
+#define S2MU005_RGB_CH_RAMP_DN GENMASK(3, 0)
+
+/* S2MU005_REG_RGB_CHx_STAY */
+#define S2MU005_RGB_CH_STAY_HI GENMASK(7, 4)
+#define S2MU005_RGB_CH_STAY_LO GENMASK(3, 0)
+
+/* S2MU005_REG_MUIC_DEV1 */
+#define S2MU005_MUIC_OTG BIT(7)
+#define S2MU005_MUIC_DCP BIT(6)
+#define S2MU005_MUIC_CDP BIT(5)
+#define S2MU005_MUIC_T1_T2_CHG BIT(4)
+#define S2MU005_MUIC_UART BIT(3)
+#define S2MU005_MUIC_SDP BIT(2)
+#define S2MU005_MUIC_LANHUB BIT(1)
+#define S2MU005_MUIC_AUDIO BIT(0)
+
+/* S2MU005_REG_MUIC_DEV2 */
+#define S2MU005_MUIC_SDP_1P8S BIT(7)
+#define S2MU005_MUIC_AV BIT(6)
+#define S2MU005_MUIC_TTY BIT(5)
+#define S2MU005_MUIC_PPD BIT(4)
+#define S2MU005_MUIC_JIG_UART_OFF BIT(3)
+#define S2MU005_MUIC_JIG_UART_ON BIT(2)
+#define S2MU005_MUIC_JIG_USB_OFF BIT(1)
+#define S2MU005_MUIC_JIG_USB_ON BIT(0)
+
+/* S2MU005_REG_MUIC_DEV3 */
+#define S2MU005_MUIC_U200_CHG BIT(7)
+#define S2MU005_MUIC_VBUS_AV BIT(4)
+#define S2MU005_MUIC_VBUS_R255 BIT(1)
+#define S2MU005_MUIC_MHL BIT(0)
+
+/* S2MU005_REG_MUIC_DEVAPPLE */
+#define S2MU005_MUIC_APPLE_CHG_0P5A BIT(7)
+#define S2MU005_MUIC_APPLE_CHG_1P0A BIT(6)
+#define S2MU005_MUIC_APPLE_CHG_2P0A BIT(5)
+#define S2MU005_MUIC_APPLE_CHG_2P4A BIT(4)
+#define S2MU005_MUIC_SDP_DCD_OUT BIT(3)
+#define S2MU005_MUIC_RID_WAKEUP BIT(2)
+#define S2MU005_MUIC_VBUS_WAKEUP BIT(1)
+#define S2MU005_MUIC_BCV1P2_OR_OPEN BIT(0)
+
+/* S2MU005_REG_ID */
+#define S2MU005_ID_MASK GENMASK(3, 0)
+
+/* S2MU005_REG_MUIC_SWCTRL */
+#define S2MU005_MUIC_DM_DP GENMASK(7, 2)
+#define S2MU005_MUIC_JIG BIT(0)
+
+#define S2MU005_MUIC_DM_DP_UART 0x12
+#define S2MU005_MUIC_DM_DP_USB 0x09
+
+/* S2MU005_REG_MUIC_CTRL1 */
+#define S2MU005_MUIC_OPEN BIT(4)
+#define S2MU005_MUIC_RAW_DATA BIT(3)
+#define S2MU005_MUIC_MAN_SW BIT(2)
+#define S2MU005_MUIC_WAIT BIT(1)
+#define S2MU005_MUIC_IRQ BIT(0)
+
+/* S2MU005_REG_MUIC_CTRL3 */
+#define S2MU005_MUIC_ONESHOT_ADC BIT(2)
+
+/* S2MU005_REG_MUIC_LDOADC_L and S2MU005_REG_MUIC_LDOADC_H */
+#define S2MU005_MUIC_VSET GENMASK(4, 0)
+
+#define S2MU005_MUIC_VSET_3P0V 0x1f
+#define S2MU005_MUIC_VSET_2P6V 0x0e
+#define S2MU005_MUIC_VSET_2P4V 0x0c
+#define S2MU005_MUIC_VSET_2P2V 0x0a
+#define S2MU005_MUIC_VSET_2P0V 0x08
+#define S2MU005_MUIC_VSET_1P5V 0x03
+#define S2MU005_MUIC_VSET_1P4V 0x02
+#define S2MU005_MUIC_VSET_1P2V 0x00
+
+#endif /* __LINUX_MFD_S2MU005_H */
--
2.53.0
^ permalink raw reply related
* [PATCH v6 03/11] dt-bindings: mfd: add documentation for S2MU005 PMIC
From: Kaustabh Chakraborty @ 2026-05-15 10:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Samsung's S2MU005 PMIC includes subdevices for a charger, an MUIC (Micro
USB Interface Controller), and flash and RGB LED controllers.
Add the compatible and documentation for the S2MU005 PMIC. Also, add an
example for nodes for supported sub-devices, i.e. MUIC, flash LEDs, and
RGB LEDs. Charger sub-device uses the node of the parent.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../bindings/mfd/samsung,s2mu005-pmic.yaml | 120 +++++++++++++++++++++
1 file changed, 120 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
new file mode 100644
index 0000000000000..0e6afb7d2017b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/samsung,s2mu005-pmic.yaml
@@ -0,0 +1,120 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/samsung,s2mu005-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S2MU005 Power Management IC
+
+maintainers:
+ - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+ The S2MU005 is a companion power management IC which includes subdevices for
+ a charger controller, an MUIC (Micro USB Interface Controller), and flash and
+ RGB LED controllers.
+
+allOf:
+ - $ref: /schemas/power/supply/power-supply.yaml#
+
+properties:
+ compatible:
+ const: samsung,s2mu005-pmic
+
+ flash:
+ $ref: /schemas/leds/samsung,s2mu005-flash.yaml
+ description:
+ Child node describing flash LEDs.
+
+ interrupts:
+ maxItems: 1
+
+ muic:
+ $ref: /schemas/extcon/samsung,s2mu005-muic.yaml#
+ description:
+ Child node describing MUIC device.
+
+ multi-led:
+ type: object
+
+ allOf:
+ - $ref: /schemas/leds/leds-class-multicolor.yaml#
+
+ properties:
+ compatible:
+ const: samsung,s2mu005-rgb
+
+ required:
+ - compatible
+
+ unevaluatedProperties: false
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/leds/common.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@3d {
+ compatible = "samsung,s2mu005-pmic";
+ reg = <0x3d>;
+ interrupt-parent = <&gpa2>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ monitored-battery = <&battery>;
+
+ flash {
+ compatible = "samsung,s2mu005-flash";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ function-enumerator = <1>;
+ };
+ };
+
+ muic {
+ compatible = "samsung,s2mu005-muic";
+
+ connector {
+ compatible = "usb-b-connector";
+ label = "micro-USB";
+ type = "micro";
+ };
+
+ port {
+ muic_to_usb: endpoint {
+ remote-endpoint = <&usb_to_muic>;
+ };
+ };
+ };
+
+ multi-led {
+ compatible = "samsung,s2mu005-rgb";
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_INDICATOR;
+ linux,default-trigger = "pattern";
+ };
+ };
+ };
--
2.53.0
^ permalink raw reply related
* [PATCH v6 02/11] dt-bindings: extcon: document Samsung S2M series PMIC extcon device
From: Kaustabh Chakraborty @ 2026-05-15 10:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Certain Samsung S2M series PMICs have a MUIC device which reports
various cable states by measuring the ID-GND resistance with an internal
ADC. Document the devicetree schema for this device.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../bindings/extcon/samsung,s2mu005-muic.yaml | 40 ++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml b/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml
new file mode 100644
index 0000000000000..0a320d5e2a352
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/samsung,s2mu005-muic.yaml
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/samsung,s2mu005-muic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MUIC Device for Samsung S2M series PMICs
+
+maintainers:
+ - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+ The Samsung S2M series PMIC MUIC device is a USB port accessory
+ detector. It reports multiple states depending on the ID-GND
+ resistance measured by an internal ADC.
+
+ This is a part of device tree bindings for S2M and S5M family of Power
+ Management IC (PMIC).
+
+ See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for
+ additional information and example.
+
+properties:
+ compatible:
+ enum:
+ - samsung,s2mu005-muic
+
+ connector:
+ $ref: /schemas/connector/usb-connector.yaml#
+
+ port:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Port connecting to the USB controller or PHY.
+
+required:
+ - compatible
+ - connector
+ - port
+
+additionalProperties: false
--
2.53.0
^ permalink raw reply related
* [PATCH v6 01/11] dt-bindings: leds: document Samsung S2M series PMIC flash LED device
From: Kaustabh Chakraborty @ 2026-05-15 10:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty, Conor Dooley
In-Reply-To: <20260515-s2mu005-pmic-v6-0-1979106992d4@disroot.org>
Certain Samsung S2M series PMICs have a flash LED controller with
two LED channels, and with torch and flash control modes. Document the
devicetree schema for the device.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
.../bindings/leds/samsung,s2mu005-flash.yaml | 52 ++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/Documentation/devicetree/bindings/leds/samsung,s2mu005-flash.yaml b/Documentation/devicetree/bindings/leds/samsung,s2mu005-flash.yaml
new file mode 100644
index 0000000000000..36051ab20509f
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/samsung,s2mu005-flash.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/samsung,s2mu005-flash.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Flash and Torch LED Controller for Samsung S2M series PMICs
+
+maintainers:
+ - Kaustabh Chakraborty <kauschluss@disroot.org>
+
+description: |
+ The Samsung S2M series PMIC flash LED has two led channels (typically
+ as back and front camera flashes), with support for both torch and
+ flash modes.
+
+ This is a part of device tree bindings for S2M and S5M family of Power
+ Management IC (PMIC).
+
+ See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for
+ additional information and example.
+
+properties:
+ compatible:
+ enum:
+ - samsung,s2mu005-flash
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+patternProperties:
+ "^led@[0-1]$":
+ type: object
+ $ref: common.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ reg:
+ enum: [0, 1]
+
+ required:
+ - reg
+
+required:
+ - compatible
+ - "#address-cells"
+ - "#size-cells"
+
+additionalProperties: false
--
2.53.0
^ permalink raw reply related
* [PATCH v6 00/11] Support for Samsung S2MU005 PMIC and its sub-devices
From: Kaustabh Chakraborty @ 2026-05-15 10:38 UTC (permalink / raw)
To: Lee Jones, Pavel Machek, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
Krzysztof Kozlowski, André Draszik, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran,
Łukasz Lebiedziński
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc, Kaustabh Chakraborty, Conor Dooley
S2MU005 is an MFD chip manufactured by Samsung Electronics. This is
found in various devices manufactured by Samsung and others, including
all Exynos 7870 devices. It is known to have the following features:
1. Two LED channels with adjustable brightness for use as a torch, or a
flash strobe.
2. An RGB LED with 8-bit channels. Usually programmed as a notification
indicator.
3. An MUIC, which works with USB micro-B (and USB-C?). For the micro-B
variant though, it measures the ID-GND resistance using an internal
ADC.
4. A charger device, which reports if charger is online, voltage,
resistance, etc.
This patch series implements a lot of these features. Naturally, this
series touches upon a lot of subsystems. The 'parent' is the MFD driver,
so the subsystems have some form of dependency to the MFD driver, so
they are not separable.
Here are the subsystems corresponding to the patch numbers:
dt-bindings - 01, 02, 03
mfd - 03, 04, 05, 06
led - 01, 07, 08, 09
extcon - 02, 10
power - 11
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
---
Changes in v6:
- Fix build, UAF, and functional errors with
CONFIG_V4L2_FLASH_LED_CLASS=m (Lee Jones)
- Remove (ret < 0) wherever redundant (Lee Jones)
- Remove extra conditionals for supporting multiple variants (Lee Jones)
- Fix OOB condition in initailizing flash LED channels (Lee Jones)
- declare i inside for, like: for (int i = 0; ...) (Lee Jones)
- Rewrite and simplify closest timing function for clarity (Lee Jones)
- Link to v5: https://lore.kernel.org/r/20260424-s2mu005-pmic-v5-0-fcbc9da5a004@disroot.org
Changes in v5:
- Drop port property from charger dt binding (Krzysztof Kozlowski)
- Create separate dt binding for S2MU005 MFD (Krzysztof Kozlowski)
- Move RGB LED and charger schema to parent schema (Rob Herring)
- Fix error of using invalid revision mask
- Link to v4: https://lore.kernel.org/r/20260414-s2mu005-pmic-v4-0-7fe7480577e6@disroot.org
Changes in v4:
- Use OF graph to connect charger with MUIC in device tree
- Move DMA coherent mask to all MFD PMICs (André Draszik)
- Modify pointer names for flash/RGB drivers (Lee Jones)
- Use 100-char line wrap for flash/RGB drivers (Lee Jones)
- Revamp LED device initialization in flash driver (Lee Jones)
- Add proper USB 2.0 support in charger driver (Łukasz Lebiedziński)
- Link to v3: https://lore.kernel.org/r/20260225-s2mu005-pmic-v3-0-b4afee947603@disroot.org
Changes in v3:
- Remove "extcon" text from dt-bindings documentation (Rob Herring)
- Add connector for MUIC node
- Fix dt binding errors reported by robh's bot
- Fix kernel test robot const errors
- Remove FIELD_PREP() values in register header file (André Draszik)
- Add max_register, volatile_reg, cache_type (André Draszik)
- Redo [v2 07/12] to NOT store the PMIC revision (André Draszik)
- Add a commit to fix DMA coherent mask in I2C PMICs
- Implement various flow changes in flash LED driver (André Draszik)
- Use device_for_each_child_node_scoped() (André Draszik)
- Fix CFI panic in devm_add_action_or_reset()
- Link to v2: https://lore.kernel.org/r/20260126-s2mu005-pmic-v2-0-78f1a75f547a@disroot.org
Changes in v2:
- Drop [v1 06/13], instead use regmap_irq_chip::get_irq_regs()
- Remove references to driver in devicetree commits (Conor Dooley)
- Propagate errors of sec_pmic_store_rev() (André Draszik)
- Fix documentation language errors (Randy Dunlap)
- Link to v1: https://lore.kernel.org/r/20251114-s2mu005-pmic-v1-0-9e3184d3a0c9@disroot.org
To: Lee Jones <lee@kernel.org>
To: Pavel Machek <pavel@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Kaustabh Chakraborty <kauschluss@disroot.org>
To: MyungJoo Ham <myungjoo.ham@samsung.com>
To: Chanwoo Choi <cw00.choi@samsung.com>
To: Krzysztof Kozlowski <krzk@kernel.org>
To: André Draszik <andre.draszik@linaro.org>
To: Nam Tran <trannamatk@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Shuah Khan <skhan@linuxfoundation.org>
To: Sebastian Reichel <sre@kernel.org>
Cc: linux-leds@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
---
Kaustabh Chakraborty (11):
dt-bindings: leds: document Samsung S2M series PMIC flash LED device
dt-bindings: extcon: document Samsung S2M series PMIC extcon device
dt-bindings: mfd: add documentation for S2MU005 PMIC
mfd: sec: add support for S2MU005 PMIC
mfd: sec: set DMA coherent mask
mfd: sec: resolve PMIC revision in S2MU005
leds: flash: add support for Samsung S2M series PMIC flash LED device
leds: rgb: add support for Samsung S2M series PMIC RGB LED device
Documentation: leds: document pattern behavior of Samsung S2M series PMIC RGB LEDs
extcon: add support for Samsung S2M series PMIC extcon devices
power: supply: add support for Samsung S2M series PMIC charger device
.../bindings/extcon/samsung,s2mu005-muic.yaml | 40 ++
.../bindings/leds/samsung,s2mu005-flash.yaml | 52 +++
.../bindings/mfd/samsung,s2mu005-pmic.yaml | 120 ++++++
Documentation/leds/index.rst | 1 +
Documentation/leds/leds-s2m-rgb.rst | 60 +++
drivers/extcon/Kconfig | 10 +
drivers/extcon/Makefile | 1 +
drivers/extcon/extcon-s2m.c | 345 +++++++++++++++++
drivers/leds/flash/Kconfig | 12 +
drivers/leds/flash/Makefile | 1 +
drivers/leds/flash/leds-s2m-flash.c | 352 +++++++++++++++++
drivers/leds/rgb/Kconfig | 11 +
drivers/leds/rgb/Makefile | 1 +
drivers/leds/rgb/leds-s2m-rgb.c | 416 +++++++++++++++++++++
drivers/mfd/sec-common.c | 37 +-
drivers/mfd/sec-i2c.c | 29 ++
drivers/mfd/sec-irq.c | 74 ++++
drivers/power/supply/Kconfig | 11 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/s2m-charger.c | 299 +++++++++++++++
include/linux/mfd/samsung/core.h | 1 +
include/linux/mfd/samsung/irq.h | 66 ++++
include/linux/mfd/samsung/s2mu005.h | 332 ++++++++++++++++
23 files changed, 2266 insertions(+), 6 deletions(-)
---
base-commit: e98d21c170b01ddef366f023bbfcf6b31509fa83
change-id: 20251112-s2mu005-pmic-0c67fa6bac3c
Best regards,
--
Kaustabh Chakraborty <kauschluss@disroot.org>
^ permalink raw reply
* [PATCH v4 1/1] mfd: Add Host Interface (HIF) support for Nuvoton NCT6694
From: a0282524688 @ 2026-05-15 8:57 UTC (permalink / raw)
To: tmyu0, linusw, brgl, linux, andi.shyti, lee, mkl, mailhol,
alexandre.belloni, wim
Cc: linux-kernel, linux-gpio, linux-i2c, linux-can, netdev,
linux-watchdog, linux-hwmon, linux-rtc, linux-usb, Ming Yu
In-Reply-To: <20260515085746.114361-1-a0282524688@gmail.com>
From: Ming Yu <a0282524688@gmail.com>
The Nuvoton NCT6694 also provides a Host Interface (HIF) via eSPI
to the host to access its features.
Sub-devices can use the common functions nct6694_read_msg() and
nct6694_write_msg() to issue a command. They can also request
interrupts that will be called when the HIF device triggers a
shared memory interrupt.
To support multiple transports, the driver configuration is
updated to allow selecting between the USB and HIF interfaces.
Signed-off-by: Ming Yu <a0282524688@gmail.com>
---
Changes since version 3:
- Remove redundant module type macro definitions from sub-device drivers
that are now provided by the shared header <linux/mfd/nct6694.h>,
fixing -Wmacro-redefined warnings.
Changes since version 2:
- Restore per-device IDA and mfd_add_hotplug_devices()/PLATFORM_DEVID_AUTO
to avoid child device ID conflicts with multiple NCT6694 chips.
- Validate irq_find_mapping() return value before dispatching IRQs.
- Check superio_enter() return value in nct6694_irq_init().
Changes since version 1:
- Drop function pointers from Super-I/O access and use static inline
helpers with proper types.
MAINTAINERS | 1 +
drivers/gpio/gpio-nct6694.c | 7 -
drivers/hwmon/nct6694-hwmon.c | 21 -
drivers/i2c/busses/i2c-nct6694.c | 7 -
drivers/mfd/Kconfig | 47 +-
drivers/mfd/Makefile | 3 +-
drivers/mfd/nct6694-hif.c | 663 ++++++++++++++++++++++++++++
drivers/mfd/nct6694.c | 111 +++--
drivers/net/can/usb/nct6694_canfd.c | 6 -
drivers/rtc/rtc-nct6694.c | 7 -
drivers/watchdog/nct6694_wdt.c | 7 -
include/linux/mfd/nct6694.h | 54 ++-
12 files changed, 813 insertions(+), 121 deletions(-)
create mode 100644 drivers/mfd/nct6694-hif.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 6aa3fe2ee1bb..e39aad82132e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19091,6 +19091,7 @@ S: Supported
F: drivers/gpio/gpio-nct6694.c
F: drivers/hwmon/nct6694-hwmon.c
F: drivers/i2c/busses/i2c-nct6694.c
+F: drivers/mfd/nct6694-hif.c
F: drivers/mfd/nct6694.c
F: drivers/net/can/usb/nct6694_canfd.c
F: drivers/rtc/rtc-nct6694.c
diff --git a/drivers/gpio/gpio-nct6694.c b/drivers/gpio/gpio-nct6694.c
index a8607f0d9915..53bfc5983648 100644
--- a/drivers/gpio/gpio-nct6694.c
+++ b/drivers/gpio/gpio-nct6694.c
@@ -13,13 +13,6 @@
#include <linux/module.h>
#include <linux/platform_device.h>
-/*
- * USB command module type for NCT6694 GPIO controller.
- * This defines the module type used for communication with the NCT6694
- * GPIO controller over the USB interface.
- */
-#define NCT6694_GPIO_MOD 0xFF
-
#define NCT6694_GPIO_VER 0x90
#define NCT6694_GPIO_VALID 0x110
#define NCT6694_GPI_DATA 0x120
diff --git a/drivers/hwmon/nct6694-hwmon.c b/drivers/hwmon/nct6694-hwmon.c
index 6dcf22ca5018..581451875f2c 100644
--- a/drivers/hwmon/nct6694-hwmon.c
+++ b/drivers/hwmon/nct6694-hwmon.c
@@ -15,13 +15,6 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
-/*
- * USB command module type for NCT6694 report channel
- * This defines the module type used for communication with the NCT6694
- * report channel over the USB interface.
- */
-#define NCT6694_RPT_MOD 0xFF
-
/* Report channel */
/*
* The report channel is used to report the status of the hardware monitor
@@ -38,13 +31,6 @@
#define NCT6694_TIN_STS(x) (0x6A + (x))
#define NCT6694_FIN_STS(x) (0x6E + (x))
-/*
- * USB command module type for NCT6694 HWMON controller.
- * This defines the module type used for communication with the NCT6694
- * HWMON controller over the USB interface.
- */
-#define NCT6694_HWMON_MOD 0x00
-
/* Command 00h - Hardware Monitor Control */
#define NCT6694_HWMON_CONTROL 0x00
#define NCT6694_HWMON_CONTROL_SEL 0x00
@@ -53,13 +39,6 @@
#define NCT6694_HWMON_ALARM 0x02
#define NCT6694_HWMON_ALARM_SEL 0x00
-/*
- * USB command module type for NCT6694 PWM controller.
- * This defines the module type used for communication with the NCT6694
- * PWM controller over the USB interface.
- */
-#define NCT6694_PWM_MOD 0x01
-
/* PWM Command - Manual Control */
#define NCT6694_PWM_CONTROL 0x01
#define NCT6694_PWM_CONTROL_SEL 0x00
diff --git a/drivers/i2c/busses/i2c-nct6694.c b/drivers/i2c/busses/i2c-nct6694.c
index 1413ab6f9462..ef3329f34246 100644
--- a/drivers/i2c/busses/i2c-nct6694.c
+++ b/drivers/i2c/busses/i2c-nct6694.c
@@ -12,13 +12,6 @@
#include <linux/module.h>
#include <linux/platform_device.h>
-/*
- * USB command module type for NCT6694 I2C controller.
- * This defines the module type used for communication with the NCT6694
- * I2C controller over the USB interface.
- */
-#define NCT6694_I2C_MOD 0x03
-
/* Command 00h - I2C Deliver */
#define NCT6694_I2C_DELIVER 0x00
#define NCT6694_I2C_DELIVER_SEL 0x00
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 7192c9d1d268..8a715ec2f79f 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1164,19 +1164,46 @@ config MFD_MENF21BMC
will be called menf21bmc.
config MFD_NCT6694
- tristate "Nuvoton NCT6694 support"
+ tristate
select MFD_CORE
+ help
+ Core MFD support for the Nuvoton NCT6694 peripheral expander.
+ This provides the common APIs and shared structures used by all
+ interfaces (USB, HIF) to access the NCT6694 hardware features
+ such as GPIO, I2C, CAN-FD, Watchdog, ADC, PWM, and RTC.
+
+ It is selected automatically by the transport interface drivers.
+
+config MFD_NCT6694_HIF
+ tristate "Nuvoton NCT6694 HIF (eSPI) interface support"
+ depends on HAS_IOPORT && ACPI
+ select MFD_NCT6694
+ select REGMAP_MMIO
+ help
+ This enables support for the Nuvoton NCT6694 peripheral expander
+ connected via the Host Interface (HIF) using eSPI transport.
+
+ The transport driver uses Super-I/O mapping and shared memory to
+ communicate with the NCT6694 firmware. Enable this option if you
+ are using the NCT6694 over an eSPI interface on an ACPI platform.
+
+ To compile this driver as a module, choose M here: the module
+ will be called nct6694-hif.
+
+config MFD_NCT6694_USB
+ tristate "Nuvoton NCT6694 USB interface support"
+ select MFD_NCT6694
depends on USB
help
- This enables support for the Nuvoton USB device NCT6694, which shares
- peripherals.
- The Nuvoton NCT6694 is a peripheral expander with 16 GPIO chips,
- 6 I2C controllers, 2 CANfd controllers, 2 Watchdog timers, ADC,
- PWM, and RTC.
- This driver provides core APIs to access the NCT6694 hardware
- monitoring and control features.
- Additional drivers must be enabled to utilize the specific
- functionalities of the device.
+ This enables support for the Nuvoton NCT6694 peripheral expander
+ connected via the USB interface.
+
+ The transport driver uses USB bulk and interrupt transfers to
+ communicate with the NCT6694 firmware. Enable this option if you
+ are using the NCT6694 via a USB connection.
+
+ To compile this driver as a module, choose M here: the module
+ will be called nct6694.
config MFD_OCELOT
tristate "Microsemi Ocelot External Control Support"
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index e75e8045c28a..4cee9b74978c 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -124,7 +124,8 @@ obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
obj-$(CONFIG_MFD_PF1550) += pf1550.o
-obj-$(CONFIG_MFD_NCT6694) += nct6694.o
+obj-$(CONFIG_MFD_NCT6694_HIF) += nct6694-hif.o
+obj-$(CONFIG_MFD_NCT6694_USB) += nct6694.o
obj-$(CONFIG_MFD_CORE) += mfd-core.o
diff --git a/drivers/mfd/nct6694-hif.c b/drivers/mfd/nct6694-hif.c
new file mode 100644
index 000000000000..ca8c08b0d2e3
--- /dev/null
+++ b/drivers/mfd/nct6694-hif.c
@@ -0,0 +1,663 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2026 Nuvoton Technology Corp.
+ *
+ * Nuvoton NCT6694 host-interface (eSPI) transport driver.
+ */
+
+#include <linux/acpi.h>
+#include <linux/bits.h>
+#include <linux/idr.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/nct6694.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/unaligned.h>
+
+#define DRVNAME "nct6694-hif"
+
+#define NCT6694_POLL_INTERVAL_US 10
+#define NCT6694_POLL_TIMEOUT_US 10000
+
+/*
+ * Super-I/O registers
+ */
+#define SIO_REG_LDSEL 0x07 /* Logical device select */
+#define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */
+#define SIO_REG_LD_SHM 0x0F /* Logical device shared memory control */
+
+#define SIO_REG_SHM_ENABLE 0x30 /* Enable shared memory */
+#define SIO_REG_SHM_BASE_ADDR 0x60 /* Shared memory base address (2 bytes) */
+#define SIO_REG_SHM_IRQ_NR 0x70 /* Shared memory interrupt number */
+
+#define SIO_REG_UNLOCK_KEY 0x87 /* Key to enable Super-I/O */
+#define SIO_REG_LOCK_KEY 0xAA /* Key to disable Super-I/O */
+
+#define SIO_NCT6694B_ID 0xD029
+#define SIO_NCT6694D_ID 0x5832
+
+/*
+ * Super-I/O Shared Memory Logical Device registers
+ */
+#define NCT6694_SHM_COFS_STS 0x2E
+#define NCT6694_SHM_COFS_STS_COFS4W BIT(7)
+
+#define NCT6694_SHM_COFS_CTL2 0x3B
+#define NCT6694_SHM_COFS_CTL2_COFS4W_IE BIT(3)
+
+#define NCT6694_SHM_INTR_STATUS 0x9C /* Interrupt status register (4 bytes) */
+
+enum nct6694_chips {
+ NCT6694B = 0,
+ NCT6694D,
+};
+
+enum nct6694_module_id {
+ NCT6694_GPIO0 = 0,
+ NCT6694_GPIO1,
+ NCT6694_GPIO2,
+ NCT6694_GPIO3,
+ NCT6694_GPIO4,
+ NCT6694_GPIO5,
+ NCT6694_GPIO6,
+ NCT6694_GPIO7,
+ NCT6694_GPIO8,
+ NCT6694_GPIO9,
+ NCT6694_GPIOA,
+ NCT6694_GPIOB,
+ NCT6694_GPIOC,
+ NCT6694_GPIOD,
+ NCT6694_GPIOE,
+ NCT6694_GPIOF,
+ NCT6694_I2C0,
+ NCT6694_I2C1,
+ NCT6694_I2C2,
+ NCT6694_I2C3,
+ NCT6694_I2C4,
+ NCT6694_I2C5,
+ NCT6694_CAN0,
+ NCT6694_CAN1,
+};
+
+struct __packed nct6694_msg {
+ struct nct6694_cmd_header cmd_header;
+ struct nct6694_response_header response_header;
+ unsigned char *data;
+};
+
+struct nct6694_sio_data {
+ enum nct6694_chips chip;
+ int sioreg; /* Super-I/O index port */
+};
+
+struct nct6694_hif_data {
+ struct regmap *regmap;
+ struct mutex msg_lock;
+ struct nct6694_sio_data *sio_data;
+ void __iomem *msg_base;
+ unsigned int shm_base;
+};
+
+static const char * const nct6694_chip_names[] = {
+ "NCT6694D",
+ "NCT6694B"
+};
+
+/*
+ * Super-I/O functions.
+ */
+static inline int superio_enter(struct nct6694_sio_data *sio_data)
+{
+ int ioreg = sio_data->sioreg;
+
+ /*
+ * Try to reserve <ioreg> and <ioreg + 1> for exclusive access.
+ */
+ if (!request_muxed_region(ioreg, 2, DRVNAME))
+ return -EBUSY;
+
+ outb(SIO_REG_UNLOCK_KEY, ioreg);
+ outb(SIO_REG_UNLOCK_KEY, ioreg);
+
+ return 0;
+}
+
+static inline void superio_exit(struct nct6694_sio_data *sio_data)
+{
+ int ioreg = sio_data->sioreg;
+
+ outb(SIO_REG_LOCK_KEY, ioreg);
+
+ release_region(ioreg, 2);
+}
+
+static inline void superio_select(struct nct6694_sio_data *sio_data, int ld)
+{
+ int ioreg = sio_data->sioreg;
+
+ outb(SIO_REG_LDSEL, ioreg);
+ outb(ld, ioreg + 1);
+}
+
+static inline int superio_inb(struct nct6694_sio_data *sio_data, int reg)
+{
+ int ioreg = sio_data->sioreg;
+
+ outb(reg, ioreg);
+ return inb(ioreg + 1);
+}
+
+static inline int superio_inw(struct nct6694_sio_data *sio_data, int reg)
+{
+ int ioreg = sio_data->sioreg;
+ int val;
+
+ outb(reg++, ioreg);
+ val = inb(ioreg + 1) << 8;
+ outb(reg, ioreg);
+ val |= inb(ioreg + 1);
+
+ return val;
+}
+
+static inline void superio_outb(struct nct6694_sio_data *sio_data, int reg, u8 val)
+{
+ int ioreg = sio_data->sioreg;
+
+ outb(reg, ioreg);
+ outb(val, ioreg + 1);
+}
+
+static int nct6694_sio_find(struct nct6694_sio_data *sio_data, u8 sioreg)
+{
+ int ret;
+ u16 devid;
+
+ sio_data->sioreg = sioreg;
+
+ ret = superio_enter(sio_data);
+ if (ret)
+ return ret;
+
+ /* Check Chip ID */
+ devid = superio_inw(sio_data, SIO_REG_DEVID);
+ switch (devid) {
+ case SIO_NCT6694B_ID:
+ sio_data->chip = NCT6694B;
+ break;
+ case SIO_NCT6694D_ID:
+ sio_data->chip = NCT6694D;
+ break;
+ default:
+ pr_err("Unsupported device 0x%04x\n", devid);
+ goto err;
+ }
+
+ pr_info("Found %s at %#x\n", nct6694_chip_names[sio_data->chip], sio_data->sioreg);
+
+ superio_exit(sio_data);
+
+ return 0;
+
+err:
+ superio_exit(sio_data);
+ return -ENODEV;
+}
+
+static const struct mfd_cell_acpi_match nct6694_acpi_match_gpio[] = {
+ { .adr = NCT6694_GPIO0 },
+ { .adr = NCT6694_GPIO1 },
+ { .adr = NCT6694_GPIO2 },
+ { .adr = NCT6694_GPIO3 },
+ { .adr = NCT6694_GPIO4 },
+ { .adr = NCT6694_GPIO5 },
+ { .adr = NCT6694_GPIO6 },
+ { .adr = NCT6694_GPIO7 },
+ { .adr = NCT6694_GPIO8 },
+ { .adr = NCT6694_GPIO9 },
+ { .adr = NCT6694_GPIOA },
+ { .adr = NCT6694_GPIOB },
+ { .adr = NCT6694_GPIOC },
+ { .adr = NCT6694_GPIOD },
+ { .adr = NCT6694_GPIOE },
+ { .adr = NCT6694_GPIOF },
+};
+
+static const struct mfd_cell_acpi_match nct6694_acpi_match_i2c[] = {
+ { .adr = NCT6694_I2C0 },
+ { .adr = NCT6694_I2C1 },
+ { .adr = NCT6694_I2C2 },
+ { .adr = NCT6694_I2C3 },
+ { .adr = NCT6694_I2C4 },
+ { .adr = NCT6694_I2C5 },
+};
+
+static const struct mfd_cell_acpi_match nct6694_acpi_match_can[] = {
+ { .adr = NCT6694_CAN0 },
+ { .adr = NCT6694_CAN1 },
+};
+
+static const struct mfd_cell nct6694_devs[] = {
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[0]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[1]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[2]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[3]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[4]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[5]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[6]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[7]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[8]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[9]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[10]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[11]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[12]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[13]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[14]),
+ MFD_CELL_ACPI("nct6694-gpio", NULL, NULL, 0, 0, &nct6694_acpi_match_gpio[15]),
+
+ MFD_CELL_ACPI("nct6694-i2c", NULL, NULL, 0, 0, &nct6694_acpi_match_i2c[0]),
+ MFD_CELL_ACPI("nct6694-i2c", NULL, NULL, 0, 0, &nct6694_acpi_match_i2c[1]),
+ MFD_CELL_ACPI("nct6694-i2c", NULL, NULL, 0, 0, &nct6694_acpi_match_i2c[2]),
+ MFD_CELL_ACPI("nct6694-i2c", NULL, NULL, 0, 0, &nct6694_acpi_match_i2c[3]),
+ MFD_CELL_ACPI("nct6694-i2c", NULL, NULL, 0, 0, &nct6694_acpi_match_i2c[4]),
+ MFD_CELL_ACPI("nct6694-i2c", NULL, NULL, 0, 0, &nct6694_acpi_match_i2c[5]),
+
+ MFD_CELL_ACPI("nct6694-canfd", NULL, NULL, 0, 0, &nct6694_acpi_match_can[0]),
+ MFD_CELL_ACPI("nct6694-canfd", NULL, NULL, 0, 0, &nct6694_acpi_match_can[1]),
+};
+
+static int nct6694_response_err_handling(struct nct6694 *nct6694, unsigned char err_status)
+{
+ switch (err_status) {
+ case NCT6694_NO_ERROR:
+ return 0;
+ case NCT6694_NOT_SUPPORT_ERROR:
+ dev_err(nct6694->dev, "Command is not supported!\n");
+ break;
+ case NCT6694_NO_RESPONSE_ERROR:
+ dev_warn(nct6694->dev, "Command received no response!\n");
+ break;
+ case NCT6694_TIMEOUT_ERROR:
+ dev_warn(nct6694->dev, "Command timed out!\n");
+ break;
+ case NCT6694_PENDING:
+ dev_err(nct6694->dev, "Command is pending!\n");
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return -EIO;
+}
+
+static int nct6694_xfer_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ u8 hctrl, void *buf)
+{
+ struct nct6694_hif_data *hdata = nct6694->priv;
+ void __iomem *hdr = hdata->msg_base + offsetof(struct nct6694_msg, cmd_header);
+ struct nct6694_cmd_header cmd = *cmd_hd;
+ struct nct6694_response_header resp;
+ u16 len = le16_to_cpu(cmd.len);
+ u8 status;
+ int ret;
+
+ guard(mutex)(&hdata->msg_lock);
+
+ /* Wait until the previous command is completed */
+ ret = readb_poll_timeout(hdr + offsetof(struct nct6694_cmd_header, hctrl),
+ status, status == 0, NCT6694_POLL_INTERVAL_US,
+ NCT6694_POLL_TIMEOUT_US);
+ if (ret)
+ return ret;
+
+ /*
+ * Write cmd header fields, but skip hctrl — writing to it triggers
+ * firmware command processing and must be deferred until data is ready.
+ */
+ memcpy_toio(hdr, &cmd, offsetof(struct nct6694_cmd_header, hctrl));
+ memcpy_toio(hdr + offsetof(struct nct6694_cmd_header, rsv2), &cmd.rsv2,
+ sizeof(cmd) - offsetof(struct nct6694_cmd_header, rsv2));
+
+ if (hctrl == NCT6694_HCTRL_SET && len)
+ memcpy_toio(hdata->msg_base + offsetof(struct nct6694_msg, data),
+ buf, len);
+
+ /* Write hctrl last to trigger command processing */
+ writeb(hctrl, hdr + offsetof(struct nct6694_cmd_header, hctrl));
+
+ ret = readb_poll_timeout(hdr + offsetof(struct nct6694_cmd_header, hctrl),
+ status, status == 0, NCT6694_POLL_INTERVAL_US,
+ NCT6694_POLL_TIMEOUT_US);
+ if (ret)
+ return ret;
+
+ memcpy_fromio(&resp, hdata->msg_base + offsetof(struct nct6694_msg, response_header),
+ sizeof(resp));
+
+ ret = nct6694_response_err_handling(nct6694, resp.sts);
+ if (ret)
+ return ret;
+
+ if (le16_to_cpu(resp.len))
+ memcpy_fromio(buf, hdata->msg_base + offsetof(struct nct6694_msg, data),
+ min(len, le16_to_cpu(resp.len)));
+
+ return 0;
+}
+
+/**
+ * nct6694_hif_read_msg() - Send a command and read response data via HIF
+ * @nct6694: NCT6694 device data
+ * @cmd_hd: command header
+ * @buf: buffer to store response data
+ *
+ * Return: 0 on success or negative errno on failure.
+ */
+static int nct6694_hif_read_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf)
+{
+ struct nct6694_hif_data *hdata = nct6694->priv;
+
+ if (cmd_hd->mod == NCT6694_RPT_MOD)
+ return regmap_bulk_read(hdata->regmap,
+ le16_to_cpu(cmd_hd->offset),
+ buf, le16_to_cpu(cmd_hd->len));
+ return nct6694_xfer_msg(nct6694, cmd_hd, NCT6694_HCTRL_GET, buf);
+}
+
+/**
+ * nct6694_hif_write_msg() - Send a command with data payload via HIF
+ * @nct6694: NCT6694 device data
+ * @cmd_hd: command header
+ * @buf: buffer containing data to send
+ *
+ * Return: 0 on success or negative errno on failure.
+ */
+static int nct6694_hif_write_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf)
+{
+ struct nct6694_hif_data *hdata = nct6694->priv;
+
+ if (cmd_hd->mod == NCT6694_RPT_MOD)
+ return regmap_bulk_write(hdata->regmap,
+ le16_to_cpu(cmd_hd->offset),
+ buf, le16_to_cpu(cmd_hd->len));
+ return nct6694_xfer_msg(nct6694, cmd_hd, NCT6694_HCTRL_SET, buf);
+}
+
+static const struct regmap_config nct6694_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .reg_stride = 1,
+};
+
+static irqreturn_t nct6694_irq_handler(int irq, void *data)
+{
+ struct nct6694 *nct6694 = data;
+ struct nct6694_hif_data *hdata = nct6694->priv;
+ u8 reg_data[4];
+ u32 intr_status;
+ int ret;
+
+ /* Check interrupt status is set */
+ if (!(inb(hdata->shm_base + NCT6694_SHM_COFS_STS) & NCT6694_SHM_COFS_STS_COFS4W))
+ return IRQ_NONE;
+
+ /* Clear interrupt status */
+ outb(NCT6694_SHM_COFS_STS_COFS4W, hdata->shm_base + NCT6694_SHM_COFS_STS);
+
+ ret = regmap_bulk_read(hdata->regmap, NCT6694_SHM_INTR_STATUS,
+ reg_data, ARRAY_SIZE(reg_data));
+ if (ret)
+ return IRQ_NONE;
+
+ intr_status = get_unaligned_le32(reg_data);
+
+ while (intr_status) {
+ int hwirq = __ffs(intr_status);
+ unsigned int virq = irq_find_mapping(nct6694->domain, hwirq);
+
+ if (virq)
+ generic_handle_irq_safe(virq);
+ intr_status &= ~BIT(hwirq);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void nct6694_irq_release(void *data)
+{
+ struct nct6694 *nct6694 = data;
+ struct nct6694_hif_data *hdata = nct6694->priv;
+ unsigned char cofs_ctl2;
+
+ /* Disable SIRQ interrupt */
+ cofs_ctl2 = inb(hdata->shm_base + NCT6694_SHM_COFS_CTL2);
+ cofs_ctl2 &= ~NCT6694_SHM_COFS_CTL2_COFS4W_IE;
+ outb(cofs_ctl2, hdata->shm_base + NCT6694_SHM_COFS_CTL2);
+}
+
+static int nct6694_irq_init(struct nct6694 *nct6694, int irq)
+{
+ struct nct6694_hif_data *hdata = nct6694->priv;
+ struct nct6694_sio_data *sio_data = hdata->sio_data;
+ unsigned char cofs_ctl2;
+ int ret;
+
+ /* Set SIRQ number */
+ ret = superio_enter(sio_data);
+ if (ret)
+ return ret;
+
+ superio_select(sio_data, SIO_REG_LD_SHM);
+
+ if (!superio_inb(sio_data, SIO_REG_SHM_ENABLE)) {
+ superio_exit(sio_data);
+ return -EIO;
+ }
+
+ hdata->shm_base = superio_inw(sio_data, SIO_REG_SHM_BASE_ADDR);
+
+ superio_outb(sio_data, SIO_REG_SHM_IRQ_NR, irq);
+
+ superio_exit(sio_data);
+
+ /* Enable SIRQ interrupt */
+ cofs_ctl2 = inb(hdata->shm_base + NCT6694_SHM_COFS_CTL2);
+ cofs_ctl2 |= NCT6694_SHM_COFS_CTL2_COFS4W_IE;
+ outb(cofs_ctl2, hdata->shm_base + NCT6694_SHM_COFS_CTL2);
+
+ return 0;
+}
+
+static void nct6694_irq_enable(struct irq_data *data)
+{
+ struct nct6694 *nct6694 = irq_data_get_irq_chip_data(data);
+ irq_hw_number_t hwirq = irqd_to_hwirq(data);
+
+ guard(spinlock_irqsave)(&nct6694->irq_lock);
+
+ nct6694->irq_enable |= BIT(hwirq);
+}
+
+static void nct6694_irq_disable(struct irq_data *data)
+{
+ struct nct6694 *nct6694 = irq_data_get_irq_chip_data(data);
+ irq_hw_number_t hwirq = irqd_to_hwirq(data);
+
+ guard(spinlock_irqsave)(&nct6694->irq_lock);
+
+ nct6694->irq_enable &= ~BIT(hwirq);
+}
+
+static const struct irq_chip nct6694_irq_chip = {
+ .name = "nct6694-irq",
+ .flags = IRQCHIP_SKIP_SET_WAKE,
+ .irq_enable = nct6694_irq_enable,
+ .irq_disable = nct6694_irq_disable,
+};
+
+static void nct6694_irq_domain_remove(void *data)
+{
+ struct nct6694 *nct6694 = data;
+
+ irq_domain_remove(nct6694->domain);
+}
+
+static int nct6694_irq_domain_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+{
+ struct nct6694 *nct6694 = d->host_data;
+
+ irq_set_chip_data(irq, nct6694);
+ irq_set_chip_and_handler(irq, &nct6694_irq_chip, handle_simple_irq);
+
+ return 0;
+}
+
+static void nct6694_irq_domain_unmap(struct irq_domain *d, unsigned int irq)
+{
+ irq_set_chip_and_handler(irq, NULL, NULL);
+ irq_set_chip_data(irq, NULL);
+}
+
+static const struct irq_domain_ops nct6694_irq_domain_ops = {
+ .map = nct6694_irq_domain_map,
+ .unmap = nct6694_irq_domain_unmap,
+};
+
+static void nct6694_ida_destroy(void *data)
+{
+ struct nct6694 *nct6694 = data;
+
+ ida_destroy(&nct6694->wdt_ida);
+ ida_destroy(&nct6694->canfd_ida);
+ ida_destroy(&nct6694->i2c_ida);
+ ida_destroy(&nct6694->gpio_ida);
+}
+
+static const u8 sio_addrs[] = { 0x2e, 0x4e };
+
+static int nct6694_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct nct6694_sio_data *sio_data;
+ struct nct6694_hif_data *hdata;
+ struct nct6694 *data;
+ void __iomem *rpt_base, *msg_base;
+ int ret, i, irq;
+
+ sio_data = devm_kzalloc(dev, sizeof(*sio_data), GFP_KERNEL);
+ if (!sio_data)
+ return -ENOMEM;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ hdata = devm_kzalloc(dev, sizeof(*hdata), GFP_KERNEL);
+ if (!hdata)
+ return -ENOMEM;
+
+ rpt_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(rpt_base))
+ return PTR_ERR(rpt_base);
+ msg_base = devm_platform_ioremap_resource(pdev, 1);
+ if (IS_ERR(msg_base))
+ return PTR_ERR(msg_base);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ for (i = 0; i < ARRAY_SIZE(sio_addrs); i++) {
+ ret = nct6694_sio_find(sio_data, sio_addrs[i]);
+ if (!ret)
+ break;
+ }
+ if (ret)
+ return ret;
+
+ hdata->sio_data = sio_data;
+ hdata->msg_base = msg_base;
+ hdata->regmap = devm_regmap_init_mmio(dev, rpt_base,
+ &nct6694_regmap_config);
+ if (IS_ERR(hdata->regmap))
+ return PTR_ERR(hdata->regmap);
+
+ data->dev = dev;
+ data->priv = hdata;
+ data->read_msg = nct6694_hif_read_msg;
+ data->write_msg = nct6694_hif_write_msg;
+
+ spin_lock_init(&data->irq_lock);
+
+ ida_init(&data->gpio_ida);
+ ida_init(&data->i2c_ida);
+ ida_init(&data->canfd_ida);
+ ida_init(&data->wdt_ida);
+
+ ret = devm_add_action_or_reset(dev, nct6694_ida_destroy, data);
+ if (ret)
+ return ret;
+
+ data->domain = irq_domain_create_simple(NULL, NCT6694_NR_IRQS, 0,
+ &nct6694_irq_domain_ops,
+ data);
+ if (!data->domain)
+ return -ENODEV;
+
+ ret = devm_add_action_or_reset(dev, nct6694_irq_domain_remove, data);
+ if (ret)
+ return ret;
+
+ ret = nct6694_irq_init(data, irq);
+ if (ret)
+ return ret;
+
+ ret = devm_add_action_or_reset(dev, nct6694_irq_release, data);
+ if (ret)
+ return ret;
+
+ ret = devm_request_threaded_irq(dev, irq, NULL, nct6694_irq_handler,
+ IRQF_ONESHOT | IRQF_SHARED,
+ dev_name(dev), data);
+ if (ret)
+ return ret;
+
+ ret = devm_mutex_init(dev, &hdata->msg_lock);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, data);
+
+ return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO, nct6694_devs,
+ ARRAY_SIZE(nct6694_devs), NULL, 0, NULL);
+}
+
+static const struct acpi_device_id nct6694_acpi_ids[] = {
+ { "NTN0538", 0 },
+ {}
+};
+
+static struct platform_driver nct6694_driver = {
+ .driver = {
+ .name = DRVNAME,
+ .acpi_match_table = nct6694_acpi_ids,
+ },
+ .probe = nct6694_probe,
+};
+module_platform_driver(nct6694_driver);
+
+MODULE_DESCRIPTION("Nuvoton NCT6694 host-interface transport driver");
+MODULE_AUTHOR("Ming Yu <tmyu0@nuvoton.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/nct6694.c b/drivers/mfd/nct6694.c
index 308b2fda3055..cf3457c2b3ed 100644
--- a/drivers/mfd/nct6694.c
+++ b/drivers/mfd/nct6694.c
@@ -10,8 +10,8 @@
*/
#include <linux/bits.h>
-#include <linux/interrupt.h>
#include <linux/idr.h>
+#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/kernel.h>
@@ -22,6 +22,27 @@
#include <linux/spinlock.h>
#include <linux/usb.h>
+#define NCT6694_VENDOR_ID 0x0416
+#define NCT6694_PRODUCT_ID 0x200B
+#define NCT6694_INT_IN_EP 0x81
+#define NCT6694_BULK_IN_EP 0x02
+#define NCT6694_BULK_OUT_EP 0x03
+
+#define NCT6694_URB_TIMEOUT 1000
+
+union __packed nct6694_usb_msg {
+ struct nct6694_cmd_header cmd_header;
+ struct nct6694_response_header response_header;
+};
+
+struct nct6694_usb_data {
+ struct mutex access_lock;
+ struct urb *int_in_urb;
+ struct usb_device *udev;
+ union nct6694_usb_msg *usb_msg;
+ __le32 *int_buffer;
+};
+
static const struct mfd_cell nct6694_devs[] = {
MFD_CELL_NAME("nct6694-gpio"),
MFD_CELL_NAME("nct6694-gpio"),
@@ -58,7 +79,8 @@ static const struct mfd_cell nct6694_devs[] = {
MFD_CELL_NAME("nct6694-rtc"),
};
-static int nct6694_response_err_handling(struct nct6694 *nct6694, unsigned char err_status)
+static int nct6694_usb_err_handling(struct nct6694 *nct6694,
+ unsigned char err_status)
{
switch (err_status) {
case NCT6694_NO_ERROR:
@@ -83,7 +105,7 @@ static int nct6694_response_err_handling(struct nct6694 *nct6694, unsigned char
}
/**
- * nct6694_read_msg() - Read message from NCT6694 device
+ * nct6694_usb_read_msg() - Read message from NCT6694 device via USB
* @nct6694: NCT6694 device pointer
* @cmd_hd: command header structure
* @buf: buffer to store the response data
@@ -94,13 +116,16 @@ static int nct6694_response_err_handling(struct nct6694 *nct6694, unsigned char
*
* Return: Negative value on error or 0 on success.
*/
-int nct6694_read_msg(struct nct6694 *nct6694, const struct nct6694_cmd_header *cmd_hd, void *buf)
+static int nct6694_usb_read_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf)
{
- union nct6694_usb_msg *msg = nct6694->usb_msg;
- struct usb_device *udev = nct6694->udev;
+ struct nct6694_usb_data *udata = nct6694->priv;
+ union nct6694_usb_msg *msg = udata->usb_msg;
+ struct usb_device *udev = udata->udev;
int tx_len, rx_len, ret;
- guard(mutex)(&nct6694->access_lock);
+ guard(mutex)(&udata->access_lock);
memcpy(&msg->cmd_header, cmd_hd, sizeof(*cmd_hd));
msg->cmd_header.hctrl = NCT6694_HCTRL_GET;
@@ -129,12 +154,11 @@ int nct6694_read_msg(struct nct6694 *nct6694, const struct nct6694_cmd_header *c
return -EIO;
}
- return nct6694_response_err_handling(nct6694, msg->response_header.sts);
+ return nct6694_usb_err_handling(nct6694, msg->response_header.sts);
}
-EXPORT_SYMBOL_GPL(nct6694_read_msg);
/**
- * nct6694_write_msg() - Write message to NCT6694 device
+ * nct6694_usb_write_msg() - Write message to NCT6694 device via USB
* @nct6694: NCT6694 device pointer
* @cmd_hd: command header structure
* @buf: buffer containing the data to be sent
@@ -144,13 +168,16 @@ EXPORT_SYMBOL_GPL(nct6694_read_msg);
*
* Return: Negative value on error or 0 on success.
*/
-int nct6694_write_msg(struct nct6694 *nct6694, const struct nct6694_cmd_header *cmd_hd, void *buf)
+static int nct6694_usb_write_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf)
{
- union nct6694_usb_msg *msg = nct6694->usb_msg;
- struct usb_device *udev = nct6694->udev;
+ struct nct6694_usb_data *udata = nct6694->priv;
+ union nct6694_usb_msg *msg = udata->usb_msg;
+ struct usb_device *udev = udata->udev;
int tx_len, rx_len, ret;
- guard(mutex)(&nct6694->access_lock);
+ guard(mutex)(&udata->access_lock);
memcpy(&msg->cmd_header, cmd_hd, sizeof(*cmd_hd));
msg->cmd_header.hctrl = NCT6694_HCTRL_SET;
@@ -185,9 +212,8 @@ int nct6694_write_msg(struct nct6694 *nct6694, const struct nct6694_cmd_header *
return -EIO;
}
- return nct6694_response_err_handling(nct6694, msg->response_header.sts);
+ return nct6694_usb_err_handling(nct6694, msg->response_header.sts);
}
-EXPORT_SYMBOL_GPL(nct6694_write_msg);
static void usb_int_callback(struct urb *urb)
{
@@ -210,10 +236,12 @@ static void usb_int_callback(struct urb *urb)
int_status = le32_to_cpu(*status_le);
while (int_status) {
- int irq = __ffs(int_status);
+ int hwirq = __ffs(int_status);
+ unsigned int virq = irq_find_mapping(nct6694->domain, hwirq);
- generic_handle_irq_safe(irq_find_mapping(nct6694->domain, irq));
- int_status &= ~BIT(irq);
+ if (virq)
+ generic_handle_irq_safe(virq);
+ int_status &= ~BIT(hwirq);
}
resubmit:
@@ -277,6 +305,7 @@ static int nct6694_usb_probe(struct usb_interface *iface,
struct usb_endpoint_descriptor *int_endpoint;
struct usb_host_interface *interface;
struct device *dev = &iface->dev;
+ struct nct6694_usb_data *udata;
struct nct6694 *nct6694;
int ret;
@@ -284,18 +313,28 @@ static int nct6694_usb_probe(struct usb_interface *iface,
if (!nct6694)
return -ENOMEM;
- nct6694->usb_msg = devm_kzalloc(dev, sizeof(union nct6694_usb_msg), GFP_KERNEL);
- if (!nct6694->usb_msg)
+ udata = devm_kzalloc(dev, sizeof(*udata), GFP_KERNEL);
+ if (!udata)
return -ENOMEM;
- nct6694->int_buffer = devm_kzalloc(dev, sizeof(*nct6694->int_buffer), GFP_KERNEL);
- if (!nct6694->int_buffer)
+ udata->usb_msg = devm_kzalloc(dev, sizeof(*udata->usb_msg), GFP_KERNEL);
+ if (!udata->usb_msg)
return -ENOMEM;
- nct6694->int_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!nct6694->int_in_urb)
+ udata->int_buffer = devm_kzalloc(dev, sizeof(*udata->int_buffer), GFP_KERNEL);
+ if (!udata->int_buffer)
return -ENOMEM;
+ udata->int_in_urb = usb_alloc_urb(0, GFP_KERNEL);
+ if (!udata->int_in_urb)
+ return -ENOMEM;
+
+ udata->udev = udev;
+
+ nct6694->priv = udata;
+ nct6694->read_msg = nct6694_usb_read_msg;
+ nct6694->write_msg = nct6694_usb_write_msg;
+
nct6694->domain = irq_domain_create_simple(NULL, NCT6694_NR_IRQS, 0,
&nct6694_irq_domain_ops,
nct6694);
@@ -305,16 +344,15 @@ static int nct6694_usb_probe(struct usb_interface *iface,
}
nct6694->dev = dev;
- nct6694->udev = udev;
+
+ spin_lock_init(&nct6694->irq_lock);
ida_init(&nct6694->gpio_ida);
ida_init(&nct6694->i2c_ida);
ida_init(&nct6694->canfd_ida);
ida_init(&nct6694->wdt_ida);
- spin_lock_init(&nct6694->irq_lock);
-
- ret = devm_mutex_init(dev, &nct6694->access_lock);
+ ret = devm_mutex_init(dev, &udata->access_lock);
if (ret)
goto err_ida;
@@ -326,11 +364,11 @@ static int nct6694_usb_probe(struct usb_interface *iface,
goto err_ida;
}
- usb_fill_int_urb(nct6694->int_in_urb, udev, usb_rcvintpipe(udev, NCT6694_INT_IN_EP),
- nct6694->int_buffer, sizeof(*nct6694->int_buffer), usb_int_callback,
+ usb_fill_int_urb(udata->int_in_urb, udev, usb_rcvintpipe(udev, NCT6694_INT_IN_EP),
+ udata->int_buffer, sizeof(*udata->int_buffer), usb_int_callback,
nct6694, int_endpoint->bInterval);
- ret = usb_submit_urb(nct6694->int_in_urb, GFP_KERNEL);
+ ret = usb_submit_urb(udata->int_in_urb, GFP_KERNEL);
if (ret)
goto err_ida;
@@ -343,7 +381,7 @@ static int nct6694_usb_probe(struct usb_interface *iface,
return 0;
err_mfd:
- usb_kill_urb(nct6694->int_in_urb);
+ usb_kill_urb(udata->int_in_urb);
err_ida:
ida_destroy(&nct6694->wdt_ida);
ida_destroy(&nct6694->canfd_ida);
@@ -351,22 +389,23 @@ static int nct6694_usb_probe(struct usb_interface *iface,
ida_destroy(&nct6694->gpio_ida);
irq_domain_remove(nct6694->domain);
err_urb:
- usb_free_urb(nct6694->int_in_urb);
+ usb_free_urb(udata->int_in_urb);
return ret;
}
static void nct6694_usb_disconnect(struct usb_interface *iface)
{
struct nct6694 *nct6694 = usb_get_intfdata(iface);
+ struct nct6694_usb_data *udata = nct6694->priv;
mfd_remove_devices(nct6694->dev);
- usb_kill_urb(nct6694->int_in_urb);
+ usb_kill_urb(udata->int_in_urb);
ida_destroy(&nct6694->wdt_ida);
ida_destroy(&nct6694->canfd_ida);
ida_destroy(&nct6694->i2c_ida);
ida_destroy(&nct6694->gpio_ida);
irq_domain_remove(nct6694->domain);
- usb_free_urb(nct6694->int_in_urb);
+ usb_free_urb(udata->int_in_urb);
}
static const struct usb_device_id nct6694_ids[] = {
diff --git a/drivers/net/can/usb/nct6694_canfd.c b/drivers/net/can/usb/nct6694_canfd.c
index e5f7f8849a73..262b4c26c9d4 100644
--- a/drivers/net/can/usb/nct6694_canfd.c
+++ b/drivers/net/can/usb/nct6694_canfd.c
@@ -18,12 +18,6 @@
#define DEVICE_NAME "nct6694-canfd"
-/* USB command module type for NCT6694 CANfd controller.
- * This defines the module type used for communication with the NCT6694
- * CANfd controller over the USB interface.
- */
-#define NCT6694_CANFD_MOD 0x05
-
/* Command 00h - CAN Setting and Initialization */
#define NCT6694_CANFD_SETTING 0x00
#define NCT6694_CANFD_SETTING_ACTIVE_CTRL1 BIT(0)
diff --git a/drivers/rtc/rtc-nct6694.c b/drivers/rtc/rtc-nct6694.c
index 35401a0d9cf5..c06902f150c9 100644
--- a/drivers/rtc/rtc-nct6694.c
+++ b/drivers/rtc/rtc-nct6694.c
@@ -14,13 +14,6 @@
#include <linux/rtc.h>
#include <linux/slab.h>
-/*
- * USB command module type for NCT6694 RTC controller.
- * This defines the module type used for communication with the NCT6694
- * RTC controller over the USB interface.
- */
-#define NCT6694_RTC_MOD 0x08
-
/* Command 00h - RTC Time */
#define NCT6694_RTC_TIME 0x0000
#define NCT6694_RTC_TIME_SEL 0x00
diff --git a/drivers/watchdog/nct6694_wdt.c b/drivers/watchdog/nct6694_wdt.c
index bc3689bd4b6b..4c06ac105562 100644
--- a/drivers/watchdog/nct6694_wdt.c
+++ b/drivers/watchdog/nct6694_wdt.c
@@ -20,13 +20,6 @@
#define NCT6694_WDT_MAX_DEVS 2
-/*
- * USB command module type for NCT6694 WDT controller.
- * This defines the module type used for communication with the NCT6694
- * WDT controller over the USB interface.
- */
-#define NCT6694_WDT_MOD 0x07
-
/* Command 00h - WDT Setup */
#define NCT6694_WDT_SETUP 0x00
#define NCT6694_WDT_SETUP_SEL(idx) (idx ? 0x01 : 0x00)
diff --git a/include/linux/mfd/nct6694.h b/include/linux/mfd/nct6694.h
index 6eb9be2cd4a0..fd645bf20fcd 100644
--- a/include/linux/mfd/nct6694.h
+++ b/include/linux/mfd/nct6694.h
@@ -2,22 +2,29 @@
/*
* Copyright (C) 2025 Nuvoton Technology Corp.
*
- * Nuvoton NCT6694 USB transaction and data structure.
+ * Nuvoton NCT6694 core definitions shared by all transport drivers
+ * and sub-device drivers.
*/
#ifndef __MFD_NCT6694_H
#define __MFD_NCT6694_H
-#define NCT6694_VENDOR_ID 0x0416
-#define NCT6694_PRODUCT_ID 0x200B
-#define NCT6694_INT_IN_EP 0x81
-#define NCT6694_BULK_IN_EP 0x02
-#define NCT6694_BULK_OUT_EP 0x03
+#include <linux/idr.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
#define NCT6694_HCTRL_SET 0x40
#define NCT6694_HCTRL_GET 0x80
-#define NCT6694_URB_TIMEOUT 1000
+#define NCT6694_HWMON_MOD 0x00
+#define NCT6694_PWM_MOD 0x01
+#define NCT6694_I2C_MOD 0x03
+#define NCT6694_CANFD_MOD 0x05
+#define NCT6694_WDT_MOD 0x07
+#define NCT6694_RTC_MOD 0x08
+#define NCT6694_RPT_MOD 0xFF
+#define NCT6694_GPIO_MOD NCT6694_RPT_MOD
enum nct6694_irq_id {
NCT6694_IRQ_GPIO0 = 0,
@@ -75,11 +82,6 @@ struct __packed nct6694_response_header {
__le16 len;
};
-union __packed nct6694_usb_msg {
- struct nct6694_cmd_header cmd_header;
- struct nct6694_response_header response_header;
-};
-
struct nct6694 {
struct device *dev;
struct ida gpio_ida;
@@ -87,16 +89,30 @@ struct nct6694 {
struct ida canfd_ida;
struct ida wdt_ida;
struct irq_domain *domain;
- struct mutex access_lock;
spinlock_t irq_lock;
- struct urb *int_in_urb;
- struct usb_device *udev;
- union nct6694_usb_msg *usb_msg;
- __le32 *int_buffer;
unsigned int irq_enable;
+
+ void *priv;
+ int (*read_msg)(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf);
+ int (*write_msg)(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf);
};
-int nct6694_read_msg(struct nct6694 *nct6694, const struct nct6694_cmd_header *cmd_hd, void *buf);
-int nct6694_write_msg(struct nct6694 *nct6694, const struct nct6694_cmd_header *cmd_hd, void *buf);
+static inline int nct6694_read_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf)
+{
+ return nct6694->read_msg(nct6694, cmd_hd, buf);
+}
+
+static inline int nct6694_write_msg(struct nct6694 *nct6694,
+ const struct nct6694_cmd_header *cmd_hd,
+ void *buf)
+{
+ return nct6694->write_msg(nct6694, cmd_hd, buf);
+}
#endif
--
2.34.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox