From: Saurav Kashyap <saurav.kashyap@qlogic.com>
To: jbottomley@parallels.com
Cc: giridhar.malavali@qlogic.com, saurav.kashyap@qlogic.com,
andrew.vasquez@qlogic.com, linux-scsi@vger.kernel.org
Subject: [PATCH 23/29] qla2xxx: Select link initialization option bits from current operating mode.
Date: Tue, 27 Aug 2013 01:37:49 -0400 [thread overview]
Message-ID: <1377581875-8574-24-git-send-email-saurav.kashyap@qlogic.com> (raw)
In-Reply-To: <1377581875-8574-1-git-send-email-saurav.kashyap@qlogic.com>
From: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
---
drivers/scsi/qla2xxx/qla_mbx.c | 6 +++++-
1 files changed, 5 insertions(+), 1 deletions(-)
diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c
index 1261884..c825d1d 100644
--- a/drivers/scsi/qla2xxx/qla_mbx.c
+++ b/drivers/scsi/qla2xxx/qla_mbx.c
@@ -1667,7 +1667,11 @@ qla24xx_link_initialize(scsi_qla_host_t *vha)
return QLA_FUNCTION_FAILED;
mcp->mb[0] = MBC_LINK_INITIALIZATION;
- mcp->mb[1] = BIT_6|BIT_4;
+ mcp->mb[1] = BIT_4;
+ if (vha->hw->operating_mode == LOOP)
+ mcp->mb[1] |= BIT_6;
+ else
+ mcp->mb[1] |= BIT_5;
mcp->mb[2] = 0;
mcp->mb[3] = 0;
mcp->out_mb = MBX_3|MBX_2|MBX_1|MBX_0;
--
1.7.7
next prev parent reply other threads:[~2013-08-27 6:06 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-27 5:37 [PATCH 00/29] Update driver to 8.06.00.08-k Saurav Kashyap
2013-08-27 5:37 ` [PATCH 01/29] qla2xxx: Print some variables to hexadecimal string via %*phN format Saurav Kashyap
2013-08-27 5:37 ` [PATCH 02/29] qla2xxx: Add support for ISP8044 Saurav Kashyap
2013-08-28 7:15 ` James Bottomley
2013-08-28 13:33 ` Saurav Kashyap
2013-08-27 5:37 ` [PATCH 03/29] qla2xxx: Fix incorrect test after list_for_each_entry() exits Saurav Kashyap
2013-08-27 5:37 ` [PATCH 04/29] qla2xxx: Correct multiqueue offset calculations Saurav Kashyap
2013-08-27 5:37 ` [PATCH 05/29] qla2xxx: Set factory reset recovery timeout to 10 min. for ISPFX00 Saurav Kashyap
2013-08-27 5:37 ` [PATCH 06/29] qla2xxx: Perform warm reset every 2 minutes if firmware load fails " Saurav Kashyap
2013-08-27 5:37 ` [PATCH 07/29] qla2xxx: Add ISPFX00 specific bus reset routine Saurav Kashyap
2013-08-27 5:37 ` [PATCH 08/29] qla2xxx: Remove QL_DEBUG_LEVEL_17 defines from qla_nx.c Saurav Kashyap
2013-08-27 5:37 ` [PATCH 09/29] qla2xxx: Add setting of driver version string for vendor application Saurav Kashyap
2013-08-27 5:37 ` [PATCH 10/29] qla2xxx: Reconfigure thermal temperature Saurav Kashyap
2013-08-27 5:37 ` [PATCH 11/29] qla2xxx: Notify ISPFX00 firmware when driver is unloaded or system is shut down Saurav Kashyap
2013-08-27 5:37 ` [PATCH 12/29] qla2xxx: Add critical temperature handling for ISPFX00 Saurav Kashyap
2013-08-27 5:37 ` [PATCH 13/29] qla2xxx: Make log message that prints when a completion status requires a port down more readable Saurav Kashyap
2013-08-27 5:37 ` [PATCH 14/29] qla2xxx: Add missing FCP statistics to sysfs interface Saurav Kashyap
2013-08-27 5:37 ` [PATCH 15/29] qla2xxx: Add changes to support extended IOs for ISPFX00 Saurav Kashyap
2013-08-27 5:37 ` [PATCH 16/29] qla2xxx: Add changes in initialization for ISPFX00 cards with BIOS Saurav Kashyap
2013-08-27 5:37 ` [PATCH 17/29] qla2xxx: Send all AENs for ISPFx00 to above layers Saurav Kashyap
2013-08-27 5:37 ` [PATCH 18/29] qla2xxx: Remove handling of Shutdown Requested AEN from qlafx00_process_aen() Saurav Kashyap
2013-08-27 5:37 ` [PATCH 19/29] qla2xxx: Correct Interrupt Register offset for ISPFX00 Saurav Kashyap
2013-08-27 5:37 ` [PATCH 20/29] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN Saurav Kashyap
2013-08-27 5:37 ` [PATCH 21/29] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it Saurav Kashyap
2013-08-27 5:37 ` [PATCH 22/29] qla2xxx: Add loopback IDC-TIME-EXTEND aen handling support Saurav Kashyap
2013-08-27 5:37 ` Saurav Kashyap [this message]
2013-08-27 5:37 ` [PATCH 24/29] qla2xxx: Move queue depth ramp down message to i/o debug level Saurav Kashyap
2013-08-27 5:37 ` [PATCH 25/29] qla2xxx: Add a new interface to update versions Saurav Kashyap
2013-08-27 5:37 ` [PATCH 26/29] qla2xxx: Correctly print out/in mailbox registers Saurav Kashyap
2013-08-27 5:37 ` [PATCH 27/29] qla2xxx: Correction to message ids Saurav Kashyap
2013-08-27 5:37 ` [PATCH 28/29] qla2xxx: print MAC via %pMR Saurav Kashyap
2013-08-27 5:37 ` [PATCH 29/29] qla2xxx: Update the driver version to 8.06.00.08-k Saurav Kashyap
2013-08-28 3:24 ` [PATCH 00/29] Update driver " James Bottomley
2013-08-28 4:31 ` Saurav Kashyap
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1377581875-8574-24-git-send-email-saurav.kashyap@qlogic.com \
--to=saurav.kashyap@qlogic.com \
--cc=andrew.vasquez@qlogic.com \
--cc=giridhar.malavali@qlogic.com \
--cc=jbottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).