From mboxrd@z Thu Jan 1 00:00:00 1970 From: James Bottomley Subject: Re: [BUG] 2.6.24-git usb reset problems Date: Tue, 29 Jan 2008 14:33:15 -0500 Message-ID: <1201635195.3069.36.camel@localhost.localdomain> References: <20080128204935.GI15220@kernel.dk> <479F32E9.10609@panasas.com> <20080129141108.GV15220@kernel.dk> <200801291531.39825.oliver@neukum.org> <20080129143109.GW15220@kernel.dk> <20080129183910.GI15220@kernel.dk> <20080129191024.GO14375@one-eyed-alien.net> Mime-Version: 1.0 Content-Type: text/plain Content-Transfer-Encoding: 7bit Return-path: Received: from accolon.hansenpartnership.com ([76.243.235.52]:34696 "EHLO accolon.hansenpartnership.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752460AbYA2TdY (ORCPT ); Tue, 29 Jan 2008 14:33:24 -0500 In-Reply-To: <20080129191024.GO14375@one-eyed-alien.net> Sender: linux-scsi-owner@vger.kernel.org List-Id: linux-scsi@vger.kernel.org To: Matthew Dharm Cc: Jens Axboe , Oliver Neukum , Boaz Harrosh , Greg KH , linux-kernel@vger.kernel.org, linux-usb@vger.kernel.org, linux-scsi@vger.kernel.org On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote: > On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote: > > On Tue, Jan 29 2008, Jens Axboe wrote: > > > On Tue, Jan 29 2008, Oliver Neukum wrote: > > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe: > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe wrote: > > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > > > >> Greg KH wrote: > > > > > > > > > > > No difference, still just a lot of resets. > > > > > > > > > > > > > Where you able to figure out which usb storage transport is used? > > > > > > > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport() > > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will > > > > > > pinpoint better where to look. Let me research a bit. > > > > > > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and > > > > > transport is 'Bulk' > > > > > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG > > > > That should tell the reason for the resets. > > > > > > Sure, I'll do that. Will post the results tonight. > > > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged > > in the device, waited 10 seconds or so and pulled it out. These are the > > messages. > > > > It all looks good until the MODE_SENSE command, where it only transfers > > 4 of 192 bytes. > > No, that's not the problem. This is the problem: > > > usb-storage: *** thread awakened. > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > usb-storage: 00 00 00 00 00 00 > > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6 > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > > usb-storage: Status code 0; transferred 31/31 > > usb-storage: -- transfer complete > > usb-storage: Bulk command transfer result=0 > > usb-storage: Attempting to get CSW... > > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes > > usb-storage: Status code 0; transferred 13/13 > > usb-storage: -- transfer complete > > usb-storage: Bulk status result = 0 > > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1 > > usb-storage: -- transport indicates command failure > > usb-storage: Issuing auto-REQUEST_SENSE > > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6 > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > > usb-storage: Status code 0; transferred 31/31 > > usb-storage: -- transfer complete > > usb-storage: Bulk command transfer result=0 > > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries > > usb-storage: usb_sg_init returned -22 > > usb-storage: Bulk data transfer result 0x4 > > usb-storage: -- auto-sense failure > > usb-storage: storage_pre_reset > > ehci_hcd 0000:00:1d.7: port 1 high speed > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT > > usb 5-1: reset high speed USB device using ehci_hcd and address 2 > > ehci_hcd 0000:00:1d.7: port 1 high speed > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT > > usb-storage: storage_post_reset > > usb-storage: usb_reset_composite_device returns 0 > > usb-storage: scsi cmd done, result=0x70000 > > usb-storage: *** thread sleeping. > > For some reason, usb_sg_init is boned during auto-sense. OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense code ... that was also an update in 2.6.24 James