From: Saurav Kashyap <saurav.kashyap@qlogic.com>
To: jbottomley@parallels.com
Cc: giridhar.malavali@qlogic.com, saurav.kashyap@qlogic.com,
andrew.vasquez@qlogic.com, linux-scsi@vger.kernel.org
Subject: [PATCH 03/22] qla2xxx: Disable INTx interrupt for ISP82XX
Date: Wed, 30 Oct 2013 03:38:10 -0400 [thread overview]
Message-ID: <1383118709-5569-4-git-send-email-saurav.kashyap@qlogic.com> (raw)
In-Reply-To: <1383118709-5569-1-git-send-email-saurav.kashyap@qlogic.com>
From: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
---
drivers/scsi/qla2xxx/qla_isr.c | 13 +++++++------
1 files changed, 7 insertions(+), 6 deletions(-)
diff --git a/drivers/scsi/qla2xxx/qla_isr.c b/drivers/scsi/qla2xxx/qla_isr.c
index ff9c86b..6e649d7 100644
--- a/drivers/scsi/qla2xxx/qla_isr.c
+++ b/drivers/scsi/qla2xxx/qla_isr.c
@@ -2937,7 +2937,7 @@ msix_out:
int
qla2x00_request_irqs(struct qla_hw_data *ha, struct rsp_que *rsp)
{
- int ret;
+ int ret = QLA_FUNCTION_FAILED;
device_reg_t __iomem *reg = ha->iobase;
scsi_qla_host_t *vha = pci_get_drvdata(ha->pdev);
@@ -2971,10 +2971,12 @@ qla2x00_request_irqs(struct qla_hw_data *ha, struct rsp_que *rsp)
ha->chip_revision, ha->fw_attributes);
goto clear_risc_ints;
}
- ql_log(ql_log_info, vha, 0x0037,
- "MSI-X Falling back-to MSI mode -%d.\n", ret);
+
skip_msix:
+ ql_log(ql_log_info, vha, 0x0037,
+ "Falling back-to MSI mode -%d.\n", ret);
+
if (!IS_QLA24XX(ha) && !IS_QLA2532(ha) && !IS_QLA8432(ha) &&
!IS_QLA8001(ha) && !IS_P3P_TYPE(ha) && !IS_QLAFX00(ha))
goto skip_msi;
@@ -2986,14 +2988,13 @@ skip_msix:
ha->flags.msi_enabled = 1;
} else
ql_log(ql_log_warn, vha, 0x0039,
- "MSI-X; Falling back-to INTa mode -- %d.\n", ret);
+ "Falling back-to INTa mode -- %d.\n", ret);
+skip_msi:
/* Skip INTx on ISP82xx. */
if (!ha->flags.msi_enabled && IS_QLA82XX(ha))
return QLA_FUNCTION_FAILED;
-skip_msi:
-
ret = request_irq(ha->pdev->irq, ha->isp_ops->intr_handler,
ha->flags.msi_enabled ? 0 : IRQF_SHARED,
QLA2XXX_DRIVER_NAME, rsp);
--
1.7.7
next prev parent reply other threads:[~2013-10-30 8:11 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-10-30 7:38 [PATCH 00/22] qla2xxx: Patches for 3.13 scsi "misc" branch Saurav Kashyap
2013-10-30 7:38 ` [PATCH 01/22] qla2xxx: Print proper QLAFX00 product name at probe Saurav Kashyap
2013-10-30 7:38 ` [PATCH 02/22] qla2xxx: Honor execute firmware failures Saurav Kashyap
2013-10-30 7:38 ` Saurav Kashyap [this message]
2013-10-30 7:38 ` [PATCH 04/22] qla2xxx: Correctly set mailboxes for extended init control block Saurav Kashyap
2013-10-30 7:38 ` [PATCH 05/22] qla2xxx: Add BPM support for ISP25xx Saurav Kashyap
2013-10-30 7:38 ` [PATCH 06/22] qla2xxx: Don't consider the drivers knocked out of IDC participation for future reset recovery process Saurav Kashyap
2013-10-30 7:38 ` [PATCH 07/22] Revert "qla2xxx: Ramp down queue depth for attached SCSI devices when driver resources are low." Saurav Kashyap
2013-10-30 7:38 ` [PATCH 08/22] qla2xxx: Refactor shutdown code so some functionality can be reused Saurav Kashyap
2013-10-30 7:38 ` [PATCH 09/22] qla2xxx: Disable adapter when we encounter a PCI disconnect Saurav Kashyap
2013-10-30 7:38 ` [PATCH 10/22] qla2xxx: Fix issue with not displaying node name after system reboot Saurav Kashyap
2013-10-30 7:38 ` [PATCH 11/22] qla2xxx: Add BSG interface for read/write serdes register Saurav Kashyap
2013-10-30 7:38 ` [PATCH 12/22] qla2xxx: Fix undefined behavior in call to snprintf() Saurav Kashyap
2013-10-30 7:38 ` [PATCH 13/22] qla2xxx: Clear RISC INT reg only for an event and not always while polling Saurav Kashyap
2013-10-30 7:38 ` [PATCH 14/22] qla2xxx: Add logic to abort BSG commands for ISPFX00 Saurav Kashyap
2013-10-30 7:38 ` [PATCH 15/22] qla2xxx: Add changes to obtain ISPFX00 adapters product information in accordance with firmware update Saurav Kashyap
2013-10-30 7:38 ` [PATCH 16/22] qla2xxx: Use the correct mailbox registers when acknowledging an IDC request on ISP8044 Saurav Kashyap
2013-10-30 7:38 ` [PATCH 17/22] qla2xxx: Use scnprintf() instead of snprintf() in the sysfs handlers Saurav Kashyap
2013-10-30 7:38 ` [PATCH 18/22] qla2xxx: Only complete dcbx_comp and lb_portup_comp for virtual port index 0 Saurav Kashyap
2013-10-30 7:38 ` [PATCH 19/22] qla2xxx: Reset nic_core_reset_owner on moving from COLD to READY for ISP8044 Saurav Kashyap
2013-10-30 7:38 ` [PATCH 20/22] qla2xxx: Replace a constant with a macro definition for host->canqueue assigmnment Saurav Kashyap
2013-10-30 7:38 ` [PATCH 21/22] qla2xxx: Adding MAINTAINERS for qla2xxx FC-SCSI driver Saurav Kashyap
2013-10-30 7:38 ` [PATCH 22/22] qla2xxx: Update the driver version to 8.06.00.12-k Saurav Kashyap
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1383118709-5569-4-git-send-email-saurav.kashyap@qlogic.com \
--to=saurav.kashyap@qlogic.com \
--cc=andrew.vasquez@qlogic.com \
--cc=giridhar.malavali@qlogic.com \
--cc=jbottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).