From: Kukjin Kim <kgene.kim@samsung.com>
To: 'Jingoo Han' <jg1.han@samsung.com>, linux-samsung-soc@vger.kernel.org
Subject: RE: [PATCH] ARM: EXYNOS: Use gpio_request_one
Date: Wed, 21 Dec 2011 13:18:06 +0900 [thread overview]
Message-ID: <061f01ccbf97$8a4eaac0$9eec0040$%kim@samsung.com> (raw)
In-Reply-To: <003d01ccb876$ccffa720$66fef560$%han@samsung.com>
Jingoo Han wrote:
>
> By using gpio_request_one it is possible to set the direction
> and initial value in one shot. Thus, using gpio_request_one can
> make the code simpler.
>
> Signed-off-by: Jingoo Han <jg1.han@samsung.com>
> ---
> arch/arm/mach-exynos/mach-nuri.c | 4 +---
> arch/arm/mach-exynos/mach-smdkv310.c | 4 +---
> arch/arm/mach-exynos/mach-universal_c210.c | 10 +++-------
> 3 files changed, 5 insertions(+), 13 deletions(-)
>
> diff --git a/arch/arm/mach-exynos/mach-nuri.c b/arch/arm/mach-exynos/mach-
> nuri.c
> index 236bbe1..c96de1f 100644
> --- a/arch/arm/mach-exynos/mach-nuri.c
> +++ b/arch/arm/mach-exynos/mach-nuri.c
> @@ -249,9 +249,7 @@ static int nuri_bl_init(struct device *dev)
> {
> int ret, gpio = EXYNOS4_GPE2(3);
>
> - ret = gpio_request(gpio, "LCD_LDO_EN");
> - if (!ret)
> - gpio_direction_output(gpio, 0);
> + ret = gpio_request_one(gpio, GPIOF_OUT_INIT_LOW, "LCD_LD0_EN");
>
Looks good, but following is better?
static int nuri_bl_init(struct device *dev)
{
- int ret, gpio = EXYNOS4_GPE2(3);
-
- ret = gpio_request(gpio, "LCD_LDO_EN");
- if (!ret)
- gpio_direction_output(gpio, 0);
-
- return ret;
+ return gpio_request_one(EXYNOS4_GPE2(3), GPIOF_OUT_INIT_LOW,
"LCD_LDO_EN");
}
Others, ok to me.
Could you please re-send?
Thanks.
Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.
> return ret;
> }
> diff --git a/arch/arm/mach-exynos/mach-smdkv310.c b/arch/arm/mach-
> exynos/mach-smdkv310.c
> index cec2afa..cbf31bd 100644
> --- a/arch/arm/mach-exynos/mach-smdkv310.c
> +++ b/arch/arm/mach-exynos/mach-smdkv310.c
> @@ -129,9 +129,7 @@ static void lcd_lte480wv_set_power(struct
> plat_lcd_data *pd,
> gpio_free(EXYNOS4_GPD0(1));
> #endif
> /* fire nRESET on power up */
> - gpio_request(EXYNOS4_GPX0(6), "GPX0");
> -
> - gpio_direction_output(EXYNOS4_GPX0(6), 1);
> + gpio_request_one(EXYNOS4_GPX0(6), GPIOF_OUT_INIT_HIGH,
> "GPX0");
> mdelay(100);
>
> gpio_set_value(EXYNOS4_GPX0(6), 0);
> diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-
> exynos/mach-universal_c210.c
> index a2a177f..0a04cd6 100644
> --- a/arch/arm/mach-exynos/mach-universal_c210.c
> +++ b/arch/arm/mach-exynos/mach-universal_c210.c
> @@ -608,8 +608,7 @@ static void __init universal_tsp_init(void)
>
> /* TSP_LDO_ON: XMDMADDR_11 */
> gpio = EXYNOS4_GPE2(3);
> - gpio_request(gpio, "TSP_LDO_ON");
> - gpio_direction_output(gpio, 1);
> + gpio_request_one(gpio, GPIOF_OUT_INIT_HIGH, "TSP_LDO_ON");
> gpio_export(gpio, 0);
>
> /* TSP_INT: XMDMADDR_7 */
> @@ -669,8 +668,7 @@ static void __init universal_touchkey_init(void)
> i2c_gpio12_devs[0].irq = gpio_to_irq(gpio);
>
> gpio = EXYNOS4_GPE3(3); /* XMDMDATA_3 */
> - gpio_request(gpio, "3_TOUCH_EN");
> - gpio_direction_output(gpio, 1);
> + gpio_request_one(gpio, GPIOF_OUT_INIT_HIGH, "3_TOUCH_EN");
> }
>
> static struct s3c2410_platform_i2c universal_i2c0_platdata __initdata = {
> @@ -1000,9 +998,7 @@ static void __init universal_map_io(void)
> void s5p_tv_setup(void)
> {
> /* direct HPD to HDMI chip */
> - gpio_request(EXYNOS4_GPX3(7), "hpd-plug");
> -
> - gpio_direction_input(EXYNOS4_GPX3(7));
> + gpio_request_one(EXYNOS4_GPX3(7), GPIOF_IN, "hpd-plug");
> s3c_gpio_cfgpin(EXYNOS4_GPX3(7), S3C_GPIO_SFN(0x3));
> s3c_gpio_setpull(EXYNOS4_GPX3(7), S3C_GPIO_PULL_NONE);
>
> --
> 1.7.1
next prev parent reply other threads:[~2011-12-21 4:18 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-12-12 2:36 [PATCH] ARM: EXYNOS: Use gpio_request_one Jingoo Han
2011-12-21 4:18 ` Kukjin Kim [this message]
2011-12-21 5:26 ` Jingoo Han
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='061f01ccbf97$8a4eaac0$9eec0040$%kim@samsung.com' \
--to=kgene.kim@samsung.com \
--cc=jg1.han@samsung.com \
--cc=linux-samsung-soc@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox