Re: [PATCH v3 3/3] spi: s3c64xx: support interrupt based pio mode

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 02/05/2023 08:28, Jaewon Kim wrote:
> Support interrupt based pio mode to optimize cpu usage.
> When transmitting data size is larget than 32 bytes, operates with
> interrupt based pio mode.
> 
> By using the FIFORDY INT, an interrupt can be triggered when
> the desired size of data has been received. Using this, we can support
> interrupt based pio mode.
> 
> Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
> ---
>  drivers/spi/spi-s3c64xx.c | 66 ++++++++++++++++++++++++++++++++++-----
>  1 file changed, 58 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
> index 2a8304678df9..323c6da9730b 100644
> --- a/drivers/spi/spi-s3c64xx.c
> +++ b/drivers/spi/spi-s3c64xx.c
> @@ -58,6 +58,8 @@
>  #define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD	(1<<17)
>  #define S3C64XX_SPI_MODE_BUS_TSZ_WORD		(2<<17)
>  #define S3C64XX_SPI_MODE_BUS_TSZ_MASK		(3<<17)
> +#define S3C64XX_SPI_MODE_RX_RDY_LVL		GENMASK(16, 11)
> +#define S3C64XX_SPI_MODE_RX_RDY_LVL_SHIFT	11
>  #define S3C64XX_SPI_MODE_SELF_LOOPBACK		(1<<3)
>  #define S3C64XX_SPI_MODE_RXDMA_ON		(1<<2)
>  #define S3C64XX_SPI_MODE_TXDMA_ON		(1<<1)
> @@ -114,6 +116,8 @@
>  
>  #define S3C64XX_SPI_TRAILCNT		S3C64XX_SPI_MAX_TRAILCNT
>  
> +#define S3C64XX_SPI_POLLING_SIZE	32
> +
>  #define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
>  #define is_polling(x)	(x->cntrlr_info->polling)
>  
> @@ -552,7 +556,7 @@ static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
>  }
>  
>  static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
> -				struct spi_transfer *xfer)
> +				struct spi_transfer *xfer, bool use_irq)
>  {
>  	void __iomem *regs = sdd->regs;
>  	unsigned long val;
> @@ -573,6 +577,12 @@ static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
>  	if (RX_FIFO_LVL(status, sdd) < xfer->len)
>  		usleep_range(time_us / 2, time_us);
>  
> +	if (use_irq) {
> +		val = msecs_to_jiffies(ms);
> +		if (!wait_for_completion_timeout(&sdd->xfer_completion, val))
> +			return -EIO;
> +	}
> +
>  	val = msecs_to_loops(ms);
>  	do {
>  		status = readl(regs + S3C64XX_SPI_STATUS);
> @@ -735,10 +745,13 @@ static int s3c64xx_spi_transfer_one(struct spi_master *master,
>  	void *rx_buf = NULL;
>  	int target_len = 0, origin_len = 0;
>  	int use_dma = 0;
> +	bool use_irq = false;
>  	int status;
>  	u32 speed;
>  	u8 bpw;
>  	unsigned long flags;
> +	u32 rdy_lv;
> +	u32 val;
>  
>  	reinit_completion(&sdd->xfer_completion);
>  
> @@ -759,17 +772,46 @@ static int s3c64xx_spi_transfer_one(struct spi_master *master,
>  	    sdd->rx_dma.ch && sdd->tx_dma.ch) {
>  		use_dma = 1;
>  
> -	} else if (xfer->len > fifo_len) {
> +	} else if (xfer->len >= fifo_len) {

I don't fully understand this. If len equals to fifo_len, everything
would fit into FIFO so no need for all this?

>  		tx_buf = xfer->tx_buf;
>  		rx_buf = xfer->rx_buf;
>  		origin_len = xfer->len;
> -
>  		target_len = xfer->len;
> -		if (xfer->len > fifo_len)
> -			xfer->len = fifo_len;
> +		xfer->len = fifo_len - 1;
>  	}
>  
>  	do {
> +		/* transfer size is greater than 32, change to IRQ mode */
> +		if (xfer->len > S3C64XX_SPI_POLLING_SIZE)
> +			use_irq = true;
> +
> +		if (use_irq) {
> +			reinit_completion(&sdd->xfer_completion);
> +
> +			rdy_lv = xfer->len;

Style is:

/*
 *

> +			/* Setup RDY_FIFO trigger Level
> +			 * RDY_LVL =
> +			 * fifo_lvl up to 64 byte -> N bytes
> +			 *               128 byte -> RDY_LVL * 2 bytes
> +			 *               256 byte -> RDY_LVL * 4 bytes

I don't understand it. Based on this equation for 256 bytes,
RDY_LVL = RDY_LVL * 4?
Didn't you mean xfer->len?


Best regards,
Krzysztof