U-Boot 2013.04-gb98ed09 (Mar 07 2014 - 12:25:37) for Peach CPU: Exynos5420@1800MHz Board: Google Peach Pit, rev 9.0 I2C: ready DRAM: 2 GiB PMIC max77802-pmic initialized CPU: Exynos5420@1800MHz TPS65090 PMIC EC init MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 SF: Detected W25Q32DW with page size 4 KiB, total 32 MiB In: cros-ec-keyb Out: lcd Err: lcd SF: Detected W25Q32DW with page size 4 KiB, total 32 MiB ELOG: Event(17) added with size 13 Net: No ethernet found. Hit any key to stop autoboot: 0 reading uImage 3336553 bytes read in 163 ms (19.5 MiB/s) ## Booting kernel from Legacy Image at 42000000 ... Image Name: Linux Created: 2014-11-24 8:30:31 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3336489 Bytes = 3.2 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Timer summary in microseconds: Mark Elapsed Stage 0 0 reset 3,471,164 3,471,164 board_init_f 3,567,283 96,119 board_init_r 3,712,040 144,757 id=64 3,714,761 2,721 main_loop 4,063,547 348,786 bootm_start 4,063,549 2 id=1 4,069,252 5,703 id=2 4,069,254 2 id=3 4,123,769 54,515 id=4 4,123,770 1 id=5 4,123,772 2 id=6 4,123,773 1 id=14 4,225,455 101,682 id=7 4,225,465 10 id=15 4,229,519 4,054 start_kernel Accumulated time: 6,956 SPI read cleanup_before_linux_select: Console recording failed (1) [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.18.0-rc5-next-20141121 (javier@minerva) (gcc vers ion 4.6.3 (Debian 4.6.3-14) ) #87 SMP PREEMPT Mon Nov 24 09:09:36 CET 2014 [ 0.000000] CPU: ARMv7 Processor [412fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: Google Peach Pit Rev 6+ [ 0.000000] Ignoring memory range 0x20000000 - 0x40000000 [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 393216 [ 0.000000] free_area_init_node: node 0, pgdat c067a000, node_mem_map eebf600 0 [ 0.000000] Normal zone: 1520 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 1552 pages used for memmap [ 0.000000] HighMem zone: 198656 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 9 pages/cpu @eeb7e000 s7616 r8192 d21056 u36864 [ 0.000000] pcpu-alloc: s7616 r8192 d21056 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 391696 [ 0.000000] Kernel command line: console=ttySAC3,115200N8 debug earlyprintk r oot=/dev/mmcblk1p2 rootwait rw no_console_suspend [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1486972K/1572864K available (4400K kernel code, 218K rwda ta, 1504K rodata, 300K init, 284K bss, 20356K reserved, 65536K cma-reserved, 729 088K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc05cc5b8 (5906 kB) [ 0.000000] .init : 0xc05cd000 - 0xc0618000 ( 300 kB) [ 0.000000] .data : 0xc0618000 - 0xc064e940 ( 219 kB) [ 0.000000] .bss : 0xc064e940 - 0xc0695a44 ( 285 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] GIC physical location is 0x10481000 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000003] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 17895 6969942ns [ 0.000215] Console: colour dummy device 80x30 [ 0.000231] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=120000) [ 0.000240] pid_max: default: 32768 minimum: 301 [ 0.000340] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000347] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000731] CPU: Testing write buffer coherency: ok [ 0.000938] CPU0: update cpu_capacity 1535 [ 0.000945] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001042] Setting up static identity map for 0x4042c780 - 0x4042c7d8 [ 0.001198] ARM CCI driver probed [ 0.001615] Exynos MCPM support installed [ 0.030221] CPU1: Booted secondary processor [ 0.030256] CPU1: update cpu_capacity 1535 [ 0.030260] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.040219] CPU2: Booted secondary processor [ 0.040245] CPU2: update cpu_capacity 1535 [ 0.040248] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.050208] CPU3: Booted secondary processor [ 0.050233] CPU3: update cpu_capacity 1535 [ 0.050237] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.060245] CPU4: Booted secondary processor [ 0.060344] CPU4: update cpu_capacity 448 [ 0.060355] CPU4: thread -1, cpu 0, socket 1, mpidr 80000100 [ 0.070236] CPU5: Booted secondary processor [ 0.070298] CPU5: update cpu_capacity 448 [ 0.070307] CPU5: thread -1, cpu 1, socket 1, mpidr 80000101 [ 0.080243] CPU6: Booted secondary processor [ 0.080305] CPU6: update cpu_capacity 448 [ 0.080314] CPU6: thread -1, cpu 2, socket 1, mpidr 80000102 [ 0.090237] CPU7: Booted secondary processor [ 0.090300] CPU7: update cpu_capacity 448 [ 0.090310] CPU7: thread -1, cpu 3, socket 1, mpidr 80000103 [ 0.090387] Brought up 8 CPUs [ 0.090419] SMP: Total of 8 processors activated. [ 0.090425] CPU: All CPU(s) started in SVC mode. [ 0.090902] devtmpfs: initialized [ 0.096013] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.097714] pinctrl core: initialized pinctrl subsystem [ 0.112040] NET: Registered protocol family 16 [ 0.113045] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.117023] gpiochip_add: registered GPIOs 0 to 7 on device: gpy7 [ 0.117033] gpiochip_add: registered GPIOs 8 to 15 on device: gpx0 [ 0.117041] gpiochip_add: registered GPIOs 16 to 23 on device: gpx1 [ 0.117049] gpiochip_add: registered GPIOs 24 to 31 on device: gpx2 [ 0.117057] gpiochip_add: registered GPIOs 32 to 39 on device: gpx3 [ 0.117854] gpiochip_add: registered GPIOs 40 to 47 on device: gpc0 [ 0.117863] gpiochip_add: registered GPIOs 48 to 55 on device: gpc1 [ 0.117871] gpiochip_add: registered GPIOs 56 to 62 on device: gpc2 [ 0.117879] gpiochip_add: registered GPIOs 63 to 66 on device: gpc3 [ 0.117886] gpiochip_add: registered GPIOs 67 to 68 on device: gpc4 [ 0.117894] gpiochip_add: registered GPIOs 69 to 76 on device: gpd1 [ 0.117901] gpiochip_add: registered GPIOs 77 to 82 on device: gpy0 [ 0.117909] gpiochip_add: registered GPIOs 83 to 86 on device: gpy1 [ 0.117916] gpiochip_add: registered GPIOs 87 to 92 on device: gpy2 [ 0.117924] gpiochip_add: registered GPIOs 93 to 100 on device: gpy3 [ 0.117931] gpiochip_add: registered GPIOs 101 to 108 on device: gpy4 [ 0.117939] gpiochip_add: registered GPIOs 109 to 116 on device: gpy5 [ 0.117946] gpiochip_add: registered GPIOs 117 to 124 on device: gpy6 [ 0.118471] gpiochip_add: registered GPIOs 125 to 132 on device: gpe0 [ 0.118479] gpiochip_add: registered GPIOs 133 to 134 on device: gpe1 [ 0.118487] gpiochip_add: registered GPIOs 135 to 140 on device: gpf0 [ 0.118495] gpiochip_add: registered GPIOs 141 to 148 on device: gpf1 [ 0.118502] gpiochip_add: registered GPIOs 149 to 156 on device: gpg0 [ 0.118510] gpiochip_add: registered GPIOs 157 to 164 on device: gpg1 [ 0.118517] gpiochip_add: registered GPIOs 165 to 166 on device: gpg2 [ 0.118525] gpiochip_add: registered GPIOs 167 to 170 on device: gpj4 [ 0.119033] gpiochip_add: registered GPIOs 171 to 178 on device: gpa0 [ 0.119042] gpiochip_add: registered GPIOs 179 to 184 on device: gpa1 [ 0.119050] gpiochip_add: registered GPIOs 185 to 192 on device: gpa2 [ 0.119057] gpiochip_add: registered GPIOs 193 to 197 on device: gpb0 [ 0.119065] gpiochip_add: registered GPIOs 198 to 202 on device: gpb1 [ 0.119073] gpiochip_add: registered GPIOs 203 to 206 on device: gpb2 [ 0.119080] gpiochip_add: registered GPIOs 207 to 214 on device: gpb3 [ 0.119088] gpiochip_add: registered GPIOs 215 to 216 on device: gpb4 [ 0.119095] gpiochip_add: registered GPIOs 217 to 224 on device: gph0 [ 0.119676] gpiochip_add: registered GPIOs 225 to 231 on device: gpz [ 0.120916] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 0.126679] EXYNOS5420 PMU initialized [ 0.156211] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regula tor-usb300[0]' - status (0) [ 0.156509] of_get_named_gpiod_flags: parsed 'gpio' property of node '/regula tor-usb301[0]' - status (0) [ 0.156767] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/f ixed-regulator[0]' [ 0.158409] SCSI subsystem initialized [ 0.158841] usbcore: registered new interface driver usbfs [ 0.158941] usbcore: registered new interface driver hub [ 0.159093] usbcore: registered new device driver usb [ 0.159672] s3c-i2c 12c80000.i2c: slave address 0x50 [ 0.159684] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz [ 0.159870] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter [ 0.162807] Advanced Linux Sound Architecture Driver Initialized. [ 0.163569] Switched to clocksource mct-frc [ 0.176514] NET: Registered protocol family 2 [ 0.176937] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.176994] TCP bind hash table entries: 8192 (order: 5, 163840 bytes) [ 0.177086] TCP: Hash tables configured (established 8192 bind 8192) [ 0.177126] TCP: reno registered [ 0.177137] UDP hash table entries: 512 (order: 2, 24576 bytes) [ 0.177161] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes) [ 0.177327] NET: Registered protocol family 1 [ 0.179529] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.192419] romfs: ROMFS MTD (C) 2007 Red Hat, Inc. [ 0.193042] bounce: pool size: 64 pages [ 0.193054] io scheduler noop registered [ 0.193063] io scheduler deadline registered [ 0.193477] io scheduler cfq registered (default) [ 0.193698] exynos-dp-video-phy 10040728.video-phy: Failed to lookup PMU regm ap [ 0.193946] exynos-mipi-video-phy 10040714.video-phy: can't request region fo r resource [mem 0x10040714-0x1004071f] [ 0.193963] exynos-mipi-video-phy: probe of 10040714.video-phy failed with er ror -16 [ 0.198698] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330 [ 0.198708] dma-pl330 3880000.adma: DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 N um_Events-6 [ 0.202828] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 0.202837] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_ Peri-32 Num_Events-32 [ 0.206913] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 0.206923] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_ Peri-32 Num_Events-32 [ 0.208044] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 0.208053] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_ Peri-1 Num_Events-32 [ 0.311556] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.313006] samsung-uart 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 8 3, base_baud = 0) is a S3C6400/10 [ 0.313353] samsung-uart 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 8 4, base_baud = 0) is a S3C6400/10 [ 0.313737] samsung-uart 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 8 5, base_baud = 0) is a S3C6400/10 [ 0.314079] samsung-uart 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 8 6, base_baud = 0) is a S3C6400/10 [ 1.285505] console [ttySAC3] enabled [ 1.290414] error detecting cacheinfo..cpu0 [ 1.300324] brd: module loaded [ 1.305533] loop: module loaded [ 1.307769] of_get_named_gpiod_flags: parsed 'cs-gpios' property of node '/sp i@12d40000[0]' - status (0) [ 1.317550] cros-ec-spi spi2.0: Chrome EC device registered [ 1.322624] usbcore: registered new interface driver asix [ 1.327708] usbcore: registered new interface driver ax88179_178a [ 1.333717] usbcore: registered new interface driver cdc_ether [ 1.339554] usbcore: registered new interface driver smsc75xx [ 1.345469] usbcore: registered new interface driver smsc95xx [ 1.351085] usbcore: registered new interface driver net1080 [ 1.356671] usbcore: registered new interface driver cdc_subset [ 1.362516] usbcore: registered new interface driver zaurus [ 1.368106] usbcore: registered new interface driver cdc_ncm [ 1.374271] usb@12000000 supply vdd33 not found, using dummy regulator [ 1.380223] usb@12000000 supply vdd10 not found, using dummy regulator [ 1.788070] usb@12400000 supply vdd33 not found, using dummy regulator [ 1.793174] usb@12400000 supply vdd10 not found, using dummy regulator [ 2.200906] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 2.204947] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus nu mber 1 [ 2.212818] xhci-hcd xhci-hcd.2.auto: irq 104, io mem 0x12000000 [ 2.218705] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.225314] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.232513] usb usb1: Product: xHCI Host Controller [ 2.237370] usb usb1: Manufacturer: Linux 3.18.0-rc5-next-20141121 xhci-hcd [ 2.244311] usb usb1: SerialNumber: xhci-hcd.2.auto [ 2.249760] hub 1-0:1.0: USB hub found [ 2.252902] hub 1-0:1.0: 1 port detected [ 2.257145] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 2.262278] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus nu mber 2 [ 2.270050] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 2.276667] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.283867] usb usb2: Product: xHCI Host Controller [ 2.288724] usb usb2: Manufacturer: Linux 3.18.0-rc5-next-20141121 xhci-hcd [ 2.295663] usb usb2: SerialNumber: xhci-hcd.2.auto [ 2.301072] hub 2-0:1.0: USB hub found [ 2.304272] hub 2-0:1.0: 1 port detected [ 2.308530] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller [ 2.313642] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus nu mber 3 [ 2.321518] xhci-hcd xhci-hcd.5.auto: irq 105, io mem 0x12400000 [ 2.327360] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.334010] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.341207] usb usb3: Product: xHCI Host Controller [ 2.346065] usb usb3: Manufacturer: Linux 3.18.0-rc5-next-20141121 xhci-hcd [ 2.353005] usb usb3: SerialNumber: xhci-hcd.5.auto [ 2.358476] hub 3-0:1.0: USB hub found [ 2.361617] hub 3-0:1.0: 1 port detected [ 2.365839] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller [ 2.370979] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus nu mber 4 [ 2.378742] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 2.385368] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.392566] usb usb4: Product: xHCI Host Controller [ 2.397424] usb usb4: Manufacturer: Linux 3.18.0-rc5-next-20141121 xhci-hcd [ 2.404456] usb usb4: SerialNumber: xhci-hcd.5.auto [ 2.409779] hub 4-0:1.0: USB hub found [ 2.412953] hub 4-0:1.0: 1 port detected [ 2.417236] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.423366] ehci-exynos: EHCI EXYNOS driver [ 2.427669] of_get_named_gpiod_flags: can't parse 'samsung,vbus-gpio' propert y of node '/usb@12110000[0]' [ 2.437249] exynos-ehci 12110000.usb: EHCI Host Controller [ 2.442554] exynos-ehci 12110000.usb: new USB bus registered, assigned bus nu mber 5 [ 2.450278] exynos-ehci 12110000.usb: irq 103, io mem 0x12110000 [ 2.463601] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 2.468245] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.474924] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.482109] usb usb5: Product: EHCI Host Controller [ 2.486966] usb usb5: Manufacturer: Linux 3.18.0-rc5-next-20141121 ehci_hcd [ 2.493925] usb usb5: SerialNumber: 12110000.usb [ 2.499062] hub 5-0:1.0: USB hub found [ 2.502236] hub 5-0:1.0: 3 ports detected [ 2.506818] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.512413] ohci-exynos: OHCI EXYNOS driver [ 2.516819] exynos-ohci 12120000.usb: USB Host Controller [ 2.521945] exynos-ohci 12120000.usb: new USB bus registered, assigned bus nu mber 6 [ 2.529639] exynos-ohci 12120000.usb: irq 103, io mem 0x12120000 [ 2.592724] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.598043] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.606177] usb usb6: Product: USB Host Controller [ 2.610014] usb usb6: Manufacturer: Linux 3.18.0-rc5-next-20141121 ohci_hcd [ 2.616952] usb usb6: SerialNumber: 12120000.usb [ 2.622079] hub 6-0:1.0: USB hub found [ 2.625303] hub 6-0:1.0: 3 ports detected [ 2.629912] usbcore: registered new interface driver usb-storage [ 2.635746] mousedev: PS/2 mouse device common for all mice [ 2.641231] input: cros-ec-spi as /devices/platform/12d40000.spi/spi_master/spi2/spi2.0/cros-ec-keyb.1/input/input0 [ 2.652124] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 2.656847] rtc (null): read_time: fail to read [ 2.661451] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc0 [ 2.667474] s3c-rtc 101e0000.rtc: warning: invalid RTC value so initializing it [ 2.675012] i2c /dev entries driver [ 2.683411] max77686 4-0009: Failed to find supply inb1 [ 2.687297] max77802-pmic max77802-pmic: regulator init failed for 0 [ 2.693539] platform max77802-pmic: Driver max77802-pmic requests probe deferral [ 2.703658] rtc (null): read_time: fail to read [ 2.706888] max77802-rtc max77802-rtc: rtc core: registered max77802-rtc as rtc1 [ 2.735598] atmel_mxt_ts 8-004b: Direct firmware load for maxtouch.cfg failed with error -2 [ 2.743869] input: Atmel maXTouch Touchpad as /devices/platform/12e00000.i2c/i2c-8/8-004b/input/input1 [ 2.752176] atmel_mxt_ts 8-004b: Family: 130 Variant: 35 Firmware V2.0.AA Objects: 23 [ 2.759662] tpm_i2c_infineon 9-0020: 1.2 TPM (device-id 0x1A) [ 2.850320] tps65090 20-0048: No cache defaults, reading back from HW [ 2.860084] of_get_named_gpiod_flags: can't parse 'dcdc-ext-control-gpios' property of node '/spi@12d40000/cros-ec@0/i2c-tunnel/power-regulator@48[0]' [ 2.872087] of_get_named_gpiod_flags: can't parse 'dcdc-ext-control-gpios' property of node '/spi@12d40000/cros-ec@0/i2c-tunnel/power-regulator@48[0]' [ 2.885548] of_get_named_gpiod_flags: can't parse 'dcdc-ext-control-gpios' property of node '/spi@12d40000/cros-ec@0/i2c-tunnel/power-regulator@48[0]' [ 2.899156] TPS65090_RAILSDCDC1: supplied by vbat-supply [ 2.905922] TPS65090_RAILSDCDC2: supplied by vbat-supply [ 2.911409] TPS65090_RAILSDCDC3: supplied by vbat-supply [ 2.916895] vcd_led: supplied by vbat-supply [ 2.925688] video_mid: supplied by TPS65090_RAILSDCDC1 [ 2.935378] wwan_r: supplied by TPS65090_RAILSDCDC2 [ 2.943517] sdcard: supplied by TPS65090_RAILSDCDC2 [ 2.948578] camout: supplied by TPS65090_RAILSDCDC2 [ 2.953627] lcd_vdd: supplied by TPS65090_RAILSDCDC2 [ 2.963097] video_mid_1a: supplied by TPS65090_RAILSDCDC1 [ 2.968693] TPS65090_RAILSLDO1: supplied by vbat-supply [ 2.972631] TPS65090_RAILSLDO2: supplied by vbat-supply [ 3.160792] sbs-battery 20-000b: sbs-battery: battery gas gauge device registered [ 3.181250] 10060000.tmu supply vtmu not found, using dummy regulator [ 3.186795] exynos-tmu 10060000.tmu: Exynos: Thermal zone(therm_zone0) registered [ 3.193925] 10064000.tmu supply vtmu not found, using dummy regulator [ 3.200838] exynos-tmu 10064000.tmu: Exynos: Thermal zone(therm_zone0) registered [ 3.207729] 10068000.tmu supply vtmu not found, using dummy regulator [ 3.214394] exynos-tmu 10068000.tmu: Exynos: Thermal zone(therm_zone0) registered [ 3.221517] 1006c000.tmu supply vtmu not found, using dummy regulator [ 3.228207] exynos-tmu 1006c000.tmu: Exynos: Thermal zone(therm_zone0) registered [ 3.235385] 100a0000.tmu supply vtmu not found, using dummy regulator [ 3.242243] exynos-tmu 100a0000.tmu: Exynos: Thermal zone(therm_zone0) registered [ 3.249910] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled [ 3.258347] device-mapper: ioctl: 4.29.0-ioctl (2014-10-28) initialised: dm-devel@redhat.com [ 3.265869] Driver 'mmcblk' needs updating - please use bus_type methods [ 3.272606] sdhci: Secure Digital Host Controller Interface driver [ 3.278737] sdhci: Copyright(c) Pierre Ossman [ 3.283255] Synopsys Designware Multimedia Card Interface Driver [ 3.289595] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 3.295918] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 3.302303] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 3.307735] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 107, 64 bit host data width, 64 deep fifo [ 3.317242] dwmmc_exynos 12200000.mmc: No vmmc regulator found [ 3.323029] dwmmc_exynos 12200000.mmc: No vqmmc regulator found [ 3.328938] dwmmc_exynos 12200000.mmc: GPIO lookup for consumer wp [ 3.335086] dwmmc_exynos 12200000.mmc: using device tree for GPIO lookup [ 3.341768] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/mmc@12200000[0]' [ 3.350530] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/mmc@12200000[0]' [ 3.359202] dwmmc_exynos 12200000.mmc: using lookup tables for GPIO lookup [ 3.366061] dwmmc_exynos 12200000.mmc: lookup for GPIO wp failed [ 3.398715] dwmmc_exynos 12200000.mmc: 1 slots initialized [ 3.403537] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 3.409627] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 3.416015] dwmmc_exynos 12220000.mmc: Version ID is 250a [ 3.421400] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 109, 64 bit host data width, 64 deep fifo [ 3.430943] dwmmc_exynos 12220000.mmc: No vmmc regulator found [ 3.436744] dwmmc_exynos 12220000.mmc: No vqmmc regulator found [ 3.441627] mmc0: BKOPS_EN bit is not set [ 3.445568] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0) [ 3.446428] mmc0: new HS200 MMC card at address 0001 [ 3.447543] mmcblk0: mmc0:0001 MAG2GC 14.5 GiB [ 3.447812] mmcblk0boot0: mmc0:0001 MAG2GC partition 1 4.00 MiB [ 3.448098] mmcblk0boot1: mmc0:0001 MAG2GC partition 2 4.00 MiB [ 3.448401] mmcblk0rpmb: mmc0:0001 MAG2GC partition 3 4.00 MiB [ 3.460925] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 [ 3.489326] dwmmc_exynos 12220000.mmc: GPIO lookup for consumer cd [ 3.495477] dwmmc_exynos 12220000.mmc: using device tree for GPIO lookup [ 3.502154] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/mmc@12220000[0]' [ 3.510937] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/mmc@12220000[0]' [ 3.519586] dwmmc_exynos 12220000.mmc: using lookup tables for GPIO lookup [ 3.526442] dwmmc_exynos 12220000.mmc: lookup for GPIO cd failed [ 3.532432] dwmmc_exynos 12220000.mmc: GPIO lookup for consumer wp [ 3.538598] dwmmc_exynos 12220000.mmc: using device tree for GPIO lookup [ 3.545267] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/mmc@12220000[0]' [ 3.554027] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/mmc@12220000[0]' [ 3.562701] dwmmc_exynos 12220000.mmc: using lookup tables for GPIO lookup [ 3.569560] dwmmc_exynos 12220000.mmc: lookup for GPIO wp failed [ 3.603642] dwmmc_exynos 12220000.mmc: 1 slots initialized [ 3.609436] usbcore: registered new interface driver usbhid [ 3.613526] usbhid: USB HID core driver [ 3.618167] exynos-adc 12d10000.adc: failed getting regulator, err = -517 [ 3.624142] platform 12d10000.adc: Driver exynos-adc requests probe deferral [ 24.188722] random: nonblocking pool is initialized