* BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
@ 2007-12-05 16:36 Lee Schermerhorn
2007-12-05 21:20 ` Andrew Morton
0 siblings, 1 reply; 8+ messages in thread
From: Lee Schermerhorn @ 2007-12-05 16:36 UTC (permalink / raw)
To: linux-scsi; +Cc: Andrew Morton, James.Bottomley, Eric.Moore
As reported here:
http://marc.info/?l=linux-scsi&m=119645761124683&w=4
against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
I can boot by disabling async scan. However, I've also noticed some
disks attached via one of the "mpt" adapters ["scsi8" in console long in
message linked above] going "off-line" during stress tests. This was
under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
Regards,
Lee
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-05 16:36 BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan Lee Schermerhorn
@ 2007-12-05 21:20 ` Andrew Morton
2007-12-05 21:44 ` Lee Schermerhorn
2007-12-06 18:14 ` Lee Schermerhorn
0 siblings, 2 replies; 8+ messages in thread
From: Andrew Morton @ 2007-12-05 21:20 UTC (permalink / raw)
To: Lee Schermerhorn; +Cc: linux-scsi, James.Bottomley, Eric.Moore
On Wed, 05 Dec 2007 11:36:39 -0500
Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> As reported here:
>
> http://marc.info/?l=linux-scsi&m=119645761124683&w=4
>
> against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
>
> I can boot by disabling async scan. However, I've also noticed some
> disks attached via one of the "mpt" adapters ["scsi8" in console long in
> message linked above] going "off-line" during stress tests. This was
> under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
>
Is ther any way of tricking you into
http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
Obvious culprits to start with would be git-scsi-misc and maybe
scsi-early-detection-of-medium-not-present-updated.patch. But there are
only 20-odd scsi patches in there.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-05 21:20 ` Andrew Morton
@ 2007-12-05 21:44 ` Lee Schermerhorn
2007-12-06 18:14 ` Lee Schermerhorn
1 sibling, 0 replies; 8+ messages in thread
From: Lee Schermerhorn @ 2007-12-05 21:44 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-scsi, James.Bottomley, Eric.Moore, Eric Whitney
On Wed, 2007-12-05 at 13:20 -0800, Andrew Morton wrote:
> On Wed, 05 Dec 2007 11:36:39 -0500
> Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
>
> > As reported here:
> >
> > http://marc.info/?l=linux-scsi&m=119645761124683&w=4
> >
> > against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> > platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> > seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
> >
> > I can boot by disabling async scan. However, I've also noticed some
> > disks attached via one of the "mpt" adapters ["scsi8" in console long in
> > message linked above] going "off-line" during stress tests. This was
> > under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
> >
>
> Is ther any way of tricking you into
> http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
>
> Obvious culprits to start with would be git-scsi-misc and maybe
> scsi-early-detection-of-medium-not-present-updated.patch. But there are
> only 20-odd scsi patches in there.
I'll try to get to it tomorrow am.
Lee
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-05 21:20 ` Andrew Morton
2007-12-05 21:44 ` Lee Schermerhorn
@ 2007-12-06 18:14 ` Lee Schermerhorn
2007-12-06 18:35 ` Andrew Morton
1 sibling, 1 reply; 8+ messages in thread
From: Lee Schermerhorn @ 2007-12-06 18:14 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-scsi, James.Bottomley, Eric.Moore, Eric Whitney
On Wed, 2007-12-05 at 13:20 -0800, Andrew Morton wrote:
> On Wed, 05 Dec 2007 11:36:39 -0500
> Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
>
> > As reported here:
> >
> > http://marc.info/?l=linux-scsi&m=119645761124683&w=4
> >
> > against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> > platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> > seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
> >
> > I can boot by disabling async scan. However, I've also noticed some
> > disks attached via one of the "mpt" adapters ["scsi8" in console long in
> > message linked above] going "off-line" during stress tests. This was
> > under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
> >
>
> Is ther any way of tricking you into
> http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
>
> Obvious culprits to start with would be git-scsi-misc and maybe
> scsi-early-detection-of-medium-not-present-updated.patch. But there are
> only 20-odd scsi patches in there.
The reported hang occurs after pushing the git-scsi-misc patch. I'm
looking into it now, but it's rather large and I'm a neophyte in this
area. If James can point me at a broken-out quilt series for this
patch, I'd be willing to try to bisect that--assuming that it IS
bisectable.
Lee
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-06 18:14 ` Lee Schermerhorn
@ 2007-12-06 18:35 ` Andrew Morton
2007-12-06 19:01 ` Lee Schermerhorn
2007-12-07 19:38 ` Lee Schermerhorn
0 siblings, 2 replies; 8+ messages in thread
From: Andrew Morton @ 2007-12-06 18:35 UTC (permalink / raw)
To: Lee Schermerhorn; +Cc: linux-scsi, James.Bottomley, Eric.Moore, Eric Whitney
On Thu, 06 Dec 2007 13:14:22 -0500 Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> On Wed, 2007-12-05 at 13:20 -0800, Andrew Morton wrote:
> > On Wed, 05 Dec 2007 11:36:39 -0500
> > Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> >
> > > As reported here:
> > >
> > > http://marc.info/?l=linux-scsi&m=119645761124683&w=4
> > >
> > > against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> > > platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> > > seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
> > >
> > > I can boot by disabling async scan. However, I've also noticed some
> > > disks attached via one of the "mpt" adapters ["scsi8" in console long in
> > > message linked above] going "off-line" during stress tests. This was
> > > under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
> > >
> >
> > Is ther any way of tricking you into
> > http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
> >
> > Obvious culprits to start with would be git-scsi-misc and maybe
> > scsi-early-detection-of-medium-not-present-updated.patch. But there are
> > only 20-odd scsi patches in there.
>
> The reported hang occurs after pushing the git-scsi-misc patch.
OK, thanks.
> I'm
> looking into it now, but it's rather large and I'm a neophyte in this
> area. If James can point me at a broken-out quilt series for this
> patch, I'd be willing to try to bisect that--
I doubt if such a thing exists.
> assuming that it IS
> bisectable.
Often git trees are not bisectable. But they should be.
Your best bet is to do a git-bisect on
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git
http://www.kernel.org/doc/local/git-quick.html
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-06 18:35 ` Andrew Morton
@ 2007-12-06 19:01 ` Lee Schermerhorn
2007-12-11 18:23 ` Lee Schermerhorn
2007-12-07 19:38 ` Lee Schermerhorn
1 sibling, 1 reply; 8+ messages in thread
From: Lee Schermerhorn @ 2007-12-06 19:01 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-scsi, James.Bottomley, Eric.Moore, Eric Whitney
On Thu, 2007-12-06 at 10:35 -0800, Andrew Morton wrote:
> On Thu, 06 Dec 2007 13:14:22 -0500 Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
>
> > On Wed, 2007-12-05 at 13:20 -0800, Andrew Morton wrote:
> > > On Wed, 05 Dec 2007 11:36:39 -0500
> > > Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> > >
> > > > As reported here:
> > > >
> > > > http://marc.info/?l=linux-scsi&m=119645761124683&w=4
> > > >
> > > > against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> > > > platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> > > > seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
> > > >
> > > > I can boot by disabling async scan. However, I've also noticed some
> > > > disks attached via one of the "mpt" adapters ["scsi8" in console long in
> > > > message linked above] going "off-line" during stress tests. This was
> > > > under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
> > > >
> > >
> > > Is ther any way of tricking you into
> > > http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
> > >
> > > Obvious culprits to start with would be git-scsi-misc and maybe
> > > scsi-early-detection-of-medium-not-present-updated.patch. But there are
> > > only 20-odd scsi patches in there.
> >
> > The reported hang occurs after pushing the git-scsi-misc patch.
>
> OK, thanks.
>
> > I'm
> > looking into it now, but it's rather large and I'm a neophyte in this
> > area. If James can point me at a broken-out quilt series for this
> > patch, I'd be willing to try to bisect that--
>
> I doubt if such a thing exists.
>
> > assuming that it IS
> > bisectable.
>
> Often git trees are not bisectable. But they should be.
>
> Your best bet is to do a git-bisect on
> git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git
>
> http://www.kernel.org/doc/local/git-quick.html
>
Ah, well... Can't promise that will happen any time soon...
Lee
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-06 18:35 ` Andrew Morton
2007-12-06 19:01 ` Lee Schermerhorn
@ 2007-12-07 19:38 ` Lee Schermerhorn
1 sibling, 0 replies; 8+ messages in thread
From: Lee Schermerhorn @ 2007-12-07 19:38 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-scsi, James.Bottomley, Eric.Moore, Eric Whitney
On Thu, 2007-12-06 at 10:35 -0800, Andrew Morton wrote:
> On Thu, 06 Dec 2007 13:14:22 -0500 Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
>
> > On Wed, 2007-12-05 at 13:20 -0800, Andrew Morton wrote:
> > > On Wed, 05 Dec 2007 11:36:39 -0500
> > > Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> > >
> > > > As reported here:
> > > >
> > > > http://marc.info/?l=linux-scsi&m=119645761124683&w=4
> > > >
> > > > against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> > > > platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> > > > seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
> > > >
> > > > I can boot by disabling async scan. However, I've also noticed some
> > > > disks attached via one of the "mpt" adapters ["scsi8" in console long in
> > > > message linked above] going "off-line" during stress tests. This was
> > > > under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
> > > >
> > >
> > > Is ther any way of tricking you into
> > > http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
> > >
> > > Obvious culprits to start with would be git-scsi-misc and maybe
> > > scsi-early-detection-of-medium-not-present-updated.patch. But there are
> > > only 20-odd scsi patches in there.
> >
> > The reported hang occurs after pushing the git-scsi-misc patch.
>
> OK, thanks.
More info on the hang.
I thought I'd enable the debug prints in just mpt_config() to see if I
could see why it "failed" when the hang occurs. [Hacky patch below.].
However, when I enable the printk's the system boots fine with
git-scsi-misc applied, even with async scan enabled. An extract of the
console log of the messages is included below, in case that provides a
clue to anyone who might care.
One other thing: If I leave the system in the hung state long enough, I
start seeing stack dumps and messages about tasks blocked for more than
120 seconds [swapper and scsi_scan_[89]]. Section of the log included
below.
I'll keep investigating in the background...
Lee
-------------------------------
temp mpt debug patch
drivers/message/fusion/mptbase.c | 5 +++++
1 file changed, 5 insertions(+)
Index: Linux/drivers/message/fusion/mptbase.c
===================================================================
--- Linux.orig/drivers/message/fusion/mptbase.c 2007-12-07 12:12:00.000000000 -0500
+++ Linux/drivers/message/fusion/mptbase.c 2007-12-07 12:16:29.000000000 -0500
@@ -5633,6 +5633,9 @@ SendEventAck(MPT_ADAPTER *ioc, EventNoti
* -EAGAIN if no msg frames currently available
* -EFAULT for non-successful reply or no reply (timeout)
*/
+// brute force enable dcprintk for just this function
+#undef dcprintk
+#define dcprintk(IOC, CMD) CMD
int
mpt_config(MPT_ADAPTER *ioc, CONFIGPARMS *pCfg)
{
@@ -5746,6 +5749,8 @@ mpt_config(MPT_ADAPTER *ioc, CONFIGPARMS
return rc;
}
+#undef dcprintk
+#define dcprintk(IOC, CMD)
/*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
/**
-----------------------------------------------
console log extract of messages from patch above:
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
GSI 43 (level, low) -> CPU 2 (0x0800) vector 74
ACPI: PCI Interrupt 0000:38:01.0[A] -> GSI 43 (level, low) -> IRQ 74
mptbase: ioc0: Initiating bringup
ioc0: LSI53C1030 C0: Capabilities={Initiator,Target}
mptbase: ioc0: Sending Config request type 3, page 0 and action 0
mptbase: ioc0: Sending Config request type 3, page 0 and action 1
mptbase: ioc0: Sending Config request type 3, page 2 and action 0
mptbase: ioc0: Sending Config request type 3, page 2 and action 6
mptbase: ioc0: Sending Config request type 4, page 1 and action 0
mptbase: ioc0: Sending Config request type 4, page 0 and action 0
mptbase: ioc0: Sending Config request type 1, page 1 and action 0
mptbase: ioc0: Sending Config request type 1, page 1 and action 1
mptbase: ioc0: Sending Config request type 1, page 4 and action 0
mptbase: ioc0: Sending Config request type 1, page 4 and action 1
mptbase: ioc0: Sending Config request type 0, page 2 and action 0
mptbase: ioc0: Sending Config request type 0, page 2 and action 1
mptbase: ioc0: Sending Config request type 9, page 0 and action 0
mptbase: ioc0: Sending Config request type 9, page 0 and action 1
scsi8 : ioc0: LSI53C1030 C0, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=74
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
GSI 44 (level, low) -> CPU 3 (0x0c00) vector 75
ACPI: PCI Interrupt 0000:38:01.1[B] -> GSI 44 (level, low) -> IRQ 75
mptbase: ioc1: Initiating bringup
ioc1: LSI53C1030 C0: Capabilities={Initiator,Target}
mptbase: ioc1: Sending Config request type 3, page 0 and action 0
scsi 8:0:0:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:0: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 3, page 0 and action 1
mptbase: ioc1: Sending Config request type 3, page 2 and action 0
mptbase: ioc1: Sending Config request type 3, page 2 and action 6
mptbase: ioc1: Sending Config request type 4, page 1 and action 0
mptbase: ioc1: Sending Config request type 4, page 0 and action 0
mptbase: ioc1: Sending Config request type 1, page 1 and action 0
mptbase: ioc1: Sending Config request type 1, page 1 and action 1
mptbase: ioc1: Sending Config request type 1, page 4 and action 0
mptbase: ioc1: Sending Config request type 1, page 4 and action 1
mptbase: ioc1: Sending Config request type 0, page 2 and action 0
mptbase: ioc1: Sending Config request type 0, page 2 and action 1
mptbase: ioc1: Sending Config request type 9, page 0 and action 0
mptbase: ioc1: Sending Config request type 9, page 0 and action 1
scsi9 : ioc1: LSI53C1030 C0, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=75
scsi 1:0:2:0: CD-ROM HP DVD-ROM 305 1.01 PQ: 0 ANSI: 2
target1:0:2: Beginning Domain Validation
target1:0:2: asynchronous
target1:0:2: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 16)
target1:0:2: Domain Validation skipping write tests
target1:0:2: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mice: PS/2 mouse device common for all mice
EFI Variables Facility v0.08 2004-May-17
scsi 9:0:0:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:0: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:0: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 9:0:1:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:1: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:1: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 9:0:2:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:2: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:2: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 9:0:3:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:3: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:3: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:3: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 9:0:4:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:4: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:4: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:4: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 9:0:5:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:5: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:5: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:5: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 9:0:8:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target9:0:8: Beginning Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:8: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
target9:0:8: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc1: Sending Config request type 4, page 0 and action 1
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
scsi 2:0:6:0: Direct-Access HP 36.4G ST336753LC HPC3 PQ: 0 ANSI: 3
target2:0:6: tagged command queuing enabled, command queue depth 16.
target2:0:6: Beginning Domain Validation
target2:0:6: asynchronous
target2:0:6: wide asynchronous
target2:0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 31)
target2:0:6: Domain Validation skipping write tests
target2:0:6: Ending Domain Validation
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
scsi: waiting for bus probes to complete ...
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc1: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:0: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:1:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:1: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 0:0:6:0: Direct-Access HP 36.4G ST336753LC HPC3 PQ: 0 ANSI: 3
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:1: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:2:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:2: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:2: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:3:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:3: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:3: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:3: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:4:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:4: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:4: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:4: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:5:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:5: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:5: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:5: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:8:0: Direct-Access COMPAQ BF036863B9 HPB4 PQ: 0 ANSI: 3
target8:0:8: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:8: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:8: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI PCOMP (6.25 ns, offset 127)
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
scsi 8:0:15:0: Processor COMPAQ PROLIANT 4L7E*DB 2.14 PQ: 0 ANSI: 2
target8:0:15: Beginning Domain Validation
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
mptbase: ioc0: Sending Config request type 4, page 1 and action 2
target8:0:15: Ending Domain Validation
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target8:0:15: asynchronous
mptbase: ioc0: Sending Config request type 4, page 0 and action 1
target0:0:6: tagged command queuing enabled, command queue depth 16.
target0:0:6: Beginning Domain Validation
target0:0:6: asynchronous
target0:0:6: wide asynchronous
target0:0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 31)
target0:0:6: Domain Validation skipping write tests
target0:0:6: Ending Domain Validation
sd 0:0:6:0: [sda] 71132960 512-byte hardware sectors (36420 MB)
sd 0:0:6:0: [sda] Write Protect is off
sd 0:0:6:0: [sda] Mode Sense: d3 00 10 08
sd 0:0:6:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 0:0:6:0: [sda] 71132960 512-byte hardware sectors (36420 MB)
sd 0:0:6:0: [sda] Write Protect is off
sd 0:0:6:0: [sda] Mode Sense: d3 00 10 08
sd 0:0:6:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10
sd 0:0:6:0: [sda] Attached SCSI disk
sd 2:0:6:0: [sdb] 71132960 512-byte hardware sectors (36420 MB)
sd 2:0:6:0: [sdb] Write Protect is off
sd 2:0:6:0: [sdb] Mode Sense: d3 00 10 08
sd 2:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 2:0:6:0: [sdb] 71132960 512-byte hardware sectors (36420 MB)
sd 2:0:6:0: [sdb] Write Protect is off
sd 2:0:6:0: [sdb] Mode Sense: d3 00 10 08
sd 2:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9 sdb10
sd 2:0:6:0: [sdb] Attached SCSI disk
sd 8:0:0:0: [sdc] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: e7 00 10 08
sd 8:0:0:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:0:0: [sdc] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: e7 00 10 08
sd 8:0:0:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdc: sdc1 sdc2 sdc3
sd 8:0:0:0: [sdc] Attached SCSI disk
sd 8:0:1:0: [sdd] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:1:0: [sdd] Write Protect is off
sd 8:0:1:0: [sdd] Mode Sense: e7 00 10 08
sd 8:0:1:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:1:0: [sdd] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:1:0: [sdd] Write Protect is off
sd 8:0:1:0: [sdd] Mode Sense: e7 00 10 08
sd 8:0:1:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdd: sdd1 sdd2 sdd3
sd 8:0:1:0: [sdd] Attached SCSI disk
sd 8:0:2:0: [sde] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:2:0: [sde] Write Protect is off
sd 8:0:2:0: [sde] Mode Sense: e7 00 10 08
sd 8:0:2:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:2:0: [sde] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:2:0: [sde] Write Protect is off
sd 8:0:2:0: [sde] Mode Sense: e7 00 10 08
sd 8:0:2:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
sde:<4>GPT:disk_guids don't match.
GPT:partition_entry_array_crc32 values don't match: 0x413661e0 != 0x36c03570
GPT: Use GNU Parted to correct GPT errors.
sde1 sde2 sde3
sd 8:0:2:0: [sde] Attached SCSI disk
sd 8:0:3:0: [sdf] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:3:0: [sdf] Write Protect is off
sd 8:0:3:0: [sdf] Mode Sense: e7 00 10 08
sd 8:0:3:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:3:0: [sdf] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:3:0: [sdf] Write Protect is off
sd 8:0:3:0: [sdf] Mode Sense: e7 00 10 08
sd 8:0:3:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdf: sdf1 sdf2 sdf3
sd 8:0:3:0: [sdf] Attached SCSI disk
sd 8:0:4:0: [sdg] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:4:0: [sdg] Write Protect is off
sd 8:0:4:0: [sdg] Mode Sense: e7 00 10 08
sd 8:0:4:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:4:0: [sdg] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:4:0: [sdg] Write Protect is off
sd 8:0:4:0: [sdg] Mode Sense: e7 00 10 08
sd 8:0:4:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdg: sdg1 sdg2 sdg3
sd 8:0:4:0: [sdg] Attached SCSI disk
sd 8:0:5:0: [sdh] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:5:0: [sdh] Write Protect is off
sd 8:0:5:0: [sdh] Mode Sense: e7 00 10 08
sd 8:0:5:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:5:0: [sdh] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:5:0: [sdh] Write Protect is off
sd 8:0:5:0: [sdh] Mode Sense: e7 00 10 08
sd 8:0:5:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdh: sdh1
sd 8:0:5:0: [sdh] Attached SCSI disk
sd 8:0:8:0: [sdi] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:8:0: [sdi] Write Protect is off
sd 8:0:8:0: [sdi] Mode Sense: e7 00 10 08
sd 8:0:8:0: [sdi] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:8:0: [sdi] 71132000 512-byte hardware sectors (36420 MB)
sd 8:0:8:0: [sdi] Write Protect is off
sd 8:0:8:0: [sdi] Mode Sense: e7 00 10 08
sd 8:0:8:0: [sdi] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdi:<6>sd 8:0:8:0: [sdi] Sense Key : 0x1 [current]
sd 8:0:8:0: [sdi] ASC=0x5d ASCQ=0x32
sdi1
sd 8:0:8:0: [sdi] Attached SCSI disk
sd 9:0:0:0: [sdj] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:0:0: [sdj] Write Protect is off
sd 9:0:0:0: [sdj] Mode Sense: e7 00 10 08
sd 9:0:0:0: [sdj] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:0:0: [sdj] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:0:0: [sdj] Write Protect is off
sd 9:0:0:0: [sdj] Mode Sense: e7 00 10 08
sd 9:0:0:0: [sdj] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdj: sdj1
sd 9:0:0:0: [sdj] Attached SCSI disk
sd 9:0:1:0: [sdk] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:1:0: [sdk] Write Protect is off
sd 9:0:1:0: [sdk] Mode Sense: e7 00 10 08
sd 9:0:1:0: [sdk] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:1:0: [sdk] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:1:0: [sdk] Write Protect is off
sd 9:0:1:0: [sdk] Mode Sense: e7 00 10 08
sd 9:0:1:0: [sdk] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdk: sdk1
sd 9:0:1:0: [sdk] Attached SCSI disk
sd 9:0:2:0: [sdl] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:2:0: [sdl] Write Protect is off
sd 9:0:2:0: [sdl] Mode Sense: e7 00 10 08
sd 9:0:2:0: [sdl] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:2:0: [sdl] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:2:0: [sdl] Write Protect is off
sd 9:0:2:0: [sdl] Mode Sense: e7 00 10 08
sd 9:0:2:0: [sdl] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdl: sdl1
sd 9:0:2:0: [sdl] Attached SCSI disk
sd 9:0:3:0: [sdm] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:3:0: [sdm] Write Protect is off
sd 9:0:3:0: [sdm] Mode Sense: e7 00 10 08
sd 9:0:3:0: [sdm] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:3:0: [sdm] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:3:0: [sdm] Write Protect is off
sd 9:0:3:0: [sdm] Mode Sense: e7 00 10 08
sd 9:0:3:0: [sdm] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdm: sdm1
sd 9:0:3:0: [sdm] Attached SCSI disk
sd 9:0:4:0: [sdn] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:4:0: [sdn] Write Protect is off
sd 9:0:4:0: [sdn] Mode Sense: e7 00 10 08
sd 9:0:4:0: [sdn] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:4:0: [sdn] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:4:0: [sdn] Write Protect is off
sd 9:0:4:0: [sdn] Mode Sense: e7 00 10 08
sd 9:0:4:0: [sdn] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdn: sdn1
sd 9:0:4:0: [sdn] Attached SCSI disk
sd 9:0:5:0: [sdo] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:5:0: [sdo] Write Protect is off
sd 9:0:5:0: [sdo] Mode Sense: e7 00 10 08
sd 9:0:5:0: [sdo] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:5:0: [sdo] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:5:0: [sdo] Write Protect is off
sd 9:0:5:0: [sdo] Mode Sense: e7 00 10 08
sd 9:0:5:0: [sdo] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdo: sdo1 sdo2 sdo3
sd 9:0:5:0: [sdo] Attached SCSI disk
sd 9:0:8:0: [sdp] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:8:0: [sdp] Write Protect is off
sd 9:0:8:0: [sdp] Mode Sense: e7 00 10 08
sd 9:0:8:0: [sdp] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 9:0:8:0: [sdp] 71132000 512-byte hardware sectors (36420 MB)
sd 9:0:8:0: [sdp] Write Protect is off
sd 9:0:8:0: [sdp] Mode Sense: e7 00 10 08
sd 9:0:8:0: [sdp] Write cache: disabled, read cache: enabled, supports DPO and FUA
sdp: sdp1
sd 9:0:8:0: [sdp] Attached SCSI disk
-----------------------------------------------
task blocked log when I leave the system in the hung state for a couple of minutes:
INFO: task swapper:1 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
swapper D a0000001006cc530 0 1 0
Call Trace:
[<a0000001006caa70>] schedule+0xa30/0x1e80
sp=e00007018143fd80 bsp=e000070181438e58
[<a0000001006cc530>] schedule_timeout+0x110/0x1a0
sp=e00007018143fda0 bsp=e000070181438e28
[<a0000001006c9d40>] wait_for_common+0x1a0/0x300
sp=e00007018143fdd0 bsp=e000070181438dd0
[<a0000001006ca020>] wait_for_completion+0x40/0x60
sp=e00007018143fe00 bsp=e000070181438db0
[<a0000001004ceba0>] scsi_complete_async_scans+0x1c0/0x240
sp=e00007018143fe00 bsp=e000070181438d68
[<a0000001008305b0>] kernel_init+0x330/0x820
sp=e00007018143fe00 bsp=e000070181438d08
[<a000000100012ab0>] kernel_thread_helper+0x30/0x60
sp=e00007018143fe30 bsp=e000070181438ce0
[<a0000001000089c0>] start_kernel_thread+0x20/0x40
sp=e00007018143fe30 bsp=e000070181438ce0
INFO: task scsi_scan_8:1231 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
scsi_scan_8 D a0000001006cc530 0 1231 2
Call Trace:
[<a0000001006caa70>] schedule+0xa30/0x1e80
sp=e000070182777cb0 bsp=e000070182771098
[<a0000001006cc530>] schedule_timeout+0x110/0x1a0
sp=e000070182777cd0 bsp=e000070182771068
[<a0000001006c9d40>] wait_for_common+0x1a0/0x300
sp=e000070182777d00 bsp=e000070182771018
[<a0000001006ca020>] wait_for_completion+0x40/0x60
sp=e000070182777d30 bsp=e000070182770ff0
[<a0000001002e6da0>] blk_execute_rq+0xe0/0x240
sp=e000070182777d30 bsp=e000070182770fb0
[<a0000001004cc7c0>] scsi_execute+0x180/0x1e0
sp=e000070182777dc0 bsp=e000070182770f58
[<a0000001004cc8f0>] scsi_execute_req+0xd0/0x160
sp=e000070182777dc0 bsp=e000070182770ef0
[<a0000001004d1100>] __scsi_scan_target+0x4c0/0xc40
sp=e000070182777dd0 bsp=e000070182770e70
[<a0000001004d1950>] scsi_scan_channel+0xd0/0x160
sp=e000070182777e30 bsp=e000070182770e18
[<a0000001004d1ac0>] scsi_scan_host_selected+0xe0/0x240
sp=e000070182777e30 bsp=e000070182770dc0
[<a0000001004d1dd0>] do_scsi_scan_host+0x1b0/0x1e0
sp=e000070182777e30 bsp=e000070182770d88
[<a0000001004d1e30>] do_scan_async+0x30/0x300
sp=e000070182777e30 bsp=e000070182770d38
[<a0000001000c7570>] kthread+0x110/0x180
sp=e000070182777e30 bsp=e000070182770d08
[<a000000100012ab0>] kernel_thread_helper+0x30/0x60
sp=e000070182777e30 bsp=e000070182770ce0
[<a0000001000089c0>] start_kernel_thread+0x20/0x40
sp=e000070182777e30 bsp=e000070182770ce0
INFO: task scsi_scan_9:1300 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
scsi_scan_9 D a0000001006cc530 0 1300 2
Call Trace:
[<a0000001006caa70>] schedule+0xa30/0x1e80
sp=e000070182917db0 bsp=e000070182910e30
[<a0000001006cc530>] schedule_timeout+0x110/0x1a0
sp=e000070182917dd0 bsp=e000070182910e00
[<a0000001006c9d40>] wait_for_common+0x1a0/0x300
sp=e000070182917e00 bsp=e000070182910da8
[<a0000001006ca020>] wait_for_completion+0x40/0x60
sp=e000070182917e30 bsp=e000070182910d88
[<a0000001004d1ee0>] do_scan_async+0xe0/0x300
sp=e000070182917e30 bsp=e000070182910d38
[<a0000001000c7570>] kthread+0x110/0x180
sp=e000070182917e30 bsp=e000070182910d08
[<a000000100012ab0>] kernel_thread_helper+0x30/0x60
sp=e000070182917e30 bsp=e000070182910ce0
[<a0000001000089c0>] start_kernel_thread+0x20/0x40
sp=e000070182917e30 bsp=e000070182910ce0
<repeats ad nauseum>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan
2007-12-06 19:01 ` Lee Schermerhorn
@ 2007-12-11 18:23 ` Lee Schermerhorn
0 siblings, 0 replies; 8+ messages in thread
From: Lee Schermerhorn @ 2007-12-11 18:23 UTC (permalink / raw)
To: Andrew Morton; +Cc: linux-scsi, James.Bottomley, Eric.Moore, Eric Whitney
On Thu, 2007-12-06 at 14:01 -0500, Lee Schermerhorn wrote:
> On Thu, 2007-12-06 at 10:35 -0800, Andrew Morton wrote:
> > On Thu, 06 Dec 2007 13:14:22 -0500 Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> >
> > > On Wed, 2007-12-05 at 13:20 -0800, Andrew Morton wrote:
> > > > On Wed, 05 Dec 2007 11:36:39 -0500
> > > > Lee Schermerhorn <Lee.Schermerhorn@hp.com> wrote:
> > > >
> > > > > As reported here:
> > > > >
> > > > > http://marc.info/?l=linux-scsi&m=119645761124683&w=4
> > > > >
> > > > > against 24-rc3-mm2, I'm still seeing the hang on my HP ia64 NUMA
> > > > > platform under 24-rc4-mm1 with async scsi scan enabled. I'm still
> > > > > seeing the message "mptspi: ioc#: mpt_config failed" when it hangs.
> > > > >
> > > > > I can boot by disabling async scan. However, I've also noticed some
> > > > > disks attached via one of the "mpt" adapters ["scsi8" in console long in
> > > > > message linked above] going "off-line" during stress tests. This was
> > > > > under 24-rc3-mm2. Haven't got that far yet with 24-rc4-mm1.
> > > > >
> > > >
> > > > Is ther any way of tricking you into
> > > > http://www.zip.com.au/~akpm/linux/patches/stuff/bisecting-mm-trees.txt?
> > > >
> > > > Obvious culprits to start with would be git-scsi-misc and maybe
> > > > scsi-early-detection-of-medium-not-present-updated.patch. But there are
> > > > only 20-odd scsi patches in there.
> > >
> > > The reported hang occurs after pushing the git-scsi-misc patch.
> >
After trying a few "suspect" hunks of the git-scsi-misc.patch, I have
verified that the commit 8655a546c83fc43f0a73416bbd126d02de7ad6c0--as
discussed in http://marc.info/?t=119689824100001&r=1&w=4 for a
different symptom--seems to be the culprit. Reverting this patch allows
me to boot with async scsi scan enabled. I'm starting a stress test to
verify that this fixes the "disk going off-line" issue that I saw
earlier.
Lee
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2007-12-11 18:23 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-12-05 16:36 BUG 2.6.24-rc4-mm1 -- Boot still hangs w/ async scsi scan Lee Schermerhorn
2007-12-05 21:20 ` Andrew Morton
2007-12-05 21:44 ` Lee Schermerhorn
2007-12-06 18:14 ` Lee Schermerhorn
2007-12-06 18:35 ` Andrew Morton
2007-12-06 19:01 ` Lee Schermerhorn
2007-12-11 18:23 ` Lee Schermerhorn
2007-12-07 19:38 ` Lee Schermerhorn
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).