From: James Bottomley <James.Bottomley@SteelEye.com>
To: SCSI Mailing List <linux-scsi@vger.kernel.org>
Subject: [RFC] convert fusion to SPI transport class and use generic DV
Date: Thu, 09 Jun 2005 09:35:18 -0400 [thread overview]
Message-ID: <1118324118.5041.7.camel@mulgrave> (raw)
This code is more posted as an illustration of how to do things than an
actual patch for submission. However, I've tested this and it does
actually work:
ioc1: 53C1030: Capabilities={Initiator,Target}
scsi5 : ioc1: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=56
Vendor: HP 36.4G Model: ST336607LW Rev: HPC3
Type: Direct-Access ANSI SCSI revision: 03
target5:0:1: Beginning Domain Validation
target5:0:1: Ending Domain Validation
target5:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127)
jejb@titanic> ls /sys/class/spi_transport/target5\:0\:1/
device@ iu max_width offset period rd_strm rti wr_flow
dt max_offset min_period pcomp_en qas revalidate width
James
--- a/drivers/message/fusion/Kconfig
+++ b/drivers/message/fusion/Kconfig
@@ -9,6 +9,7 @@ config FUSION_SPI
tristate "Fusion MPT ScsiHost drivers for SPI"
depends on PCI && SCSI
select FUSION
+ select SCSI_SPI_ATTRS
---help---
SCSI HOST support for a parallel SCSI host adapters.
--- a/drivers/message/fusion/mptscsih.c
+++ b/drivers/message/fusion/mptscsih.c
@@ -2507,7 +2507,7 @@ mptscsih_ioc_reset(MPT_ADAPTER *ioc, int
/* 4. Renegotiate to all devices, if SCSI
*/
if (ioc->bus_type == SCSI) {
- dnegoprintk(("writeSDP1: ALL_IDS USE_NVRAM\n"));
+ printk("writeSDP1: ALL_IDS USE_NVRAM\n");
mptscsih_writeSDP1(hd, 0, 0, MPT_SCSICFG_ALL_IDS | MPT_SCSICFG_USE_NVRAM);
}
@@ -2766,7 +2766,7 @@ mptscsih_initTarget(MPT_SCSI_HOST *hd, i
vdev->tflags |= MPT_TARGET_FLAGS_VALID_56;
}
}
- mptscsih_setTargetNegoParms(hd, vdev, data_56);
+ //mptscsih_setTargetNegoParms(hd, vdev, data_56);
} else {
/* Initial Inquiry may not request enough data bytes to
* obtain byte 57. DV will; if target doesn't return
@@ -2777,7 +2777,7 @@ mptscsih_initTarget(MPT_SCSI_HOST *hd, i
*/
data_56 = data[56];
vdev->tflags |= MPT_TARGET_FLAGS_VALID_56;
- mptscsih_setTargetNegoParms(hd, vdev, data_56);
+ //mptscsih_setTargetNegoParms(hd, vdev, data_56);
}
}
}
@@ -2806,6 +2806,8 @@ mptscsih_setTargetNegoParms(MPT_SCSI_HOS
target->negoFlags = pspi_data->noQas;
+ printk("HERE\n");
+
/* noQas == 0 => device supports QAS. Need byte 56 of Inq to determine
* support. If available, default QAS to off and allow enabling.
* If not available, default QAS to on, turn off for non-disks.
@@ -3105,6 +3107,8 @@ mptscsih_writeSDP1(MPT_SCSI_HOST *hd, in
u8 negoFlags;
u8 maxwidth, maxoffset, maxfactor;
+ printk("HERE2\n");
+
if (ioc->spi_data.sdp1length == 0)
return 0;
@@ -3204,8 +3208,8 @@ mptscsih_writeSDP1(MPT_SCSI_HOST *hd, in
return -EAGAIN;
}
- ddvprintk((MYIOC_s_INFO_FMT "WriteSDP1 (mf=%p, id=%d, req=0x%x, cfg=0x%x)\n",
- hd->ioc->name, mf, id, requested, configuration));
+ printk(MYIOC_s_INFO_FMT "WriteSDP1 (mf=%p, id=%d, req=0x%x, cfg=0x%x)\n",
+ hd->ioc->name, mf, id, requested, configuration);
/* Set the request and the data pointers.
@@ -4228,12 +4232,12 @@ mptscsih_qas_check(MPT_SCSI_HOST *hd, in
if ((pTarget != NULL) && (!pTarget->raidVolume)) {
if ((pTarget->negoFlags & hd->ioc->spi_data.noQas) == 0) {
pTarget->negoFlags |= hd->ioc->spi_data.noQas;
- dnegoprintk(("writeSDP1: id=%d flags=0\n", id));
+ printk("writeSDP1: id=%d flags=0\n", id);
mptscsih_writeSDP1(hd, 0, ii, 0);
}
} else {
if (mptscsih_is_phys_disk(hd->ioc, ii) == 1) {
- dnegoprintk(("writeSDP1: id=%d SCSICFG_USE_NVRAM\n", id));
+ printk("writeSDP1: id=%d SCSICFG_USE_NVRAM\n", id);
mptscsih_writeSDP1(hd, 0, ii, MPT_SCSICFG_USE_NVRAM);
}
}
--- a/drivers/message/fusion/mptscsih.h
+++ b/drivers/message/fusion/mptscsih.h
@@ -67,7 +67,7 @@
* capabilities.
*/
-#define MPTSCSIH_ENABLE_DOMAIN_VALIDATION
+#undef MPTSCSIH_ENABLE_DOMAIN_VALIDATION
/* SCSI driver setup structure. Settings can be overridden
--- a/drivers/message/fusion/mptspi.c
+++ b/drivers/message/fusion/mptspi.c
@@ -62,6 +62,8 @@
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_tcq.h>
+#include <scsi/scsi_transport.h>
+#include <scsi/scsi_transport_spi.h>
#include "mptbase.h"
#include "mptscsih.h"
@@ -98,6 +100,8 @@ static int mpt_pq_filter = 0;
module_param(mpt_pq_filter, int, 0);
MODULE_PARM_DESC(mpt_pq_filter, " Enable peripheral qualifier filter: enable=1 (default=0)");
+static struct scsi_transport_template *mptspi_transport_template = NULL;
+
static int mptspiDoneCtx = -1;
static int mptspiTaskCtx = -1;
static int mptspiInternalCtx = -1; /* Used only for internal commands */
@@ -115,6 +119,48 @@ static struct device_attribute *mptspi_d
NULL,
};
+static int mptspi_target_alloc(struct scsi_target *starget)
+{
+ struct Scsi_Host *shost = dev_to_shost(&starget->dev);
+ struct _MPT_SCSI_HOST *hd = (struct _MPT_SCSI_HOST *)shost->hostdata;
+ static void mptspi_write_offset(struct scsi_target *, int);
+ static void mptspi_write_width(struct scsi_target *, int);
+
+ if (hd == NULL)
+ return -ENODEV;
+
+ if (hd->ioc->spi_data.nvram &&
+ hd->ioc->spi_data.nvram[starget->id] != MPT_HOST_NVRAM_INVALID) {
+ u32 nvram = hd->ioc->spi_data.nvram[starget->id];
+ spi_min_period(starget) = (nvram & MPT_NVRAM_SYNC_MASK) >> MPT_NVRAM_SYNC_SHIFT;
+ spi_max_width(starget) = nvram & MPT_NVRAM_WIDE_DISABLE ? 0 : 1;
+ } else {
+ spi_min_period(starget) = hd->ioc->spi_data.minSyncFactor;
+ spi_max_width(starget) = hd->ioc->spi_data.maxBusWidth;
+ }
+ spi_max_offset(starget) = hd->ioc->spi_data.maxSyncOffset;
+
+ spi_offset(starget) = 0;
+ mptspi_write_width(starget, 0);
+
+ return 0;
+}
+
+static int mptspi_slave_configure(struct scsi_device *sdev)
+{
+ int ret = mptscsih_slave_configure(sdev);
+
+ if (ret)
+ return ret;
+
+ if (!spi_initial_dv(sdev->sdev_target)) {
+ spi_dv_device(sdev);
+ spi_display_xfer_agreement(sdev->sdev_target);
+ }
+
+ return 0;
+}
+
static struct scsi_host_template mptspi_driver_template = {
.proc_name = "mptspi",
.proc_info = mptscsih_proc_info,
@@ -122,8 +168,9 @@ static struct scsi_host_template mptspi_
.info = mptscsih_info,
.queuecommand = mptscsih_qcmd,
.slave_alloc = mptscsih_slave_alloc,
- .slave_configure = mptscsih_slave_configure,
+ .slave_configure = mptspi_slave_configure,
.slave_destroy = mptscsih_slave_destroy,
+ .target_alloc = mptspi_target_alloc,
.eh_abort_handler = mptscsih_abort,
.eh_device_reset_handler = mptscsih_dev_reset,
.eh_bus_reset_handler = mptscsih_bus_reset,
@@ -138,6 +185,325 @@ static struct scsi_host_template mptspi_
.sdev_attrs = mptspi_dev_attrs,
};
+static int mptspi_read_page0(struct scsi_target *starget,
+ struct _CONFIG_PAGE_SCSI_DEVICE_0 *pass_pg0)
+{
+ struct Scsi_Host *shost = dev_to_shost(&starget->dev);
+ struct _MPT_SCSI_HOST *hd = (struct _MPT_SCSI_HOST *)shost->hostdata;
+ struct _MPT_ADAPTER *ioc = hd->ioc;
+ struct _CONFIG_PAGE_SCSI_DEVICE_0 *pg0;
+ dma_addr_t pg0_dma;
+ int size;
+ struct _x_config_parms cfg;
+ struct _CONFIG_PAGE_HEADER hdr;
+ int err = -EBUSY;
+
+ size = ioc->spi_data.sdp0length * 4;
+ /*
+ if (ioc->spi_data.sdp0length & 1)
+ size += size + 4;
+ size += 2048;
+ */
+
+ pg0 = dma_alloc_coherent(&ioc->pcidev->dev, size, &pg0_dma, GFP_KERNEL);
+ if (pg0 == NULL) {
+ dev_printk(KERN_ERR, &starget->dev, "dma_alloc_coherent for parameters failed\n");
+ return -EINVAL;
+ }
+
+ memset(&hdr, 0, sizeof(hdr));
+
+ hdr.PageVersion = ioc->spi_data.sdp0version;
+ hdr.PageLength = ioc->spi_data.sdp0length;
+ hdr.PageNumber = 0;
+ hdr.PageType = MPI_CONFIG_PAGETYPE_SCSI_DEVICE;
+
+ memset(&cfg, 0, sizeof(cfg));
+
+ cfg.hdr = &hdr;
+ cfg.physAddr = pg0_dma;
+ cfg.action = MPI_CONFIG_ACTION_PAGE_READ_CURRENT;
+ cfg.dir = 0;
+ cfg.pageAddr = (starget->channel << 8) | starget->id;
+
+ if (mpt_config(ioc, &cfg)) {
+ dev_printk(KERN_ERR, &starget->dev, "mpt_config failed\n");
+ goto out_free;
+ }
+ err = 0;
+ memcpy(pass_pg0, pg0, size);
+
+ out_free:
+ dma_free_coherent(&ioc->pcidev->dev, size, pg0, pg0_dma);
+ return err;
+}
+
+static void mptspi_read_parameters(struct scsi_target *starget)
+{
+ int nego;
+ struct _CONFIG_PAGE_SCSI_DEVICE_0 pg0;
+
+ mptspi_read_page0(starget, &pg0);
+
+ nego = le32_to_cpu(pg0.NegotiatedParameters);
+
+ spi_iu(starget) = (nego & MPI_SCSIDEVPAGE0_NP_IU) ? 1 : 0;
+ spi_dt(starget) = (nego & MPI_SCSIDEVPAGE0_NP_DT) ? 1 : 0;
+ spi_qas(starget) = (nego & MPI_SCSIDEVPAGE0_NP_QAS) ? 1 : 0;
+ //spi_hold_mcs(starget) = (nego & MPI_SCSIDEVPAGE0_NP_HOLD_MCS) ? 1 : 0;
+ spi_wr_flow(starget) = (nego & MPI_SCSIDEVPAGE0_NP_WR_FLOW) ? 1 : 0;
+ spi_rd_strm(starget) = (nego & MPI_SCSIDEVPAGE0_NP_RD_STRM) ? 1 : 0;
+ spi_rti(starget) = (nego & MPI_SCSIDEVPAGE0_NP_RTI) ? 1 : 0;
+ spi_pcomp_en(starget) = (nego & MPI_SCSIDEVPAGE0_NP_PCOMP_EN) ? 1 : 0;
+ spi_period(starget) = (nego & MPI_SCSIDEVPAGE0_NP_NEG_SYNC_PERIOD_MASK) >> MPI_SCSIDEVPAGE0_NP_SHIFT_SYNC_PERIOD;
+ spi_offset(starget) = (nego & MPI_SCSIDEVPAGE0_NP_NEG_SYNC_OFFSET_MASK) >> MPI_SCSIDEVPAGE0_NP_SHIFT_SYNC_OFFSET;
+ spi_width(starget) = (nego & MPI_SCSIDEVPAGE0_NP_WIDE) ? 1 : 0;
+}
+
+static int mptspi_write_page1(struct scsi_target *starget,
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 *pass_pg1)
+{
+ struct Scsi_Host *shost = dev_to_shost(&starget->dev);
+ struct _MPT_SCSI_HOST *hd = (struct _MPT_SCSI_HOST *)shost->hostdata;
+ struct _MPT_ADAPTER *ioc = hd->ioc;
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 *pg1;
+ dma_addr_t pg1_dma;
+ int size;
+ struct _x_config_parms cfg;
+ struct _CONFIG_PAGE_HEADER hdr;
+ int err = -EBUSY;
+
+ size = ioc->spi_data.sdp1length * 4;
+
+ pg1 = dma_alloc_coherent(&ioc->pcidev->dev, size, &pg1_dma, GFP_KERNEL);
+ if (pg1 == NULL) {
+ dev_printk(KERN_ERR, &starget->dev, "dma_alloc_coherent for parameters failed\n");
+ return -EINVAL;
+ }
+
+ memset(&hdr, 0, sizeof(hdr));
+
+ hdr.PageVersion = ioc->spi_data.sdp1version;
+ hdr.PageLength = ioc->spi_data.sdp1length;
+ hdr.PageNumber = 1;
+ hdr.PageType = MPI_CONFIG_PAGETYPE_SCSI_DEVICE;
+
+ memset(&cfg, 0, sizeof(cfg));
+
+ cfg.hdr = &hdr;
+ cfg.physAddr = pg1_dma;
+ cfg.action = MPI_CONFIG_ACTION_PAGE_WRITE_CURRENT;
+ cfg.dir = 1;
+ cfg.pageAddr = (starget->channel << 8) | starget->id;
+
+ memcpy(pg1, pass_pg1, size);
+
+ pg1->Header.PageVersion = hdr.PageVersion;
+ pg1->Header.PageLength = hdr.PageLength;
+ pg1->Header.PageNumber = hdr.PageNumber;
+ pg1->Header.PageType = hdr.PageType;
+
+ if (mpt_config(ioc, &cfg)) {
+ dev_printk(KERN_ERR, &starget->dev, "mpt_config failed\n");
+ goto out_free;
+ }
+ err = 0;
+
+ out_free:
+ dma_free_coherent(&ioc->pcidev->dev, size, pg1, pg1_dma);
+ return err;
+}
+
+static u32 mptspi_getRP(struct scsi_target *starget)
+{
+ u32 nego = 0;
+
+ nego |= spi_iu(starget) ? MPI_SCSIDEVPAGE1_RP_IU : 0;
+ nego |= spi_dt(starget) ? MPI_SCSIDEVPAGE1_RP_DT : 0;
+ nego |= spi_qas(starget) ? MPI_SCSIDEVPAGE1_RP_QAS : 0;
+ //nego |= spi_hold_mcs(starget) ? MPI_SCSIDEVPAGE1_RP_HOLD_MCS : 0;
+ nego |= spi_wr_flow(starget) ? MPI_SCSIDEVPAGE1_RP_WR_FLOW : 0;
+ nego |= spi_rd_strm(starget) ? MPI_SCSIDEVPAGE1_RP_RD_STRM : 0;
+ nego |= spi_rti(starget) ? MPI_SCSIDEVPAGE1_RP_RTI : 0;
+ nego |= spi_pcomp_en(starget) ? MPI_SCSIDEVPAGE1_RP_PCOMP_EN : 0;
+
+ nego |= (spi_period(starget) << MPI_SCSIDEVPAGE1_RP_SHIFT_MIN_SYNC_PERIOD) & MPI_SCSIDEVPAGE1_RP_MIN_SYNC_PERIOD_MASK;
+ nego |= (spi_offset(starget) << MPI_SCSIDEVPAGE1_RP_SHIFT_MAX_SYNC_OFFSET) & MPI_SCSIDEVPAGE1_RP_MAX_SYNC_OFFSET_MASK;
+ nego |= spi_width(starget) ? MPI_SCSIDEVPAGE1_RP_WIDE : 0;
+
+ return nego;
+}
+
+static void mptspi_write_offset(struct scsi_target *starget, int offset)
+{
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1;
+ u32 nego;
+
+ if (offset < 0)
+ offset = 0;
+
+ if (offset > 255)
+ offset = 255;
+
+ if (spi_offset(starget) == -1)
+ mptspi_read_parameters(starget);
+
+ spi_offset(starget) = offset;
+
+ nego = mptspi_getRP(starget);
+
+ pg1.RequestedParameters = cpu_to_le32(nego);
+ pg1.Reserved = 0;
+ pg1.Configuration = 0;
+
+ mptspi_write_page1(starget, &pg1);
+}
+
+static void mptspi_write_period(struct scsi_target *starget, int period)
+{
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1;
+ u32 nego;
+
+ if (period < 8)
+ period = 8;
+
+ if (period > 255)
+ period = 255;
+
+ if (spi_period(starget) == -1)
+ mptspi_read_parameters(starget);
+
+ if (period == 8) {
+ spi_iu(starget) = 1;
+ spi_dt(starget) = 1;
+ } else if (period == 9) {
+ spi_dt(starget) = 1;
+ }
+
+ spi_period(starget) = period;
+
+ nego = mptspi_getRP(starget);
+
+ pg1.RequestedParameters = cpu_to_le32(nego);
+ pg1.Reserved = 0;
+ pg1.Configuration = 0;
+
+ mptspi_write_page1(starget, &pg1);
+}
+
+static void mptspi_write_dt(struct scsi_target *starget, int dt)
+{
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1;
+ u32 nego;
+
+ if (spi_period(starget) == -1)
+ mptspi_read_parameters(starget);
+
+ if (!dt && spi_period(starget) < 10)
+ spi_period(starget) = 10;
+
+ spi_dt(starget) = dt;
+
+ nego = mptspi_getRP(starget);
+
+
+ pg1.RequestedParameters = cpu_to_le32(nego);
+ pg1.Reserved = 0;
+ pg1.Configuration = 0;
+
+ mptspi_write_page1(starget, &pg1);
+}
+
+static void mptspi_write_iu(struct scsi_target *starget, int iu)
+{
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1;
+ u32 nego;
+
+ if (spi_period(starget) == -1)
+ mptspi_read_parameters(starget);
+
+ if (!iu && spi_period(starget) < 9)
+ spi_period(starget) = 9;
+
+ spi_iu(starget) = iu;
+
+ nego = mptspi_getRP(starget);
+
+
+ pg1.RequestedParameters = cpu_to_le32(nego);
+ pg1.Reserved = 0;
+ pg1.Configuration = 0;
+
+ mptspi_write_page1(starget, &pg1);
+}
+
+static void mptspi_write_qas(struct scsi_target *starget, int qas)
+{
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1;
+ u32 nego;
+
+ spi_qas(starget) = qas;
+
+ nego = mptspi_getRP(starget);
+
+ pg1.RequestedParameters = cpu_to_le32(nego);
+ pg1.Reserved = 0;
+ pg1.Configuration = 0;
+
+ mptspi_write_page1(starget, &pg1);
+}
+
+static void mptspi_write_width(struct scsi_target *starget, int width)
+{
+ struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1;
+ u32 nego;
+
+ if (!width) {
+ spi_dt(starget) = 0;
+ if (spi_period(starget) < 10)
+ spi_period(starget) = 10;
+ }
+
+ spi_width(starget) = width;
+
+ nego = mptspi_getRP(starget);
+
+ pg1.RequestedParameters = cpu_to_le32(nego);
+ pg1.Reserved = 0;
+ pg1.Configuration = 0;
+
+ mptspi_write_page1(starget, &pg1);
+}
+
+static struct spi_function_template mptspi_transport_functions = {
+ .get_offset = mptspi_read_parameters,
+ .set_offset = mptspi_write_offset,
+ .show_offset = 1,
+ .get_period = mptspi_read_parameters,
+ .set_period = mptspi_write_period,
+ .show_period = 1,
+ .get_width = mptspi_read_parameters,
+ .set_width = mptspi_write_width,
+ .show_width = 1,
+ .get_iu = mptspi_read_parameters,
+ .set_iu = mptspi_write_iu,
+ .show_iu = 1,
+ .get_dt = mptspi_read_parameters,
+ .set_dt = mptspi_write_dt,
+ .show_dt = 1,
+ .get_qas = mptspi_read_parameters,
+ .set_qas = mptspi_write_qas,
+ .show_qas = 1,
+ .get_wr_flow = mptspi_read_parameters,
+ .show_wr_flow = 1,
+ .get_rd_strm = mptspi_read_parameters,
+ .show_rd_strm = 1,
+ .get_rti = mptspi_read_parameters,
+ .show_rti = 1,
+ .get_pcomp_en = mptspi_read_parameters,
+ .show_pcomp_en = 1,
+};
+
/****************************************************************************
* Supported hardware
@@ -382,7 +748,6 @@ mptspi_probe(struct pci_dev *pdev, const
mpt_saf_te,
mpt_pq_filter));
#endif
-
ioc->spi_data.forceDv = 0;
ioc->spi_data.noQas = 0;
@@ -398,6 +763,11 @@ mptspi_probe(struct pci_dev *pdev, const
hd->scandv_wait_done = 0;
hd->last_queue_full = 0;
+ /* Some versions of the firmware don't support page 0; without
+ * that we can't get the parameters */
+ if (hd->ioc->spi_data.sdp0length != 0)
+ sh->transportt = mptspi_transport_template;
+
error = scsi_add_host (sh, &ioc->pcidev->dev);
if(error) {
dprintk((KERN_ERR MYNAM
@@ -441,6 +811,10 @@ mptspi_init(void)
show_mptmod_ver(my_NAME, my_VERSION);
+ mptspi_transport_template = spi_attach_transport(&mptspi_transport_functions);
+ if (!mptspi_transport_template)
+ return -ENODEV;
+
mptspiDoneCtx = mpt_register(mptscsih_io_done, MPTSPI_DRIVER);
mptspiTaskCtx = mpt_register(mptscsih_taskmgmt_complete, MPTSPI_DRIVER);
mptspiInternalCtx = mpt_register(mptscsih_scandv_complete, MPTSPI_DRIVER);
reply other threads:[~2005-06-09 13:35 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1118324118.5041.7.camel@mulgrave \
--to=james.bottomley@steeleye.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox