From: Giuseppe Sacco <giuseppe@eppesuigoccas.homedns.org>
To: linux-scsi@vger.kernel.org
Subject: Re: question about qlogic QLA2312
Date: Fri, 15 Sep 2006 17:54:02 +0200 [thread overview]
Message-ID: <1158335642.8103.70.camel@scarafaggio> (raw)
In-Reply-To: <19dce7c30609150656s4397bbfeyba53586cb2105ab7@mail.gmail.com>
[-- Attachment #1: Type: text/plain, Size: 439 bytes --]
Il giorno ven, 15/09/2006 alle 19.26 +0530, G Shyam Sundar ha scritto:
> Which version of the driver are you using ?
> Also, what is the version of the firmware ? You can get the version of
> fimware by
> # grep FW_VERSION_STRING in the source directory.
>
> It will be helpful if you could recompile the driver with
> QL_DEBUG_LEVEL_2 enabled (qla_dbg.h) and recreate the issue.
Here it is, with some more debug levels (1,2,3, and 7)
[-- Attachment #2: qla2xxx-8.01.06b2-debug.log --]
[-- Type: text/x-log, Size: 5940 bytes --]
Sep 15 17:49:01 lnx01 kernel: qla2xxx_conf: module not supported by Novell, setting U taint flag.
Sep 15 17:49:01 lnx01 kernel: qla2xxx: module not supported by Novell, setting U taint flag.
Sep 15 17:49:01 lnx01 kernel: QLogic Fibre Channel HBA Driver
Sep 15 17:49:01 lnx01 kernel: qla2300: module not supported by Novell, setting U taint flag.
Sep 15 17:49:01 lnx01 kernel: ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 177
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Found an ISP2312, irq 177, iobase 0xffffc20000f72000
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Configuring PCI space...
Sep 15 17:49:01 lnx01 kernel: qla2x00_get_flash_version(): read BIOS 1.47.
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Configure NVRAM parameters...
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Verifying loaded RISC code...
Sep 15 17:49:01 lnx01 kernel: scsi(11): Testing device at ffffc20000f72000.
Sep 15 17:49:01 lnx01 kernel: scsi(11): Reset register cleared by chip reset
Sep 15 17:49:01 lnx01 kernel: scsi(11): Checking product ID of chip
Sep 15 17:49:01 lnx01 kernel: scsi(11): Checking mailboxes.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): Loaded MBX registers (displayed in bytes) =
Sep 15 17:49:01 lnx01 kernel: 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 06 00 aa aa 55 55 55 aa aa 55 a5 a5 5a 5a 25 25
Sep 15 17:49:01 lnx01 kernel:
Sep 15 17:49:01 lnx01 kernel: 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 20 50 f7 00 00 00 00 00 08 00 00 80 00 00 00 00
Sep 15 17:49:01 lnx01 kernel:
Sep 15 17:49:01 lnx01 kernel: 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 53 49 f7 00 00 00 00 00
Sep 15 17:49:01 lnx01 kernel:
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): I/O address = ffffc20000f72080.
Sep 15 17:49:01 lnx01 kernel: Mailbox registers:
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 0 0x0000
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 1 0x4953
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 2 0x5020
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 3 0x2020
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 4 0x0002
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 5 0x0004
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): cmd=6 POLLING MODE.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mbx_completion(11): Got mailbox completion. cmd=6.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): cmd 6 completed.
Sep 15 17:49:01 lnx01 kernel: scsi(11): Loading risc segment@ addr ffffffff8836fc40, number of bytes 0x8000, offset 0x800.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): Loaded MBX registers (displayed in bytes) =
Sep 15 17:49:01 lnx01 kernel: 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 09 00 00 08 78 fc 00 00 00 80 00 00 00 00 01 00
Sep 15 17:49:01 lnx01 kernel:
Sep 15 17:49:01 lnx01 kernel: 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: b8 3a da f3 01 81 ff ff f8 39 da f3 01 81 ff ff
Sep 15 17:49:01 lnx01 kernel:
Sep 15 17:49:01 lnx01 kernel: 0 1 2 3 4 5 6 7 8 9 Ah Bh Ch Dh Eh Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 80 84 03 05 02 81 ff ff
Sep 15 17:49:01 lnx01 kernel:
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): I/O address = ffffc20000f72080.
Sep 15 17:49:01 lnx01 kernel: Mailbox registers:
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 0 0x4000
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 1 0xaaaa
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 2 0x5555
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 3 0xaa55
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 4 0x55aa
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 5 0xa5a5
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): cmd=9 POLLING MODE.
Sep 15 17:49:31 lnx01 kernel: qla2x00_mailbox_command(11): **** MB Command Timeout for cmd 9 ****
Sep 15 17:49:31 lnx01 kernel: qla2x00_mailbox_command(11): icontrol=0 jiffies=100055e49
Sep 15 17:49:31 lnx01 kernel: qla2x00_mailbox_command(11): *** mailbox[0] = 0x4000 ***
Sep 15 17:49:31 lnx01 kernel: Mailbox registers:
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 0 0x4000
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 1 0xaaaa
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 2 0x5555
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 3 0xaa55
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 4 0x55aa
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 5 0xa5a5
Sep 15 17:49:31 lnx01 kernel: qla2300 0000:03:02.0: Mailbox command timeout occured. Scheduling ISP abort.
Sep 15 17:49:31 lnx01 kernel: qla2300 0000:03:02.0: [ERROR] Failed to load segment 0 of firmware
Sep 15 17:49:31 lnx01 kernel: Mailbox registers:
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 0 0x4000
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 1 0xaaaa
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 2 0x5555
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 3 0xaa55
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 4 0x55aa
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 5 0xa5a5
Sep 15 17:49:31 lnx01 kernel: qla2300 0000:03:02.0: Failed to initialize adapter
Sep 15 17:49:31 lnx01 kernel: qla2300: probe of 0000:03:02.0 failed with error -1
prev parent reply other threads:[~2006-09-15 15:53 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-09-15 8:00 question about qlogic QLA2312 Giuseppe Sacco
2006-09-15 13:56 ` G Shyam Sundar
2006-09-15 14:12 ` Giuseppe Sacco
2006-09-15 15:54 ` Giuseppe Sacco [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1158335642.8103.70.camel@scarafaggio \
--to=giuseppe@eppesuigoccas.homedns.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox