From: Lee Jones <lee.jones@linaro.org>
To: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Sangbeom Kim <sbkim73@samsung.com>,
Samuel Ortiz <sameo@linux.intel.com>,
linux-kernel@vger.kernel.org, linux-samsung-soc@vger.kernel.org,
Kyungmin Park <kyungmin.park@samsung.com>,
Marek Szyprowski <m.szyprowski@samsung.com>,
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>,
Chanwoo Choi <cw00.choi@samsung.com>,
Mark Brown <broonie@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>
Subject: Re: [PATCH v2 11/14] regulator: s2mps11: Add opmode for S2MPS14 regulators
Date: Thu, 13 Feb 2014 12:43:20 +0000 [thread overview]
Message-ID: <20140213124320.GB3403@lee--X1> (raw)
In-Reply-To: <1392282847-25444-12-git-send-email-k.kozlowski@samsung.com>
> S2MPS11/S2MPS14 regulators support different modes of operation:
> - Always off;
> - On/Off controlled by pin/GPIO (PWREN/LDOEN/EMMCEN);
> - Always on;
> This is very similar to S5M8767 regulator driver which also supports
> opmodes (although S5M8767 have also low-power mode).
>
> This patch adds parsing the operation mode from DTS by reading a
> "op_mode" property from regulator child node.
>
> The op_mode is then used for enabling the S2MPS14 regulators.
> On S2MPS11 the DTS "op_mode" property is parsed but not used for
> enabling, as this was not tested.
>
> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Cc: Mark Brown <broonie@kernel.org>
> Cc: Liam Girdwood <lgirdwood@gmail.com>
> ---
> drivers/regulator/s2mps11.c | 97 ++++++++++++++++++++++++++++++++++-
> include/linux/mfd/samsung/s2mps14.h | 19 +++++++
> 2 files changed, 115 insertions(+), 1 deletion(-)
<snip>
> +++ b/include/linux/mfd/samsung/s2mps14.h
> @@ -149,4 +149,23 @@ enum s2mps14_regulators {
> #define S2MPS14_LDO_N_VOLTAGES (S2MPS14_LDO_VSEL_MASK + 1)
> #define S2MPS14_BUCK_N_VOLTAGES (S2MPS14_BUCK_VSEL_MASK + 1)
>
> +#define S2MPS14_ENCTRL_SHIFT 6
> +#define S2MPS14_ENCTRL_MASK (0x3 << S2MPS14_ENCTRL_SHIFT)
> +
> +/*
> + * Values of regulator operation modes match device tree bindings.
> + */
> +enum s2mps14_regulator_opmode {
> + S2MPS14_REGULATOR_OPMODE_OFF = 0,
> + S2MPS14_REGULATOR_OPMODE_ON = 1,
> + /*
> + * Reserved for compatibility with S5M8767 where this
> + * is a low power mode.
> + */
> + S2MPS14_REGULATOR_OPMODE_RESERVED = 2,
> + S2MPS14_REGULATOR_OPMODE_SUSPEND = 3,
You don't need to number these like this. If you want to force the
numbering to start at '0' initialise the top value, then the rest
should be sequential.
> + S2MPS14_REGULATOR_OPMODE_MAX,
> +};
> +
> #endif /* __LINUX_MFD_S2MPS14_H */
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2014-02-13 12:43 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-13 9:13 [PATCH v2 00/14] mfd/regulator/rtc: sec: Add support for S2MPS14 Krzysztof Kozlowski
2014-02-13 9:13 ` [PATCH v2 01/14] mfd: sec: Add maximum RTC register for regmap config Krzysztof Kozlowski
2014-02-13 9:13 ` [PATCH v2 02/14] mfd: sec: Select different RTC regmaps for devices Krzysztof Kozlowski
2014-02-13 9:13 ` [PATCH v2 03/14] mfd/rtc: sec/s5m: Rename SEC* symbols to S5M Krzysztof Kozlowski
2014-02-13 10:11 ` Lee Jones
2014-02-13 9:13 ` [PATCH v2 04/14] rtc: s5m: Remove undocumented time init on first boot Krzysztof Kozlowski
2014-02-13 9:13 ` [PATCH v2 05/14] mfd: sec: Use consistent S2MPS11 RTC alarm interrupt indexes Krzysztof Kozlowski
2014-02-13 9:13 ` [PATCH v2 06/14] regulator: s2mps11: Constify regulator_desc array Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 07/14] regulator: s2mps11: Copy supported regulators from initconst Krzysztof Kozlowski
2014-02-13 12:21 ` Yadwinder Singh Brar
2014-02-13 12:35 ` Krzysztof Kozlowski
2014-02-13 12:37 ` [PATCH " Krzysztof Kozlowski
2014-02-13 18:05 ` Mark Brown
2014-02-13 19:07 ` [PATCH v2 " Mark Brown
2014-02-14 7:46 ` Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 08/14] mfd: sec: Add support for S2MPS14 Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 09/14] regulator: s2mps11: Add support for S2MPS14 regulators Krzysztof Kozlowski
2014-02-13 12:24 ` Yadwinder Singh Brar
2014-02-13 19:10 ` Mark Brown
2014-02-14 7:33 ` Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 10/14] Documentation: mfd: s2mps11: Document support for S2MPS14 Krzysztof Kozlowski
2014-02-13 14:55 ` Tomasz Figa
2014-02-13 9:14 ` [PATCH v2 11/14] regulator: s2mps11: Add opmode for S2MPS14 regulators Krzysztof Kozlowski
2014-02-13 12:16 ` Yadwinder Singh Brar
2014-02-14 13:05 ` Krzysztof Kozlowski
2014-02-14 21:05 ` Mark Brown
2014-02-17 8:07 ` Krzysztof Kozlowski
2014-02-18 0:35 ` Mark Brown
2014-02-18 8:12 ` Krzysztof Kozlowski
2014-02-19 4:08 ` Mark Brown
2014-02-19 10:09 ` Krzysztof Kozlowski
2014-02-19 12:16 ` Mark Brown
2014-02-19 14:19 ` Krzysztof Kozlowski
2014-02-19 15:07 ` Mark Brown
2014-02-13 12:43 ` Lee Jones [this message]
2014-02-13 13:00 ` Krzysztof Kozlowski
2014-02-13 19:28 ` Mark Brown
2014-02-14 8:15 ` Krzysztof Kozlowski
2014-02-14 20:59 ` Mark Brown
2014-02-17 8:09 ` Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 12/14] Documentation: mfd/regulator: s2mps11: Document the "op_mode" bindings Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 13/14] rtc: s5m: Support different register layout Krzysztof Kozlowski
2014-02-13 9:14 ` [PATCH v2 14/14] rtc: s5m: Add support for S2MPS14 RTC Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140213124320.GB3403@lee--X1 \
--to=lee.jones@linaro.org \
--cc=b.zolnierkie@samsung.com \
--cc=broonie@kernel.org \
--cc=cw00.choi@samsung.com \
--cc=k.kozlowski@samsung.com \
--cc=kyungmin.park@samsung.com \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
--cc=sameo@linux.intel.com \
--cc=sbkim73@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox